HTXD6i-STXD6i Setup-Adjust-Cal Manual rev 2
Transcript of HTXD6i-STXD6i Setup-Adjust-Cal Manual rev 2
SETUP, ADJUSTMENTS AND CALIBRATIONS
THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.
To find the latest revision of this publication, visit our website at:
www.multiquip.com
SERIES
MODEL HTXD6i/STXD6iHYDRAULIC RIDE-ON TROWEL
(YANMAR 4TNV84T-Z-DSA2 DIESEL ENGINE)
Revision #2 (04/09/14)
PN: 32399
PAGE 2 — HTXD6i/STXD6i TROWEL • SETUP, ADJUSTMENTS AND CALIBRATIONS — REV. #2 (04/09/14)
TABLE OF CONTENTS
HTX6Di/STX6Di TrowelMachine Information And Maintenance Log ............ 3Safety Information ................................................ 4-9Tools Needed ......................................................... 10Machine Information .............................................. 11
Model .................................................................. 11Serial Number .................................................... 11Program ID ......................................................... 11
General Procedures .............................................. 12Setup Jumper Installation ................................... 12Remove Setup Jumper (If Installed). .................. 12
Initial Check And Adjustments .......................... 13-14Preliminary Charge Pressure Adjustment ......... 13Oil And Coolant Check ....................................... 13
Hydraulic Oil Check ......................................... 13Engine Oil ....................................................... 13Engine Coolant ................................................ 14
Service Tool Setup And Connection ................. 15-16Whiteman Service Tool (WST) Installation ......... 15
Laptop Configuration ............................................. 17Connection Procedure ........................................ 17
Machine Setup And Calibration ........................ 18-27Calibrate Foot Pedal ........................................... 18
Calibration ....................................................... 19
Secondary Hydraulic Fill Procedures ................. 19Machine Pressure Adjustment............................ 20
Charge Pressure Adjustment ......................... 20Pitch Pressure Check ...................................... 20Pitch Pressure Adjustment .............................. 21Steering Pressure Adjustment ......................... 21
Trowel Speed Adjustment\Setup ....................... 22Adjust Zero Stroke Position ............................. 22Left Side Trowel Speed Adjustment ................. 22Right Side Trowel Speed Adjustment ............... 23Calibrate Stroke Sensor .................................. 23
Pitch Setup ......................................................... 24Flatten Blades ................................................ 24Measure Blade Leading Edge Height .............. 25Leading Edge Height Adjustment ................... 25Set Zero Pitch Cylinder Stops ......................... 26Pitch Sensor Calibration .................................. 26
Inspection ......................................................... 28-29Fluid Levels ........................................................ 28Mechanical ......................................................... 28Static Blade Pitch Drift Test ................................ 29
Fuse Information .................................................... 30
HTXD6i/STXD6i TROWEL • SETUP, ADJUSTMENTS AND CALIBRATIONS — REV. #2 (04/09/14) — PAGE 3
MACHINE INFORMATION AND MAINTENANCE LOG
Technician__________________________________e Date:___________________________
Machine InformationMODEL LH Motor Serial No.
Machine Serial No. RH Motor Serial No.
Engine Serial No. Program ID
Pump Serial No. Program Version
InspectionFuel Levels ü Leak Checks ü
Engine Oil Engine
Coolant Coolant
Hydraulic Oil Hydraulics
Mechanical ü Functional Checks ü
Grease Points Hour Meter
Stabilizer Rings Seat Switch
Hydraulics Drift Test
Retardant Spray System Travel (Start/Stop)
Electrical ü Initial Height (LH/RH)
Cooling Fan Final Height (LH/RH)
Switches
Lights and Indicators
Machine Setup and Calibration InformationHydraulic Pressure Settings (Hydraulic Oil Temperature Below 125 °F) Calibration Point 1 Point 2
Charge Pressure (psi) Foot Pedal
Pitch Pressure (psi) Stroke Sensor
Steering Pressure (psi) Pitch Sensors
Blade Speed Travel (LH)
Left (rpm) Travel (RH)
Right (rpm) Stops (LH)
Stops (RH)
PAGE 4 — HTXD6i/STXD6i TROWEL • SETUP, ADJUSTMENTS AND CALIBRATIONS — REV. #2 (04/09/14)
Do not operate or service the equipment before reading the entire manual. Safety precautions should be followed at all times when operating this equipment. Failure to read and understand the safety messages and operating instructions could result in injury to yourself and others.
SAFETY MESSAGES
The four safety messages shown below will inform you about potential hazards that could injure you or others. The safety messages specifi cally address the level of exposure to the operator and are preceded by one of four words: DANGER, WARNING, CAUTION or NOTICE.
SAFETY SYMBOLS
DANGER
Indicates a hazardous situation which, if not avoided, WILL result in DEATH or SERIOUS INJURY.
WARNING
Indicates a hazardous situation which, if not avoided, COULD result in DEATH or SERIOUS INJURY.
CAUTION
Indicates a hazardous situation which, if not avoided, COULD result in MINOR or MODERATE INJURY.
NOTICE
Addresses practices not related to personal injury.
Potential hazards associated with the operation of this equipment will be referenced with hazard symbols which may appear throughout this manual in conjunction with safety messages.
Lethal exhaust gas hazards
Explosive fuel hazards
Burn hazards
Rotating parts hazards
Symbol Safety Hazard
Pressurized fluid hazards
Hydraulic fluid hazards
SAFETY INFORMATION
HTXD6i/STXD6i TROWEL • SETUP, ADJUSTMENTS AND CALIBRATIONS — REV. #2 (04/09/14) — PAGE 5
GENERAL SAFETY
CAUTION
�NEVER operate this equipment without proper protective clothing, shatterproof glasses, respiratory protection, hearing protection, steel-toed boots and other protective devices required by the job or city and state regulations.
�Avoid wearing jewelry or loose fi tting clothes that may snag on the controls or moving parts as this can cause serious injury.
�NEVER operate this equipment when not feeling well due to fatigue, illness or when under medication.
�NEVER operate this equipment under the infl uence of drugs or alcohol.
�ALWAYS clear the work area of any debris, tools, etc. that would constitute a hazard while the equipment is in operation.
�No one other than the operator is to be in the working area when the equipment is in operation.
�DO NOT use the equipment for any purpose other than its intended purposes or applications.
NOTICE
� This equipment should only be operated by trained and qualifi ed personnel 18 years of age and older.
�Whenever necessary, replace nameplate, operation and safety decals when they become diffi cult read.
