Icom IC-M802 Instruction Manual

8/8/2019 Icom IC-M802 Instruction Manual

1/78

MF/HF MARINE TRANSCEIVER

iM802

INSTRUCTION MANUAL


2/78

i

FOREWORD

Thank you for purchasing this Icom product. The IC-

M802 MF / HF MARINE TRANSCEIVER is designed and builtwith Icoms superior technology and craftsmanship.With proper care, this product should provide you withyears of trouble-free operation.

We want to take a couple of moments of your time tothank you for making the IC-M802 your radio of choice,and hope you agree with Icoms philosophy of tech-nology first. Many hours of research and develop-ment went into the design of your IC-M802.

D FEATURES

Standard 4 8 remote controller Built-in DSC meets ITU Class E requirement E-mail function available PC connection capability for remote control

IMPORTANT

READ THIS INSTRUCTION MANUAL

CAREFULLY before attempting to operate thetransceiver.

SAVE THIS INSTRUCTION MANUAL. Thismanual contains important safety and operating in-structions for the IC-M802.

EXPLICIT DEFINITIONS

R WARNING HIGH VOLTAGE! NEVER at-

tach an antenna or internal antenna connector duringtransmission. This may result in an electrical shock orburn.

R WARNING! NEVER connect the transceiver toan AC outlet directly. This may pose a fire hazard orresult in an electric shock.

R WARNING! NEVER mount the transceivermain unit overhead. The weight of the unit is approxi-mately 4.7 kg (10 lb 6 oz), but its apparent weight willincrease several fold due to wave shocks or vibration.The unit must be mounted on a at hard surface only.

R NEVER connect a power source of more than15.64 V DC, such as a 24 V battery. This connectioncould cause a re or ruin the transceiver.

R NEVER place the transceiver where normal oper-ation of the ship or vehicle may be hindered or where itcould cause bodily injury.

R NEVER let metal, wire or other objects touch anyinternal part or connectors on the rear panel of thetransceiver. This may result in an electric shock.

R NEVER expose the transceiver to rain, snow orany liquids.

DO NOT use chemical agents such as benzine or al-cohol when cleaning, as they can damage the trans-ceiver surface.

During maritime mobile operation, KEEP the trans-ceiver and microphone as far away as possible (atleast 1 m; 3 ft) from the magnetic navigation compassto prevent erroneous indications.

Use Icom microphones only (supplied). Other manu-facturers microphones have different pin assignments,and connection to the IC-M802 may damage the trans-ceiver.

AVOID using or placing the transceiver in areas withtemperatures below 20C (4F) or above +55C(+131F).

AVOID placing the transceiver in excessively dusty en-vironments or in direct sunlight.

AVOID placing the transceiver against walls or puttinganything on top of the transceiver. This will obstructheat dissipation.

Place the unit in a secure place to avoid inadvertentuse by children.

BE CAREFUL! The heatsink will become hot when op-erating the transceiver continuously for long periods.

PRECAUTIONS

WORD DEFINITION

R WARNINGPersonal injury, re hazard or electricshock may occur.

CAUTION Equipment damage may occur.

NOTEIf disregarded, inconvenience only. Norisk or personal injury, fire or electricshock.

Icom, Icom Inc. and the are registered trademarks ofIcom Incorporated (Japan) in the United States, the UnitedKingdom, Germany, France, Spain, Russia and/or othercountries.


3/78

ii

When your ship requires assistance, contact other

ships and the Coast Guard by sending a distress callusing digital selective calling on 2187.5 kHz.

IN CASE OF EMERGENCY

When immediate help is needed

q Push and hold [DISTRESS] for 5 sec. until theshort beeps become one long beep, to send thedistress call.

w After 2182 kHz is automatically selected (after anacknowledgement call is received), push and holdthe PTT switch on the microphone and send thefollowing information.

1. MAY DAY, MAY DAY, MAY DAY.2. THIS IS . . . . . . . . . (name of ship)

3. LOCATED AT . . . . (ships position)

4. Give the reason for the distress call.

5. Explain what assistance you need.

6. Give additional information:Ship typeShip lengthShip colorNumber of people on-board

When potential problems exist

q Push [DSC] to select DSC watch mode, if neces-sary.

w Push [MODE SET ] to select DSC menu, rotate [CH]to select All ships then push [ENT].

e Follow the guidance displayed on the LCD (bottomline), to set up the category, trafc frequency andcalling frequency with [CH], [ENT] and keypad.

r Push and hold [CANCEL/CALL] for 1 sec. until theshort beeps become one long beep.

t After an acknowledgement call is received, trans-mit the appropriate information using voice. DSC equipped ships may monitor your transmission.

FOREWORD................................................iIMPORTANT .............................................. iEXPLICIT DEFINITIONS ........................... iPRECAUTIONS ......................................... iIN CASE OF EMERGENCY ......................iiTABLE OF CONTENTS ............................ iiQUICK REFERENCE............................. IV

I How to set a Channel/Group .............. II Audio output/squelch adjustment ...... III

Basic voice transmission and reception.......................................................... IIII Receiving a DSC............................... IVI Transmitting a distress call................ IV

1 OPERATING RULES AND GUIDELINES............................................................... 1

2 PANEL DESCRIPTION .................... 27I Front panel Controller .................... 2I Front panel Main unit ...................... 4I Rear panel Main unit ...................... 5I Microphone (HM-135) ....................... 5I LCD screen ....................................... 6

3 SETTING A CHANNEL .................... 89I Selecting a channel ........................... 8

4 RECEIVE AND TRANSMIT .......... 1013I Basic voice transmit and receive .... 10I Functions for transmit ...................... 10I Functions for receive ....................... 11I CW operation .................................. 12I FSK operation ................................. 13

5 CHANNEL NAME PROGRAMMING..................................................... 14

6 DSC PREPARATION ................... 1516I MMSI code programming ................ 15I Position and time programming ....... 16

7 CALL PROCEDURE .................... 1736I Distress call ..................................... 17I Distress call to ships ........................ 21I Urgency call ..................................... 24I Safety call ........................................ 28I Routine call ...................................... 32I

Group call ........................................ 34I Position request call ........................ 35I Test call ........................................... 36

8 WHEN RECEIVING A CALL ........ 3742I To receive a DSC call ...................... 37I Received information ....................... 38I Deleting a memory .......................... 38I Distress call ..................................... 39I Distress relay call ............................ 39I All ships call ..................................... 40I Group call ........................................ 40I Geographical area call .................... 40I Individual call ................................... 41I Position request call ........................ 42

9 MEMORY OPERATION ..................... 43I Memory description ......................... 43I Memory writing ................................ 43I Memory reading/transmitting/deleting

......................................................... 4310DSC MENU OPERATION ............ 4446

I General ............................................ 44I ID input ............................................ 44

I Frequency input ............................... 45I Verifying self-ID ............................... 46I Memory reading/deleting ................. 46

11E-MAIL OPERATION ......................... 47I General ............................................ 47I Operation ......................................... 47

12SET MODE ................................... 4852I Quick set mode ............................... 48I Initial set mode ................................ 49

13CONNECTION AND INSTALLATION....................................................... 5362I Supplied accessories ...................... 53I Front panel connections ...................53I Rear panel connections ................... 54I Ground connection .......................... 55I Power source .................................. 55I Antenna ........................................... 56I Mounting .......................................... 57I Using the optional MB-75 ................ 58I Transceiver dimensions ................... 59I Fuse replacement ............................ 60I Connector information ..................... 61

14ANTENNA AND GROUNDINGCONSIDERATIONS ..................... 6365

15SPECIFICATIONS .............................. 6616TEMPLATE .................................. 6770

I Remote controller (RC-25) .............. 67I Speaker (SP-24) .............................. 69

17OPTIONS ........................................... 71

TABLE OF CONTENTS

1

23

4

5

6

78

9

10

11

12

13

14

15

16

17

Q u

i c k R e

f e r e n c e


4/78

Available channel groups and channels

*1[GRP] changes in 20 channels steps. * 2SITOR use no group separation.

I

QUICK REFERENCE

I How to set a Channel/GroupThe IC-M802 has up to 160 user-programmable, 242ITU SSB duplex, 72 ITU SSB simplex and 662 ITU

FSK duplex channels.

D Using the group and channel selectorsq Rotate [GRP] to select the desired group.

Available groups are shown in the list below.During user-programmable channel group use, thechannels change in 20-channel steps. See details onp. 8.Example; When starting the user-programmable Ch. 1.

1 21 41141 401 4-1 60125-11w Rotate [CH] to select the desired channel.

Available channels are shown in the list below.Pushing [ Y ]/[Z ] on the microphone also selects achannel.

[CH][GRP]

Channel No. Description Channel No. Description Channel No. Description

1 to 160 User Ch.* 1 1201 to 1241 12 MHz ITU duplex Ch. 22-1 to 22-9 22 MHz ITU simplex Ch.401 to 427 4 MHz ITU duplex Ch. 12-1 to 12-9 12 MHz ITU simplex Ch. 2501 to 2510 25 MHz ITU duplex Ch.4-1 to 4-9 4 MHz ITU simplex Ch. 1601 to 1656 16 MHz ITU duplex Ch. 25-1 to 25-9 25 MHz ITU simplex Ch.601 to 608 6 MHz ITU duplex Ch. 16-1 to 16-9 16 MHz ITU simplex Ch. C1-1 to C1-21 C1 channels6-1 to 6-9 6 MHz ITU simplex Ch. 1801 to 1815 18 MHz ITU duplex Ch. C2-1 to C2-31 C2 channels801 to 832 8 MHz ITU duplex Ch. 18-1 to 18-9 18 MHz ITU simplex Ch. 4001 to 25040 ITU FSK duplex Ch.* 2

8-1 to 8-9 8 MHz ITU simplex Ch. 2201 to 2253 22 MHz ITU duplex Ch.

