HUEDA™ RF Receiver/Controller HUEDA LED · RGB/W LED Strip RGB/W LED Strip RGB/W LED Strip RF...

HUEDA™ RF Receiver/Controller

1/4

Model: H-R009PD

Ÿ This product is intended to be installed and serviced by a qualied licensed electrician. Install in accordance with the National Electric Code, and local regulations. Disconnect power before installing or servicing. Only power with a

regulated (listed) constant voltage Class 2 power supply (12-24V DC). Never use this product with dimmable or magnetic dimmable power source(driver).

Ÿ Ensure applicable wire is installed between driver, xture, and any controls in between. When choosing wire, factor in voltage drop, amperage rating and type (in-wall rated, wet location rated, etc.). Inadequate wire installation could overheat wires and cause re.

Ÿ This product is rated for indoor installation and can be used for dry locations. Avoid the direct sun light. Ÿ Do not modify this product beyond the instructions in this guide or the warranty will be voided.Ÿ Wiring diagrams in this installation guide for basic installations. Please carefully review your installation before

proceeding.Ÿ Always be sure to mount this unit in an area with proper ventilation to avoid overheating.Ÿ Please check if the output voltage of any LED power supplies used comply with the working voltage of the product.Ÿ Never connect any cables while power is on and always assure correct connections to avoid short circuits before

switching on.Ÿ Please ensure that the cable is secured tightly in the connectorŸ For updated information please consult your supplier.

Safety & Warnings

Before you begin, read all warnings and installation instructions (as they may have been updated from previous versions ). Improper installation(s) present hazards, which can result in personal injury or property damage.

Warning: Input voltage must be identical to output voltage

of the LED Fixture!

Exposed wire should not be more than 6- 8 mm long tinned. Do not allow Wires to cross and insure all exposed wire is fully inserted into the terminals. Use 22 to 16 AWG gauge wire for output terminals.

WIRE 6-8MM (0.25-0.30”)

1. Product Operation Overview:

R

G

B

W

LE

D

PRI:

Uin=12-36VDC

Iin=20.5A

SEC:

Uout=4x(12-36)VDC

Iout=4x5A

Pout=4x(60-180)W

LED CONTROLLER

H-R009PD

Learning Key

Re

pe

ate

r Sig

na

l

Receiver RepeaterJumper

Learning Button Power Input (12/24VDC)

RGBW LED Light Output

+

RG

B

W

V+

V+

V-

V-

Data In/Out

GND

Data+ In

Data- In

Data+ OutData- Out

2. Product Parameters:

Part No.

Input Voltage

Current

Output

H-R009PD

12V~36V DC

4 x 5A

4 x (60-180)W

HUEDA™ LED | CALGARY, AB | CANADA

Copyright © 2015 HUEDA™ LED, A division of LED World Inc.. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).

HUEDA LEDwww.huedaled.com

2/4

Model: H-R009PD

Note: Each hand remote controls 4 zones (areas) and with each zone one can have a maximum of 8 wireless receivers. Each receiver can be controlled by 8 different remote controllers. If more than 8 receivers are required in one zone, then please refer to section 5.2 “optional wiring diagram for direct wire and wireless connections”.

f. The Connected LED light will blink to confirm zone designation and corresponding color will light

Press at learning button on receiver over 5 seconds until LED light flash, unpairs the receiver.

d. Press desired zone button on remote control, then touch color wheel on

remote control .

3.1 Pairing Guide:

b. Turn ON handheld remote control.

c. Press learning button on receiver.

a. Wire according to connection diagram

4. Product Dimension:

156mm (6.14”)

166mm (6.53”)

53

.4m

m (

2.1

0”)

23mm (0.90”)

3.2 Reset/Unpairing Guide:





3/4

Model: H-R009PD

Receiver Repeater One receiver can connect multiple repeaters of under 100m (328ft) usingCAT5 wire.

Receiver/Repeater setting jumper

Receiver 1

+

R

G

B

W

LE

D

PRI:

Uin=12-36VDC

Iin=20.5A

SEC:

Uout=4x(12-36)VDC

Iout=4x5A

Pout=4x(60-180)W

LED CONTROLLER

H-R009PD

Learning Key

Re

pe

ate

r Sig

na

l

Class 2 RegulatedPower Supply

12-24VDCL

N110V-230VAC

Receiver 2 (Repeater)

R

G

B

W

LE

D

PRI:

Uin=12-36VDC

Iin=20.5A

SEC:

Uout=4x(12-36)VDC

Iout=4x5A

Pout=4x(60-180)W

LED CONTROLLER

H-R009PD

Learning Key

Re

pe

ate

r Sig

na

l

Receiver 3 (Repeater)

R

G

B

W

LE

D

PRI:

Uin=12-36VDC

Iin=20.5A

SEC:

