Http Www.dgserve HPSV Fitt

7/31/2019 Http Www.dgserve HPSV Fitt

1/18

15-NOV-1Download Date:Page 1 of 18

Sub: Rate Contract for supply of HPSV Fittings & Accessories

Validity: From 01-JAN-11 To 31-DEC-11 .

Ref:(1) This Office Tender Enquiry No. HPSV Fitt./ES-7/RC-A1030000/1211/37Opened on 09-DEC-10.

(2) Your Quotation No. RE/RC:HPSV FITT(T)/2010/880 And Dated

09-DEC-10.

Dear Sir,

You are hereby informed that your above refered tender read with subsequent letters mentioned above for the Stores

specified in the Schedules annexed has been accepted. This rate contract will be governed by the terms and conditions

brought in the Form no. DGS&D 1001 available from dgs&d sales counter on payment of Rs. 50/- .The Rate Contract

and the schedules annexed here to shall be the sole repository of this Rate Contract/Transaction.

SCHEDULES ANNEXED

1.Schedule "A" Description of stores,prices,duties/taxes.

2.Schedule "B" special conditions of contract / Other information.

3.Schedule "C" Information to DDOs about parallel rate contracts.

4.Annexure - Technical Specification

Yours Faithfully,

( )

Assistant Director(S)/Section Officer/Dy.Director

For and on behalf of the purchaser named in the Form DGS&D 1001.

Government of India

Directorate General of Supplies & Disposals

Jeevan Tara Building, 5 Sansad Marg

New Delhi-110001

Tel Number 23360610/23360537

Rate Contract no. HPSV Fitt./ES-7/RC-A1030000/1211/37/05807/1432

Dated 03-JAN-11

Rate Contract

To,

RAJ ELECTRICALS

214, FUNCTIONAL INDUSTRIAL ESTATE, PATPARGANJ,

DELHI,


2/18


COPY TO:

1.The Chief Controller of Accounts,Department of commerce,New Delhi/

COA Mumbai/COA Kolkata,COA Chennai.

(Through authentication cell) This issues with the approval of competent authority.

2.Deputy Director General of Supplies & Disposals,Chennai -10 copies each

3.Deputy Director General of Supplies & Disposals,Kolkata -10 copies each4.Deputy Director General of Supplies & Disposals,Mumbai -10 copies each

5.Deputy Director General (QA),Kolkata -10 copies each

6.Deputy Director General (QA),Chennai -10 copies each

7.Deputy Director General (QA),Mumbai -10 copies each

8.Deputy Director General (QA),DGS&D -10 copies each

9.Inspection Authority ADG(QA) DGS&D New Delhi - 110001.

10.Quality assurance Officer Director (QA) Delhi Directorate/ Mumbai,Chennai/Kolkata.

11.Concurrent Audit

12.MIS Cell

13.Ledger clerk

14.O.L.Section15.All Direct Demanding Officers as per mailing list maintained by DGS&D.

( )

Assistant Director (S) / Section Officer / Deputy Director

FOR DIRECTOR GENERAL OF SUPPLIES & DISPOSALS


3/18


1.Rate Contract No.:-HPSV Fitt./ES-7/RC-A1030000/1211/37/05807/1432

Dated 03-JAN-11 For the Supply of HPSV Fittings & Accessories

2.Advance Rate Contract No.:-

Dated

3.(a) Name and Full Address of the Firm :-

---------------------------------------------------------------------------------------------------------------------------------------------

Item Model Store Description Unit RateNo. No. (in

Rs.)

---------------------------------------------------------------------------------------------------------------------------------------------

Type: for 70 Watt Lamps



26.45

26.45

26.45

Spare Ignitors

Spare Ignitors

Spare Ignitors

SCHEDULE - A

NOS.

NOS.

NOS.

13

14

15

DELIGHT

DELIGHT

DELIGHT

Rs.

TWENTY-

SIX AND

PAISE

FORTY-

FIVE

ONLY

Rs.

TWENTY-

SIX AND

PAISE

FORTY-

FIVE

ONLY

RAJ ELECTRICALS

214, FUNCTIONAL INDUSTRIAL ESTATE,

PATPARGANJ,

DELHI,

DELHI - 110092

Tel. No. - 22143204/5/6

Fax - 22160513

Email - -

(b) Name and Full Address of Manufacturer :-

RAJ ELECTRICALS


PATPARGANJ, DELHI

110092

(c) Brand: DELITE

4.Validity of Rate Contract: 01-JAN-11 To 31-DEC-11

5.Description of Item, Specification,Unit, Rate


4/18



Type: for 70 Watt Tubular Lamps




26.45

1469.79

2420

2648.25

2888.72

Spare Ignitors

Street Light Fittings with

IP-66 Protection


IP-66 Protection


IP-66 Protection


IP-66 Protection

NOS.