�Manufacturer does not assume responsibility for any accident due to equipment modifi cations. Unauthorized equipment modifi cation will void all warranties.
�NEVER use accessories or attachments that are not recommended by Multiquip for this equipment. Damage to the equipment and/or injury to user may result.
�ALWAYS know the location of the nearest fi re extinguisher.
�ALWAYS know the location of the nearest fi rst aid kit.
�ALWAYS know the location of the nearest phone or keep a phone on the job site. Also, know the phone numbers of the nearest ambulance, doctor and fi re department. This information will be invaluable in the case of an emergency.
SAFETY INFORMATION
PAGE 6 — HTXD6i/STXD6i TROWEL • SETUP, ADJUSTMENTS AND CALIBRATIONS — REV. #2 (04/09/14)
TROWEL SAFETY
DANGER
�Engine fuel exhaust gases contain poisonous carbon monoxide. This gas is colorless and odorless, and can cause death if inhaled.
� The engine of this equipment requires an adequate free fl ow of cooling air. NEVER operate this equipment in any enclosed or narrow area where free fl ow of the air is restricted. If the air fl ow is restricted it will cause injury to people and property and ser ious damage to the equipment or engine.
�NEVER operate the equipment in an explosive atmosphere or near combustible materials. An explosion or fi re could result causing severe bodily harm or even death.
WARNING
� If applicable, NEVER use your hand to fi nd hydraulic leaks. Use a piece of wood or cardboard. Hydraulic fl uid injected into the skin must be treated by a knowledgable physician immediately or severe injury or death can occur.
�ALWAYS keep clear of rotating or moving parts while operating the trowel.
�NEVER disconnect any emergency or safety devices. These devices are intended for operator safety. Disconnection of these devices can cause severe injury, bodily harm or even death. Disconnection of any of these devices will void all warranties.
CAUTION
�NEVER allow passengers or riders on the trowel during operation.
�NEVER lubricate components or attempt service on a running machine.
�NEVER place your feet or hands inside the guard rings while starting or operating this equipment.
DANGEROUS
GAS FUMES
NOTICE
�ALWAYS keep the machine in proper running condition.
� Fix damage to machine and replace any broken parts immediately.
�ALWAYS store equipment properly when it is not being used. Equipment should be stored in a clean, dry location out of the reach of children and unauthorized personnel.
�A safety manual for operating and maintenance personnel of concrete power trowels produced by the Association of Equipment Manufacturers (AEM) can be obtained for a fee by ordering through their website at www.aem.org.
Order FORM PT-160
ENGINE SAFETY
WARNING
�DO NOT place hands or fingers inside engine compartment when engine is running.
�NEVER operate the engine with heat shields or guards removed.
�Keep fi ngers, hands hair and clothing away from all moving parts to prevent injury.
�DO NOT remove the radiator cap while the engine is hot. High pressure boiling water will gush out of the radiator and severely scald any persons in the general area of the trowel.
�DO NOT remove the coolant drain plug while the engine is hot. Hot coolant will gush out of the coolant tank and severely scald any persons in the general area of the trowel.
�DO NOT remove the engine oil drain plug while the engine is hot. Hot oil will gush out of the oil tank and severely scald any persons in the general area of the trowel.
CAUTION
�NEVER touch the hot exhaust manifold, muffl er or cylinder. Allow these parts to cool before servicing equipment.
SAFETY INFORMATION
HTXD6i/STXD6i TROWEL • SETUP, ADJUSTMENTS AND CALIBRATIONS — REV. #2 (04/09/14) — PAGE 7
NOTICE
�NEVER run engine without an air fi lter or with a dirty air fi lter. Severe engine damage may occur. Service air fi lter frequently to prevent engine malfunction.
�NEVER tamper with the factory settings of the engine or engine governor. Damage to the engine or equipment can result if operating in speed ranges above the maximum allowable.
FUEL SAFETY
DANGER
�DO NOT start the engine near spilled fuel or combustible fl uids. Fuel is extremely fl ammable and its vapors can cause an explosion if ignited.
�ALWAYS refuel in a well-ventilated area, away from sparks and open fl ames.
�ALWAYS use extreme caution when working with fl ammable liquids.
�DO NOT fi ll the fuel tank while the engine is running or hot.
�DO NOT overfi ll tank, since spilled fuel could ignite if it comes into contact with hot engine parts or sparks from the ignition system.
�Store fuel in appropriate containers, in well-ventilated areas and away from sparks and fl ames.
�NEVER use fuel as a cleaning agent.
�DO NOT smoke around or near the equipment. Fire or explosion could result from fuel vapors or if fuel is spilled on a hot engine.
BATTERY SAFETY
DANGER
�DO NOT drop the battery. There is a possibility that the battery will explode.
�DO NOT expose the battery to open fl ames, sparks, cigarettes, etc. The battery contains combustible gases and liquids. If these gases and liquids come into contact with a fl ame or spark, an explosion could occur.
WARNING
�ALWAYS wear safety glasses when handling the battery to avoid eye irritation. The battery contains acids that can cause injury to the eyes and skin.
�Use well-insulated gloves when picking up the battery.
�ALWAYS keep the battery charged. If the battery is not charged, combustible gas will build up.
�DO NOT charge battery if frozen. Battery can explode. When frozen, warm the battery to at least 61°F (16°C).
�ALWAYS recharge the battery in a well-ventilated environment to avoid the risk of a dangerous concentration of combustible gases.
� If the battery liquid (dilute sulfuric acid) comes into contact with clothing or skin, rinse skin or clothing immediately with plenty of water.
� If the battery liquid (dilute sulfuric acid) comes into contact with eyes, rinse eyes immediately with plenty of water and contact the nearest doctor or hospital to seek medical attention.
CAUTION
�ALWAYS disconnect the NEGATIVE battery terminal before performing service on the equipment.
�ALWAYS keep battery cables in good working condition. Repair or replace all worn cables.
SAFETY INFORMATION
PAGE 8 — HTXD6i/STXD6i TROWEL • SETUP, ADJUSTMENTS AND CALIBRATIONS — REV. #2 (04/09/14)
TRANSPORTING SAFETY
CAUTION
�NEVER allow any person or animal to stand underneath the equipment while lifting.
�Ride-on trowels are very heavy and awkward to move around. Use proper heavy lifting procedures and DO NOT attempt to lift the trowel by the guard rings.
NOTICE
� The easiest way to lift the trowel is to utilize the lift loops that are welded to the frame. These lift loops are located to the left and right sides of the operator’s seat.
