IC330_ENG

OWNER’S MANUAL

3D Camcorder

Please read this manual carefully before operating your set and retain it for future reference.

IC330

P/NO : MFL67887203

1 Getting Started

Getting Started2

Getting S

tarted

1

Safety information

CAUTIONRISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO

USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the

product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing)

instructions in the literature accompanying the product.

WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

WARNING: Do not install this equipment in a confined space such as a book case or similar unit.

CAUTION: Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from over heating. The openings shall be never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product shall not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instruction has been adhered to.

Safe way to remove the battery or the battery from the equipment: Remove the old battery or battery pack, follow the steps in reverse order than the assembly. To prevent contamination of the environment and bring on possible threat to human and animal health, the old battery or the battery put it in the appropriate container at designated collection points. Do not dispose of batteries or battery together with other waste. It is recommended that you use local, free reimbursement systems batteries and accumulators. The battery shall not be exposed to excessive heat such as sunshine, fire or the like.

NOTICE: For safety marking information including product identification and supply ratings, please refer to the main label on the bottom of the apparatus.

Getting Started 3G

etting Started

1

WARNING:

� If the product or any of its accessories are not working properly, take them to your nearest qualified service centre. The personnel there will assist you and if necessary, arrange for the product to be repaired.

� Do not connect the power supply or operate your camcorder if it gets wet.

� Do not attempt to disassemble, repair, or modify the system on your own without seeking assistance from qualified service centre. It is extremely dangerous due to the high voltage running through the system. Contact the service centre.

� Do not plug in several electric devices to the same outlet. This may cause fire or electric shock.

� Keep the cables away from places where many people pass.

� Do not damage the cables such as by placing anything heavy on it.

CAUTION:

� Do not use the apparatus in a place with high magnetic, electric wave, or wireless devices such as a radio. Do not use the apparatus in a place with magnetic objects, electric frequencies, or vibration.

� The apparatus should not be exposed to water (dripping or splashing) and no objects filled with liquids, such as vases, shall be placed on the apparatus.

� The apparatus has been designed for outdoor use, however it is not designed to sustain direct exposure to water, rain, sleet, snow, sand, dust, or a direct splashing from a pool or even a cup of coffee. This action could permanently damage the internal parts of your camcorder.

� Do not spray cleaners directly on the camcorder. Doing so may pose a fire hazard.

� Keep the used lithium battery or memory card out of the reach of children. If the lithium battery or memory card is swallowed by a child, consult a physician immediately.

� Watching a 3D content for a long period time may cause dizziness or tiredness.

� It is not recommended to watch a movie in 3D mode for infirm, child and pregnant woman.

� If you are experiencing headache, tiredness or dizziness while viewing contents in 3D, it is strongly recommended to stop the playback and rest until you feel normal.

Warning on the LCD Screen

Caution must be observed when dealing with the fluid contained in the LCD. Make sure that fluid does not leak if the screen becomes cracked or damaged. If this occurs, follow these steps:

� Never use cleaning fluid or similar chemicals to clean the camcorder.

� If the fluid makes contact with the skin, wipe it with a clean cloth then rinse with a large amount of water.

� If the fluid makes contact with the eyes, wash eyes with clean water for at least 15 minutes and seek immediate medical attention.

� If the fluid is swallowed, first rinse mouth with water, then drink a large amount of water and induce vomiting. Seek immediate medical attention.

Getting Started4

Getting S

tarted

1

FCC Compliance Statement

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

� Reorient or relocate the receiving antenna.

� Increase the separation between the equipment and receiver.

� Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

� Consult the dealer or an experienced radio/TV technician for help.

CAUTION: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

FCC RF Radiation Exposure Statement : This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. End users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

CAUTION: Regulations of the FCC and FAA prohibit airborne operation of radio-frequency wireless devices because their signals could interfere with critical aircraft instruments.

Responsible Party : Inc.1000 Sylvan Avenue Englewood Cliffs, NJ 07632

TEL. : +1-800-243-0000

Getting Started 5G

etting Started

1

For Wireless product European Union Notice

LG Electronics hereby declares that this/these product(s) is/are in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC, 2004/108/EC, 2006/95/EC and 2011/65/EU.

Please contact to the following address for obtaining a copy of the DoC (Declaration of Conformity).

Contact office for compliance of this product: LG Electronics Inc EU Representative, Krijgsman 1, 1186 DM Amstelveen, The Netherlands

� Please note that this is NOT a Customer Service contact point. For Customer Service Information, see Warranty Card or contact the dealer that you purchased this product.

RF Radiation Exposure Statement

This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

Table of Contents6

Table of Contents

1 Getting Started2 Safety information8 Introduction8 – Features8 – Before you use8 – Copyright information8 – Unpacking9 Part and Control9 – Top/Left10 – Front/Back11 – Bottom

2 Preparation12 Preparing the Camcorder 13 – Inserting an SD card 14 – Inserting the battery 15 – Checking the battery condition 17 Selecting a mode

3 Operation18 Recording18 – Recording video18 – Adujstable operation19 – On Screen Display20 – Using menus in video camcorder

mode24 Playback25 – Changing view options in playback

mode27 – Connecting to TV (HDMI Cable)28 – Connecting to PC (USB Cable)29 Advanced Operation29 – Wireless Network Connection29 – Wi-Fi Connection32 – Sharing the file (SmartShare)33 – Uploading the file (LG Cloud)35 Managing the SET mode35 – Language35 – Date/Time35 – Date Format36 – Format36 – Initialize36 – Auto Power Off37 – Anti-flicker37 – Beep37 – Software update

Table of Contents 7

1

2

3

4

4 Appendix 38 Using edition program 38 – PC system requirements38 – PC system requirements (For 3D

Playing on PC)39 Video output specification40 SD Card Capacity41 Troubleshooting41 – Power41 – Display41 – Playback on other device (TV, etc.) 42 – Recording43 – Storage Media43 – Connecting to a computer44 Maintenance44 – Handling the unit44 – Open source software notice45 Trademarks and licenses46 Specifications

Getting Started8

Getting S

tarted

1

IntroductionRead this section to learn about the features and functions of the camcorder. This chapter also cover, package content, and descriptions of the hardware components.

FeaturesThe camcorder offers a variety of features and functions including:

� Records 3D and 2D videos (MP4)

� Takes 3D or 2D JPEG pictures

� LCD 3D display (8.13 cm)

� Parallax barrier auto-stereoscopic technology

� USB mass storage

� 3D glasses not required

� LG Cloud/Smart Share

� Wireless network connection

Before you useTake some test shots before performing a formal recording.

Before taking video clips or pictures with this camcorder in any important occasion (such as a wedding ceremony or an overseas trip), test the camcorder beforehand to ensure that it functions properly. Any additional loss caused by the malfunction of this product (such as costs of photography or any loss of benefit generated by the photography) is not the responsibility of the manufacturer and no compensation will be given for it.

Copyright informationObserve “No Photography” notices in certain locations. In these cases, you cannot record any live performance, improvisation or exhibits, even for personal purposes. Any transfer of pictures or memory card data must be conducted under the constraints of copyright law.

Unpacking

Contents

Camcorder

CD-ROM (Application

Software, Owner’s Manual)

USB Cable

Camcorder Pouch

45

Li-ion Battery

Simple Manual, Warranty card etc.

Mini HDMI to HDMI Cable 1.5M

SD Card (4 GB)

Getting Started 9G

etting Started

1

Part and ControlRefer to the following illustrations to familiarize yourself with the buttons and controls of this camcorder.

Top/Left

ij

a b

f

c

de

g

h

2D/3D DISP

MEMORY CARD BATTERY

MENU1

3D

12D REC

a W/T(Wide angle/ Telephoto) zoom lever:

� W (Wide angle): Wider range of view

� T (Telephoto): Close up view (page 19)

� Changing view options (page 25)

� Controlling the playback volume (page 26)

b PHOTO : Press to take a picture.

c 1(Power): Press to turn the camcorder on or off.

� Closing and opening the LCD panel can power on/off the camcorder.

d 2D REC 3D (Video/Photo) : Switches 2D/3D recording mode.

e MENU: Press to display the menu. Press again to return to the previous screen or close the menu.

f 1 : Press to exit the menu or return to the previous screen.

g 2D / 3D DISP (Display): Press to toggle between 3D and 2D modes on the LCD screen.

h : Press to delete all saved files or a file In playback mode.

i Speaker

j LCD Screen

Getting Started10

Getting S

tarted

1

Front/Back

a

b

c

d

EV- EV+

DISP

SETe

f

gh

i

j

a Lens Head: Rotate the lens head 90° to open the lens. (page 12)

b Lens

c LED Light

d Microphone

e Status LED: The color of the LED indicates the power or charging status etc. (page 17)

f [ ]: Recording/Playback/Stop/Confirmation

g Navigation buttons: In the menu, use the four-way control to select items in the menu.

In playback mode, use the buttons for playback, rewind/fast-forward speed, moving enlargement image (page 24-26)

� DISP (Up button) : Press to appear or disappear the display icons.