D Using the keypad

When selecting an user-programmable channel Push the appropriate numeral keys to set the 1,

2 or 3-digit channel number, then push [ENT]Pushing [CE] clears input digits and retrieves thechannel.

Example; When selecting Ch. 1.Push [1 NB ] then push [ENT].

Example; When selecting Ch. 35.Push [3 SCAN ], [5 AGC ] then push [ENT].

Example; When selecting Ch. 128.Push [1 NB ], [2 SQL ], [8 Mid] then push [ENT].

When selecting an ITU duplex channel Push the appropriate numeral keys to set the 3,

4 or 5-digit channel number, then push [ENT]Pushing [CE] clears input digits and retrieves thechannel.

Example; When selecting Ch. 401.Push [4 SP ], [0 DIM ], [1 NB ] then push [ENT].

Example; When selecting Ch. 2505.Push [2 SQL ], [5 AGC ], [0 DIM ], [5 AGC ] then push[ENT].

When selecting an ITU simplex channel Push the appropriate numeral keys to set the 5

or 6-digit channel number, then push [ENT] Push [0 DIM ] 3 times to enter (dash). Pushing [CE] clears input digits and retrieves thechannel.

Example; When selecting Ch. 4-1.Push [4 SP ], [0 DIM ], [0 DIM ], [0 DIM ], [1 NB ] thenpush [ENT].

-After pushing [0DIM

] 3 times, appears.Example; When selecting Ch. 25-2.Push [2 SQL ], [5 AGC ], [0 DIM ], [0 DIM ], [0 DIM ],[2 SQL ] then push [ENT].-After pushing [0 DIM ] 3 times, appears.

Numeral keys [ENT][CE]


5/78

Q u

i c k R e

f e r e n c e

II

QUICK REFERENCE

I Audio output/squelch adjustmentD Audio output level Rotate [VOL] to adjust audio output level.

NOTE: Make sure that no and SQL indi-cators are displayed during audio level adjustment,otherwise, audio may not be output.When either or both indicators are displayed, per-form the following operations;-When is displayed, push [ F ] then [4 SP ].-When SQL is displayed, push [ F ] then [2 SQL ]. [VOL]

[2 SQL][4 SP ]

[F ]SP

SP

D Squelch function Push [ F ] then [2 SQL ] to turn the squelch function

ON and OFF.

SQL appears when the squelch function is ON.

SQ LL H

CH - - -GPS---La t 45 59 'NLon134 44 'E 16:23

J3E SIMP

[2 SQL ][F ]

Squelch level adjustment q Push [ F ] then [2 SQL ] to turn the squelch function

ON. Select the desired frequency/channel in advance, if de-sired.

w Push [ F ] then [MODE SET ] to enter quick setmode.

e Rotate [GRP] to select the S-SQL LEVEL item.r Rotate [CH] to adjust the squelch level.

Adjust the level within 1 100 range.

t Push [MODE SET ] to exit quick set mode.

ITEM SEL

[MODE SET ]

[2 SQL ]

[CH][GRP]

[F ]

Voice squelch function The voice squelch function detects voice componentsin the received signal and opens the squelch onlywhen voice components are included in the signal.q While pushing [MODE SET ] turn the power ON to

enter initial set mode.

w Rotate [GRP] to select the VOICE SQL item.e Rotate [CH] to select the voice squelch function

ON and OFF

r Turn the power OFF then ON again to exit initialset mode.

** * SE T MODE ** *

OF FON

ITEM SEL

[MODE SET ]

[2 SQL ]

[POWER][GRP]

[CH]


6/78

III

QUICK REFERENCE

I Basic voice transmission and receptionD Receiving a signalq Select the desired channel via [GRP] and [CH], or

keypad. Turn ON/OFF the squelch function or adjust thesquelch level as desired.

w When a signal is received, RX indicator appearsand audio is output from the connected speaker. Rotating [VOL] to adjust the audio output level at thismoment is recommended.

S-meter shows the received signal strength.e Use the following functions, if desired:

Noise blanker Push [ F ] then [1 NB ] to turn the noise blankerON and OFF. NB appears when the noise blanker is activated.See page 48 for the noise blanker level adjustment.

AGC (Automatic Gain Control) OFF function Push [ F ] then [5 AGC ] to turn the AGC OFFfunction ON and OFF. appears when the AGC-OFF function isactivated (deactivating AGC).

RF gain level Push [ F ], [6 RF -G ] to enter the RF gain adjust-ment mode, then rotate [CH] to adjust the gain.Adjust the gain within 0 (low sensitivity) to 9 (maxi-mum sensitivity) range.

Push [MODE SET ] to exit the adjustment mode.Clarity

Push [ F ], [RX CLAR ] to switch the clarity func-tion ON and OFF, then rotate [CH] for criticaltuning.

[5 AGC ]

[1 NB]

[F ] [RX CLAR ]

[6 RF-G ]

AGC

D Transmitting in voiceq Select the desired channel via [GRP] and [CH], or

keypad.

w Push [ F ], then push and hold [TX TXF ] for a whileto monitor the transmit frequency of the selectedchannel. The transmit frequency is displayed and TX blinks. When the channel is busy, wait until it becomes clear,or change the channel.

e Push [ F ] then one of [7 Lo], [8 Mid] or [9 Hi] to se-lect low, middle or high output power, respectively.

r When the optional AT-140 is connected, push[TUNE THRU ] to start manual tuning. TUNE appears when the antenna is tuned. TUNE blinks when a tuning error has occurred. Automatic tuning function is also available.

t Push and hold [PTT] on the microphone to trans-mit. TX appears. If SWR appears during transmit, check your antennasystem.

y Speak into the microphone at your normal voicelevel.

u Release [PTT] to return to receive. TX disappears.

[TUNE THRU]

[8 Mid]

[7 Lo]

[F ]

[9 Hi]

[TX TXF][GRP] [CH] [ F ]


7/78

Q u

i c k R e

f e r e n c e

IV

QUICK REFERENCE

I Receiving a DSC For waiting for a DSC call, such as an individual,

group or all ships call on the desired frequencies,

push [DSC] to enter DSC watching mode. Monitoring the frequencies, 2187.5, 4207.5, 6312.0,8414.5, 12577.0 and 16084.5 kHz, for distress, ur-gency, etc., no operation is necessary with the trans-ceiver. These frequencies are monitored at all times.

[DSC]

D Simple distress call Lift up the distress switch cover, then push and

hold [DISTRESS] for 5 sec. After 5 sec., a distress call is sent.

[DISTRESS]

I Transmitting a distress call


8/78

V

QUICK REFERENCE

D Regular distress callq Push [DSC] to enter DSC watch mode.

w Push [MODE SET ] to enter DSC menu.

e Rotate [CH] to select Distress then push[ENT]

r Rotate [CH] to select the desired nature then push[ENT].

t Verify your position and the UTC time, then push[ENT]. When no NMEA0183 ver. 3.01 data is applied to [GPS],your position and UTC time should be input in this step.-Use the keypad and [CH] when changing your posi-tion or the time.

-Move the cursor with [CH] rotation.- [3 SCAN ], [6 RF -G ], [7 Lo] and [9 Hi] is used for theEast, North, South and West selection.

y Rotate [CH] to select the DSC calling frequencies,then push [ENT]. After pushing [ENT], return to DSC menu as shown instep e .

u Lift up the distress switch cover, then push andhold [DISTRESS] for 5 sec.

[DISTRESS]

******* Dist ress *******--- - - - - - Attempt - - - - - - -

Single ;s ix f requencySingle ; 2187.5kHzSingle ; 4207.5kHzSingle ; 6312.0kHzSingle ; 8414.5kHzSingle ;12577.0kHzSingle ;16804.5kHz

OKSE L

******* Dist ress *******-- - Posi t ion & t ime - - - -

Lat i tudeLongi tude

UT C

34 34 'N13 5 34 'E 12:34

OKNull

******* Distress *******--- - - - - - Nature - - - - - - - -

UndesignatedFire ,Explos ionFloodingCol l is ionGroundingCapsiz ingSinkingDisable adr i f tAbandoning shipPiracy at tackMa n overboardEPIRB emiss ion

OKSE L

******* DS C MENU *******--- - - - - - Select - - - - - - - -

Posi t ionIndividualGroupAl l shipsPosi t ion RE QDist ressTestRX memoryTX memorySe t upExi t

OKSE L

[MODE SET ]

[ENT][CH]

[DSC]


9/78

1

1

OPERATING RULES AND GUIDELINES

1

Q u

i c k R e

f e r e n c eBefore transmitting, monitor the channel you wish to

use so as to avoid interrupting transmissions al-ready in progress.

CALL PROCEDURECalls must be properly identified and the time limitmust be respected.

q Give your call sign each time you call another shipor coast guard station. If you have no call sign,identify the station by giving your ship name and thename of the licensee.

w Give your call sign at the end of each transmissionthat lasts more than 3 min.

e You must break and give your call sign at least once

every 15 min. during long ship-to-shore calls.r Keep your unanswered calls short, less than

30 sec. Do not repeat a call for 2 min.

t Unnecessary transmissions are not allowed.

PRIORITIES

q Read all rules and regulations pertaining to priori-ties and keep an up-to-date copy handy. Safety anddistress calls take priority over all others.

w False or fraudulent distress signals are prohibitedand punishable by law.