NOS.

NOS.

NOS.

NOS.

16

17

18

19

20

DELIGHT

DELIGHT

DELIGHT

DELIGHT

DELIGHT

Rs.

TWENTY-

SIX AND

PAISE

FORTY-

FIVE

ONLY

Rs.TWENTY-

SIX AND

PAISE

FORTY-

FIVE

ONLY

Rs. ONE

THOUSAN

D FOUR

HUNDREDSIXTY-

NINE AND

PAISE

SEVENTY-

NINE

ONLY

Rs. TWO

THOUSAN

D FOUR

HUNDREDTWENTY

ONLY

Rs. TWO

THOUSAN

D SIX

HUNDRED

FORTY-

EIGHT

AND

PAISETWENTY-

FIVE

ONLY

Rs. TWO

THOUSAN

D EIGHT

HUNDRED

EIGHTY-


5/18


6/18


( )

Asstt. Director (S) / Section Officer / Dy. Director

For and behalf of the purchaser named in the Form DGS&D 1001.

All the R/C particulars including prices in respect of individual R/Cs are available on DGS&D website which can be

accessed by all.The DGS&D website is http://dgsnd.gov.in

23-Packing & Specification :

Supply order(s) in any other form placed on or after 01-10-2008 shall not be valid and shall not be acted upon by the

contractor or any other concerned agencies.

DDO shall download the supply order and send an ink signed copy to the concerned paying authority specified in the

rate contract through Registered / speed post immediately after on-line placement of Supply Order(s).

see annexure


7/18


SCHEDULE - B

RC Specification:1 70 Watt HPSV Class IP-66 Street Light Fittings

1.01 Over all Dimension of fitting (LXWXH)

(Tolerance -5%)

550mmX250mmX155mm

1.02 Bare weight of fitting in Kg (Min) 3.520 Kg

1.03 Type of gasket used and its specification Neoprene1.04 Total weight of fitting with fixture but without lamp 5.3 Kg.

1.05 Whether detail dimensional drawing depicting all

parts? and colour photograph available with tenderer Yes

1.06 Indicate the pattern of punch marking on flange of

ballast for unique identification of product.

R1

2 150 Watt HPSV Class IP-66 Street Light Fittings


(Tolerance -5%)

630mmX280mmX160mm

2.02 Bare weight of fitting in Kg (Min) 4.630 Kg.

2.03 Type of gasket used and its specification Neoprene

2.04 Total weight of fitting with fixture but without lamp 7.32 Kg


parts? and colour photograph available with tenderer

Yes



R1



(Tolerance -5%)

700mmX310mmX180mm3.02 Bare weight of fitting in Kg (Min) 5.340 Kg.


3.04 Total weight of fitting with fixture but without lamp 9.25 Kg.



Yes



R1


4.01 Over all Dimension of fitting (LXWXH)(Tolerance -5%)

700mmX315mmX190mm

4.02 Bare weight of fitting in Kg (Min) 5.350 Kg.


4.04 Total weight of fitting with fixture but without lamp 10.95 Kg.



Yes




8/18


R1


9/18


1

2

3

4

5

6

7

8

HPSV Fitt./ES-7/RC-

A1030000/1211/37/03242/1430

HPSV Fitt./ES-7/RC-

A1030000/1211/37/04512/1431

HPSV Fitt./ES-7/RC-A1030000/1211/37/05455/1442

HPSV Fitt./ES-7/RC-

A1030000/1211/37/05454/1444

HPSV Fitt./ES-7/RC-

A1030000/1211/37/NA071/1438

HPSV Fitt./ES-7/RC-

A1030000/1211/37/04739/1433

HPSV Fitt./ES-7/RC-

A1030000/1211/37/05761/1427

HPSV Fitt./ES-7/RC-

A1030000/1211/37/04681/1439

03-JAN-11

03-JAN-11

03-JAN-11

03-JAN-11

03-JAN-11

03-JAN-11

03-JAN-11

03-JAN-11

INDUSTRIAL KALINGA

LITON LIGHTING INDUSTRY

TWINKLE LUNINAIRES PVT LTD

TWINKLE INDUSTRIES

LORD KRISHNA ELECTRONIC INDUSTRIES

ELECTROCINE INDUSTRIES

COMMANDER ELECTRICALS

SATYA ENGINEERING WORKS PVT.