� (Down button) : Press to turn the LED

light on or off

� EV- (Left button) : Press to decrease the exposure values.

� EV+ (Right button) : Press to increase the exposure values.

h Mode Dial : Adjust to switch to different modes: Video/photo recording, playing back, sharing and setting. (page 17)

i USB Port

j HDMI Port

2 Preparation

Getting Started 11G

etting Started

1

Bottom

a b c d

a Tripod Mount

b SD Card/Battery Compartment (page13-14)

c Strap

d Cover latch

Preparation12

Preparation

2

Preparing the Camcorder

Using the grip strap Adjust the length of the grip strap so that the camcorder is stable when you press the recording start/stop [ ] button with your thumb.

Adjusting the LCD screen1. To turn on the power, open the LCD panel or

press 1 button.

2. Rotate the LCD screen towards the lens.

90°

90°

180°

� The screen opens up to 90°.

� To view the picture and video more conveniently, rotate the screen by 180° towards the lens, then fold it back to the body.

, Note

To record in mirror modeOpen the LCD panel 90° from the camcorder (a), then rotate it 180° to the lens side (b).

A mirror-image of the subject appears on the LCD screen, but the image will be recorded normally.

Opening the lensRotate the lens head to open the lens.

You can start recording.

Preparation 13P

reparation

2

Inserting an SD card Included SD card should be installed in the camcorder to provide storage space for video or photo files.

1. Slide the MEMORY CARD/BATTERY cover latch to open the SD CARD cover as shown in the illustration.

2. Insert the memory card. We recommend using a memory card with a capacity of 4 GB to 32 GB. (4 and 6 Class )

3 Close the MEMORY CARD/BATTERY cover.

If you pull out or insert the SD card during operating the camcorder, power will be turned off.

, Note

Maximum recording time

SD card capacity

MB

Video resolution

Bit rate Mbpes

Video Quality /

Recording time

(seconds)

4096

WVGAp 60 fps 8 High / 4084

720p 30 fps 8 High / 4084

720p 60 fps 12 High / 2723

1080p 12 High / 2723

4096

WVGAp 60 fps 6 Normal / 5445

720p 30 fps 6 Normal / 5445

720p 60 fps 10 Normal / 3267

1080p 10 Normal / 3267

� Make sure that label portion of SD card is facing up as inserting SD card illustration.

� Maximum recording time and quality will be different depending on the SD card capacity. (page 40)

, Note

Preparation14

Preparation

2

Maximum photo contents

SD card capacity MB 4096

Image quality High

Photo resolution 2M 4M 6M 12M

2D mode 3076 files

1741 files

1429 files

851 files

3D mode5449 files

4144 files

2195 files

1147 files

The number of recordable photos may vary depending on the recording conditions.

, Note

Inserting the battery 1. Slide the MEMORY CARD/BATTERY cover latch

to open the MEMORY CARD/BATTERY cover as shown in the illustration.

2 Rotate the plastic pin to insert the battery into the slot.

45

45

3. Close the MEMORY CARD/BATTERY cover.

Preparation 15P

reparation

2

Checking the battery condition The battery level display shows remaining battery capacity.

During battery

charging

Status (Connected)

USB is connected.

Battery level icon

Status (Dis-connected)

Battery level is full.

Battery level : 4/4

Battery level : 3/4

Battery level : 2/4

Battery level : 1/4

Battery level is too low (blinking) Change the

battery as soon as possible.

� The battery charging time : Approximately 300 minutes.

� The battery running time: Approximately 120 minutes. (Wi-fi off )

� The operating time on battery may vary depending on the battery status, operational status and environment conditions.

, Note

Recording/Playing time

Available time when you use a fully charged battery.

Continuous recording time

Typical recording

time

Playing time

2D 150 min. 40 min. (4GB SD

Card)

150 min.

3D 120 min. 40 min. (4GB SD

Card)

150 min.

The operating time on battery may vary depending on the battery status, operational status and environment conditions.

, Note

Preparation16

Preparation

2

Using a USB cable to charge the batteryYou can charge the battery with the USB cable. Follow the steps below to charge the battery.

1. Insert the Li-ion battery into the camcorder.

2. Connect the camcorder to PC with the USB cable provided as shown.

EV- EV+

DISP

SET

USB cable

3. The red LED will light up for proper charging.

4. Actual charging time depends on current battery capacity and charging conditions.

� Approximate charging time is 300 minutes.

� Turn off the camcorder to start charging the battery.

� Operation with all computers is not assured.

� If you connect the camcorder to a laptop computer that is not connected to a power source, the battery of the laptop computer will continue to use up its charge. Do not leave the camcorder connected to a computer in this manner.

� Charging with a personally assembled computer, with a converted computer, or through a USB hub are not guaranteed. The camcorder may not function properly, depending on the USB device which is used with the computer.

, Note

Using AC adapter to charge the batteryYou can charge the battery with AC adapter. Follow the steps below to charge the battery.

EV- EV+

DISP

SET

AC adapter is not included

1. Insert the Li-ion battery into the camcorder.Connect the camcorder to wall outlet with AC adapter.

2. The red LED will light up for proper charging.

� Actual charging time depends on current battery capacity and charging conditions.

� Turn off the camcorder to start charging the battery.

� We recommend to charge using AC adapter. (DC 5V 1.5A - 2A)

� AC adapter is not included. To charge with AC adapter, you should purchase proper charger.

, Note

Preparation 17P

reparation

2

To check the indicator condition

The color of the LED indicates the power, charging and operating conditions.

SET

LED color Condition Description

Power On Blinks until booting is finished.

Power Off Blinks once

Mode change Blinks until mode change is finished.

Recording start

Blinks until recording stop.

Recording stop

Blinks once

Shooting (half way)

Blinks during [PHOTO] button pressed

Shooting Blinks once

Delete Blinks until deleting file is finished.

Saving file Blinks until saving file is finished.

USB connection fail

Blinks until USB cable is successfully connected.

Low battery warning

Blinks when low battery icon is displayed.

Battery charging

When USB cable connect to the adapter or PC for charging the battery or sharing the data

Selecting a mode

The camcorder can be operated in four modes: Video camcorder, Playback, Sharing and setting mode. Adjust the Mode Dial to switch among modes.

-

DISP

SET

Mode Dial DescriptionVideo camcorder mode - You can record video and shoot still picture. (page 18)

Playback mode - You can search for recorded images by date and time of recording (Timeline view). (page 24)

Sharing mode - You can upload videos or photos on the Internet and share them with your family and friends. (page 32)

SET

Setting mode - You can change the settings of the unit in the [SET] menu. When the unit is turned on for the first time, you need to set the date and time properly. (Page 35)

3 Operation

Operation18

Operation

3

RecordingIn the default setting, videos are recorded in 3D with high definition image quality (HD).

Recording video1. Press 1 to turn on the camcorder.

2. Rotate the lens head and open the LCD screen.

3. Adjust the Mode Dial to select [ ] mode.

4. Press [ ] button to start the recording. When recording is start, “ REC” is displayed.

5. To stop video recording, press [ ] button again.

Before you start initial recording, set your “Language” and current “Date and Time” in the [SET] mode. (page 35)

, Note

Shooting photos To shoot a photo, do the following:

1. Press 1 to turn on the camcorder.

2. Rotate the lens head and open the LCD screen.

3. Rotate the Mode Dial to select the [ ]mode.

4. When you press [PHOTO] button halfway, focus area containing the subject is displayed on the LCD screen.

5. Press [PHOTO] button the rest of the way down to take picture.

� To record 3D content effectively, main subject should be over 1 m away from the camcorder.

�The maximum file size of each video recording is approximately 3.7 GB. The system will make another separated file automatically and record the video until the memory is full.

, Note

Adujstable operation

Switching recording mode 2D 3D3D mode allows you to record videos with 3D effects; 2D mode allows you to take regular 2D videos.

In video camcorder mode :

If you want to record 3D video, set to 3D mode using [2D REC 3D] switch on the camcorder.

1. Before you start recording, select 3D or 2D recording using [2D REC 3D] switch.

2. Press [ ] to start recording.

� Press [EV+/-] button to increase or decrease the Exposure Value settings.

� This feature cannot be used during recording.

, Note

Operation 19O

peration

3

Converting camcorder screen while recordingIf you feel uncomfortable on 3D LCD screen, press the [2D /3D DISP] button to switch the image from 3D to 2D.

1. On liveview screen, press [2D /3D DISP] button on the camcorder.

2. The liveview screen will be converted to 2D or 3D mode.

While taking a 3D photo, if you convert to 2D screen, the quick view image is devided into two same images side by side on the screen.

, Note

Using Zoom functionMove the power zoom lever to magnify or reduce the size of the image.

While you record video, move the zoom lever to [W] or [T] side. The screen will be magnified.

W (Wide angle): Wider range of view

T (Telephoto): Close up view

PHOTO

WIDE TELEW T

Using LED light It is possible to record with illumination even in dark places.

When you press [ ] button on camcorder, the light is turned on. to turn off, press [ ] button again.