PRIVACY

q Information overheard but not intended for you, can-not lawfully be used in any way.

w Indecent or profane language is prohibited.

LOGSq All distress, emergency and safety calls must be

recorded in complete details. Log data activity isusually recorded in 24 hour time. Universal TimeCoordinated (UTC) is frequently used.

w Adjustments, repairs, channel frequency changesand authorized modi cations affecting electrical op-eration of the equipment must be kept in the main-tenance log; entries must be signed by the autho-rized licensed technician performing or supervisingthe work.

RADIO LICENSES

(1) SHIP STATION LICENSEYou must have a current radio station license beforeusing the transceiver. It is unlawful to operate a shipstation which is not licensed.

Inquire through your dealer or the appropriate govern-ment agency for a Ship-Radiotelephone license appli-cation. This government-issued license states the callsign which is your craft s identification for radio pur-

poses.(2) OPERATOR S LICENSEA Restricted Radiotelephone Operator Permit is the li-cense most often held by small ship radio operatorswhen a radio is not required for safety purposes.

The Restricted Radiotelephone Operator Permit mustbe posted or kept with the operator. Only a licensedradio operator may operate the transceiver.

However, non-licensed individuals may talk over atransceiver if a licensed operator starts, supervises,

and ends the call and makes the necessary log en-tries.

Keep a copy of the current government rules and reg-ulation handy.


10/78

2

2

PANEL DESCRIPTION

I Front panel Controller

q DISTRESS SWITCH [DISTRESS] (p. 18)Push for 5 sec. (approx.) to make a distress call.

w DSC SWITCH [DSC]

Switches DSC watch mode and voice/e-mail com-munication mode when pushed.

e CANCEL/CALL SWITCH [CANCEL/CALL] Cancels a distress or DSC repeat call. (p. 20) Push for 1 sec. to start calling after DSC contents

are setup.

r HEADPHONE JACK [ ]Accepts headphones. Output power: 5 mW with a 16 load (stereo).

t MICROPHONE CONNECTOR [MIC]

Accepts the supplied or optional microphone. See p. 66 for appropriate microphones. See p. 61 for microphone connector information.

y GROUP SELECTOR [GRP] Selects groups in 20 channel steps and ITU ma-

rine channel groups. (p. 8) Selects items during quick/initial set mode, etc.

u CHANNEL SELECTOR [CH] Selects an operating channel within the selected

channel group such as ITU channels. (p. 8)User channels can be selected from 1 to 160 (max.)in sequence regardless of the channel group.

Changes setting or value of the selected itemduring quick/initial set mode, etc.

i RX/CLARITY SWITCH [RX CLAR ] After pushing [ F ], turns the clarity function ON

and OFF. (p. 12) [CH] is used for clarity control.

During DSC watch mode, enters RX memory se-lect screen. (p. 38) [CH] is used for distress and other call selection.

o POWER SWITCH [POWER] Push to turn the power ON. Push for 1 sec. to turn the power OFF.

! 0TX/TRANSMIT FREQUENCY SWITCH [TX TXF ] After pushing [ F ], displays the transmit fre-

quency, and opens the squelch. Checks and mon-itors the transmit frequency while holding. (p. 10)

During DSC watch mode, enters TX memory se-lect screen. (p. 43) [CH] is used for memory selection.

! 1VOLUME CONTROL [VOL]Adjusts the audio output level. Audio does not come from the speaker when:

- The speaker switch is turned ON.- The squelch function is turned ON and no signal is

being received.- During DSC watch mode.

DISTRESSq

w

e

r

t

y u i o !0 !1

!2

!3

!4!5!6!7Function display (pgs. 6, 7)


11/78

3

2PANEL DESCRIPTION

2

!2 FREQUENCY/CHANNEL SWITCH [FREQ/CH] Selects indication type: (p. 8)

When channel comment indication is ON;switches channel comment indication ON and

OFF.When channel comment indication is OFF;switches transmit frequency indication ON andOFF.

After pushing [ F ], enters channel name pro-gramming mode, when channel comment indica-tion is ON. (p. 14)

! 3KEYPAD Inputs numeral 1 for channel number

input, etc. Inputs 1, Q, Z, q, z or space for

channel comment input. After pushing [ F ], turns the noise

blanker function ON and OFF. (p. 11)

Inputs numeral 2 for channel numberinput, etc.

Inputs 2, A, B, C a, b or c forchannel comment input.

After pushing [ F ], turns the squelchfunction ON and OFF. (p. 11)


Inputs 3, D, E, F, d, e or f for

channel comment input. After pushing [ F ], starts and stops the

scan function. (p. 9)


Inputs 4, G, H, I, g, h or i forchannel comment input.

After pushing [ F ], turns the speaker out-put ON and OFF. (p. 10)


Inputs 5, J, K, L, j, k or l forchannel comment input.

After pushing [ F ], turns the AGC OFFfunction ON and OFF. (p. 11)


Inputs 6, M, N, O, m, n or o forchannel comment input.

After pushing [ F ], enters the RF gain adjustment mode. (p. 11)


Inputs 7, P, R, S, p, r or s forchannel comment input.

After pushing [ F ], selects low transmitoutput power. (p. 10)


Inputs 8, T, U, V, t, u or v forchannel comment input.

After pushing [ F ], selects middle trans-mit output power. (p. 10)


Inputs 9, W, X, Y, w, x or y forchannel comment input.

After pushing [ F ], selects high transmitoutput power. (p. 10)


Inputs 0 and symbols ( - / . , ( ) *+ < = > @ ) for channel comment input.

After pushing [ F ], selects LCD backlightbrightness.

Fixes input of channel number and chan-nel comment, etc.

When pushed for 1 sec., stores pro-grammed frequency, operating mode andmemory comment into a channel.

Clears entered digits and retrieves theprevious frequency, channel or channelnames during setting.

! 4FUNCTION SWITCH [ F ]After pushing, activates the secondary functions. appears when a secondary function can be ac-cessed.

! 5TUNE/THROUGH SWITCH [TUNE THRU ] Starts tuning when an optional antenna tuner is

connected. TUNE appears when tuned. When the tuner cannot tune the antenna, the tuningcircuit is bypassed automatically after 15 sec.

After pushing [ F ], bypasses the connected an-tenna tuner. (p. 12) THRU appears instead of TUNE indication. This operation available for AT-140 and AH-3 only.

! 6MODE/SET SWITCH [MODE SET ] Push to select an operating mode.

J3E (USB), H3E (AM), LSB, J2B (AFSK), F1B (FSK),and A1A (CW) modes are available, depending onversion or countries.

After pushing [ F ], enters quick set mode. (p. 48) Enters DSC menu during DSC watch mode.

! 7E-MAIL SWITCH [e-mail] (p. 47)Switches between e-mail operation mode and voiceoperation mode when pushed.


12/78

I Front panel Main unit

q GPS CONNECTOR [GPS] (pgs. 53, 62)Input position and UTC data (NMEA0183 ver. 3.01format), such as from a GPS receiver, etc., for set-ting your positioning and time data automaticallywithout manual input for DSC operation.

w REMOTE CONNECTOR [REMOTE] (pgs. 53, 62)Connects to a PC via an RS-232C cable (D-sub 9-pin) for remote control in the NMEA or RS-232C for-mat.

e MODEM CONNECTOR [AF/MOD] (pgs. 53, 62)Connects to an e-mail modem, NBDP (NarrowBand Direct Printing) or FAX system via an RS-232C cable (D-sub 9-pin).

r ACCESSORY CONNECTOR [ACC](pgs. 12, 13, 61)Connects a CW keyer or an FSK terminal unit, etc.

t CONTROLLER CONNECTOR [CONTROLLER]

(p. 53)Connects the supplied remote controller.

y SPEAKER JACK [SP] (p. 53)Connects the supplied external speaker, SP-24.

4

2 PANEL DESCRIPTION

q w e

rty


13/78

5

2PANEL DESCRIPTION

2

I Rear panel Main unit

q TUNER CONTROL SOCKET (pgs. 54, 56, 61)Connects a control cable to an optional antennatuner.A female connector kit is supplied for external an-tenna tuner connection.

w GROUND TERMINAL

IMPORTANT! Connects a ship s (or vehicle s)ground. See pages 55 and 63 65 for details.

e ANTENNA CONNECTOR 1 (pgs. 54, 56)Connects a 50 HF band antenna via a 50 matched coaxial cable with a PL-259 plug for bothtransmit and receive operation.

r ANTENNA CONNECTOR 2 (pgs. 54, 56)Connects a 50 HF band antenna via a 50 matched coaxial cable with a PL-259 plug for DSCreceiver.

t DC POWER SOCKET (p. 54, 61)Accepts 13.6 V DC through the supplied DC power

cable.

q w e r t

I Microphone (HM-135)q PTT SWITCH [PTT]

Push and hold to transmit; release to receive.

w UP/DOWN SWITCHES [ ]/[ ]Push either switch to change the operating channel,frequency, etc.

e USER PROGRAMMABLE SWITCH [P]Push to activate or deactivate a function, selectedin initial set mode (p. 51).

Microphone

w

q

e

For detailed ANTENNA AND GROUNDING CON-SIDERATIONS, see pages 63 to 65.


14/78

6

2 PANEL DESCRIPTION

I LCD screenThe IC-M802 has 2 indication types, one is channelname indication and the other is frequency indication.

These indication types can be switched with a push ofa button, depending on set mode s setting. Seepages 8 and 50 for display type settings.