A strap or chain can be attached to these lift loops, allowing a forklift or crane to lift the trowel up onto and off of a slab of concrete. The strap or chain should have a minimum of 2,000 pounds (1,000 kg) lifting capacity and the lifting gear must be capable of lifting at least this amount.
�NEVER transport trowel with fl oat pans attached unless safety catches are used and are specifi cally cleared for such transport by the manufacturer.
�NEVER hoist the trowel more than three feet off the ground with fl oat pans attached.
�Before lifting, make sure that the lift loops are not damaged.
�Always make sure crane or lifting device has been properly secured to the lift loops of the equipment.
�ALWAYS shutdown engine before transporting.
�NEVER lift the equipment while the engine is running.
� Tighten fuel tank cap securely and close fuel cock to prevent fuel from spilling.
�Use adequate lifting cable (wire or rope) of suffi cient strength.
�DO NOT lift machine to unnecessary heights.
�ALWAYS tie down equipment during transport by securing the equipment with rope.
TOWING SAFETY
CAUTION
�Check with your local county or state safety towing regulations, in addition to meeting Department of Transportation (DOT) Safety Towing Regulations, before towing your trowel.
� In order to reduce the possibility of an accident while transporting the trowel on public roads, ALWAYS make sure the trailer that supports the trowel and the towing vehicle are mechanically sound and in good operating condition.
� ALWAYS shutdown engine before transporting
�Make sure the hitch and coupling of the towing vehicle are rated equal to, or greater than the trailer “gross vehicle weight rating.”
�ALWAYS inspect the hitch and coupling for wear. NEVER tow a trailer with defective hitches, couplings, chains, etc.
�Check the tire air pressure on both towing vehicle and trailer. Trailer tires should be infl ated to 50 psi cold. Also check the tire tread wear on both vehicles.
�ALWAYS make sure the trailer is equipped with a safety chain.
�ALWAYS properly attach trailer’s safety chains to towing vehicle.
�ALWAYS make sure the vehicle and trailer directional, backup, brake and trailer lights are connected and working properly.
�DOT Requirements include the following:
• Connect and test electric brake operation.
• Secure portable power cables in cable tray with tie wraps.
� The maximum speed for highway towing is 55 MPH unless posted otherwise. Recommended off-road towing is not to exceed 15 MPH or less depending on type of terrain.
�Avoid sudden stops and starts. This can cause skidding, or jack-knifi ng. Smooth, gradual starts and stops will improve towing.
�Avoid sharp turns to prevent rolling.
SAFETY INFORMATION
HTXD6i/STXD6i TROWEL • SETUP, ADJUSTMENTS AND CALIBRATIONS — REV. #2 (04/09/14) — PAGE 9
� Trailer should be adjusted to a level position at all times when towing.
�Raise and lock trailer wheel stand in up position when towing.
�Place chock blocks underneath wheel to prevent rolling while parked.
�Place support blocks underneath the trailer’s bumper to prevent tipping while parked.
�Use the trailer’s swivel jack to adjust the trailer height to a level position while parked.
ENVIRONMENTAL SAFETY
NOTICE
�Dispose of hazardous waste properly. Examples of potentially hazardous waste are used motor oil, fuel and fuel fi lters.
�DO NOT use food or plastic containers to dispose of hazardous waste.
�DO NOT pour waste, oil or fuel directly onto the ground, down a drain or into any water source.
SAFETY INFORMATION
PAGE 10 — HTXD6i/STXD6i TROWEL • SETUP, ADJUSTMENTS AND CALIBRATIONS — REV. #2 (04/09/14)
TOOLS NEEDED
The specialized tools listed in Table 1 are required to maintain and service the HTXD6i and STXD6i ride-on trowels. Fleet technicians and servicing dealers must have these tools for efficient unit setup and component calibration.
Table 1. Setup, Calibration, and Diagnostic ToolsTOOL DESCRIPTION PART NO. QTY
Tool Kit Includes all tools listed below. 32061 1
CAN Gateway Cable
Required to interface to the trowel MCU. Required for foot pedal calibration, pitch sync calibration, stroke cylinder calibration, engine fault code reading, diagnostics, ETC.
22882 1
Gauge Tool (3.25”)Used in calibrating one of the two blade pitch set points as part of the synchronization process.
32044 2
Gauge Tool (2.25”)Used in calibrating one of the two blade pitch set points as part of the synchronization process.
32000 2
Set Up Jumper
Used to place the engine at full speed for component calibration and to simultaneously disable both the stroke follower and cold start mode.
32007 1
Pedal WrenchUsed to help set the foot pedal sensor. It is also used for setting the Zero Pitch Cylinder Stops by using the thickness of the wrench.
32020 1
HTXD6i/STXD6i TROWEL • SETUP, ADJUSTMENTS AND CALIBRATIONS — REV. #2 (04/09/14) — PAGE 11
MACHINE INFORMATION
MODEL
1. Enter appropriate model:
�HTXD6i — for 6-blade HTX
�STXD6i — for 6-blade STX
SERIAL NUMBER
2. Machine Serial Number — as shown on serial tag.
3. Engine Serial Number — located on top of engine (E/N) (Figure 1) or stamped on side of block (Figure 2).
Figure 1. Engine Serial Number Location 1
Figure 2. Engine Serial Number Location 2
NOTICE
The following machine information should be recorded on Machine Information and Maintenance Log for unit service tracking and for filing any warranty claims.
4. Pump Serial Number — located on sticker on pump (Figure 3). The lower number is the pump serial number.
Figure 3. Pump Serial Number Location
5. Motor Serial Number — located on sticker on top of hydraulic motors (Figure 4).The lower number is the motor serial number.
Figure 4. Motor Serial Number Location
NOTICE
If lot number is listed instead of the serial number, record lot number.
PAGE 12 — HTXD6i/STXD6i TROWEL • SETUP, ADJUSTMENTS AND CALIBRATIONS — REV. #2 (04/09/14)
GENERAL PROCEDURES
SETUP JUMPER INSTALLATION
1. Remove Cap (P\N: 22812) on P24 of main harness (under foot platform).
2. Install Setup Jumper (P/N: 32007 on P24).
NOTICE
These general procedures will be referenced in other sections throughout the manual.
NOTICE
Machine must be secured prior to installation. Installing setup jumper will:
• Disable Cold Start
• Increase Engine RPM to Full operating RPM
• Disable Stroke Follower
REMOVE SETUP JUMPER(If installed).