Uout=4x(12-36)VDC

Iout=4x5A

Pout=4x(60-180)W

LED CONTROLLER

H-R009PD

Learning Key

Re

pe

ate

r Sig

na

l

Receiver Repeater

Receiver Repeater

Receiver Repeater

W

W

W

RGB/W LED Strip

RGB/W LED Strip

RGB/W LED Strip

RF remote H-2819S(Optional)

5.2 Optional Wiring Diagram for direct wire and wireless connections

[V+]

[V-]

V+

V-

R

G

B

W

V-

V+

+

R

G

B

W

Po

we

r In

pu

tR

GB

W O

utp

ut

CAT5 Cable

5.1 Wiring Diagram:Output V+ is common anode for RGBW LED

Receiver

R

G

B

W

LE

D

PRI:

Uin=12-36VDC

Iin=20.5A

SEC:

Uout=4x(12-36)VDC

Iout=4x5A

Pout=4x(60-180)W

LED CONTROLLER

H-R009PD

Learning Key

Re

pe

ate

r Sig

na

l

Class 2 Regulated Power Supply

12-24VDCL

N

110V-230VAC

Receiver Repeater

W

RGB/W LED Strip

RF remote H-2819S(Optional)

[V+]

[V-]

[W][B]

[G][R]

[+]

R

G

B

W

V+

V-

V-

V+

+

R

G

B

W

Po

we

r In

pu

tR

GB

W O

utp

ut

+ -

Make sure thatwires cannot

cross

+ -

Make sure thatwires are fully inserted

wrong correct

Note: Verify with a pull on the wire to test if wire is securely connected

Receiver 1 is connected wirelessly with RF remote

Receiver 2 is in slave mode connected by wire

Receiver 3 is in slave mode connected by wire

Note: Jumper should be in receiver mode(default is receiver mode)

Note: Jumper is in receiver mode

Note: Jumper

is in repeatermode

+Securely mount withscrew to surface

AC Power50/60HzG

N

L

V+

V-

Class 2 Regulated Driver (12~24VDC)

AC Power50/60HzG

N

L

V+

V-

Class 2 Regulated Driver (12~24VDC)

(Red Wire)

(Black Wire)

(Red Wire)

(Black Wire)

(Red Wire)

(Black Wire)

D1+

+

R

G

B

W

Sig

na

l Ou

t

D1-

D2+

D2-

Sig

na

l In


Use this method if the distance of the controller (ex. hand remote) is farther than 75 ft to the RF Color Receiver (H-R009PD)

Wire Color may vary, usually Black wire




Model: H-R009PD

4/4

HUEDA™ (LW-2814DMX)

HUEDA™ Hub(H-2818WIN)

5CH DMX Decoder(H-DMX2108A-5M-3)

RF RGBW Receiver (Outdoor)

(H-R009FA(W))

RGBW Handheld Remote(H-2819S)

RF RGBW Receiver(H-R009PD)

Easy DMX512 Decoder(H-2102B(W))

Master Color Controller

Controllers/Receivers

6. Compatible Master Color Controllers and Controllers/Receivers

*Requires HUEDA™ Hub (H-2818WIN) to use mobile app

*Requires HUEDA™ Hub (H-2818WIN) to use mobile app

IOS app available IOS app available

Federal Communications Commission (FCC) Statement

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation.

Note: The manufactures is not responsible for any radio or tv interference caused by unauthorized modications to this equipment. Such modications will void the user's authority to operate the equipment and warranty.

THREE YEAR LIMITED LIGHTING WARRANTYLED WORLD INC. warranties this product for three year (some exceptions may apply) from the date of shipping unless otherwise noted in writing. This warranty is expressly in lieu of all other warranties expressed or implied. Under this Limited Warranty, the obligation of the company is limited to replacing on a prorated basis, at its option, any component found to be defective. This Limited Warranty does not apply to damage caused by buyer or alteration to the product or incorrect power supply. Factory warrantees are covered by the original manufacturer and claims must be submitted to them. Use only with LED World’s regulated class 2 power supply.

LED World Inc. And its providers will never be liable to you or any other person for any indirect, incidental, consequential, special, punitive or exemplary loss or damage arising from, connected with, the purchase of products, including but not limited to loss of data, business, markets, cost of labour, savings, income, profits, use, production, reputation or goodwill, anticipated or otherwise, or economic loss, under any theory of liability (whether in contract, tort, strict liability or any other theory or law or equity), regardless of any negligence or other fault or wrongdoing (including without limitation gross negligence and fundamental breach) by led world inc. Or any person for whom led world inc. Is responsible, and even if led world inc. Has been advised of the possibility of such loss or damage being incurred.

If a product is defective, we will replace the product with similar or identical product or at our option a credit towards a future purchase. To make a claim under this warranty, obtain a return authorization number.





HUEDA™ RF Receiver/Controller HUEDA LED · RGB/W LED Strip RGB/W LED Strip RGB/W LED Strip RF...

Documents

Transcript of HUEDA™ RF Receiver/Controller HUEDA LED · RGB/W LED Strip RGB/W LED Strip RGB/W LED Strip RF...