N B SQ LL H

CH

C L A R0

WIDE

SP

AGC - - - G P S - - -L a t 45 5 9 ' NLon134 44 'E 16:23

RX

TX

T X

T UN E J 3E SIMP

Exi t

S P

34 34 .000N134 34 .000E 1 2 : 3 4

R X

12.345 .5 J2B

WIDE

GP S

NB S QLCH

CLAR 0SPAGC

U TC 1 6 : 2 3

RX T UNE J3E SIMP

Channel name indication

Frequency indication

DSC watch mode indication

q

w e r t y

u

i

o

!0

!1!2

!3!4!5

!6

q

w e r t y

u

io

!0

!1

!2!3!4!5

!6

q

e

t

i!0

!8

!9

!6

!7


15/78

7

2PANEL DESCRIPTION

2

q RECEIVE INDICATORRX appears when signals are received or thesquelch is open.

w TUNE INDICATORTUNE blinks while tuning, if an optional externalantenna tuner is connected. (p. 10) TUNE appears after tuning is completed with AT-140,AT-130/E and AH-3.

THRU appears when the tuner through function is ac-tivated.(This function is available only when connecting AT-140or AH-3.)

SWR appears when the antenna SWR worsens duringtransmit, depending on the transmit output power. If itappears, check your antenna system.

e OPERATING MODE INDICATORShows the selected operating mode. J3E , USB , H3E , AM , LSB , J2B , AFS ,F1B FSK , A1A or CW appears depending on op-erating mode and setting.

r SIMPLEX/DUPLEX INDICATORSIMP appears when a simplex channel is se-lected.DUP appears when a duplex channel is selected.

t FUNCTION INDICATOR appears when a secondary function can be ac-cessed.

y IF FILTER WIDTH INDICATORShows the selected IF lter passband width duringe-mail operation mode.

u CLARITY INDICATOR (p. 12)CLAR appears when the clarity function is acti-vated and shows shifting frequency in Hz.

i SPEAKER OFF INDICATOR appears when the speaker output is turnedOFF.

o AGC OFF INDICATOR (p. 11) appears when the AGC OFF function isturned ON.

! 0POSITION/UTC TIME INDICATOR (p. 16)Shows position and/or UTC (or local) time. Whenan NMEA0183 ver. 3.01 data is applied to [GPS],the indication is up dated automatically. When no NMEA data is applied, the position and UTCtime must be set in advance.

GPS appears when an NMEA0183 ver. 3.01 data isapplied to [GPS], MNL appears when the position ismanually set.

UTC appears when the offset time has not been pro-grammed. (No UTC indication when offset time is pro-grammed and shows local time.)

!1 CHANNEL NUMBER INDICATIONShows the selected channel number.

! 2S/RF INDICATORShows relative transmit output power levels duringtransmit and receiving signal strength during re-ceive.

! 3NOISE BLANKER INDICATOR (p. 11)NB appears when the noise blanker function is ac-tivated.

! 4SQUELCH INDICATOR (p. 11)SQL appears when the squelch is ON.

! 5TRANSMIT INDICATOR TX appears during transmit. TX blinks while monitoring a transmit frequency.

(p. 10)

! 6CHANNEL NAME/RECEIVE FREQUENCYREADOUT Shows the programmed channel names. Shows receive frequency when no channel name

is programmed, or during frequency indication. During DSC watch mode, displays DSC WATCH.

! 7TRANSMIT FREQUENCY READOUTShows transmit frequency.

! 8OPERATING GUIDE INDICATIONDuring DSC watch mode operation, shows severaltypes of guidance, according to the selected condi-tion.

! 9SCANNING FREQUENCY READOUTDuring DSC watch mode operation, shows the pro-grammed scan frequency. Decimal points blink.

AGC

SP


16/78

3

8

SELECTING A CHANNEL/FREQUENCY

CHANNEL GROUPS *1[GRP] changes in 20 channels steps. * 2SITOR use no group separation.

I Selecting a channelThe transceiver has 160 user channels and ITU chan-nels. However, the number of user channels can be

optionally restricted.

D Display selection

NOTE: Channel name (alphanumeric) may not ap-pear during frequency indication depending on ini-tial set mode setting. (p. 50)

FREQUENCY indication CHANNEL indication

16 :23

RX J3E S IM P

CH L H

CH - - -GPS- - -La t 45 59 'NLon134 44 'E 16 :23

RX J 3E S IMP

D Using the channel selectorThe transceiver has two large controls for group se-lection and channel selection. The [GRP] changeschannels in 20 channel increments and selects ITUchannel groups; and the [CH] selects each channel.

q Rotate [GRP] to select the desired channel groupas shown at right and/or below.

w Rotate [CH] to select the desired channel.

[EXAMPLE]: Selection with the [GRP]

I T U S S B c

h a n n e

l s

CH - - -GPS- - -La t 45 59 'NLon134 44 'E 16 :23

RX J3E SIMP

L H

CH - - -GPS- - -La t 45 59 'NLon134 44 'E 16 :23

RX J3E SIMP

L H

CH - - -GPS- - -La t 45 59 'NLon134 44 'E 16 :23

RX J3E SIMP

L H

CH - - -GPS- - -La t 45 59 'NLon134 44 'E 16 :23

RX J3E SIMP

L H

CH - - -GPS- - -La t 45 59 'NLon134 44 'E 16 :23

RX J3E SIMP

L H

CH - - -GPS- - -Lat 45 59 'NLon134 44 'E 16 :23

RX J3E DU P

L H

CH - - -GPS- - -Lat 45 59 'NLon134 44 'E 16 :23

RX J3E SIMP

L H

CH - - -GPS- - -Lat 45 59 'NLon134 44 'E 16 :23

RX J3E DUP

L H

CH - - -GPS- - -Lat 45 59 'NLon134 44 'E 16 :23

RX J3E SIMP

L H

[CH][GRP]

Channel No. Description Channel No. Description Channel No. Description

1 to 160 User Ch.* 1 1201 to 1241 12 MHz ITU duplex Ch. 22-1 to 22-9 22 MHz ITU simplex Ch.401 to 427 4 MHz ITU duplex Ch. 12-1 to 12-9 12 MHz ITU simplex Ch. 2501 to 2510 25 MHz ITU duplex Ch.

4-1 to 4-9 4 MHz ITU simplex Ch. 1601 to 1656 16 MHz ITU duplex Ch. 25-1 to 25-9 25 MHz ITU simplex Ch.601 to 608 6 MHz ITU duplex Ch. 16-1 to 16-9 16 MHz ITU simplex Ch. C1-1 to C1-21 C1 channels6-1 to 6-9 6 MHz ITU simplex Ch. 1801 to 1815 18 MHz ITU duplex Ch. C2-1 to C2-31 C2 channels801 to 832 8 MHz ITU duplex Ch. 18-1 to 18-9 18 MHz ITU simplex Ch. 4001 to 25040 ITU FSK duplex Ch.* 2

8-1 to 8-9 8 MHz ITU simplex Ch. 2201 to 2253 22 MHz ITU duplex Ch.


17/78

3

3

9

SELECTING A CHANNEL/FREQUENCY

D Using the keypadDirect channel selection via the keypad is availablefor quick channel selection.q Enter the desired channel number via the keypad.

Pushing [CE] clears input digits and retrieves the chan-nel.

A user channel is selected when channel 1 160 isinput (max. number may be optionally restricted).

An ITU SSB channel is selected when channel num-bers higher than 401 are input.

When selecting an ITU simplex channel, push [0 DIM ]three times to input (dash). (e.g. When selecting the channel 4-1; push [4 SP ], [0 DIM ], [0 DIM ], [0 DIM ] then [1 NB ].)

w Push [ENT] to select the channel.

[EXAMPLE]: Selecting channel 158

L H

CH - - -GPS---La t 45 59 'NLon134 44 'E 16:23

RX J3E

CH - - -GPS---La t 45 59 'NLon134 44 'E 16:23

RX J3E

L H

CH - - -GPS---La t 45 59 'NLon134 44 'E 16:23

RX J3E

L H

CH - - -GPS---La t 45 59 'N

RX J3E SIMP

D Using scan functionThe transceiver has automatic channel or frequencychange capability (scan function). There are 3 typesof scan functions available to suit your needs.

Channel scan and channel resume scan increasechannels within a 20 channel range, such as Ch 1 toCh 20, Ch 141 to Ch 160, etc., in user channels; orall channels in the group of ITU channels.Programmed scan scans frequencies within the fre-quency range between user channels 159 and 160.Scan type selection is available in initial set mode.

See p. 50 for the selection.SCAN OPERATIONq Rotate [GRP] and [CH], or use the keypad to se-

lect your desired channel group. This operation is not necessary for programmed scan.

w Push [ F ] then [2 SQL ] to turn OFF the squelchfunction, if programmed scan is selected.

e Push [ F ] then [3 SCAN ] to start the scan.r To stop the scan, repeat step e again.

[CH] rotation or pushing some other switches alsostops the scan.

Channel scan/Channel resume scan

Ch 1

Ch 2 Ch 3

Ch 4

Ch 20

When resume OFF;scan does not pause even

if a signal is received.When resume ON;scan pauses for 10 sec.,then resumes, or resumesafter 2 sec. from when thesignal disappears.

Programmed scan

Ch 159 Ch 160Scans the frequency rangebetween the programmedfrequencies on channels159 and 160.Scans fast when squelch isclosed and slowly whensquelch is open.


18/78

4

10

RECEIVE AND TRANSMIT

I Basic voice transmit and receiveq Check the following in advance.

Microphone is connected.

No SQL indication. If SQL appears, push [ F ] then [2 SQL ] to turn thesquelch OFF.

No indication. If appears, push [ F ] then [4 SP ] to activatethe speaker.

