ID FD PA Logic System
-
Upload
gaurav-tiwari -
Category
Documents
-
view
44 -
download
0
description
Transcript of ID FD PA Logic System
![Page 1: ID FD PA Logic System](https://reader035.fdocuments.in/reader035/viewer/2022081420/55cf970f550346d0338f8b8f/html5/thumbnails/1.jpg)
April 19, 2023 PMI Revision 00 1
ID/FD FAN LOGIC SYSTEM
![Page 2: ID FD PA Logic System](https://reader035.fdocuments.in/reader035/viewer/2022081420/55cf970f550346d0338f8b8f/html5/thumbnails/2.jpg)
April 19, 2023 PMI Revision 00 2
P&I OF BOILER AUXILLARIES A. FD FAN START PERMISSIVES
• Blade pitch position minimum.
• Discharge damper fully closed.
• Lube oil pressure adequate.
• Control oil pressure adequate.
• Oil tank level normal.
• Bearing temperature not high.
• One ID Fan running AND other FD fan not running.
OR Both ID Fan running
![Page 3: ID FD PA Logic System](https://reader035.fdocuments.in/reader035/viewer/2022081420/55cf970f550346d0338f8b8f/html5/thumbnails/3.jpg)
April 19, 2023 PMI Revision 00 3
TRIPS
• Fan bearing temperature very high
• Post purge furnace pressure very high/ very low
• Outlet damper fail to open in set time (3 min)
• No ID fan running or one ID fan and one FD fan
already in service.
![Page 4: ID FD PA Logic System](https://reader035.fdocuments.in/reader035/viewer/2022081420/55cf970f550346d0338f8b8f/html5/thumbnails/4.jpg)
April 19, 2023 PMI Revision 00 4
PA FAN START PERMISSIVES
• Blade pitch minimum• Lube oil pressure adequate• Control oil pressure adequate• Bearing temp. not high• Discharge damper closed. • Lube oil tank level adequate • No MFT & Cold air damper closed• At least one FD fan is running and • PAPH A/B in service & respective air inlet/ outlet
dampers are open
![Page 5: ID FD PA Logic System](https://reader035.fdocuments.in/reader035/viewer/2022081420/55cf970f550346d0338f8b8f/html5/thumbnails/5.jpg)
April 19, 2023 PMI Revision 00 5
TRIPS
• Fan bearing temperature very high.
• Trip from FSSS (MFT).
• Discharge damper fails to open.
![Page 6: ID FD PA Logic System](https://reader035.fdocuments.in/reader035/viewer/2022081420/55cf970f550346d0338f8b8f/html5/thumbnails/6.jpg)
April 19, 2023 PMI Revision 00 6
ID FAN START PERMISSIVES
• Hyd. coupling Scoop position minimum.
• Inlet guide vane position minimum.
• Bearing temperature not high.
• Oil temp. and oil level in Hyd. coupling OK.
• Lube oil pressure adequate.
• Both inlet and outlet dampers closed.
• Other ID fan not running or Any FD fan running.
![Page 7: ID FD PA Logic System](https://reader035.fdocuments.in/reader035/viewer/2022081420/55cf970f550346d0338f8b8f/html5/thumbnails/7.jpg)
April 19, 2023 PMI Revision 00 7
TRIP CONDITION
• Fan/Motor bearing temperature very high.
• Lube oil pressure very low.
• Post purge furnace pressure Hi/Low from FSSS.
• Discharge dampers/ suction damper fail to open
within specified time (3 min.)
• Hydraulic coupling bearing temp. very high
• Hydraulic coupling oil temp. very high.
![Page 8: ID FD PA Logic System](https://reader035.fdocuments.in/reader035/viewer/2022081420/55cf970f550346d0338f8b8f/html5/thumbnails/8.jpg)
April 19, 2023 PMI Revision 00 8
SGWC PUMPS: (CC Pumps)
PERMISSIVES
• Discharge valve 1 open.
• Discharge valve 2 open.
• Motor cavity temp. not high.
• Pump cavity – suction manifold differential
temp. not high.
• Motor cooling water flow adequate.
![Page 9: ID FD PA Logic System](https://reader035.fdocuments.in/reader035/viewer/2022081420/55cf970f550346d0338f8b8f/html5/thumbnails/9.jpg)
April 19, 2023 PMI Revision 00 9
TRIPS
• Any of the discharge valves not fully open.
• Motor cavity temp. high (60 deg. C) for more
than 5 Sec.
• Electrical protection trip/ EPB pressed.
![Page 10: ID FD PA Logic System](https://reader035.fdocuments.in/reader035/viewer/2022081420/55cf970f550346d0338f8b8f/html5/thumbnails/10.jpg)
April 19, 2023 PMI Revision 00 10
Run back operation• Tripping of PA Fan or FD Fan• PA header pressure low/very low• Sequential tripping of Mills/Feeders
![Page 11: ID FD PA Logic System](https://reader035.fdocuments.in/reader035/viewer/2022081420/55cf970f550346d0338f8b8f/html5/thumbnails/11.jpg)
April 19, 2023 PMI Revision 00 11