On Screen Display

Video camorder mode screenDescribed here are icons for both recording video and shooting photo modes.

1hr/18m

a b c d e

f

g

h

i

j

a 2D/3D mode - displays current recording/ shooting mode.

b Counter (hour/ minute) - displays recordable time.

Photo number/total photo number- displays photographable number.

c Zoom (W: Wide/T: Telephoto) - displays the amount of zoom being used .

d SD Card - displays when the memory card is not inserted.

e Battery - displays remaining battery capacity.

f Video/Photo Resolution(size) - displays the current resolution.

g White Balance - displays the current White Balance mode.

h EV (Exposure Value) - displays the current exposure value.

i Focus area - displays when you press [PHOTO] button halfway in video camcorder mode.

j REC - displays recording status and elapsed recording time.

While recording or playback to hide or display the icons on the screen, press [DISP] button.

, Note

Operation20

Operation

3

Using menus in video camcorder modeIn Video camcorder mode, press [MENU] button to display menu and adjust White Balance, Effect and EV etc.

1. Press [MENU] button to display menu screen.

2. Select the first menu option then press [ ] to display the sub menu.

3. Select a desired option, then press [ ] button to confirm your selection.

4. Press [MENU] button or [1] button to exit the menu screen.

White BalanceThe White Balance menu allows you to set the white balance when capturing images under specific lighting conditions.

Select this option to let the camcorder set the white balance automatically.

Select this option for daylight filming.

Select this option for filming in cloudy days.

Select this option for fluorescent lighting.

Select this option for normal indoor lighting conditions.

Operation 21O

peration

3

EffectThe Effect menu allows you to change the recording effect.

Select it for color photography.

Select it for brown color effect.

Select it for black and white effect.

EV (Exposure Value)The EV (Exposure value) allows you to adjust the current exposure value.

Adjust EV (Exposure Value) to prevent a photo or video from under or over exposure.

When the main subject is darker than background, increase EV. If the subject is much lighter than the background, decrease the EV.

-2.0 to -1.0 To decrease the exposure, press [EV-] button.

±0 Normal exposure value.

+1.0 to +2.0 To increase the exposure, press [EV+] button.

Operation22

Operation

3

Video SizeThe Resolution menu allows you to set the resolution before you record a video. The higher the resolution, the more memory space is required.

1080P Select this option for 1920 x 1080 resolution.

720P 30fps Select this option for 1280 x 720 resolution at 30 fps.

720P 60fps Select this option for 1280 x 720 resolution at 60 fps.

WVGA Select this option for 848 x 480 resolution.

Photo SizeThe Resolution menu allows you to set the resolution before you shoot a photo. The higher the resolution, the more memory space is required.

3D/2D mode

2M Select this option for 1832 x 1030 resolution.

4M Select this option for 2592 x 1458resolution.



Operation 23O

peration

3

Night ModeThe Night Mode menu allows you to enable or disable the night mode feature.

On Turn night mode on. : When recording in the night or dark place.

Off Turn night mode off. : When recording in the daytime or light.

QualityThe Quality menu allows you to set the recording quality. Higher quality videos contain more details and therefore use more memory space.

Normal Select for normal recording quality.

High Select for higher recording quality.

The recordable capacity of memory card may vary depending on the recording quality.

, Note

3D Viewpoint

The 3D viewpoint menu allows you to set the 3D effect of the main subject. This function is only available if the Resolution setting is set to [1080P or 720P 30 fps].

Select if the main subject is 2 m away from the camcorder.

Select if the main subject is 5 m away from the camcorder.

Select if the main subject is over 5 m away (infinity) from the camcorder.

Operation24

Operation

3

Playback1. Press 1 to turn on the camcorder.

2. Make sure you are in playback mode. Rotate the Mode Dial to select [ ] mode.

3. Press [EV+] or [EV-] button to select the recorded videos.

4. Press [ ] button to start playback on the camcorder.

Icon Camcorder Description

Disp DISP

To appear or disappear the icons on screen display, press [DISP] button on the camcorder.

d/MTo play or pause, press [ ] button.

Z To stop playback, press [ ] button.

c/v EV+ / EV-

To play fast forward or reverse during playback. (X2, X4, X8 or X16) Press [EV+] or [EV-]button repeatedly.

� To have 3D effects videos/photos must be recorded in 3D mode

� If you are viewing with a regular 2D TV, the image will be divided on screen.

� For best results, maintain a 30-40 cm distance between your eyes and the LCD panel when previewing 3D photos or videos.

, Note

On-Screen display in playback modeYou can display and adjust various information and setting about the content.

a b c d e f

Icon Description

a 2D/ 3D mode Displays contents type.

Indicates that the file is shown by slide show.

b 100-0019 Current file number/ total number of files.

c 00:01:03 Indicates the total recording time.

d Indicates that is video file

e 0058/0059 Indicates the Video/Photo file number the current Video/Photo.

f Indicates that the file is protected.

Operation 25O

peration

3

Changing view options in playback mode

Viewing saved contents In video playback mode, you can change the viewing options by moving the zoom lever to (T)/(W) side.

1. When you change Mode Dial to playback mode, a full view screen is shown.

2. To go to grid view, move zoom lever to (W) side.

3. Move zoom lever one more time to (W) side, you can see timeline view.

Grid view

Full view

Timeline view

Timeline bar Date

Using timeline view You can search recorded videos/photos by date.

1. In video playback mode, change view type by moving zoom lever to (W) side repeatedly.

2. Whenever you press [EV-/EV+] button (left/right), recorded date is displayed on the time line bar.

3. To view the contents of selected date, press [] button.

� To return to full size screen, move the zoom lever to (T) repeatedly.

� When playing a content, play it back at full view screen.

� On the timeline bar, recorded date is displayed in one month interval.

, Note

Converting to 2D/3D contents If you feel uncomfortable while viewing 3D movies on the LCD screen for a long time, press the [2D /3D DISP] button to switch the image from 3D to 2D.

1. While playing 3D video/photo, [2D /3D DISP] button on the camcorder.

2. The video or photo screen will be converted to 2D or 3D mode.

Operation26

Operation

3

Enlargement photo imageIn video playback mode, you can magnify the photos using zoom lever in the full view image.

1. In video playback mode, select full view image of the photo.

2. Move the zoom lever to (T) side to zoom in for the image. You can move through zoom picture using [DISP/ /EV-/EV+] button .

3. To return to the normal picture size, press 1 button.

This function is only available for 2D photo image.

, Note

Controlling the volumeDuring playback video file, you can control the volume using zoom lever.

1. In video playback mode, play a video file.

2. Move the zoom lever to (T) side to increase the volume or (W) side to decrease .

Protecting contentsYou can protect a video from being deleted:

1. In video playback mode, press [EV-/EV+] (left/light) button to select the content you want to protect.

2. Press the [MENU] button to open the menu screen.

3. Use the [DISP/ ](up/down) button to select [Protection], then press [ ] button to confirm.

To release the protection content

1. Press [MENU] button after selecting the protected content.

2 Select [Protection] to release the protection.

Slide show for photosThe Auto-play function allows you to play each photos in turn.

To start auto-play, do the following:

1. In video playback mode, press the [EV-/EV+] button to select the photo to play.

2. Press the [MENU] button to open the menu screen.

3. Use [DISP/ ](up/down) button to select [Slide show], then press [ ] button to confirm.

To pause the slide show, press [ ] button.

Slide Show is available only for photo files. , Note

Deleting contentsTo delete a single contents

1. In video playback mode, press [EV-/EV+] (left/light) button to select the video/photo to delete.

2. Press [ ] button. “Do you want to delete?” message appears.

3. If you want to delete the content, select [YES].

4. Press [ ] button

Operation 27O

peration

3

To delete all contents

1. In video playback mode, move zoom lever to (W) side. Recorded video or photo files will be shown.

2. Press [ ] button in the grid view screen.

3. To check [√] all files, press [MENU] button.

If you delete a single content, check [√] in the content to delete using [ ] button.

4. Press [ ] button. “Do you want to delete?” message appears.

5. If you want to delete the file, select [YES] then press [ ] button.

� Once deleted files cannot be recovered. Ensure the files are transferred to the computer or saved in another storage device.

� Files that have been protected will not be deleted. You have to unlock the files first before deleting them.

� If you delete a file in timeline view, all files in same date will be deleted except files that user set to protected.

, Note

Connecting to TV (HDMI Cable)To play back videos and image on a TV, you can connect the camcorder to a TV using the supplied Mini HDMI to HDMI Cable 1.5 M.

HDMI is the interface for digital devices. If you connect this unit to a HDMI compatible high definition TV and then play back the recorded high definition images, you can enjoy them in high resolution with high quality audio.

EV- EV+

DISP

SET

Mini HDMI to HDMI Cable 1.5 M

1. Connect the camcorder to a TV HDMI compatible TV.

2. Set the TV’s source to HDMI (refer to TV’s owner’s manual).

3. Rotate the Mode Dial to select [ ] mode.

4. Play a video or photo content on the camcorder .

� For 3D video playback, you need to use a 3D HDTV.