1. Remove Setup Jumper (P\N: 32007) from P24 of main harness.
2. Re-install Cap (P\N: 22812) on P24 of main harness.
Table 2. Disable and Re-enable Options
DISABLE
(If Setup Jumper is not installed)
Cold Start
1. Open service tool.2. Click “machine setup” button on main page.3. Click “Cold Start” button under Setup Menu.4. Click check box next to Disabled.5. Press Download Button.
Stroke Follower
1. Open service tool.2. Click “machine setup” button on main page.3. Click “Stroke Cont.” button under Setup Menu.4. Click button “Disable Stroke Follower”.
RE-ENABLE
(If disabled via service tool)
Cold Start
1. Open service tool.2. Click “machine setup” button on main page.3. Click “Cold Start” button under Setup Menu.
4. Uncheck box next to Disable.
5. Press Download Button.
Stroke Follower
1. Open service tool.2. Click “machine setup” button on main page.3. Click “Stroke Cont.” button under Setup Menu.4. Click button “Enable Stroke Follower”.
HTXD6i/STXD6i TROWEL • SETUP, ADJUSTMENTS AND CALIBRATIONS — REV. #2 (04/09/14) — PAGE 13
INITIAL CHECK AND ADJUSTMENTS
PRELIMINARY CHARGE PRESSURE ADJUSTMENT
1. Loosen 1-1/16" jam nut on charge relief valve (Item A, Figure 5).
2. Use a 1/2" socket to adjust the small hex nut within the larger hex jam nut (Item B, Figure 5).
3. Rotate small hex nut (Item B, Figure 5) clockwise until bottomed out. DO NOT overtighten.
Figure 5. Preliminary Charge Pressure Adjustment
NOTICE
Skipping this step during initial set-up may cause machine to inadvertently move during further steps, due to insufficient charge pressure.
A
B
OIL AND COOLANT CHECK
Hydraulic Oil Check
1. Make sure the machine is cold.
2. Remove the starwheel cap (Figure 6) and visually check oil level.
3. Make sure that it is filled to the red line as shown in Figure 6.
4. Put back and tighten starwheel cap after checking or filling.
Figure 6. Oil Level Check
NOTICE
The sight glass is only used to check the fluid condition (dirt or air bubbles) and not to check the oil level.
FLUID CONDITION
SIGHT GLASS
OIL LEVEL
(FULL)
REMOVE STARWHEEL
CAP TO CHECK OIL LEVEL
PAGE 14 — HTXD6i/STXD6i TROWEL • SETUP, ADJUSTMENTS AND CALIBRATIONS — REV. #2 (04/09/14)
Engine Oil
1. Ensure engine is level.
2. Remove the oil filler cap (top or side). See Figure 7.
Figure 7. Adding Engine Oil
3. Add the required amount of engine oil at the top or side engine oil filler port.
4. Wait 3 minutes then proceed with next step.
5. Remove dipstick and wipe clean with cloth.
6. Fully reinsert dipstick.
7. Remove the dipstick. The oil level should be between the upper and lower) lines on the dipstick.
8. Add more oil if necessary and repeat steps 4 to 7.
9. Reinstall the oil cap and hand tighten. Over-tightening may damage the cap.
ENGINE OIL
FILLER CAP
ENGINE OIL
FILLER CAP
DIPSTICK
F
LADD OIL
FULL
Engine Coolant
1. Verify that the radiator drain cock is closed.
2. Remove radiator cap.
3. Pour engine coolant slowly into the radiator until it is even with the lip of the engine coolant filler port (Figure 8).
Figure 8. Adding Engine Coolant
4. Reinstall radiator cap.
5. Remove the cap on the reservoir tank.
6. Fill to the low mark (Cold Mark) with engine coolant (Figure 9).
Figure 9. Reservoir Tank
INITIAL CHECK AND ADJUSTMENTS
HTXD6i/STXD6i TROWEL • SETUP, ADJUSTMENTS AND CALIBRATIONS — REV. #2 (04/09/14) — PAGE 15
SERVICE TOOL SETUP AND CONNECTION
WHITEMAN SERVICE TOOL (WST) INSTALLATION
1. Call or e-mail Multiquip Technical Support or Field Service to obtain the application specific Whiteman Service Tool (WST) file.
2. Also obtain software license key through Multiquip Technical Support or Field Service.
3. The WST file will be sent to you as an attachment to an e-mail.
4. Open the e-mail sent by Multiquip and click on the attachment. On the drop-down menu, select "Save Target As" (Figure 10).
Figure 10. Saving WST Application File
5. Do not change the file name. Save the file to your desktop.
6. Locate and verify that the WST application file (22708P) was saved to your desktop.
NOTICE
Make sure that the Sauer Danfoss Plus Software is already installed before proceeding with the Whiteman Service Tool (WST) installation.
Whiteman Application File
17
• Right click the
attachment file and on the drop down menu select “ Save Target As “.
• Save this file to the desktop location.
• Do not change the file name.
WST – Whiteman Service Tool
Look for ICON on your computers desktop.
7. Double-click on the 22708P Icon on your desktop. One of the screens shown in Figure 11 will appear. Click "Cancel".
Figure 11. WST Navigation Bar (Not Populated)
8. Click "Cancel" again when the new screen (Figure 12) comes up.
Figure 12. WST Navigation Bar (Populated)
Click “Cancel”Navigation Baris not populated
Click “Cancel”Navigation Baris not populatedWhiteman Service Tool Application
Connecting Laptop to Trowel
20
• After canceling from previous screen, this new screen will open but the navigation bar is populated.
Click cancel
PAGE 16 — HTXD6i/STXD6i TROWEL • SETUP, ADJUSTMENTS AND CALIBRATIONS — REV. #2 (04/09/14)
9. The new screen will have both navigation and tool bars active (Figure 13.)
Figure 13. WST Tool Bar
10. Click on "Tools". On the drop-down menu, click on "License Manager" (Figure 14).
Figure 14. WST License Manager
11. Input the license key obtained from Multiquip (Figure 15) and click "OK".
Figure 15. Entering License Key
Whiteman Service Tool Application Connecting Laptop to Trowel
21
• After canceling from previous screen, this new screen will open with full Navigation and tool bars active..
Whiteman Service Tool Application Connecting Laptop to Trowel
22
• License Key Install • Click on License
Manager
• Input you license key and click OK.
Whiteman Service Tool Application Connecting Laptop to Trowel
22
• License Key Install • Click on License
Manager
• Input you license key and click OK.
