Hydraulic ZD ISO VG 32

MATERIAL SAFETY DATA SHEET PRODUCT NAME : LIQTRO HYDRAULIC ZD 32 ISO VG 32 REV. 01ST FEBRUARY 2004

of 4

----------------------------------------------------------------------------- 1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION --------------------------------------------------------------------------------------------- PRODUCT DESCRIPTION: Hydraulic Lubricant, containing additives to improve the performance of lubricants and refined mineral base oil. COMPANY IDENTIFICATION: Smessindo Sakti Mandraguna

BLENDING PLANT and LABORATORY DIVISION Jln. Diponegoro KM 40 No. 62 Tambun-Bekasi 17510 Phone. 62-21 8808620 Fax. 62-21- 88354786

OFFICE Menara Era Building # 10-03 Jl. Raya Senen Kav. 135-137 Jakarta 10410 Phone. 62-21-3862426, Fax: 62-21-3863448

------------------------------------------------------------------------------- 2. HAZARDS IDENTIFICATION ------------------------------------------------------------------------------- HEALTH HAZARDS

• No significant effects expected ENVIRONMENTAL HAZARDS

• This preparation does not require classification on the basis of environmental hazard. PHYSICAL AND CHEMICAL HAZARDS / FIRE AND EXPLOSION HAZARDS

• Low hazard. Material can form flammable mixtures or can burn only upon heating to temperatures at or above the flash point.

This product does not contain any hazardous ingredient as the regulation from European Union Dangerous Substance / Preparation Directive. ------------------------------------------------------------------------------ 3. FIRST AID MEASURES ------------------------------------------------------------------------------- INHALATION :

• Not expected to be a problem in well-ventilated area. Using proper respiratory protection, immediately remove the affected from overexposure victim. Administer artificial respiration if breathing is stopped. Keep at rest. Call for prompt medical

attention. SKIN CONTACT :

• In case of frequent or prolonged contact, flush with large amounts of water; use soap if available.

EYE CONTACT : • Immediately flush eyes with large amounts of water for at least 15 minutes. Get prompt

medical attention. INGESTION :

• If swallowed, DO NOT induce vomiting. Keep at rest. Get prompt medical attention. If greater than 0.5 liter ingested, immediately give 1 or 2 glasses of water and call physician and hospital for assistance.


of 4

------------------------------------------------------------------------------- 4. FIRE-FIGHTING MEASURES ------------------------------------------------------------------------------- Fire Extinguisher : Carbon Dioxide, foam, dry chemical and water fog Fire Fighting Procedure :

• Use water spray to cool fire exposed surfaces and to protect personnel. • Use foam, dry chemical, or water spray to extinguish fire source.

SPECIAL FIRE PRECAUTIONS: • Respiratory and eye protection required for fire fighting personnel. • Avoid spraying water directly into storage containers due to danger of boil over. • Prevent runoff from fire or dilution from entering streams, sewers, or drinking water supply.

Special Protector Equipment : The fireman have to wear Self Contained Breathing Apparatus (SCBA) Explosion and another fire danger : Toxic Fumes Flash Point, o C : 231 (ASTM D-92) Flammable limits –LEL : none UEL : none NFPA Hazard ID : Health : 2, flammability : 1, Reactivity : 0 Hazardous Material Decomposition : Carbon Monoxide, Another Oxide ------------------------------------------------------------------------------- 5. SPILL AND LEAKAGE HANDLING ------------------------------------------------------------------------------- Procedure note : Report the spill happened according to system and procedure decided.

If the spill could be enter the aqueduct or river, please report to authority officer as soon as possible.

Leakage and Spill Procedure : Absorb the spill by saw-dust, clay, and another fire resistant material. Clean up and discard to the location that have been decided.

Prevention on Environment : Prevent the spill entering the gutter, waste canal, and into the soil. ------------------------------------------------------------------------------- 6. HANDLING AND STORAGE ------------------------------------------------------------------------------- STORAGE TEMPERATURE (Deg C) : 60.0 Maximum TRANSPORT TEMPERATURE (Deg C) : 60.0 Maximum LOADING/UNLOADING TEMPERATURE (Deg C) : 60.0 Maximum STORAGE/TRANSPORT PRESSURE (k Pa) : Atmospheric STORAGE / HANDLING, GENERAL NOTES :

• Keep container closed. Handle containers with care. Open slowly in order to control possible pressure release. Store in a cool, well-ventilated place away from incompatible materials.