� Since some factors affect the video output, see “ Video output specifications” for details (page 39).

� In case HDMI cable is connected to TV, [2D/3D DISP] button is not worked.

, Note

Operation28

Operation

3

Notes on HDMI cable connection:

- Use Mini HDMI to HDMI Cable 1.5 M with the HDMI logo.

- Use an HDMI mini connector on one end (for the camcorder), and a plug suitable for connecting your TV on the other end.

- Copyright-protected images are not output from the HDMI OUT jack of your camcorder.

- Some TVs may not function properly (e.g., no sound or image) with this connection.

- Do not connect the camcorder ‘s HDMI OUT jack to an external device’s HDMI OUT jack, as malfunction may result.

- HDMI (High Definition Multimedia Interface) is an interface to send both video/audio signals.

Connecting to PC (USB Cable)

Transferring files by connecting the camcorder to your PCYou can copy saved video or photo files to your PC by connecting the camcorder using a USB cable.

Connect the camcorder to your PC with the USB cable provided as shown.

EV- EV+

DISP

SET

USB cable

� When the camcorder is turned on and connected to a computer, the camcorder automatically is switched the mass storage mode.

� When you connect the USB cable to PC, “Used as USB storage” message will be displayed on the LCD screen. If you want to turn off USB storage, press [ ] button.

, Note

Notes on USB cable connection:

- Do not use any other USB cables except the included one. (Operation is not guaranteed with any other USB cables.)

- When this unit is connected to a PC using a USB cable while the unit is turned on, power is also supplied from the PC.

- When performing reading/writing between a PC and an SD card, be aware that some SD card slots built into PCs and some SD card readers are not compatible with the SDHC Memory Card or SDXC Memory Card.

- When the unit is connected to a PC, it cannot be turned off.

- Before turning this unit off, disconnect the USB cable.

Operation 29O

peration

3

Advanced Operation

Wireless Network ConnectionYou can connect to a WLAN using an AP (access point) in the wireless network service area.

Wireless Communication

Smart Device (PC or LG Smart TV)

Refer to the setup instructions supplied with your access point or wireless router for detailed connection steps and network settings. If you chose to use the wireless option, note that performance can sometimes be affected by other electronic devices in the home.

Wi-Fi ConnectionFor the wireless network connection, the camcorder needs to be set up for network communication. This adjustment can be done from Sharing mode [ ] menu. Adjust the [Wi-Fi connection] setting as follow. Setting up the access point or the wireless router is required before connecting the unit to the network.

Preparation

Before setting the wireless network, you need to:

- connect the broadband internet to the wireless home network.

- set the access point or wireless router.

- note the SSID and security code of the network.

1. Rotate the Mode Dial to switch to Sharing mode [ ] and then, select [MENU] to set Wi-Fi connection. All available networks are displayed on the screen.

Operation30

Operation

3

2. Select a desired SSID of wireless network and press [ ] button.

If you want to check available other network, select [ ] button and then, press [ ] button.

If you have security on your access point, you need to input the security code as necessary.

[ ] – Inserts a space at the cursor position.

[,] – Deletes the previous character at the cursor position.

[ABC/@#!] – Change the keyboard menu settings to capital letters, small letters or symbol.

� WEP security mode generally have 4 keys available on an access point setting. If your access point or wireless router use WEP security, enter the security code of the key “No.1” to connect on your home network.

� In An Access Point is a device that allows you to connect to your home network wirelessly.

, Note

3. Desired wireless network will automatically be connected to the unit. Select [OK] and press [] button to apply network settings.

If Wi-Fi connection is failed, the message “SSID connection fail” appears.

4. Network connection status is displayed on the screen.

Advanced settingIf you want to set the other network settings manually, press [MENU] button to select Set expert for Wi-Fi connection menu.

1. Select [MENU] button to set advanced network setting.

2. Select Network connections and press [ ] button.

3. When connecting via Wi-Fi, select the one of

the following network types.

Operation 31O

peration

3

If you have security on your access point or wireless router, verify that the WEP or WPA key that was entered into the device matches the router’s information code as necessary.

[Manual IP] – Scans all available access points or wireless routers within range and display them as a list. You can set [IP Address], [Subnet mask], [ Gate way] and [DNS Server] manually.

[Enter the (SSID)] – Your access point may not be broadcasting its network name (SSID). Check your access point settings through your computer and either set your access point to broadcast SSID, or manually enter the network name in [Enter the (SSID)].

[WPS PBC] – If your access point or wireless router supports the PBC (Push button Configuration) method, select this option and press the Push button on your access point within 120 counts. You do not need to know the network name (SSID) and security code of your access point.

4. Follow the instructions of each connection method on the screen.

� When you input a digit in the blank, key pad will be displayed on the screen.

� If you use other characters than the English alphabet or digits for the SSID of your access point (router), wireless connection may not be searched and connected.

, Note

Notes on network connection:� Many network connection problems during set

up can often be fixed by re-setting the router. After connecting the unit to the home network, quickly power off and/or connect the power cable of the home network router. Then power on and/or connect the power cable again.

� Depending on the internet service provider (ISP), the number of devices that can receive internet service may be limited by the applicable terms of service. For details, contact your ISP.

� Our company is not responsible for any malfunction of the unit and/or the internet connection feature due to communication errors/malfunctions associated with your broadband internet connection, or other connected equipment.

� Even if the unit is properly connected and configured, uploading a file may not operate properly because of internet congestion, the quality or bandwidth of your internet service, or problems at the provider of the content.

� Some internet connection operations may not be possible due to certain restrictions set by the Internet service provider (ISP) supplying your broadband Internet connection.

� Any fees charged by an ISP including, without limitation, connection charges are your responsibility.

� You must use a Router to use xDSL service.

� A DSL modem is required to use DSL service and a cable modem is required to use cable modem service. Depending on the access method and subscriber agreement with your ISP, you may not be able to use the internet connection feature contained in this unit or you may be limited to the number of devices you can connect at the same time. (If your ISP limits subscription to one device, this unit may not be allowed to connect when a PC is already connected.)

� The use of a “Router” may not be allowed or its usage may be limited depending on the policies and restrictions of your ISP. For details, contact your ISP directly.

� In the internet network that need browser approval, Wi-Fi service is limited.

Operation32

Operation

3

� The wireless network operate at 2.4 GHz radio frequencies that are also used by other household devices such as cordless telephone, Bluetooth® devices, microwave oven, and can be affected by interference from them.

� Turn off all unused network equipment in your local home network. Some devices may generate network traffic.

� For the purpose of the better transmission, place the unit from the access point as close as possible.

� In some instances, placing the access point or wireless router at least 0.45 m (1.5 ft.) above the floor may improve the reception.

� Move closer to the access point if possible or re-orient the unit so there is nothing between it and the access point.

� The reception quality over wireless depends on many factors such as type of the access point, distance between the unit and access point, and the location of the unit.

� Set your access point or wireless router to Infrastructure mode. Ad-hoc mode is not supported.

Sharing the file (SmartShare)You can enjoy the photos and videos at the linked Smart Device like PC or LG Smart TV by home network.

To use SmartShare function, do the following:

Preparation

- Check Wi-Fi connection on your 3D TV.

- This device and LG Smart TV must be connected to the same network through an App.

- Check the SmartShare’s setting in your LG Smart TV .

- Launch the SmartShare App. on LG Smart TV.

- Check list of connected smart devices in SmartShare.

- If preferrable devices are not found, check status of network.

1. Rotate the Mode Dial to select to [ ] sharing mode if not.

2. Select [SmartShare] then, press [ ] button.

Operation 33O

peration

3

3. When you select [SmartShare], Wi-Fi will be connected automatically.

If Wi-Fi connection is failed, select [MENU] button to set the Wi-Fi connection. (page 29)

4. Completion message will be appeared. After checking the message, play the Smartshare function in your LG Smart TV.

� If preferable devices are not found, check status of network.

� If you do not change the Mode Dial, Wi-Fi connection will be sustained.

, Note

Playing a file media from TV 1. Check the Wi-Fi device.

2. Play linked photos and videos files in your LG Smart TV from your camcorder.

� To be function, you need LG Smart TV that has smart share.

� Refer to the LG Smart TV’s manual to use SmartShare function.

� This camcorder and the PC must be connected to the same network.

� SmartShare feature cannot be used with some access point that do not support multicasting. For more information, refer to access point’s manual or consult with the manufacture.

� When you use Smart share, thumbnail is not supported in the player device.

� In the SmartShare, We recommend to play streaming files of 720p 30fps or WVGA resolution.

, Note

Uploading the file (LG Cloud)You can upload the stored photos and videos in your camcorder to LG Cloud (Web server).

To use LG Cloud function, do the following:

Preparation

- Check Wi-Fi connection on your camcorder.

- Before you Login to LG Cloud, Sign-up process is required to use. To sign-up, visit www.lgecloud.com using Smart TV, PC or Smart Phone.