The clarity function is not activated. If the clarity function is activated, push [ F ] then[RX CLAR ] to turn the function OFF.

w Rotate [GRP] and [CH] to select the desired chan-nel to be received.

When receiving a signal, the S-meter shows the signalstrength.e Adjust [VOL] to the desired audio level when re-

ceiving a signal.r Push [MODE SET ] to select the desired operating

mode.t Push [TUNE THRU ] to tune the antenna tuner, if con-

nected. Skip this operation when the AUTO TUNE is set to ONin initial set mode (p. 50).

y To transmit on the channel, push and hold the PTTswitch on the microphone. TUNE blinks for 1 to 2 sec. for the first transmission

on a channel when the automatic tuning function is acti-vated.

u Speak into the microphone at your normal voicelevel. The RF meter shows the output power according to yourvoice level.

If SWR appears, check your antenna system.i Release the PTT switch to return to receive.

[RX CLAR ]Microphoneconnector

[4 SP ] [2 SQL ]

[F ]

SPSP

I Functions for transmit

D Transmit frequency check When DUP appears in the display such as for aship-to-ship channel, the transmit frequency differsfrom the receive frequency.

In such cases, the transmit frequency should be mon-itored before transmitting to prevent interference toother stations.

Push [ F ] then push and hold [TX TXF ] to monitorthe transmit frequency. TX blinks and the display shows the transmit frequency.

[TX TXF][F ]

D Transmit power selectionThe transceiver has 3 selectable power output levels.High power allows longer distance communicationsand low power reduces power consumption.

q Push [ F ] rst. appears.

w Push one of [7 Lo ], [8 Mid ] or [9 Hi ] to select low,middle or high output power levels, respectively. The display shows the selected output power level forapprox. 2 sec., then returns to the previous indication. [F ]

[9 Hi][8 Mid][7 Lo]


19/78

11

4RECEIVE AND TRANSMIT

4

I Functions for receiveD Squelch functionThe squelch function detects signals with voice com-ponents and squelches (mutes) unwanted signalssuch as unmodulated beat signals. This providesquiet stand-by.

When you need to receive weak signals, the squelchshould be turned OFF. Push [ F ] then [2 SQL ] to switch the function ON

and OFF. See page 48 for the squelch level adjustment. SQL appears when the squelch function is turned ON.

[2 SQL ][F ]

D Noise blankerThe noise blanker function reduces pulse type noisesuch as that coming from engine ignitions, etc.

The noise blanker may distort reception of strong sig-nals. In such cases, the noise blanker should beturned OFF.

Push [ F ] then [1 NB ] to switch the function ON andOFF. See page 48 for the noise blanker level adjustment. NB appears when the NB function is turned ON.

[1 NB][F ]

D AGC OFF functionThe receive gain is automatically adjusted accordingto received signal strength with the AGC (AutomaticGain Control) function to prevent distortion fromstrong signals and to obtain a constant output level.

When receiving weak signals with adjacent strongsignals or noise, the AGC function may reduce thesensitivity. In this situation, the AGC function shouldbe deactivated.

Push [ F ] then [5 AGC ] to switch the function ONand OFF.

appears when the AGC function is turned OFF.AGC

[5 AGC ][F ]

D RF gain settingThe receiver gain can be reduced with the RF gainsetting. This may help to remove undesired weak sig-nals while monitoring strong signals.

Usually, the AGC function reduces the RF gain ac-cording to the receive signal strength and these weaksignals are removed. However, during no signal re-ception, these weak signals may not be heard.

In such cases, the RF gain may be useful for setting aminimum level at which to hear signals.

q Push [ F ] then [6 RF -G ] to select the RF gain setmode, as shown below.

w Rotate [CH] to set the desired minimum cuttinglevel. 0 (low sensitivity) to 9 (max. sensitivity) are available. S-meter shows the minimum permitted level.

e Push any key to exit the RF gain set mode.


20/78

D Clarity controlVoice signals received from other stations may be dif -cult to receive. This may sometimes happen if a sta-tion is transmitting slightly off frequency. In such cases,you can compensate by using the clarity control.

q Push [ F ] then [RX CLAR ] to switch the function ONand OFF. CLAR and shifting value with direction appear.

w Rotate [CH] to improve the audio readability. Adjustable between 150 Hz in 10 Hz steps.

[RX CLAR ][CH] [F ]

I Functions for receive (continued)

I CW operation

12

4 RECEIVE AND TRANSMIT

The transceiver has the following CW keying featuresselectable in set mode as described on p. 51. Full break-in (receiving is possible while transmitting) Semi break-in (automatic transmission with keying) OFF (manual transmission with microphone s [PTT], or

grounding the SEND line of [ACC] connector isnecessary before keying)

q Connect a CW keyer or an external electronickeyer to the [ACC] socket as shown at right.

w Select the desired channel to operate CW mode.e If the selected channel is not in A1A mode, push

[MODE SET ] several times to select A1A.r Operate the CW keyer to transmit a CW signal.

CW key connection

1

2

345

678

To pin 2 P T T *

*manual transmission switch for break-inOFF setting.

To pin 1

To pin 3

D Tuner through functionIn the combination with IC-M802 and optional AT-140

(or AH-3), the tuner through function can be used.By bypassing the tuner unit, the receiver gain in par-ticular frequency band may be improved dependingon your antenna element length.

While TUNE is displayed, push [ F ] then[TUNE THRU ] to tuner through function ON. THRU appears instead of TUNE indicator. Push [TUNE THRU ] to turn the function OFF.

[TUNE THRU] [F ]


21/78

13

4RECEIVE AND TRANSMIT

4

I FSK operationThe transceiver has FSK and J2B modes for FSK op-eration use F1B when using the built-in oscillator;

use J2B when using an AFSK terminal unit.q Connect an FSK terminal unit to the [ACC] socket

as shown at right.w Select the desired channel to operate FSK mode.

FSK ITU channel group, Ch 4001 to Ch 25040, are onlyavailable when SITOR CH setting is set to ON. (p. 49)

e Push [MODE SET ] several times to select F1B or J2B.r Operate the FSK terminal unit.

NOTE: FSK tone, shift frequency and FSK polarity can

be adjusted in initial set mode (p. 51) Some transceivers may operate 1.7 kHz higher

than the IC-M802 s J2B mode even when thesame displayed frequencies are in use.

FSK terminal unit connection

1

2

345

678

To pin 1To pin 3

FSK keying

AF input

FSK terminal unit

AF ground

Tx/Rx controlGround

To pins 2, 5


22/78

5

14

CHANNEL NAME PROGRAMMING

D Programmingq Select the desired channel to be programmed.w Push [FREQ/CH] to select channel indication

mode, if desired.e Push [ F ] then [FREQ/CH].

The 1st character for the channel names blinks.

r Rotate [CH] selector to select the character forchannel names. See the table below for available characters.

t Push the keypad several times to enter that char-acter.

y Repeat steps r and t to enter the channel name.u Push [ENT] to program the channel name.

CH - - -GPS---La t 45 59 'NLon134 44 'E 16:23

RX J3E DU P

L H

CH - - -GPS---La t 45 59 'NLon134 44 'E 16:23

RX J3E DUP

L H

CH - - -GPS---La t 45 59 'NLon134 44 'E 16:23

RX J3E DU P

L H

Up to 8-character channel names can be assigned foreach user and ITU channel. This may be helpful for in-dicating the frequency usage, ship name, etc.

NOTE: The display type must be set to CH-NAME to display/program the channel names in ini-tial set mode. (p. 50).

Available characters

(space)

KEY CHARACTERS KEY CHARACTERS


23/78

6

15

DSC PREPARATION

5

6

I MMSI code programmingThe 9-digit MMSI (Maritime Mobile Service Identity:DSC self ID) code can be programmed.

This operation is not necessary when the MMSIcode has been programmed by your dealer. How-

ever, the code re-programming can be performed 2times only. This code is displayed when the power isturned ON.

D Programming

q While pushing [ F ] and [DSC], push [POWER] toturn the power ON.

w Push [DSC] to select DSC watch mode.e Push [MODE SET ].

DSC menu is selected as follows.r Rotate [CH] to select Set up , then push [ENT].

t Rotate [CH] to select MMSI Code , then push[ENT].

y Enter the speci ed 9-digit MMSI code via the key-pad. Make sure the correct code is entered. Rotate [CH] to move the cursor.

u Push [ENT] to program the code. After pushing [ENT], return to the display as describedin step t .

i Push [MODE SET ] to exit the DSC menu.

RX

J3 EGP S

12.345.0

Exi t

SPLa t 34 34 'NLon135 34 'E 12:34

******** Se t up ********--- - - - MMSI check - - - - - -

ID : 1 2 3 4 5 6 7 8 9

Cancel OK

******** Se t up ********--- - - - MMSI check - - - - - -

ID : ________

Cancel OK

******** Se t up ********--- - - - - - Select - - - - - - - -

Address IDGroup IDCal l f requencyTraff ic f requencyScan f rqeuencyMMSI check

OKSE L

******* DS C MENU *******--- - - - - - Select - - - - - - - -

Posi t ionRX memorySe t upExi t

OKSE L

[MODE SET ][ENT][DSC]

[F ][CH] [POWER]


24/78

16

6 DSC PREPARATION

I Position and time programming

q While pushing and holding [MODE SET ] push[POWER] to enter initial set mode. Turn the power OFF in advance.

w Rotate [GRP] to select the GPS DISPLAY thenrotate [CH] to select the desired position indicationtype from simple and detail.

e Rotate [GRP] to select the OFFSET TIME thenrotate [CH] to set the time difference between localand the UTC times within 12 to +12 hours in10 minute steps.

r Turn the power OFF once, then ON again to exitquick set mode.

