Hydroclave The SIGN Meeting, New Delhi 29 th August 2001 Supported by the W.H.O. The Medical Waste...
-
Upload
celia-elswick -
Category
Documents
-
view
216 -
download
3
Transcript of Hydroclave The SIGN Meeting, New Delhi 29 th August 2001 Supported by the W.H.O. The Medical Waste...
Hydroclave
The SIGN Meeting, New Delhi29th August 2001
Supported by the W.H.O.
The Medical Waste Solution
Challenges we face today…
As the world population grows, and cities turn
into mega-cities, infectious disease controlbecomes critical.
Infectious diseases are traveling around the world as fast as an airplane can fly – and reach every corner of the globe.Government Regulators world-wide are responding to the problem with stringent new Environmental and Medical Waste Regulations.
Prescription to comply with new regulations.. Good waste segregation, to minimize Medical
Waste volume. Set up Centralized Treatment Facility , shared by a
number of Hospitals, or: Use in-house technology, which will turn Medical
Waste into ordinary non-regulated municipal waste.
Select a non-incineration technology, which Is easy and safe to operateHas no harmful emissionsSterilizes to a high level, at a low cost.
Why choose
Hydroclave Technology?
Performance• Guaranteed high level of
sterilization, including wet waste, metals, liquids and sharps.
• Automatic operation, and not dependent on operator skill for sterility.
• No infectious or harmful emissions.
• Mechanical destruction of the waste, and safe for land-fill.
Economic• Low operating cost with low
energy consumption.• Low maintenance costs.• No costly bags, filters or
chemicals in the process.• Very large weight and
volume reduction of the waste.
• Cost-effective purchase price with leasing/finance options.
• Strong warranty.
The Hydroclave Process – Stage oneMedical Waste is deposited in the Hydroclave vessel.
The Hydroclave can process:•Bagged waste, in ordinary bags•Sharps containers•Liquid containers•Cardboard containers•Metal objects
The Hydroclave Process – Stage two The waste fragmentation and sterilization
A. Powerful rotators mix the waste and breaks it into small pieces.
B. Steam fills the double wall (jacket) of the vessel and heats the vessel interior.
C. The liquids in the waste turn to steam.
D. After 20 minutes the waste and liquids are sterile.
The Hydroclave Process – Stage three Vessel venting and dehydration
A. The vent is opened, and the vessel de-pressurizes.
B. Steam heat and mixing continue until all the liquids are evaporated and the waste is dry.
The Hydroclave Process – Stage four Unloading the Waste
A. The unloading door is opened.
B. The mixer now rotates in the opposite direction, so angled blades on the mixer can push the waste out the unloading door.
C. The dry, sterile waste can be fine-shredded further or dropped in a waste disposal bin.
The waste is now ready for safe disposal!
The Hydroclave Result:Waste sterility of 6log10 guaranteed!
Dry waste, regardless of its
original water content.
Low odor, due to the
dryness.
Volume reduction to 85%
Weight reduction to 70%
Accepted as harmless
waste.
STERILIZATION OF NEEDLES & SHARPS
• The Hydroclave achieves a high degree of sterility due to a vigorous mixing and fragmenting of the waste inside the hot vessel:
– it breaks apart the sharps container …– sets free the sharps into the vessel …– where they are thoroughly exposed to the required temperature and
pressure.
• If for any reason temperature and pressure parameters are not met, the Hydroclave automatically resets and initiates a repeat sterilization cycle.
• It is IMPOSSIBLE for a needle or sharp to be shielded from the temperature as there are no “cold spots”, assuring total sterility.
• No bacterial growth was recorded on needles during tests conducted at the Kingston General Hospital.
Questions and Answers…..Q How does the Hydroclave achieve the high sterility? By a vigorous mixing and fragmenting of the waste inside the hot vessel.Q How does the Hydroclave make the waste very dry? By applying dry heat from the jacket to the waste, instead of injecting hot, wet steam into the waste. Q Is the Hydroclave approved for use? The Hydroclave is a steam sterilization technology, and accepted by authorities around the world. The CPCB called it “superior”Q Why is the Hydroclave inexpensive to operate? The steam is not lost – it is returned back to the boiler in the form of clean, hot water, ready for re-use.Q Is the Hydroclave a proven technology? Yes, it had been independently tested, and operating for years in North America, and around the world.Q Is there a Hydroclave Model to suit my needs? Most likely, because Hydroclave manufactures seven different sizes.
How does Hydroclave compare?
• Hydroclave
• No pre-shredding of infectious waste
• High level of sterility, to 8 log 10
• Low operating cost• (by steam)
• Microwave (non-pressure type)
• Must pre-shred• No sterility, only
“disinfection”• High operating cost• (expensive electricity)
How does Hydroclave compare?
• Hydroclave• Low operating cost by
recycling steam.
• No special bags required
• Treats wet or liquid loads easily
• Strong weight reduction
• Strong volume reduction
• Consistent high sterility
• Autoclave• Higher operating cost, no
steam recycling
• High temp. bags req’d
• Cannot treat wet or liquid loads
• Weight increase
• No volume reduction
• Spotty sterility
Proven Performance at Tata Memorial Hospital
When installed Sept./99 As it looks today, 2001
This unit ran 2,200 cycles, has treated 88,000 Kg of medical waste, and never failed a sterility test on any cycle.
Downtime was less than 1%, and maintenance cost minimal
Typical Hydroclave Centralized Facility
Enviromed Inc. in Canada collects waste from many Hospitals and operates The Hydroclave H-100
Recent Hydroclave Projects:
Dysa Tratamientos Ecologicos, Mexico
Waste was piled high trying to process same in a small, unsuitable microwave
Dysa replaced the microwave with anH-25 Hydroclave, which processes 2,000 Kg per day at their plant.
Dysa has bought their third Hydroclave, the latest one, the H-15, built in India.
Recent Hydroclave Projects
Vancouver, Canada.
Hydroclave won a major competition to supply The City of Vancouver with a Medical Waste Treatment Center.
The City’s decision was based on the environmental, technicaland economic superiority of the Hydroclave.
Two Hydroclave H-100 Systems will treat all the City’s Medical Waste.
Latest Hydroclave ProductMade in India by Hydroclave (India) Pvt Ltd.
The Model H-15. EXPORTED to Mexico City, Feb 2001
How Hydroclave can help: Prepare your waste profile analysis including waste volume and waste classifications.
Provide you with a cost/benefit analysis of installing the appropriate Hydroclave Model.
Supply a turn-key, fully operational Waste Treatment System with operating/maintenance training.
Registered Office:Hydroclave Systems (India) Pvt LtdCecil Court, M. Bhushan Road,Mumbai 400 039India
Tel: (22) 204-8082Fax: (22) 204-8083E-mail:[email protected]@vsnl.com
Hydroclave is a trade mark of Hydroclave Systems Corp.