1. Rotate the Mode Dial to select [ ] (Sharing mode) if not.

2. Select [LG Cloud] and then press [ ] button.

If wireless network is not connected to the camcorder, select [MENU] to set Wi-Fi connection. (Page 29)

3. Put in LG Cloud ID and Password you have already signed up.

When you put in the characters, keypad will be appeared on the LCD screen.

4. Select [Login] and then, press [ ] button.

Operation34

Operation

3

5. Select a category to view the stored files in an SD card.

Stored photos and videos are displayed on the LCD screen. The files are categorized by videos/photos depending on the contents type.

6. Select a file to upload to LG Cloud sever and then, press [ ] button. Repeat this step to select files as many you can.

7. To upload the file select [ ] then press [ ] button.

8. When uploading is finished, completion message is displayed.

� You can also upload selected multiple files at the same time.

� You cannot download stored files in LG Cloud web server.

� For more details about LG Cloud, visit www.lgecloud.com

� You can save up to three IDs in your camcorder.

� Uploading a large file may require a higher bandwidth connection and /or take long time to upload it.

� When uploading a large file, please be careful for the battery discharge.

, Note

To cancel the uploading file

To cancel uploading single file:

If you want to cancel uploading a single file, press [ ] button. the uploading file will be cancelled.

To cancel uploading multiple files:

When you upload multiple files at the same time, you can cancel the uploading using [EV+] button.

The uploading file is cancelled and then, next file will be uploaded.

Using Cloud menuIn LG Cloud mode, press [MENU] button to use the menu.

1Logout - allows you to logout LG Cloud1

Information - Shows Personal Info. and available space in the LG Cloud sever.

1

Help - Shows guide about using LG Cloud service.

Operation 35O

peration

3

Managing the SET modeBefore you start using the camcorder, some basic settings such as date and time, language and beep function need to be configured.

1. Rotate the Mode Dial to select [SET] mode to display [Settings] menu.

2. Select the first menu option then press [ ] to display the sub menu.

3. Select a desired option, then press [ ] button to confirm your selection.

4. Press [1] button to exit the [Settings] menu.

LanguageThe Language menu allows you to select the language displayed.

Date/TimeThe Date/Time menu allows you to adjust the date, time and DST (Summer Time).

If you set DST (Summer Time) function to [ON], the clock advances 1 hour.

When you press and hold [DISP] or [ ] buttons, setting value will be changed quickly.

Date FormatThe menu allows you to reset date format depending on the national custom or personal preference. Date / Time menu format will be changed as you select.

� YYYY-MM-DD : Year-Month-Date

� MM-DD-YYYY : Month-Date-Year

� DD-MM-YYYY : Date-Month-Year

Operation36

Operation

3

FormatThe Format menu allows you to format your memory card when memory card is inserted. Deletes and formats all data on the recording media.

� Formatting will delete everything in the memory card. You cannot restore images once they are deleted. Save important videos and photos in advance.

� Even if you delete data in the memory card or format the memory card on your camcorder or a computer, you may not delete data from the memory card completely.

, Note

InitializeThe Default menu allows you to reset the camcorder to factory defaults.

Auto Power OffThe Auto Power Off menu allows you to set an idle time after which the camcorder automatically turns off to save power.

� Off : Disable the Auto Power Off function.

� 1 min: Auto Power Off after 1 minute.

� 5 min: Auto Power Off after 5 minutes.

Operation 37O

peration

3

Anti-flickerThe Anti-flicker menu allows you to set the refresh rate of the camcorder. Increasing the refresh rate decreases flickering, thereby reducing eyestrain.

When surrounding light is extremely bright, flicker function may not work normally.

, Note

BeepThe Beep menu allows you to turn the operation sound and button sound off or on.

Software updateYou can update the unit using the latest software to enhance the products operation and/or add new features. You can update the new software by downloading from web site.

1. To download the Update version, visit http://www.lg.com

2. Download the software in your PC.

3 Insert supplied SD card or connect USB cable to your PC.

4. Copy the new software version into system folder of SD card.

5. Insert the SD card to your camcorder or disconnect the connected USB cable to update it.

6. If a new version is found, Current version and Update version is displayed on the LCD screen.

� During the software update procedure, do not turn off the unit or pull out the battery, an SD card. If software update has not been properly, some functions may not work normally.

� This unit cannot be updated to previous software version.

, Note

4 Appendix

Appendix38

Appendix

4

Using edition program You can save movies and photos in your PC and the saved files are able to edit by installing Arcsoft Total Media™ HDCam.

Importing files

Playback /Edition

Media management

You can transport the media files from the camcorder to edit, upload, and produce photo books and album pages.

Playback capability

You can view photos and play video clips using Arcsoft Total Media™HDCam.

To use the program, please refer to the Quick Setup Guide in the included CD manual.

PC system requirementsThe camcorder requires a PC with the following specifications:

� Windows® 7 / Vista / XP SP2 operating system

� Intel®/AMD Dual-Core CPU or higher

� At least 1 GB of RAM or higher

� At least DirectX 9 video card, DirectX 10 is recommended

� Standard USB 1.1 port or higher

� At least 2 GB or greater available hard disk

PC system requirements (For 3D Playing on PC)� Windows® 7 / Vista operating system

� Intel® Core 2 Duo or AMD Athlon X2 CPU or higher

� At least 1 GB of RAM or higher

� NVIDIA GeForce 8, 9 and 200 series

� Standard USB 1.1 port or higher

� At least 2 GB or greater available hard disk

� 3D ready monitor (120 Hz)

� 3D vision kits

Appendix 39A

ppendix

4

Video output specification

Recording/ShootingSlide Switch Disp button LCD Panel Output HDMI Output1) Contents

Set 2DSet 2D

2D Output 2D Output 2D ContentsSet 3D

Set 3DSet 2D 2D Output

3D Output 3D Contents Set 3D 3D Output

1) In recording mode, HDMI output is different depending on your 3D or 2D setting.

PlaybackContents Disp button LCD Panel Output HDMI Output 2)

2D ContentsSet 2D

2D Output 2D OutputSet 3D

3D ContentsSet 2D 2D Output 2D Output

Set 3D 3D Output 3D Output

2) In playback mode, HDMI output is different depending on your 3D or 2D setting using [Disp] button.

Appendix40

Appendix

4

SD Card Capacity

Data Size Video resolution Video Quality Bit rate (Mbps) Recording time (min)

4G Byte WVGAp60 High 8 67.48

720p30 8 67.48

720p60 12 45

1080p 12 45

WVGAp60 Normal 6 89.92

720p30 6 89.92

720p60 10 54

1080p 10 54


720p30 8 134.96

720p60 12 90

1080p 12 90


720p30 6 179.84

720p60 10 108

1080p 10 108


720p30 8 269.92

720p60 12 180

1080p 12 180


720p30 6 359.68

720p60 10 216

1080p 10 216


720p30 8 539.84

720p60 12 360

1080p 12 360


720p30 6 719.36

720p60 10 432

1080p 10 432

Appendix 41A

ppendix

4

Troubleshooting

PowerSymptom Cause & Solution

The camcorder does not turn on.

� The battery may not be installed in your camcorder. Insert the battery into the camcorder.

� The inserted battery may be discharged. Charge the battery or replace it with a charged one.

� If you use the AC power adapter, make sure it is properly connected to a wall outlet.

The power turns off automatically.

� Is Auto Power Off set to [1 Min] or [5 Min]? If no button is pressed for about 1 minute or 5 minutes, the camcorder is automatically turned off [Auto Power Off ]. To disable this option, change the setting of [Auto Power Off ] to [Off ].

� The battery is almost exhausted. Charge the battery or replace it with a charged one.

The battery discharges quickly.

� The temperature is too low.

� The battery is not fully charged. Charge the battery again.

� The battery has reached the end of its life span and cannot be recharged. Use another battery.

Display

Symptom Cause & Solution

The TV screen or LCD display has distorted images or stripes at the top/bottom or on the left/right.

This can occur when recording or viewing a 16:9 ratio image on a 4:3 ratio TV. For more details, see the display specification.

Playback on other device (TV, etc.) Symptom Cause & Solution

The image appears distorted on a TV.

� This phenomenon is caused by connecting to a TV with 4:3 aspect ratio.

You cannot view the image on or hear the sound from a TV connected using the HDMI cable.

� The camcorder cannot output Images from the HDMI jack if the material is copyright protected.

Appendix42

Appendix

4

RecordingSymptom Cause & Solution

Pressing the recording start/stop button does not start recording.

� Set your camcorder to the recording mode.

� There is not enough free space to record on the storage media.

� Check if memory card is not inserted or write-protect tab is set to lock.

The actual recording time is less than the estimated recording time.

� There is no more free space for recording on the storage media. Back up important files on your PC and format the storage media or delete the unnecessary files.

� If you make recordings or delete files frequently, the performance of the storage media deteriorates. If this occurs, format the storage media again.

� If you use a memory card with low writing speed, the camcorder automatically stops recording videos and a corresponding message appears on the LCD screen.