When a position and the UTC time data (NMEA0183 ver. 3.01 format) is applied to [GPS],the following steps are not necessary.

t Push [DSC] to select DSC watch mode.y Push [MODE SET ] to enter the DSC menu.

DSC menu is displayed as below.u Rotate [CH] to select Position , then push

[ENT].

i Enter your position and the UTC time via the key-pad, then push [ENT] Push [3 SCAN ] for the East, [9 H i] for the West, [6 RF -G ]for the North and [7 L o] for the South setting.

Degrees and minutes digits can only be entered evenwhen DETAIL is selected for the position indicationin step w the seconds digits show 0 only.

Rotate [CH] to move the cursor.

o Push [ENT] to program the position and time. Return to the DSC MENU indication as in step u .

!0 Push [MODE SET ] to exit the DSC menu.

Rotate [CH] to select Exit then push [ENT] alsoexits set mode. MNL appears instead of GPS .

******* Posi t ion *******-- - Posi t ion & t ime - - - -


UT C

34 34 'N13 5 34 'E 12:34

OKNull

******* DS C MENU *******--- - - - - - Select - - - - - - - -

Posi t ionIndividualGroupAl l shipsPosi t ion RE QDist ress

OKSE L

** * SE T MODE ** *

ITEM SEL

** * SE T MODE ** *

SIMPLEDETAIL

ITEM SEL

[POWER][MODE SET ]

When no position and the UTC (Universal Time Coor-dinated) time data in NMEA0183 ver. 3.01 format, such

as from a GPS receiver, etc., is applied to [GPS] con-nector, your position and the UTC time should be inputfor DSC operation.

IMPORTANT! The manually programmed position and the UTC

time settings will be cleared once the power isturned OFF. They are never renewed during thevoyage when the position is set manually.

RX

J3 EMN L

12.345.0

Exi t

SP 34 34.000N13 5 34.000E 12:34

RX

J3 EMN L

12.345.0

Exi t

SPLa t 34 34 'NLon135 34 'E 12:34

Simple position indication Detail position indication


25/78

6

7

7

17

CALL PROCEDURE

I Distress callA distress call should be transmitted if in the opinion ofthe Master, the ship or person is in distress and re-

quires immediate assistance.A distress call should include the ship s position andtime. They are included automatically when their datain NMEA0183 ver. 3.01 format is applied to [GPS] con-nector. When no data is applied, input them, if possible.

A distress call some times called as a MAYDAY call.

D Distress call operation outline

NEVER USE THE DISTRESS CALL WHEN YOUR SHIP IS NOT IN AN EMERGENCY. DISTRESS

CALLS CAN BE USED ONLY WHEN IMMEDIATE HELP IS NEEDED.

RX

J3 EGP S

12.345.0

Exi t

SPLa t 34 34 'NLon135 34 'E 12:34

******* DS C MENU *******--- - - - - - Select - - - - - - - -


OKSE L

******* Distress *******--- - - - - - Nature - - - - - - - -

UndesignatedFire ,Explos ionFloodingCol l is ion

GroundingCapsiz ingSinkingDisable adr i f tAbandoning shipPiracy at tackMa n overboardEPIRB emiss ion

OKSE L



UT C

34 34 'N13 5 34 'E 12:34

OKNull



OKSE L

DSC menu Distress nature selection Position & UTC time setting

Frequency selection

Push and hold [DISTRESS] for 5 sec.

Push and hold[DISTRESS]for 5 sec.

Simple distress call

Regular distress call


26/78


27/78

19

7CALL PROCEDURE

7

D Regular distress callTransmit a distress call after selecting Distress in the DSC menu.

NEVER USE THE DISTRESS CALL WHEN YOUR SHIP IS NOT IN AN EMERGENCY. DISTRESS CALLS CAN BE USED ONLY WHEN IMMEDIATE HELP IS NEEDED.

q Push [DSC] to select DSC watch mode.w Push [MODE set] to select the DSC menu.

e Rotate [CH] to select Distress , then push[ENT].

r Rotate [CH] to select the desired nature then push[ENT].

t Verify the position and UTC time data, then push[ENT]. When no position and time data is applied to [GPS],your position and UTC time should be input in this step.

y Rotate [CH] to select the desired distress fre-quency, then push [ENT]. After pushing [ENT], return to the DSC menu as shownin step q .

u Lift up the distress switch cover, push [DISTRESS]for 5 sec. to transmit the distress call. The distress call is transmitted on the emergency fre-quency selected in step y .

i After transmitting the call, the transceiver is set tothe phone emergency frequency automatically. The DSC receiver circuit is still working to receive anacknowledgement call on the previous frequency.

The distress call transmission and acknowledgementreception are performed on the all distress frequencies(2187.5, 4207.5, 6312.0, 8414.5, 12577.0 and16804.5 kHz) in sequence when Single;sixfrequency is selected in step y .

o When receiving an acknowledgement, push [CAN-CEL/CALL] to stop the alarm then reply to the con-nected station via the transceiver s microphone. The acknowledgement is memorized into the RX mem-

ory channel. (p. 38)

RXJ3 E

< Wait fo r AC K >

La t 34 34 'NLon135 34 'E 12:34

SPGP S

Exi t



OKSE L



UT C

34 34 'N13 5 34 'E 12:34

OKNull

******* Distress *******--- - - - - - Nature - - - - - - - -

UndesignatedFire ,Explos ionFloodingCol l is ionGroundingCapsiz ingSinkingDisable adr i f tAbandoning shipPiracy at tackMa n overboardEPIRB

emiss ion

OKSE L

******* DS C MENU *******--- - - - - - Select - - - - - - - -


OKSE L


[FREQ/CH][CH] [F ][CANCEL/CALL]


28/78

20

7 CALL PROCEDURE

D When no acknowledgement is receivedIf no acknowledgement is received, the emergencyalarm will sound continuously. In this case, the IC-M802 automatically transmits the distress call againevery 3.5 to 4.5 minutes.

Push [CANCEL/CALL] if you want to stop the alarm.

A distress relay call may be received after severalminutes from another ship if an acknowledgementcannot be received from a coast station directly.

CAUTION!DO NOT push [CANCEL/CALL] while waiting for anacknowledgement, otherwise the distress call repeatis cancelled.Push [CANCEL/CALL] only when you want to can-

cel repeated transmission.

D After receiving an acknowledgement callThe following should commence your voice transmis-sion after receiving a distress acknowledgement froma coast station (or another ship).

MAYDAYThis is ..... (your ship name). The 9-digit identity AND the call sign (orother identi cation of the ship)

The ship s position if the DSC distressdoes not included it.

The nature of the distress and assistancerequired.

Any other information which might facili-tate the rescue.


29/78

21

7CALL PROCEDURE

7

I Distress call to shipsGeneral DSC call with the distress category may beused for communications after the Distress call, e.g.

you want to change the operating mode, frequency,etc.

The call is transmitted one time only although the dis-tress call using the [DISTRESS] switch sends 5 timesrepeatedly.

RX

J3 EGP S

12.345.0

Exi t

SPLa t 34 34 'NLon135 34 'E 12:34

******* DS C MENU *******--- - - - - - Select - - - - - - - -


OKSE L

****** Individual ******--- - - - - Category - - - - - - -

Rout ineSafetyUrgencyDis t ress

OKSE L

****** Individual ******--- - - - Address ID - - - - - -

Manual se tIC-M802-1 123456789IC-M802-2 123456788IC-M802-3 123456787IC-M802-4 123456786IC-M802-5 123456785

OKSE L


987654321

OK

****** Individual ******-- - 1s t te lecommand - - - -

J3 ENo informat ion

OKSE L

****** Individual ******-- Traff ic f requency -- -

Manual se tT: 4567.0kHz IC-M802-1R: 4567.0kHzT:12345.0kHz IC-M802-2R:12345.0kHz

OKSE L


TX:_2134.0kHzRX:_2134.0kHz

OKSE L

****** Individual ******--- - Call f requency - - - - 2187.5kHz 4207.5kHz 6312.0kHz 8414.5kHz

12577.0kHz16804.5kHz

OKSE L

****** Individual ******--- - - - - - - Call - - - - - - - - -Category:Dis t ress To:987654321Traff ic :J3E TX 2134.0kHz RX 2134.0kHzCal l Freq:TX 2187.5kHz RX 2187.5kHz

Wri te-MenuCal l

DSC menu Category selection

Traffic frequency selection 1 Traffic frequency selection 2 Call frequency selection

Call stand-by screen

Manual ID input 1st telecommand selection Address ID selection

D Operation outline

Push [CANCEL/CALL] for 1 sec. tostart calling.Push [ENT] for 1 sec. to store thecondition into a TX memory chan-nel.


30/78

D Operation for distress call to ships

22

7 CALL PROCEDURE

q Push [DSC] to select DSC watch mode.w Push [MODE SET ] to select the DSC menu.

e Rotate [CH] to select Individual , then push[ENT].

rRotate [CH] to select Distress , then push[ENT].

t Rotate [CH] to select the desired pre-programmedID, or Manual set , then push [ENT]. When pre-programmed ID is selected, go to

stepu

.

y Enter the desired 9-digit MMSI code via the keypad. The number 0 (zero) cannot be entered for the 1st

digit, as the 1st digit 0 means group code.

u Rotate [CH] to select 1st telecommand, then push[ENT]. When No information is selected, go to

step !0 .

i Rotate [CH] to select the desired pre-programmedtraffic frequency, or Manual set then push[ENT]. When pre-programmed traffic frequency is se-

lected, go to step !0 .

o Enter the desired transmit and receive traffic fre-quency via the keypad, then push [ENT].