SERVICE TOOL SETUP AND CONNECTION
HTXD6i/STXD6i TROWEL • SETUP, ADJUSTMENTS AND CALIBRATIONS — REV. #2 (04/09/14) — PAGE 17
LAPTOP CONFIGURATION
CONNECTION PROCEDURE
1. Plug the CAN Gateway cable to the trowel at the service port (Figure 16). Do not connect laptop at this time.
Figure 16. CAN Gateway Cable to Service Port
2. On the trowel, turn the ignition key to the ON position (Figure 17). This will turn on the MCU. It is not necessary to crank or turn on the engine.
Figure 17. Ignition Key ON
3. Connect the USB connector of the CAN Gateway cable to the USB port (Figure 18).
Figure 18. Connecting the Laptop
NOTICE
Make sure that the Sauer Danfoss Plus Software and Whiteman Service Tool (WST) are installed before proceeding with the connection procedure.
Whiteman Service Tool Application Connecting Laptop to Trowel
24
• Turn the Key to the ON position, Cranking or turning on the engine is not required.
CRANK
ON ACC OFF
4. When the CAN Gateway cable is connected to the laptop for the first time, it is necessary to install the CAN driver software. The installation screen will appear (Figure 19). Click "Next" to install the software automatically (default).
Figure 19. CAN Driver Installation
5. Click "Finish" on the next screen (Figure 20) to complete installation.
Figure 20. CAN Driver Installation Complete
6. On the Service Tool software on your laptop, the main screen should show Firmware info loaded from trowel MCU and the Machine Status box shows lamps lit (Figure 21).
Figure 21. Service Tool Main Screen
Connecting Laptop to Trowel
26
• First time connected.
• CAN Driver Software install.
WST – Whiteman Service Tool
Connecting Laptop to Trowel
26
• First time connected.
• CAN Driver Software install.
WST – Whiteman Service Tool
Connecting Laptop to Trowel
27
• Main Screen
• Firmware info is loaded from MCU
• Machine Status box shows LAMPS lit.
WST – Whiteman Service Tool
PAGE 18 — HTXD6i/STXD6i TROWEL • SETUP, ADJUSTMENTS AND CALIBRATIONS — REV. #2 (04/09/14)
MACHINE SETUP AND CALIBRATION
CALIBRATE FOOT PEDAL
1. Turn key to ON position but DO NOT start machine.
2. Click “CALIBRATION” button on machine setup page.
3. Click “CALIBRATION” button in "PEDAL SENSOR" frame (Figure 22).
Figure 22. Calibration Button
NOTICE
Prior to calibration of the foot pedal sensor, ensure the mechanical movement is not restricted. It should smoothly depress to the hard stop and smoothly return to full released position.
Sensor Adjustment
1. Read % sensor voltage. If 15% to 25%, skip to calibration section. Otherwise, continue with next step to adjust sensor (Figure 23).
Figure 23. % Sensor Voltage
2. Using 7/16 wrench, rotate foot pedal shaft (Item B, Figure 24) , while holding foot pedal lever (Item A, Figure 24) in upright position, until % sensor voltage is 15% to 25%.
3. Verify that jamb nuts are tight (Item C, Figure 24)
Figure 24. Sensor Adjustment
NOTICE
If sensor is preset, during assembly, with P\N: 32020, WRENCH, PEDAL SETUP, this step may be skipped.
NOTICE
This may require loosening of jamb nuts.
A
AC
B
HTXD6i/STXD6i TROWEL • SETUP, ADJUSTMENTS AND CALIBRATIONS — REV. #2 (04/09/14) — PAGE 19
MACHINE SETUP AND CALIBRATION
Calibration
1. Set sensor zero position default:
a. Ensure that foot pedal is fully released.
b. Read % SENSOR VOLTAGE.
c. Round % Sensor Voltage value to nearest percent and enter in CALB POINT 1 DEFAULT.
d. Press "Download" button to update value in MCU.
2. Set sensor full position default:
a. Fully depress pedal.
b. Read % Sensor Voltage (Figure 25).
c. Round value to nearest percent and enter in CALB POINT 2 DEFAULT.
d. Press "Download button" to update value in MCU.
Figure 25. Start Pedal Sensor Calibration
3. Press “START” button to begin calibration and follow prompts.
4. Once calibrated, move pedal thru range, ensuring calibrated signal moves from 0 to 100%.
5. Record Calibration Values on Machine Information and Maintenance Log.
SECONDARY HYDRAULIC FILL PROCEDURES
1. Elevate machine so blades are no longer contacting floor.
2. Start the unit and run the engine.
3. Check level while machine is cold.
4. Remove the starwheel cap (Figure 6) and visually check oil level.
5. Fill as needed so oil is at the top line of the reservoir (red line in Figure 26) and that the oil level cannot be seen in the fluid condition sight glass.
Figure 26. Checking Oil Level
6. Put back and tighten starwheel cap after filling.
7. Turn off machine and lower.
NOTICE
Once the oil heats up, any oil expansion will go up the overflow hose and into the fluid expansion tank.
Removing the oil fill cap, once the fluid is at operating temperature, will cause fluid loss as the expansion will cause oil to spill out.
FLUID CONDITION
SIGHT GLASS
OIL LEVEL
(FULL)
REMOVE STARWHEEL
CAP TO CHECK OIL LEVEL
PAGE 20 — HTXD6i/STXD6i TROWEL • SETUP, ADJUSTMENTS AND CALIBRATIONS — REV. #2 (04/09/14)
MACHINE PRESSURE ADJUSTMENT
Charge Pressure Adjustment
1. Disable cold start.
2. With machine off, install gauge capable of reading 300 psi to Charge Or Pitch pressure test port (Figure 27).
Figure 27. Pressure Test Ports Location
3. Restart machine.
4. Increase engine rpm to full operating RPM (an operator must be present on the seat to reach full engine speed).
NOTICE
All pressures to be adjusted with machine at full engine RPM.
To adjust pressures, cold start must be disabled through the Whiteman Service Tool (WST).
NOTICE
DO NOT depress the foot pedal with the 300-600 PSI gauge installed. Immediate damage to the gauge will occur.
Cold start must be disabled. Failure to do so will cause immediate damage to the gauge.