• DO NOT handle, store or open near an open flame, sources of heat or sources of ignition. Protect material from direct sunlight.

• DO NOT pressurize, cut, heat, or weld containers. Empty product containers may contain product residue. DO NOT reuse empty containers without commercial cleaning or reconditioning.

------------------------------------------------------------------------------- 7. EXPOSURE CONTROL / SELF PROTECTION ------------------------------------------------------------------------------- Ventilation : Commonly there is no special regulation for ventilation on normal condition Breath Protection : There is no special regulation on normal condition. Eye Protection : Use eye protection equipment. Skin Protection : Regulation for personnel hygiene still have to give a notice. Use the nitrile gloves, long

arm shirt, boots. Don’t use ring or watch because it can make skin reaction. Exposure limit : This product doesn’t contain any material that have been known have exposure limit

value. But we can use exposure limit value (OSHA PEL) from the vapor, i.e 5.00 mg/m3

and ACGIH STEL, i.e. 10 mg/m3.


of 4

------------------------------------------------------------------------------- 8. PHYSICAL AND CHEMICAL PROPERTIES ------------------------------------------------------------------------------- These are indicative values only. Please refer also to the product specification sheet.

Property LIQTRO HYDRAULIC ZD 32 Physical State Liquid Color (ASTM D 1500) L 0.5 Odor Mild hydrocarbon Boiling Point > 316 Deg C Typical Flash Point (COC, ASTM D 92) > 200 Deg C Minimum Material Hygroscopic No Density (15 Deg C, ASTM D 4052) 0.8739 g/cm3 Viscosity at 400 C (ASTM D 445) 31.47 cSt Viscosity at 1000 C (ASTM D 445) 5.44 cSt Viscosity Index (ASTM D 2270) 108 Foaming Tendency/stability (ASTM D 892) Seq. I Seq. II Seq. III

0/0 ml

10/0 ml 0/0 ml

Water Separability ( 54 Deg C, ASTM D 1401)

40-40-0 (20 minutes)

------------------------------------------------------------------------------- 9. STABILITY AND REACTIVITY ------------------------------------------------------------------------------- HAZARDOUS POLYMERIZATION : No STABILITY (THERMAL, LIGHT, ETC) : Stable CONDITION TO AVOID : Extreme Heat MATERIALS AND CONDITIONS TO AVOID (INCOMPATIBILITY) : Strong oxidizing agents. ------------------------------------------------------------------------------- 10. TOXICOLOGICAL INFORMATION ------------------------------------------------------------------------------- INHALATION :

• Negligible hazard at ambient (-20 to 60 Deg C) or recommended blending temperature. WARNING :

• Repeated and prolonged overexposure to oil mists may result in droplet deposition, oil granuloma formation, inflammation and increased incidence of infection.

SKIN CONTACT : • Low order of toxicity. • Frequent or prolonged contact may cause mild skin discomfort.

EYE CONTACT : • mild irritation. If not removed promptly, will injure eye tissue,

which may result in permanent damage. INGESTION :

• Minimal toxicity. ------------------------------------------------------------------------------ 11. ECOLOGY INFORMATION ------------------------------------------------------------------------------- Impact and damage on environment : Non-toxic---- based on testing of similar material and component.


of 4

------------------------------------------------------------------------------- 12. DISPOSAL CONSIDERATIONS -------------------------------------------------------------------------------

• This product is NOT suitable for disposal by either landfill or via municipal sewers, drains, natural streams or rivers.

• This product will generate an ash if burned. • It can be burned directly in appropriate equipment.

------------------------------------------------------------------------------ 13. REGULATION INFORMATION -------------------------------------------------------------------------------

based on U.S. Superfund Amendment and Reauthorization Act (SARA) this product doesn’t contain EXTREMLY HAZARDOUS more than 1%

Additional information is available on special request ---------------------------------------------------------------

Hydraulic ZD ISO VG 32

Technology

Transcript of Hydraulic ZD ISO VG 32