Huawei switch how to - implementing inter-vlan communication using VLANIF interfaces

10
HUAWEI QUIDWAY S5700 HOW-TO IMPLEMENTING INTER-VLAN COMMUNICATION USING VLANIF INTERFACES www.ipmax.it

description

Huawei S5700 Layer 3 switch can replace a router to implement communication between VLANs using VLANIF interfaces. Stay with us!

Transcript of Huawei switch how to - implementing inter-vlan communication using VLANIF interfaces

Page 1: Huawei switch how to - implementing inter-vlan communication using VLANIF interfaces

HUAWEI QUIDWAY S5700 HOW-TOI M P L E M E N T I N G I N T E R -V L A N CO M M U N I C AT I O N U S I N G V L A N I F

I N T E R FAC E Swww.ipmax.it

Page 2: Huawei switch how to - implementing inter-vlan communication using VLANIF interfaces

GENERAL INFOS AND APPLICATIONENVIRONMENT

S5700 Layer 3 switch can replace a router to implement communication between VLANs using VLANIF interfaces. Describing this brief procedure we will assume that departments of an enterprise are located on different network segments and use the same services, such as Internet access and VoIP. The departments are in different VLANs, so inter-VLAN communication must be implemented.In this semplified network environment, as shown in the picture, Department 1 and Department 2 use the same service, but they belong to different VLANs (vlan 10 and vlan 20) and network segments. Users in Department 1 and Department 2 need to communicate with each other.

SwitchA

SwitchB

Page 3: Huawei switch how to - implementing inter-vlan communication using VLANIF interfaces

CREATING VLANS ON THE SWITCHES FOR DIFFERENT DEPARTMENTS

<SwitchB> system-view

[SwitchB] vlan batch 10 20

1. Create vlans on SwitchBEnter the configuration view

Create vlan 10 and vlan 20

2. Create vlans on SwitchA

<SwitchA> system-view

[SwitchA] vlan batch 10 20

Enter the configuration view

Create vlan 10 and vlan 20

Page 4: Huawei switch how to - implementing inter-vlan communication using VLANIF interfaces

ADDING LAYER 2 INTERFACES TO THE VLANS (1)

3. Add layer 2 interfaces to vlans of SwitchB

[SwitchB] interface gigabitethernet 0/0/1[SwitchB-GigabitEthernet0/0/1] port link-type trunk[SwitchB-GigabitEthernet0/0/1] port trunk allow-passvlan 10 20[SwitchB-GigabitEthernet0/0/1] quit

Enter the interfaceview

Configure the porttype

Configure the vlans for the port

Exit the interfaceview

Page 5: Huawei switch how to - implementing inter-vlan communication using VLANIF interfaces

ADDING LAYER 2 INTERFACES TO THE VLANS (2)

[SwitchA] interface gigabitethernet 0/0/1

[SwitchA-GigabitEthernet0/0/1] port link-type trunk

[SwitchA-GigabitEthernet0/0/1] port trunk allow-pass vlan10 20

[SwitchA-GigabitEthernet0/0/1] quit

[SwitchA] interface gigabitethernet 0/0/2

[SwitchA-GigabitEthernet0/0/2] port link-type access

[SwitchA-GigabitEthernet0/0/2] port default vlan 10

[SwitchA-GigabitEthernet0/0/2] quit

[SwitchA] interface gigabitethernet 0/0/3

[SwitchA-GigabitEthernet0/0/3] port link-type access

[SwitchA-GigabitEthernet0/0/3] port default vlan 20

[SwitchA-GigabitEthernet0/0/3] quit

4. Add layer 2 interfaces to vlans of SwitchA

Enter the interface view

Configure the port type

Configure the vlans for the port

Exit the interface view

Page 6: Huawei switch how to - implementing inter-vlan communication using VLANIF interfaces

CREATING VLANIF INTERFACES AND CONFIGURING IP ADDRESSES ON LAYER 3 SWITCH (SWITCHB)

5. Create vlanif interfaces and assign IP address on SwitchB

[SwitchB] interface vlanif 10

[SwitchB-Vlanif10] ip address 10.10.10.1 24

[SwitchB-Vlanif10] quit

[SwitchB] interface vlanif 20

[SwitchB-Vlanif20] ip address 20.20.20.1 24

[SwitchB-Vlanif20] quit

Create the vlanif and enter the vlanif view

Exit the vlanif view

Assign the IP address to the vlanif

Page 7: Huawei switch how to - implementing inter-vlan communication using VLANIF interfaces

CHECKING THE CONFIGURATION6. Check the configuration on SwitchB

[SwitchB] display current configuration#sysname SwitchB

#vlan batch 10 20

#interface Vlanif10ip address 10.10.10.1 255.255.255.0

#interface Vlanif20ip address 20.20.20.1 255.255.255.0

#interface GigabitEthernet0/0/1port link-type trunkport trunk allow-pass vlan 10 20

#return

Page 8: Huawei switch how to - implementing inter-vlan communication using VLANIF interfaces

CHECKING THE CONFIGURATION7. Check the configuration on SwitchA

[SwitchA] display current configuration#sysname SwitchA#vlan batch 10 20#interface GigabitEthernet0/0/1port link-type trunkport trunk allow-pass vlan 10 20#interface GigabitEthernet0/0/2port link-type accessport default vlan 10#interface GigabitEthernet0/0/3port link-type accessport default vlan 20#return

Page 9: Huawei switch how to - implementing inter-vlan communication using VLANIF interfaces

MORE NEEDS?

See hints on www.ipmax.itOr email us your questions to [email protected]

You can buy our Remote Support assistance (1h, 4hs or 8hs pack) via PAYPALby using your Teamviewer account.Contact us for any info!

Page 10: Huawei switch how to - implementing inter-vlan communication using VLANIF interfaces

IPMAX

IPMAX is a Huawei GOLD Partner in Italy.IPMAX is the ideal partner for companies seeking quality in products and services. IPMAX guarantees method and professionalism to support its customers in selecting technologies with the best quality / price ratio, in the design, installation, commissioning and operation.

IPMAX srlVia Ponchielli, 420063 Cernusco sul Naviglio (MI) – Italy+39 02 9290 9171