The recording stops automatically.

� The temperature is too low.

� The battery is not fully charged. Charge the battery again.

� The battery has reached the end of its lifespan and cannot be recharged. Use another battery.

You cannot record a photo image.

� Set your camcorder to [ ] mode (video camcorder mode).

� Release the lock on the write-protection tab of the memory card if any.

� The storage media is full. Use a new memory card or format the storage media. Or remove unnecessary images.

You don’t hear the beep sound.

� Set [Beep] option to [On] in the [Settings] menu.

� The Beep sound is turned off temporarily when you record videos.

� When the mimi HDMI cable is connected to the camcorder, the Beep Sound is disabled temporarily.

There is a time difference between the point where you press the recording start/stop button and the point where the recorded video starts/stops.

On your camcorder, there may be a slight time delay between the point where you press the recording start/stop button and the actual point where the recorded video starts/stops. This is not a malfunction.

Horizontal stripes appear on the images.

This can occur when recording images under a fluorescent lamp, sodium lamp, or mercury lamp. This is not a malfunction.

Appendix 43A

ppendix

4

Storage Media


Image cannot be deleted. � Release the lock on the write-protect tab of the memory card (SDHC/SD memory card), if any.

� You cannot delete a protected images. Release protection of the image using the Protect function.

You cannot format the memory card.

� Release the lock on the write-protect tab of the memory card (SDHC/SD memory card), if any.

� The memory card is not supported on your camcorder or it has some problems.

Connecting to a computer


Your computer does not recognize your camcorder.

� Disconnect the USB cable from the computer and camcorder, restart the computer, and then connect the USB cable again correctly.

Cannot play back a video file properly on a PC.

� You need a video codec to play back the file recorded on your camcorder. Install the software provided with your camcorder.

� Make sure you insert the connector in the correct orientation, and connect the USB cable to the micro USB jack on your camcorder firmly.

� Disconnect the cable from the computer and camcorder, restart the computer, and then connect the cable again properly.

� To play back an HD video file, you need a computer with better specifications.

� Use a computer with the recommended specifications.

Your computer is not playing videos, images, or sound located on your camcorder properly.

� Video playback or sound may stop temporarily depending on your computer. The video or sound copied to your computer is not affected.

� If your camcorder is connected to a computer that does not support Hi-speed USB (micro USB 2.0), the image or sound may not play back correctly. Images, video, and sound copied from the camcorder to your computer are not affected.

The playback screen is paused or distorted.

� Check the system requirements to play a video.

� Shut down all other applications currently running on the computer.

� If you play back a video on your camcorder when it is connected to a computer, the video may not play back smoothly on the computer, depending on the transfer speed. Please copy the file to your PC, and then play it back.

Appendix44

Appendix

4

Maintenance

Handling the unit

When shipping the unitPlease save the original shipping carton and packing materials. If you need to ship the unit, for maximum protection, re-pack the unit as it was originally packed at the factory.

Cleaning the unitTo clean the unit, use a soft, dry cloth. If the surfaces are extremely dirty, use a soft cloth lightly moistened with a mild detergent solution. Do not use strong solvents such as alcohol, benzine, or thinner, as these might damage the surface of the unit.

Keeping the exterior surfaces clean

� Do not use volatile liquids such as insecticide spray near the unit.

� Wiping with strong pressure may damage the surface.

� Do not leave rubber or plastic products in contact with the unit for a long period of time.

� Keep the LCD screen closed when you are not using your camcorder.

� Do not wrap your camcorder with a towel, for example, and operate it. Doing so might cause heat to build up inside.

� Do not use a deformed or damaged battery pack.

Operation conditions� This camcorder is designed for use in

temperatures ranging from 0 °C to 40 °C (32 °F to 104 °F).

� Do not use or keep the camcorder in the following areas:

- In areas subject to direct sunlight

- In areas subject to high humidity or dust

- Near air conditioners, heaters, or other areas subject to temperature extremes

- Inside of a closed vehicle, especially one parked in the sun.

- In areas subject to strong vibration

Power supply� Use only the type of battery that came with

your camcorder. Using any other type of battery may damage the equipment and invalidate the warranty.

� Do not short the battery terminals. The battery could overheat.

� Do not attempt to split or peel the outer casing.

�Remove the battery if the camcorder is not going to be used for a long time. If the battery is left unused for more than 3 months, you need to charge the battery before use.

Open source software noticeTo obtain the corresponding source code under GPL, LGPL and other open source licenses, please visit http://opensource.lge.com. All referred license terms, warranty disclaimers and copyright notices are available to download with the source code.

Appendix 45A

ppendix

4

Trademarks and licenses

The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

SDHC Logo is a trademark of SD-3C, LLC.

The Wi-Fi CERTIFIED Logo is a certification mark of the Wi-Fi Alliance.

Appendix46

Appendix

4

Specifications

General

Power source 5V 1.0~2.0A USB Power Input , Li-ion Battery 1700mAh Input

Operating humidity 60 %

Operating temperature 0 °C to 40 °C (32 °F to 104 °F).

Imaging sensor 7.93 mm 5 M CMOS Sensor x 2

Active pixels 5.0 Megapixel

Storage media Internal: Built-in 256 MB Flash Memory (not available for contents storage.)

External: SD card (Up to SDHC 32 GB Class6)

File system : FAT 16/32

Sensitivity Auto

Lens F3.2, f=5.7 mm

Still image File formats: JPEG (Exif 2.2)

Resolution: 2D/3D Still image: 2M, 4M, 6M, 12M (Firmware Interpolation)

Movie File formats: Video codec: H.264 ; Audio codec : AAC ; Container Format: MP4

Resolution: 2D/3D Movie : WVGA 848 x 480 60 fps, 720p 30/60 fps, 1080p 30 fps

Zoom (Digital zoom) 3D: 4X, 2D: 10X

LCD monitor 81.3 mm color LCD monitor (320x480 pixels)

Focus Range Approx. 1500 mm to infinity

Exposure mode Programmed AE

LED light Effective range: < 1 m Mode: On/Off

White balance Auto/Sunny/Cloudy/Fluorescent/Tungsten

EV compensation -2.0 EV to +2.0 EV

Wi-Fi IEEE802.11b/g/n, WMM-PS, WPS

LG Cloud LG Cloud service (Upload only )

Shutter speed Video: 1/15 to 1/2000 second

Still: 2 to 1/4000 second

Interface Audio /Video Out : HDMI OUT jack: HDMI mini connector

USB jack : micro USB port (mini-AB/typeA), USB 2.0 High-speed

Power supply Li-ion Battery NP120 (1700 mAh)

Dimensions (W x H x D) Approx. 36 (W) mm x 65 (H) mm x 126 (D) mm

Weight Approx. 220 g ± 10 g (Excluding battery and memory card)

� Design and specifications are subject to change without notice.

The notified body performed

and issued the certificate

Name and address of the Manufacturer

Name and Surname / Function:

LG Electronics Inc. – EU Representative

Krijgsman 1 - 1186 DM Amstelveen - The Netherlands Doo Haeng Lee / Director

The last two digits of the year in which the CE marking was affixed

EU DECLARATION OF CONFORMITY

Object of the declaration

Number

DOC_IC330_130219

This declaration of conformity is issued under the

sole responsibility of the manufacturer: LG Electronics Inc.

Product information Product Name

Model Name

3D Camcorder

IC330

Additional information

The object of the declaration described above is in conformity with the relevant Community harmonisation

legislations: - References to the relevant harmonized standards used or references to the technical specifications in relation to which

conformity is declared

• Low Voltage Directive: 2006/95/EC • RoHS Directive: 2011/65/EU EN 62321

EN 50581 : 2012 EN 60950-1:2006+A11:2009+A1:2010

+A12:2011

a conformity assessment of the technical

construction file, including the test reports

13

Signed for and on behalf of: LG Electronics Inc.

Place:

February 19.2013

Date of issue:

N/A

• R&TTE Directive: 1999/5/EC

ETSI EN 300 328 V1.7.1:2006

EN 301 489-17 V2.2.1:2012

• EMC Directive: 2004/108/EC

DXG Technology Corp.

15Fl., No. 4, Sec. 3, Ming-Chuan East Rd., Taipei, Taiwan R.O.C.