MACHINE SETUP AND CALIBRATION
5. Loosen 1-1/16" jam nut on charge relief valve (Item A, Figure 28).
Figure 28. Charge Pressure Adjustment
6. Using a 1/2" socket, adjust the small hex nut within the larger hex jam nut (Item B, Figure 28).
7. Adjust to proper charge pressure: 300 ±25 psi.
8. Record pressure on Machine Information and Maintenance Log.
9. Retighten jam nut.
10. Return engine rpm to idle.
11. Turn off machine and remove gauge.
Pitch Pressure Check
1. Disable cold start.
2. Install a 3000 PSI range pressure gauge to Charge or Pitch pressure test port (Figure 27).
3. Start machine and increase engine rpm to full operating RPM.
4. Activate left pitch switch.
5. Flatten blades (bottom out the pitch cylinders).
6. Continue to hold down pitch switch and measure pressure. If pressure is within range (1850 PSI to 2000 PSI), no adjustment is required. If pressure in not within range, proceed to Pitch Pressure Adjustment section.
7. If no adjustment is required, record pressure on Machine Information and Maintenance Log.
A
B
HTXD6i/STXD6i TROWEL • SETUP, ADJUSTMENTS AND CALIBRATIONS — REV. #2 (04/09/14) — PAGE 21
MACHINE SETUP AND CALIBRATION
8. Return engine rpm to idle.
9. Turn off machine and remove gauge.
Pitch Pressure Adjustment
1. Disable cold start.
1. Increase engine rpm to full operating RPM.
2. Loosen 3/4" jam nut on pitch relief valve (Figure 29).
Figure 29. Pitch Pressure Adjustment
3. Using a 1/4" allen wrench, adjust the small hex nut within the larger hex jam nut.
4. Tighten 3/4" jam nut.
5. Check the pressure as described earlier (see Pitch Pressure Check section).
6. If pressure requires further adjustment, repeat steps 2 through 4 until pressure check reads 1850 ± 50 PSI.
7. Record pressure on Machine Information and Maintenance Log.
8. Return machine engine rpm to idle.
9. Turn off machine and remove gauge.
Steering Pressure Adjustment
1. Disable cold start.
2. Install a 300 or 600 PSI gauge on steering pressure port (Figure 27).
3. Start machine.
4. Increase engine rpm to full operating RPM.
5. Loosen 3/4" jam nut on steering valve (Figure 30).
Figure 30. Steering Pressure Adjustment
6. Using a 1/4" allen wrench, adjust the small hex nut within the larger hex jam nut.
7. Adjust to proper steering pressure:
• HTXD6i: 245 psi ± 10 psi (Cold Oil) 235 psi ± 10 psi (Hot Oil)
• STXD6i: 300 psi ± 10 psi (Cold Oil) 290 psi ± 10 psi (Hot Oil)
NOTICE
DO NOT depress the foot pedal with the 300-600 PSI gauge installed. Immediate damage to the gauge will occur.
3/4-INCH
JAM NUT
ADJUSTMENT
SCREW
STEERING
VALVE
1/4-INCH
HEX NUT
PAGE 22 — HTXD6i/STXD6i TROWEL • SETUP, ADJUSTMENTS AND CALIBRATIONS — REV. #2 (04/09/14)
8. Retighten jam nut.
9. Return engine to idle.
10. Turn off machine and remove gauge.
11. Record Pressure on Machine Information and Maintenance Log.
12. Re-enable cold start.
TROWEL SPEED ADJUSTMENT\SETUP
Adjust Zero Stroke Position
1. Start machine.
2. Ensure trowel is running at idle with no stroke. On a cold trowel, the unit will go into cold start mode and not be at idle. To place the trowel at idle speed, disable cold start with the WST.
3. Elevate machine so blades are no longer contacting floor. Make sure to follow proper lifting procedures. Refer to Lifting Safety Information section.
4. Ensure blades are not rotating. If rotating, continue to next step and adjust per instructions. Otherwise, set trowel on ground and verify jamb nut (Item D, Figure 31) is tight then continue to next section (Left Side Trowel Speed Adjustment).
Figure 31. Zero Stroke Position Adjustment
CAUTION
Machine movement will occur during this step. Ensure machine is secure or operator is present in seat. All guards should be in place. Keep fingers, hands, hair, and clothing away from all moving parts to prevent injury.
E
D
C
A B
MACHINE SETUP AND CALIBRATION
5. Lower trowel and shut off.
6. Loosen Jamb nut (Item D, Figure 31).
7. Remove retaining screw (Item C, Figure 31). The spacer (Item A, Figure 31) will also come off.
8. Turn rod end (Item B, Figure 31) in, shortening overall length of cylinder assembly.
9. Reinstall retaining screw (Item C, Figure 31) and spacer (Item A, Figure 31). Apply blue loctite to make sure screw will not come off.
10. Tighten jamb nut (Item D, Figure 31).
11. Restart machine and repeat steps 2 thru 8 as necessary, until blades no longer spin.
Left Side Trowel Speed Adjustment
1. Install setup jumper or disable stroke follower.
2. Start machine, on bare floor and pitch until blade tips are about ½” off the ground.
3. Fully depress pedal and measure Left Side Trowel Speed.
4. Adjust speed limit screw and tighten jamb nut (Figure 32).
Figure 32. Left Side Trowel Speed Adjustment
NOTICE
Stroke sensor must be recalibrated after trowel speed adjustment for proper machine operation.
HTXD6i/STXD6i TROWEL • SETUP, ADJUSTMENTS AND CALIBRATIONS — REV. #2 (04/09/14) — PAGE 23
MACHINE SETUP AND CALIBRATION
5. Re-measure speed, repeating steps 2 and 3 until Left Side Trowel Speed is correct:
a. HTXD6i — 157 to 160 RPM (942 to 960 Pulses per minute)
b. STXD6i— 127 to 130 RPM (762 to 780 Pulses per minute)
6. Record L.H. speed on Machine Information and Maintenance Log in machine setup area.
Right Side Trowel Speed Adjustment
1. Verify setup jumper is installed or stroke follower is disabled.
2. Fully depress pedal, measure Left Side and Right Side Trowel Speed.
3. Adjust trowel arm connecting rod on the pump actuating lever and tighten jamb nuts (Figure 33).
Figure 33. Adjusting Right Side Trowel Speed
4. Re-measure speed and repeat steps 2 and 3 until Left Side and Right side are within 1 RPM of each other.
5. Record R.H. speed on Machine Information and Maintenance Log in Machine Setup section.
6. Remove setup jumper or re-enable stroke follower.
NOTICE
Stroke sensor must be recalibrated after trowel speed adjustment for proper machine operation.
The trowel speeds should be adjusted on a dry concrete floor with the blades pitched slightly (tips about 1/2” off ground).