!0 Rotate [CH] to select the desired calling frequency,then push [ENT].

!1 The call stand-by screen is displayed as follows,verify the calling condition then push and hold[CANCEL/CALL] for 1 sec. to start calling.

!2 After the call, wait for an acknowledgement call. The calling is performed one time only.

RXJ2 B

GP S

< Wait fo r AC K >Individual

La t 34 34 'NLon135 34 'E 12:34

SP

Exi t

****** Individual ******--- - - - - - - Call - - - - - - - - -Category:Dis t ress To:987654321Traff ic :J3E TX 2134.0kHz RX 2134.0kHzCal l Freq:TX 2187.5kHz RX 2187.5kHz

Wri te-MenuCal l

****** Individual ******--- - Call f requency - - - - 2187.5kHz 4207.5kHz 6312.0kHz

8414.5kHz12577.0kHz16804.5kHz

OKSE L


TX:_2134.0kHzRX:_2134.0kHz

OKSE L



OKSE L


J3 E

No

informat ion

OKSE L


987654321

OK



OKSE L



OKSE L


[FREQ/CH][CH] [F ][CANCEL/CALL]


31/78

23

7CALL PROCEDURE

7

!3 When receiving the acknowledgement call, the dis-play shows the received ID code, or the called sta-tion name. Push [FREQ/CH];

-to select the traffic frequency if the called station isable to comply to the call.

-to return to DSC watch mode when unable.

************************* Individual AC K ** IC-M802 ** Able to comply *************************

Exi t

************************* Individual AC K ** IC-M802 ** Unable to comply ** Operator unavai lable *************************

Exi t

When the called station is unable to complyto the call, the reason may be displayed.

CONVENIENT! The IC-M802 has DSC TX memory. You can storeoften used DSC calling conditions for quick and sim-ple re-call. Up to 10 conditions can be stored into thememory with the following instructions.

When call stand-by screen is displayed as in step!1 at left, push and hold [ENT] for 1 sec.

Rotate [CH] to select the desired TX memory chan-nel number.

Push and hold [ENT] for 1 sec. again to store thecondition into the selected memory channel.

Push [ENT] to return to the calling stand-by condi-

tion.

Push and hold [CANCEL/CALL] for 1 sec. whentransmitting the DSC call in set condition, or push[MODE SET ] when returning to DSC watch mode.

****** TX memory *******--- - - - Individual - - - - - -Category:Dis t ress To:987654321Traff ic :J3E TX 2134.0kHz RX 2134.0kHzCal l Freq:TX 2187.5kHz RX 2187.5kHz

DELCal l

****** Individual ******-- - TX memory wri te - - - -

0 : Individual 9876543211:2:3:4:5:

OKSE L

****** Individual ******-- - TX memory wri te - - - -

0:1:2:3:4:5:

Wri teSE L


32/78

24

7 CALL PROCEDURE

I Urgency callWhen you want to send an urgency message, such asmedical transport announcement, etc., to other ships,

use Urgency as the category.An urgency call is sometimes called a PAN PAN call.

****** Al l ships ******* ****** Al l ships ******* ****** Al l ships *******

****** Al l ships *******

******* DS C MENU *******--- - - - - - Select - - - - - - - -


OKSE L



OKSE L

****** Al l ships *******--- - - - - Category - - - - - - -

Safe tyUrgency

OKSE L



OKSE L


987654321

OK


J3 ENo informat ion

OKSE L



OKSE L


TX:_2134.0kHzRX:_2134.0kHz

OKSE L


12577.0kHz

16804.5kHz

OKSE L

****** Individual ******--- - - - - - - Call - - - - - - - - -Category:Urgency To:987654321Traff ic :J3E TX 2134.0kHz RX 2134.0kHzCal l Freq:TX 2187.5kHz RX 2187.5kHz

Wri te-MenuCal l

DSC menu Category selection Category selection

Traffic frequency selection 1 Traffic frequency selection 2 Call frequency selection

Confirmation screen


D Operation outline

Push [CANCEL/CALL] for 1 sec. tostart calling.Push [ENT] for 1 sec. to store thecondition into the TX memorychannel.


33/78

25

7CALL PROCEDURE

7

e Rotate [CH] to select Urgency , then push[ENT].

r Rotate [CH] to select a traf c frequency from oneof the pre-programmed frequencies or Manualset then push [ENT]. When a pre-programmed frequency is selected,

go to step y .

t Enter the desired traffic frequencies for both thetransmit and receive, then push [ENT].

y Rotate [CH] to select the desired calling channel,then push [ENT].

u After the calling stand-by screen appears, pushand hold [CANCEL/CALL] for 1 sec. to transmit theurgency call. The transceiver is set to the traf c frequency after thecall transmission.

Push and hold [ENT] for 1 sec. to store the calling con-dition into the TX memory described in pages 23 and43, if desired.

i Announce the following message.

PAN PAN All stations (repeated 3 times). This is ..... (your ship name).

The 9-digit identity AND the call sign (orother identi cation of the ship)

The text of the urgency message.

****** Al l ships *******--- - - - - - - Call - - - - - - - - -Category:Urgency Traff ic :J3E TX 2134.0kHz RX 2134.0kHzCal l Freq:TX 2187.5kHz RX 2187.5kHz

Wri te-MenuCal l

****** Al l ships *******--- - Call f requency - - - - 2187.5kHz 4207.5kHz 6312.0kHz 8414.5kHz12577.0kHz16804.5kHz

OKSE L

****** Al l ships *******-- Traff ic f requency -- -

TX:_2134.0kHzRX:_2134.0kHz

OKSE L



OKSE L


Safe tyUrgency

OKSE L

D Urgency call operation

q Push [MODE SET ] to select the DSC menu.w Rotate [CH] to select either Individual or

All ships then push [ENT].

When selecting All ships


34/78

26

7 CALL PROCEDURE

e Select Urgency as the category using [CH],then push [ENT].

r Select (or enter) the 9-digit ID code, then push[ENT]. Use [CH] to select the ID code when the desired ship sID is pre-programmed.

Select Manual set with [CH] then push [ENT],after that, enter the desired 9-digit ID via the keypad.

t Rotate [CH] to select 1st telecommand, then push[ENT]. When No information is selected, go to

step i .

y Rotate [CH] to select the desired pre-programmedtraffic frequency, or Manual set then push[ENT]. When pre-programmed traffic frequency is se-

lected, go to step i .

u Enter the desired transmit and receive traffic fre-quency via the keypad, then push [ENT].

i Rotate [CH] to select the desired calling frequency,then push [ENT].

o The calling stand-by screen is displayed as fol-lows, verify the calling condition then push andhold [CANCEL/CALL] for 1 sec. to transmit the call. Push and hold [ENT] for 1 sec. to store the calling con-dition into the TX memory described in pages 23 and43, if desired.

!0 After sending the call, the transceiver waits for anacknowledgement.

RXJ2 B

GP S


La t 34 34 'NLon135 34 'E 12:34

SP

Exi t

****** Individual ******--- - - - - - - Call - - - - - - - - -Category:Urgency To:987654321Traff ic :J3E TX 2134.0kHz RX 2134.0kHzCal l Freq:TX 2187.5kHz RX 2187.5kHz

Wri te-MenuCal l


8414.5kHz12577.0kHz16804.5kHz

OKSE L


TX:_2134.0kHzRX:_2134.0kHz

OKSE L



OKSE L


J3 ENo informat ion

OKSE L


987654321

OK



OKSE L

****** Individual ******--- - - - - Category - - - - - - -Rout ineSafetyUrgencyDis t ress

OKSE L

When selecting Individual


35/78

27

7CALL PROCEDURE

7

!1 When receiving an acknowledgement, the displayshows the received ID code, or the called station

name. Push [FREQ/CH];-to select the traffic frequency if the called station isable to comply to the call.


!2 Announce the following message to the connectedstation.

PAN PAN

Desired station name (repeated 3times). This is ..... (your ship name). The 9-digit identity AND the call sign (orother identi cation of the ship)

The text of the urgency message.


Exi t


Exi t



36/78

28

7 CALL PROCEDURE

I Safety callWhen you want to send a safety message to otherships, use Safety as the category.

A safety call is sometimes called a SECURITE call.

****** Al l ships ******* ****** Al l ships ******* ****** Al l ships *******

****** Al l ships *******

******* DS C MENU *******--- - - - - - Select - - - - - - - -


OKSE L



OKSE L


Safe tyUrgency

OKSE L



OKSE L


987654321

OK


J3 ENo informat ion

OKSE L



OKSE L


TX:_2134.0kHzRX:_2134.0kHz

OKSE L


12577.0kHz16804.5kHz

OKSE L

****** Individual ******--- - - - - - - Call - - - - - - - - -Category:Safety To:987654321Traff ic :J3E TX 2134.0kHz RX 2134.0kHzCal l Freq:TX 2187.5kHz RX 2187.5kHz

Wri te-MenuCal l

DSC menu Category selection Category selection

Traffic frequency selection 1 Traffic frequency selection 2 Traffic frequency selection 3

Confirmation screen


D Operation outline

Push [CANCEL/CALL] for 1 sec. tostart calling.Push [ENT] for 1 sec. to store thecondition into the TX memorychannel.


37/78

29

7CALL PROCEDURE

7

D Safety call operation

A safety call procedure is almost the same as the ur-gency call.

q Push [MODE SET ] to select the DSC menu.w Rotate [CH] to select the desired DSC format from

Individual and All ships , then push[ENT].