Additional information

N/A

0560

EN 55022:2010

EN 55024:2010 EN 301 489-1 V1.9.2:2011

EN 62311:2008

Name: Telefication

Number: 0560

1 (EN) EU Declaration of Conformity / (BG) ДЕКЛАРАЦИЯ ЗА СЪОТВЕТСТВИЕ С ИЗИСКВАНИЯТА НА ЕС / (ES) Declaración UE de Conformidad / (CS) EU Prohlášení o shodě / (DA) EU-

Overensstemmelseserklæ ring / (DE) EU-Konformitätserklärung / (ET) ELi Vastavusdeklaratsioon / (EL) ΔΗΛΩΣΗ ΣΥΜΜΟΡΦΩΣΗΣ ΕΕ / (FR) Déclaration UE de Conformité / (GA) Dearbhú

Comhréireachta an AE / (IT) Dichiarazione UE di Conformità / (LV) ES Atbilstības Deklarācija / (LT) ES Atitikties Deklaracija / (HU) EU-Megfelelőségi Nyilatkozat/ (MT) Dikjarazzjoni Tal-

Konformità Tal-UE / (NL) EU Conformiteitsverklaring / (PL) Deklaracja Zgodności UE / (PT) Declaração de Conformidade UE / (RO) Declarația de Conformitate UE / (SK) Vyhlásenie o Zhode

EÚ / (SL) Izjava EU o Skladnosti / (FI) EU-Vaatimustenmukaisuusvakuutus / (SV) EU-Försäkran om Ö verensstämmelse

2 (EN) Number / (BG) № / (ES) No / (CS) Č. / (DA) Nr. / (DE) Nr. / (ET) Nr / (EL) Αριθ. / (FR) No / (GA) Uimhir / (IT) N. / (LV) Nr. / (LT) Nr. / (HU) Szám / (MT) Numru / (NL) Nr. / (PL) Nr /

(PT) N.o / (RO) Nr / (SK) Číslo / (SL) Št. / (FI) N:o / (SV) Nr

3 (EN) Name and address of the Manufacturer / (BG) Наименование и адрес на производителя / (ES) Nombre y dirección del fabricante / (CS) Obchodní jméno a adresa výrobce / (DA)

Fabrikantens navn og adresse / (DE) Name und Anschrift des Herstellers / (ET) Valmistaja nimi ja aadress / (EL) Όνομα και διεύθυνση κατασκευαστή / (FR) Nom et adresse du fabricant / (GA)

Ainm agus seoladh an Mónaróra / (IT) Nome e indirizzo del fabbricante / (LV) Ražotāja nosaukums un adrese / (LT) Gamintojo pavadinimas ir adresas / (HU) Gyártó neve és címe / (MT) Isem u

indirizz tal-manifattur / (NL) Naam en adres van de fabrikant / (PL) Nazwa i adres producenta / (PT) Nome e endereço do fabricante / (RO) Numele și adresa Producătorului / (SK) Obchodné

meno a adresa výrobcu / (SL) Ime in naslov proizvajalca / (FI) Valmistajan nimi ja osoite / (SV) Tillverkarens namn och adress

4 (EN) This declaration of conformity is issued under the sole responsibility of the manufacturer / (BG) За настоящата декларация за съответствие отговорност носи единствено

производителят / (ES) La presente declaración de conformidad se expide bajo la exclusiva responsabilidad del fabricante / (CS) Toto prohlášení o shodě vydal na vlastní odpovědnost výrobce

/ (DA) Denne overensstemmelseserklæ ring udstedes på fabrikantens ansvar / (DE) Diese Konformitätserklärung wird unter der alleinigen Verantwortung des Herstellers abgegeben / (ET)

Käesolev vastavusdeklaratsioon on välja antud valmistaja ainuvastutusel / (EL) Η παρούσα δήλωση συμμόρφωσης εκδίδεται με αποκλειστική ευθύνη του κατασκευαστή / (FR) La présente

déclaration de conformité est établie sous la seule responsabilité du fabricant / (GA) Eisítear an dearbhú comhréireachta faoi fhreagracht aonair an mhonaróra / (IT) La presente dichiarazione di

conformità è rilasciata sotto la responsabilità esclusiva del fabbricante / (LV) Šī atbilstības deklarācija ir izdota vienīgi uz šāda ražotāja atbildību / (LT) Ši atitikties deklaracija išduota tik gamintojo

atsakomybe / (HU) E megfelelőségi nyilatkozat a gyártó kizárólagos felelősségére kerül kibocsátásra / (MT) Din id-dikjarazzjoni tal-konformità tinħareg taħt ir-responsabbiltà unika tal-manifattur /

(NL) Deze conformiteitsverklaring wordt verstrekt onder volledige verantwoordelijkheid van de fabrikant / (PL) Niniejsza deklaracja zgodności wydana zostaje na wyłączną odpowiedzialność

producenta / (PT) A presente declaração de conformidade é emitida sob a exclusiva responsabilidade do fabricante / (RO) Prezenta declarație de conformitate este emisă pe răspunderea

exclusivă a producătorului / (SK) Toto vyhlásenie o zhode sa vydáva na výhradnú zodpovednosť výrobcu / (SL) Ta izjava o skladnosti se izda na lastno odgovornost proizvajalca / (FI) Tämä

vaatimustenmukaisuusvakuutus on annettu valmistajan yksinomaisella vastuulla / (SV) Denna försäkran om överensstämmelse utfärdas på tillverkarens eget ansvar

5 (EN) Object of the declaration / (BG) Обект на декларацията / (ES) Objeto de la declaración / (CS) Předmět prohlášení / (DA) Erklæ ringens genstand / (DE) Gegenstand der Erklärung / (ET)

Deklareeritav ese / (EL) Σκοπός της δήλωσης / (FR) Objet de la déclaration / (GA) Cuspóir an dearbhaithe / (IT) Oggetto della dichiarazione / (LV) Deklarācijas priekšmets / (LT) Deklaracijos

objektas / (HU) A nyilatkozat tárgya / (MT) L-għan tad-dikjarazzjoni / (NL) Voorwerp van de verklaring / (PL) Przedmiot deklaracji / (PT) Objecto da declaração / (RO) Obiectul declarației / (SK)

Predmet vyhlásenia / (SL) Predmet izjave / (FI) Vakuutuksen kohde / (SV) Föremål för försäkran

6 (EN) Product information; Product Name; Model Name / (BG) Информация за продукта, името на продукта, името на модела / (ES) Información del producto; nombre del producto;

nombre del modelo / (CS) Informace o výrobku; Název výrobku; Název modelu / (DA) Produkt information; Produktnavn; Modelnavn / (DE) Produktinformation; Produktname; Modellname / (ET)

Toote kirjeldus; Toote nimetus; Mudeli nimi / (EL) Πληροφορίες για το προϊόν, όνομα προϊόντος, όνομα μοντέλου / (FR) Information sur le produit; Nom du produit; Nom du modèle / (GA)

Faisnéis Táirge; Ainm Táirge; Ainm Múnla / (IT) Informazioni sul prodotto; denominazione del prodotto; Nome del modello / (LV) Informācija par izstrādājumu; Izstrādājuma nosaukums; modeļa

nosaukums / (LT) Informacija apie produktą; produkto pavadinimas; modelio pavadinimas / (HU) Termékinformáció; a termék neve; típusnév / (MT) Informazzjoni tal-prodott; isem tal-prodott;

isem tal-mudell / (NL) Product informatie, Product naam; Model naam / (PL) Informacje o produkcie; nazwa produktu; nazwa modelu / (PT) Informação sobre o produto; Nome do Produto;

Designação do Modelo / (RO) Informaţii despre Produs; Denumire Produs; Nume Model / (SK) Informácie o výrobku; Názov výrobku; Názov modelu / (SL) Podatki o izdelku; ime izdelka; ime

modela / (FI) Tuotetiedot; tuotteen nimi; malli nimi / (SV) Produktinformation; produktnamn; modellnamn

7 (EN) Additional information / (BG) Допълнителна информация / (ES) Información adicional / (CS) Další informace / (DA) Supplerende oplysninger / (DE) Zusätzliche Angaben / (ET)

Lisateave / (EL) Συμπληρωματικές πληροφορίες / (FR) Informations supplémentaires / (GA) Faisnéis bhreise / (IT) Ulteriori informazioni / (LV) Papildu informācija / (LT) Papildoma informacija /

(HU) Kiegészítő információk / (MT) Informazzjoni addizzjonali / (NL) Aanvullende informatie / (PL) Informacje dodatkowe / (PT) Informações complementares / (RO) Informații suplimentare / (SK)

Dodatočné informácie / (SL) Dodatni podatki / (FI) Lisätietoja / (SV) Ytterligare information

8 (EN) The object of the declaration described above is in conformity with the relevant Community harmonisation legislations / (BG) Предметът на декларацията, описан по-горе,

отговаря на съответното законодателство на Общността за declaración descrita anteriormente es conforme a la legislación comunitaria de armonización pertinente / (CS) Výše

popsaný předmět prohlášení je ve shodě s harmonizovanými právními předpisy Společeхармонизация / (ES) El objeto de lanství / (DA) Genstanden for erklæ ringen, som beskrevet ovenfor, er i

overensstemmelse med den relevante EF-harmoniseringslovgivning / (DE) Der oben beschriebene Gegenstand der Erklärung erfüllt die einschlägigen Harmonisierungsrechtsvorschriften der

Gemeinschaft / (ET) Ü lalkirjeldatud deklareeritav toode on kooskõlas asjaomaste ühenduse ühtlustatud õigusaktidega / (EL) Ο στόχος της δήλωσης που περιγράφεται παραπάνω είναι σύμφωνος