Calibrate Stroke Sensor
1. Turn machine off for at least 10 seconds.
2. Restart machine.
3. Install Setup Jumper or disable Stroke Follower.
4. Click “Calibration” button on machine setup page.
5. Click “Calibration” button in STROKE SENSOR section (Figure 34).
Figure 34. Calibrate Stroke Sensor
CAUTION
Machine movement will occur during this step. Ensure machine is secure or operator is present in seat. All guards should be in place. Keep fingers, hands, hair, and clothing away from all moving parts to prevent injury.
PAGE 24 — HTXD6i/STXD6i TROWEL • SETUP, ADJUSTMENTS AND CALIBRATIONS — REV. #2 (04/09/14)
6. Set Sensor zero position default:
a. Ensure foot pedal is fully released.
b. Read % Sensor Voltage (Figure 35).
Figure 35. Start Stroke Sensor Calibration
c. Round value to nearest percent and enter in CALB POINT 1 DEFAULT.
d. Press "Download" button to update value in MCU.
7. Set Sensor full position default:
a. Have an operator fully depress pedal and hold at full blade speed.
b. Read % Sensor Voltage.
c. Round value to nearest percent and enter in CALB POINT 2 DEFAULT.
d. Press "Download" button to update value in MCU.
8. The operator must be on the unit to drive and stroke the cylinder. Have a second person press the “START” button and indicate to the operator what the prompts are on the screen. The unit will be run from no stroke to fully stroked during this calibration.
9. After calibration sequence is completed, click "EXIT".
10. Once calibrated, the second person must move pedal thru range and the operator ensures stroke follows and calibrated signal moves from 0 to 100%.
MACHINE SETUP AND CALIBRATION
PITCH SETUP
Prior to pitch setup, check and make sure that the following are in excellent condition to ensure eventual proper blade pitch synchronization and proper blade flatness.
�Blade condition - check for no excessive wear, new blades preferred
� Trowel arm bushings
�Pitch bolt adjustment for flatness
�Pitch bolt head for excessive wear
�Wear plate
� Thrust plate bearing and bushing - must lubricate
�Yoke for excessive wear
Flatten Blades
1. Adjust blade pitch adjustment bolts as necessary to ensure machine operates smoothly (Figure 36).
Figure 36. Blade Pitch Adjustment
CAUTION
Machine movement will occur during this step. Ensure machine is secure or operator is present in seat. All guards should be in place. Keep fingers, hands, hair, and clothing away from all moving parts to prevent injury.
BLADE PITCH
ADJUSTMENT BOLT
TROWEL
LEVER
TROWEL
ARM
TROWEL
BLADE
SPIDER
PLATE
HTXD6i/STXD6i TROWEL • SETUP, ADJUSTMENTS AND CALIBRATIONS — REV. #2 (04/09/14) — PAGE 25
MACHINE SETUP AND CALIBRATION
Measure Blade Leading Edge Height
1. Fully pitch machine by pressing and holding Twin pitch up button until pitch cylinders fully extended.
2. Choose a blade on both LH and RH Rotor. Using Gauge P/N 32044, measure height of raised leading edge ensuring it is 2.00” ±.060” (Figure 37). If the blade slides under the first step but not the next, it is within limits.
Figure 37. Measuring Leading Edge Height
Leading Edge Height Adjustment
1. If leading edge height is within limits (2.000” ± .060”) for left and right side, then no adjustment is needed. Otherwise, proceed to next step for adjustment.
2. Flatten blades (bottom out the pitch cylinders).
3. Remove clevis pin (Item E, Figure 38). Loosen jamb nuts (Item C, Figure 38) and adjust clevis (Item D, Figure 38) to cylinder (Item A, Figure 38) position, to raise or lower pitch as required.
Figure 38. Blade Leading Edge Height Adjustment
4. Tighten jamb nuts(Item C, Figure 38) and reinstall clevis pin (Item E, Figure 38).
5. Re-measure as per instructions in “Measure Blade Leading Edge Height” section.
6. Repeat steps 2 thru 5 until Left and Right leading edge height are within limits.
A
ED
C
PAGE 26 — HTXD6i/STXD6i TROWEL • SETUP, ADJUSTMENTS AND CALIBRATIONS — REV. #2 (04/09/14)
Set Zero Pitch Cylinder Stops
1. Flatten blades (bottom out the pitch cylinders).
2. Turn machine off.
3. Remove clevis pin (Item E, Figure 39) from pitch cylinder allowing yoke (Item B, Figure 39) to rest on thrust collar.
Figure 39. Zero Pitch Adjustment
4. Loosen jam nut (Item C, Figure 39) with ¾” wrench.
5. Set distance between head of stop (Item D, Figure 39) and yoke (Item B, Figure 39) to .075” (14 gauge steel, Gauge #32020).
6. Loctite and tighten jam nut (Item C, Figure 39).
7. Reinstall clevis pin (Item E, Figure 39) between pitch cylinder and yoke.
Pitch Sensor Calibration
EB
C
D
CAUTION
Machine movement will occur during this step. All guards should be in place. Keep fingers, hands, hair, and clothing away from all moving parts to prevent injury.
NOTICE
Pitch mode switch must be in the manual position.
MACHINE SETUP AND CALIBRATION
1. Turn machine off for at least 10 seconds and then restart machine.
2. Click “Calibration” button on machine setup page.
3. Click “Calibration” button in Pitch Sensors section (Figure 40).
Figure 40. Pitch Sensor Calibration
4. Press “zero” button (Figure 42) to begin calibration.
5. Set Calibration Point 1.
a. Press Hard Ext. button to fully extend pitch cylinders.
HTXD6i/STXD6i TROWEL • SETUP, ADJUSTMENTS AND CALIBRATIONS — REV. #2 (04/09/14) — PAGE 27
b. Install 3.25” Gauge (P/N 32044) over both Left and Right Cylinders as shown in Figure 41.
Figure 41. Gauge Installation
c. Press Hard Ret. button to retract cylinder onto gauge.
d. Verify gauge is tight between cylinder body and clevis.
e. Press “Set T1” button (Figure 42).
Figure 42. Start Pitch Sensor Calibration
f. Record values on Machine Information and Maintenance Log in Machine Setup section.
3.25” GAUGE
MACHINE SETUP AND CALIBRATION
g. Press Hard Ext. Button to fully extend pitch cylinders.
h. Remove gauge.
6. Set Calibration Point 2.
a. Install 2.25” Gauge P/N 32000 over both Left and Right Cylinders as shown in Figure 41.
b. Press Hard Ret. Button to retract cylinder onto gauge.
c. Verify gauge is tight between cylinder body and clevis.
d. Press “Set T2” Button.
e. Record values on Machine Information and Maintenance Log in Machine Setup section.
f. Press Hard Ext. Button to fully extend pitch cylinders.
g. Remove gauge.