When selecting All ships

e Rotate [CH] to select Urgency , then push[ENT].

r Rotate [CH] to select a traf c frequency from oneof the pre-programmed frequencies or Manualset then push [ENT]. When a pre-programmed frequency is selected,

go to step y .

t Enter the desired traffic frequencies for both thetransmit and receive, then push [ENT].

y Rotate [CH] to select the desired calling channel,then push [ENT].

u After the calling stand-by screen appears, pushand hold [CANCEL/CALL] for 1 sec. to transmit thesafety call. The transceiver is set to the traf c frequency after thecall transmission.

Push and hold [ENT] for 1 sec. to store the calling con-dition into the TX memory described in pages 23 and43, if desired.

i Announce the following message.

SECURITE (repeat 3 times) All stations (repeated 3 times). This is ..... (your ship name). The 9-digit identity AND the call sign (orother identi cation of the ship)

The text of the safety message.

****** Al l ships *******--- - - - - - - Call - - - - - - - - -Category:Safety Traff ic :J3E TX 2134.0kHz RX 2134.0kHzCal l Freq:TX 2187.5kHz RX 2187.5kHz

Wri te-MenuCal l

****** Al l ships *******--- - Call f requency - - - - 2187.5kHz 4207.5kHz

6312.0kHz 8414.5kHz12577.0kHz16804.5kHz

OKSE L


TX:_2134.0kHzRX:_2134.0kHz

OKSE L


Manual se t

T: 4567.0kHz IC-M802-1R: 4567.0kHzT:12345.0kHz IC-M802-2R:12345.0kHz

OKSE L


Safe tyUrgency

OKSE L


38/78

30

7 CALL PROCEDURE

When selecting Individual

e Select Safety as the category using [CH],then push [ENT].

r Select the desired 9-digit ID code, then push[ENT]. Use [CH] to select the ID code when the desired ship sID is pre-programmed.

Select Manual set with [CH] then push [ENT],after that, enter the desired 9-digit ID via the keypad.


step i .

y Rotate [CH] to select the desired pre-programmedtraffic frequency, or Manual set then push[ENT]. When the pre-programmed traffic frequency is

selected, go to step i .

u Enter the desired transmit and receive traffic fre-quency via the keypad, then push [ENT].

i Rotate [CH] to select the desired calling frequency,then push [ENT].

o The calling stand-by screen is displayed as fol-lows, verify the calling condition then push andhold [CANCEL/CALL] for 1 sec. to transmit the call. Push and hold [ENT] for 1 sec. to store the calling con-dition into the TX memory described in pages 23 and43, if desired.


RXJ2 B

GP S


La t 34 34 'NLon135 34 'E 12:34

SP

Exi t

****** Individual ******--- - - - - - - Call - - - - - - - - -Category:Safety To:987654321Traff ic :J3E TX 2134.0kHz RX 2134.0kHzCal l Freq:TX 2187.5kHz RX 2187.5kHz

Wri te-MenuCal l


8414.5kHz12577.0kHz16804.5kHz

OKSE L


TX:_2134.0kHzRX:_2134.0kHz

OKSE L



OKSE L


J3 ENo informat ion

OKSE L


987654321

OK



OKSE L

****** Individual ******--- - - - - Category - - - - - - -Rout ineSafetyUrgencyDis t ress

OKSE L


39/78

31

7CALL PROCEDURE

7

!1 When receiving an acknowledgement, the displayshows the received ID code, or the called station

name. Push [FREQ/CH];-to select the traffic frequency if the called station isable to comply to the call.


!2 Announce the following message to the connectedstation.

SECURITE (repeat 3 times)

Desired station name or all stations (repeated 3 times). This is ..... (your ship name). The 9-digit identity AND the call sign (orother identi cation of the ship)

The text of the safety message.


Exi t


Exi t



40/78

32

7 CALL PROCEDURE

I Routine callWhen you use DSC for general selective calling, useRoutine as the category.

q Push [MODE SET ] to select the DSC menu.w Rotate [CH] to select Individual then push

[ENT].e Select Routine as the category using [CH],

then push [ENT].

r Select the desired 9-digit ID code, then push[ENT]. Use [CH] to select the ID code when the desired ship sID is pre-programmed.

Select Manual set

with [CH] then push [ENT],after that, enter the desired 9-digit ID via the keypad.


step i .

y Rotate [CH] to select the desired pre-programmedtraffic frequency, or Manual set then push[ENT]. When pre-programmed traffic frequency is se-


u Enter the desired transmit and receive traffic fre-quency via the keypad, then push [ENT]. One of the voice channels, such as Tx/Rx: 2082.5 kHz,4146.0 kHz, should be used.

i Rotate [CH] to select the desired pre-programmedcalling frequency, or Manual set then push[ENT]. When the pre-programmed call frequency is se-

lected, go to step !0 .

oEnter the desired transmit and receive call fre-quency via the keypad, then push [ENT].

****** Individual ******--- - Call f requency - - - -

TX:_2345.0kHzRX:_2345.0kHz

OKSE L

****** Individual ******--- - Call f requency - - - -

Manual se tT: 2345.0kHz IC-M802-1R: 2345.0kHzT: 2177.0kHz SHIPR: 2177.0kHz

OKSE L


TX:_4567.0kHzRX:_4567.0kHz

OKSE L



OKSE L


J3 ENo informat ion

OKSE L


987654321

OK



OKSE L



OKSE L


41/78

33

7CALL PROCEDURE

7

!0 The calling stand-by screen is displayed as fol-lows, verify the calling condition then push andhold [CANCEL/CALL] for 1 sec. to transmit the rou-tine call. Push and hold [ENT] for 1 sec. to store the calling con-dition into the TX memory described in pages 23 and43, if desired.


!2 When receiving an acknowledgement, the displayshows the received ID code, or the called stationname. Push [FREQ/CH];

-to select the traffic frequency if the called station isable to comply to the call.

- to return to DSC watch mode when unable.

!3 Announce the following message to stations.- The 9-digit identity (or call sign or other identi -

cation) of the station which you want to call.- This is ..... (your ship name). - The 9-digit identity OR call sign (or other identi -

cation of the ship).

When no acknowledgement is received:q Wait for 5 min., then call again on the same or

a different frequency.w If no acknowledgement is received after a 2nd

call, wait for at least 15 min. before repeatingthe call.


Exi t


Exi t


RXJ2 B

GP S


La t 34 34 'NLon135 34 'E 12:34

SP

Exi t

****** Individual ******--- - - - - - - Call - - - - - - - - -Category:Rout ine To:987654321Traff ic :J3E TX 4567.0kHz RX 4567.0kHzCal l Freq:TX 2345.0kHz RX 2345.0kHz

Wri te-MenuCal l


42/78

34

7 CALL PROCEDURE

I Group callWhen you use DSC for calling the desired ship sgroup, use Group menu.

q Push [MODE SET ] to select the DSC menu.w Rotate [CH] to select Group then push [ENT].e Select the desired 9-digit group code, then push

[ENT]. Use [CH] to select the group code when the desiredgroup is pre-programmed.

When Manual set is selected, enter the desiredcode (last 8 digits only) via the keypad.-The rst digit 0 (zero) is xed for group code.

r Rotate [CH] to select the desired pre-programmedtraffic frequency, or Manual set then push[ENT]. When the pre-programmed traffic frequency is

selected, go to step y .

t Enter the desired transmit and receive traffic fre-quency via the keypad, then push [ENT]. One of the voice channel, such as Tx/Rx: 2082.5 kHz,4146.0 kHz, should be used.

y Rotate [CH] to select the desired pre-programmedcalling frequency, or Manual set then push[ENT]. When the pre-programmed call frequency is se-


u Enter the desired transmit and receive call fre-quency via the keypad, then push [ENT].

i The calling stand-by screen is displayed as fol-lows, verify the calling condition then push and

hold [CANCEL/CALL] for 1 sec. to transmit thegroup call. Push and hold [ENT] for 1 sec. to store the calling con-dition into TX memory described in pages 23 and 43, ifdesired.

o After sending the call, the traffic frequency is se-lected automatically.

!0 Announce the following message to stations.- The group name. - This is ..... (your ship name).

- The 9-digit identity OR call sign (or other identi -cation of the ship).

RXJ3 E

GP S

< Traff ic >

La t 34 34 'NLon135 34 'E 12:34

SP

Exi t

********* Group ********--- - - - - - - Call - - - - - - - - -To:087654321Traff ic :J3E TX 2134.0kHz RX 2134.0kHzCal l Freq:TX 2177.0kHz RX 2177.0kHz

Wri te-MenuCal l

********* Group ********--- - Call f requency - - - -

TX:_2345.0kHzRX:_2345.0kHz

OKSE L

********* Group ********--- - Call f requency - - - -

Manual se tT: 2345.0kHz IC-M802-1R: 2345.0kHzT: 2177.0kHz SHIPR: 2177.0kHz

OKSE L

********* Group ********-- Traff ic f requency -- -

TX:_2134.0kHzRX:_2134.0kHz

OKSE L

********* Group ********-- Traff ic f requency -- -


OKSE L

********* Group ********--- - - - - Group ID - - - - - - -

087654321

OK

********* Group ********--- - - - - Group ID - - - - - - -

Manual se tGroup-1 023456789Group-2 023456788Group-3 023456787Group-4 023456786Group-5 023456785

OKSE L


43/78

35

7CALL PROCEDURE

7

I Position request callThe position request call is used to con rm the speci

Icom IC-M802 Instruction Manual

Documents

Transcript of Icom IC-M802 Instruction Manual