προς τη σχετική κοινοτική νομοθεσία εναρμόνισης / (FR) L'objet de la déclaration décrit ci-dessus est conforme à la législation communautaire d'harmonisation applicable / (GA) Tá cuspóir an

dearbhaithe a thuairiscítear thuas i gcomhréir le reachtaíocht ábhartha um chomhchuibhiú de chuid an Chomhphobail / (IT) L’oggetto della dichiarazione di cui sopra è conforme alla pertinente

normativa comunitaria di armonizzazione / (LV) Iepriekš aprakstītais deklarācijas priekšmets atbilst attiecīgajam Kopienas saskaņotajam tiesību aktam / (LT) Pirmiau aprašytas deklaracijos

objektas atitinka susijusius derinamuosius Bendrijos teisės aktus / (HU) A fent ismertetett nyilatkozat tárgya megfelel a vonatkozó közösségi harmonizációs jogszabálynak / (MT) L-għan tad-

dikjarazzjoni deskritt hawn fuq huwa konformi mal-leġiżlazzjoni ta' armonizzazzjoni rilevanti tal-Komunità / (NL) Het hierboven beschreven voorwerp is conform de desbetreffende communautaire

harmonisatiewetgeving / (PL) Wymieniony powyżej przedmiot niniejszej deklaracji jest zgodny z odnośnymi wymaganiami wspólnotowych przepisów harmonizacyjnych / (PT) O objecto da

declaração acima mencionada está em conformidade com a legislação comunitária aplicável em matéria de harmonização / (RO) Obiectul declarației descris mai sus este în conformitate cu

legislația comunitară relevantă de armonizare / (SK) Uvedený predmet vyhlásenia je v súlade s príslušnými harmonizačnými právnymi predpismi Spoločenstva / (SL) Predmet navedene izjave

je v skladu z ustrezno usklajevalno zakonodajo Skupnosti / (FI) Edellä kuvattu vakuutuksen kohde on asiaa koskevan yhdenmukaistamista koskevan yhteisön lainsäädännön vaatimusten

mukainen / (SV) Föremålet för försäkran ovan överensstämmer med den relevanta harmoniserade gemenskapslagstiftningen

9 (EN) References to the relevant harmonised standards used or references to the technical specifications in relation to which conformity is declared / (BG) наименованията на

използваните хармонизирани стандарти или техническите спецификации, спрямо които се декларира съответствието / (ES) Referencias a las normas armonizadas pertinentes

utilizadas, o referencias a las especificaciones técnicas respecto a las cuales se declara la conformidad / (CS) Případné odkazy na příslušné harmonizované normy, které byly použity, nebo na

technické specifikace, na jejichž základě se shoda prohlašuje / (DA) Referencer til de relevante anvendte harmoniserede standarder eller referencer til de tekniske specifikationer, som der

erklæ res overensstemmelse med / (DE) Angabe der einschlägigen harmonisierten Normen, die zugrunde gelegt wurden, oder Angabe der technischen Spezifikationen, für die die Konformität

erklärt wird / (ET) Viited kasutatud asjakohastele ühtlustatud standarditele või viited tehnilistele spetsifikatsioonidele, millega seoses vastavust kinnitatakse / (EL) μνεία των σχετικών

εναρμονισμένων προτύπων που χρησιμοποιήθηκαν ή των τεχνικών προδιαγραφών με βάση τις οποίες δηλώνεται η συμμόρφωση / (FR) Références des normes harmonisées pertinentes

appliquées ou des spécifications techniques par rapport auxquelles la conformité est déclarée / (GA) Tagairtí do na caighdeáin chomhchuibhithe ábhartha a úsáidtear nó tagairtí do na

sonraíochtaí teicniúla i ndáil leis an gcomhréireacht a dhearbhaítear / (IT) Riferimenti alle pertinenti norme armonizzate utilizzate o riferimenti alle specifiche tecniche in relazione alle quali è

dichiarata la conformità / (LV) Norādes uz attiecīgajiem saskaņotajiem standartiem vai norādes uz tehniskām specifikācijām, attiecībā uz ko tiek deklarēta atbilstība / (LT) Taikytų darniųjų

standartų nuorodos arba techninių specifikacijų, pagal kurias buvo deklaruota atitiktis, nuorodos/ (HU) Adott esetben hivatkozás az alkalmazásra került vonatkozó harmonizált szabványokra,

illetőleg azokra a műszaki leírásokra, amelyekre nézve a megfelelésrol nyilatkoznak / (MT) Referenzi għall-istandards armonizzati rilevanti li ntużaw, jew referenzi għall-ispeċifikazzjonijiet li

b'relazzjoni għalihom qed tiġi ddikjarata l-konformità / (NL) Vermelding van de toegepaste geharmoniseerde normen of van de technische specificaties waarop de conformiteitsverklaring

betrekking heeft / (PL) Odwołania do odnośnych norm zharmonizowanych, które zastosowano, lub do specyfikacji technicznych, w odniesieniu do których deklarowana jest zgodność / (PT)

Referências às normas harmonizadas aplicáveis utilizadas ou às especificações técnicas em relação às quais é declarada a conformidade / (RO) Trimiteri la standardele armonizate relevante

folosite sau trimiteri la specificațiile tehnice în legătură cu care se declară conformitatea / (SK) Prípadné odkazy na príslušné použité harmonizované normy alebo odkazy na technické

špecifikácie, na základe ktorých sa vyhlasuje zhoda / (SL) Napotila na uporabljene usklajene standarde ali napotila na tehnične specifikacije za skladnost, ki so navedene na izjavi / (FI) Viittaus

niihin asiaankuuluviin yhdenmukaistettuihin standardeihin, joita on käytetty, tai viittaus teknisiin eritelmiin, joiden perusteella vaatimustenmukaisuusvakuutus on annettu / (SV) Hänvisningar till de

relevanta harmoniserade standarder som använts eller hänvisningar till de tekniska specifikationer enligt vilka överensstämmelsen försäkras

10 (EN) The notified body; performed; and issued the certificate / (BG) нотифицираният орган; извърши; и издаде сертификата / (ES) El organismo notificado; ha efectuado; y expide el

certificado / (CS) Oznámený subjekt; provedl; a vydal osvědčení / (DA) Det bemyndigede organ; der har foretaget; og udstedt attesten / (DE) Die notifizierte Stelle; hat; und folgende

Bescheinigung ausgestellt / (ET) Teavitatud asutus; teostas; ja andis välja tõendi / (EL) ο κοινοποιημένος οργανισμός ; πραγματοποίησε ; και εξέδωσε τη βεβαίωση / (FR) L'organisme notifié; a

effectué; et a établi l'attestation / (GA) Rinne an comhlacht dá dtugtar fógra ... agus d'eisigh sé an deimhniú/ (IT) l’organismo notificato; ha effettuato; e rilasciato il certificato / (LV) Pilnvarotā

iestāde; ir veikusi ; un izsniegusi sertifikātu / (LT) Notifikuotoji įstaiga; atliko; ir išdavė sertifikatą / (HU) A bejelentett szervezet; elvégezte a ; és a következő tanúsítványt adta ki / (MT) Il-korp

notifikat; wettaq; u ħareġ iċ-ċertifikat / (NL) De aangemelde instantie; heeft een; uitgevoerd en het certificaat verstrekt / (PL) jednostka notyfikowana; przeprowadziła; i wydała certyfikat / (PT) o

organismo notificado; efectuou; e emitiu o certificado / (RO) Organismul notificat ; a efectuat; și a emis certificatul / (SK) notifikovaný orgán; vykonal; a vydal osvedčenie / (SL) je priglašeni

organ; izvedel; in izdal certifikat / (FI) ilmoitettu laitos; suoritti; ja antoi todistuksen / (SV) Det anmälda organet ; har utfört ; och utfärdat intyget

11 (EN) Signed for and on behalf of / (BG) Подпис за или от името на / (ES) Firmado por y en nombre de / (CS) Podepsáno za a jménem / (DA) Underskrevet for og på vegne af / (DE)

Unterzeichnet für und im Namen von / (ET) (Kelle nimel ja poolt) alla kirjutatud / (EL) Υπογραφή για λογαριασμό και εξ ονόματος / (FR) Signé par et au nom de / (GA) Sínithe le haghaidh agus

thar ceann an / (IT) Firmato in vece e per conto di / (LV) Parakstīts / (LT) Už ką ir kieno vardu pasirašyta / (HU) Cégszerű aláírás / (MT) Iffirmata għal u f'isem / (NL) Ondertekend voor en

namens / (PL) Podpisano w imieniu / (PT) Assinado por e em nome de / (RO) Semnat pentru și în numele / (SK) Podpísané za a v mene / (SL) Podpisano za in v imenu /

(FI) puolesta allekirjoittanut / (SV) Undertecknat för

Annex (EN/ BG/ ES/ CS/ DA/ DE/ ET/ EL/ FR/ GA/ IT/ LV/ LT/ HU/ MT/ NL/ PL/ PT/ RO/ SK/ SL/ FI/ SV)

IC330_ENG

Documents

Transcript of IC330_ENG