7. Set Calibration Point 3.
a. Ensure Hard Ext. is active and pitch cylinders are fully extended.
b. Press “Set L1” button.
c. Record values on Machine Information and Maintenance Log in Machine Setup section.
8. Set Calibration Point 4.
a. Press Hard Ret. button to fully retract cylinders, ensure yoke is against zero pitch stop.
b. Press Soft Ext. button, and wait until yoke is pressing against thrust collar.
c. Press “Set L2” button.
d. Record values on Machine Information and Maintenance Log in Machine Setup section.
9. Once calibrated, move pitch thru range ensuring calibrated signal moves from 0 to 100%.
10. Turn machine off for 10 seconds.
PAGE 28 — HTXD6i/STXD6i TROWEL • SETUP, ADJUSTMENTS AND CALIBRATIONS — REV. #2 (04/09/14)
INSPECTION
FLUID LEVELS
Record the following fluid levels on Machine Information and Maintenance Log in Inspection section. Refer to Fluid Fill and Check section for procedure.
�Engine Oil �Engine Coolant �Hydraulic Oil
MECHANICAL
1. Grease Points — Ensure that the following Grease Points are greased, wiped down and capped:
• Thrust Collar• Fingers
2. Stabilizer Rings
a. Verify at least 1 thread is visible below lower bolt on all heim joints (Figure 43).
Figure 43. Visible Thread
b. Verify heim joint is centered, and not rotated, when bolted on Figure 44).
Figure 44. Heim Joint Orientation
3. Hydraulics
• Spot check paint marks on fittings.• Ensure that there are no leaks.
4. Retardant Spray System
• Fill with water and perform operational check.• Verify no leaks.
5. Electrical (Cooling Fan)
• Verify fan cycles on when key is turned on (will remain on for 10s).
• Verify air flow direction is outward.
6. Lights
• Verify operation of all 6 machine lights.
7. Switches
• Verify proper operation of all switches.
8. Indicators
• Verify illumination when key is turned on (will remain on for 10s)
• Red Stop Lamp• Amber Warning Lamp• Pitch Mode Light• Cruise Control Light• Coolant Temp• Aux 1• Aux 2
9. Aesthetics
• Paint Quality- No bare spots- No scratches
• Decals- Readable-Not torn or scratched
HTXD6i/STXD6i TROWEL • SETUP, ADJUSTMENTS AND CALIBRATIONS — REV. #2 (04/09/14) — PAGE 29
STATIC BLADE PITCH DRIFT TEST
1. Switch smart pitch switch to off position.
2. Bring machine up to temperature. This will be indicated by “Cold Start” (aux 1) lamp turning off.
3. Choose one blade from each spider and mark with small X to identify.
4. Using the Twin pitch button, cycle the blades from flat to full pitch 8 times leaving the blades in the full pitch position on the eighth cycle.
5. Turn the engine off, and record time and tip height on Machine Information and Maintenance Log.
6. Leave for a 3-hour test period then re-measure tip height. Record height and time on Machine Information and Maintenance Log.
7. Compare the two measurements. Drift exceeding 3/16” in three hours is unacceptable.
INSPECTION
PAGE 30 — HTXD6i/STXD6i TROWEL • SETUP, ADJUSTMENTS AND CALIBRATIONS — REV. #2 (04/09/14)
FUSE INFORMATION
Table 3. Fuses
Fuse Number Amps Designator Functions Fused
1 20T13 MCU Power
T21 Service Port Connector
2 20 T3 Oil Cooler
3 5T5 Light Switch
T15 Pitch Switches
4 20 T6 Left Lights
5 7.5 T23 Sprayers
6 20 T7 Right Lights
Table 4. Ground
Location Designator Functions Grounded
Top LeftT12 MCU
T14 Pitch Switch, Throttle, Cruise, LED's, Cluster gauge
Middle LeftT20 Service Port Connector
T24 Spray Pumps
Bottom Left
T25 Rear Lights
T26 Pitch Switch, Throttle, Cruise, LED's, Cluster gauge
T28 Engine Harness
Bottom RightT1 Pitch Valves
T2 Control Relay
Middle RightT4 Cooler Fan
T27 Front Right Lights
Top RightT31 PRM (Power Relay Module)
T32 Hour Meter
Refer to Figure 45 for location on fuse panel.
Figure 45. Fuse and Ground Location
20
5
7.5
20
20
20
TL TRMRBR
MLGROUND
FUSES
FUSE PANEL
FUSES
GROUND
BL
HTXD6i/STXD6i TROWEL • SETUP, ADJUSTMENTS AND CALIBRATIONS — REV. #2 (04/09/14) — PAGE 31
NOTES
SETUP, ADJUSTMENTS AND CALIBRATIONS
Your Local Dealer is:
HERE’S HOW TO GET HELPPLEASE HAVE THE MODEL AND SERIAL
NUMBER ON-HAND WHEN CALLING
United StateSMultiquip Corporate Office MQ Parts Department
18910 Wilmington Ave.Carson, CA 90746 Contact: [email protected]
Tel. (800) 421-1244Fax (310) 537-3927
800-427-1244310-537-3700
Fax: 800-672-7877Fax: 310-637-3284
Service Department Warranty Department
800-421-1244310-537-3700
Fax: 310-537-4259 800-421-1244310-537-3700
Fax: 310-943-2249
Technical Assistance
800-478-1244 Fax: 310-943-2238
Canada United Kingdom
Multiquip Multiquip (UK) Limited Head Office
4110 Industriel Boul.Laval, Quebec, Canada H7L 6V3Contact: [email protected]
Tel: (450) 625-2244 Tel: (877) 963-4411Fax: (450) 625-8664
Unit 2, Northpoint Industrial Estate, Globe Lane,Dukinfield, Cheshire SK16 4UJContact: [email protected]
Tel: 0161 339 2223 Fax: 0161 339 3226
© COPYRIGHT 2014, MULTIQUIP INC.
Multiquip Inc , the MQ logo and the Whiteman logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other trademarks are the property of their respective owners and used with permission.
This manual MUST accompany the equipment at all times. This manual is considered a permanent part of the equipment and should remain with the unit if resold.
The information and specifi cations included in this publication were in effect at the time of approval for printing. Illustrations, descriptions, references and technical data contained in this manual are for guidance only and may not be considered as binding. Multiquip Inc. reserves the right to discontinue or change specifi cations, design or the information published in this publication at any time without notice and without incurring any obligations.
PN: 32399