LIMITED

6/3&4,Katori Mill,Rajender NagarIndl.Area,G.T.Road

K.No. 22/6/1, Peepal Wali Gali, Gali No.9, Samaypur

Badli,

C-59, Preet Vihar, Vikas Marg, Delhi

C-59, Preet Vihar, Vikas Marg,

23-24 KRISHAN KUNJ, LAXMI NAGAR,

56/18, Site-IV, Indl Area, Sahibabad, Ghaziabad

D-14, 15, 114 & 115, Shreenath Industrial Estate,S. No. 197, B/H Voltas,

Dadra Check Post

A-111, Mangol Puri Indl. Area,

Phase-II,

Sahibabad

Delhi

Delhi

Delhi,

DELHI

Ghaziabad

Dadra

UTTAR PRADESH

DELHI

DELHI

DELHI

DELHI

UTTAR PRADESH

DADRA NAGAR HAVELI

201007

110042

110092

110092

110092

201010

396230

Sr.No. NAME & FULL ADDRESS OF FIRM R/C NO & DATE

SCHEDULE - C

List of Parallel Rate Contract For HPSV Fittings & Accessories


10/18


8

9

10

11

12

13

14

15

16

17

HPSV Fitt./ES-7/RC-

A1030000/1211/37/04681/1439

HPSV Fitt./ES-7/RC-

A1030000/1211/37/04793/1440

HPSV Fitt./ES-7/RC-

A1030000/1211/37/05459/1436

HPSV Fitt./ES-7/RC-

A1030000/1211/37/04297/1446

HPSV Fitt./ES-7/RC-

A1030000/1211/37/05047/1441

HPSV Fitt./ES-7/RC-

A1030000/1211/37/04432/1443

HPSV Fitt./ES-7/RC-

A1030000/1211/37/05807/1432

HPSV Fitt./ES-7/RC-

A1030000/1211/37/05601/1445

HPSV Fitt./ES-7/RC-

A1030000/1211/37/05204/1437

HPSV Fitt./ES-7/RC-

A1030000/1211/37/05758/1428

03-JAN-11

03-JAN-11

03-JAN-11

03-JAN-11

03-JAN-11

03-JAN-11

03-JAN-11

03-JAN-11

03-JAN-11

03-JAN-11

FLORIDA ELECTRICAL INDUSTRIES LTD.

JAIN INDUSTRIAL LIGHTINGS CORP.

ARUN ELECTRICALS

SUNEET APROTECH (P) LTD.,

ELTON ELECTRICALS PRIVATE LIMITED

RAJ ELECTRICALS

ATLAS INDUSTRIES

MAMTA PRODUCTS

LUXOLITE INDUSTRIES

B-147, Maya Puri Industrial Area, Phase-1

B-70/22, DSIDC Industrial Complex, Lawrence

Road,

1/5, Khandsa Road, Gurgaon-122001

2094/1, Gali No. 17, Prem Nagar,

1759, Modern Industrial Estate, Bahadurgarh,


PATPARGANJ,

71, S.S.I. Laghu Udyog Nagar, G.T. Karnal Road,

D-26, DSIDC Shed, Jhilmil Colony, Shahdara

A-2/25, Site-IV, Sahibabad Indl. Area, Distt.

Ghaziabad, U.P.

New Delhi

New Delhi

Delhi-110035

Gurgaon

New Delhi

Bahadurgarh

DELHI,

Delhi,

Delhi,

DELHI

DELHI

DELHI

HARYANA

DELHI

HARYANA

DELHI

DELHI

DELHI

110034

110064

110035

122001

110008

124507

110092

110033

110095


11/18


17

18

19

20

21

22

23

HPSV Fitt./ES-7/RC-

A1030000/1211/37/05758/1428

HPSV Fitt./ES-7/RC-

A1030000/1211/37/04782/1429

HPSV Fitt./ES-7/RC-

A1030000/1211/37/04842/1434

HPSV Fitt./ES-7/RC-

A1030000/1211/37/05460/1447

HPSV Fitt./ES-7/RC-

A1030000/1211/37/05461/1435

HPSV Fitt./ES-7/RC-

A1030000/1211/37/05680/1448

HPSV Fitt./ES-7/RC-

A1030000/1211/37/05796/1450

03-JAN-11

03-JAN-11

03-JAN-11

03-JAN-11

03-JAN-11

03-JAN-11

03-JAN-11

SINGHANIYA LITE & LUMINARIUES (P)

LTD.

KUKREJA ENGINEERS

MODERN LIGHTING SYSTEMS

KOHLI & COMPANY

ULTRA LIGHTING LTD.

TANEJA SALES CORPORATION

12/4, Ist Floor, Subhash Nagar

H-1201, D.S.I.D.C. Narela Industrial Area, Narela

Unit No.64, Block B-70, Dr.

Lohia Industrial Area,

Lawrence Road,

T-5, Okhla Indl. Area, Phase-II,

A-83, G.T. Karnal Road, Industrial Area, Azadpur,

A-83, G.T. Karnal Road, Industrial Area, Azadpur,

GHAZIABAD

New Delhi

Delhi

Delhi

New Delhi

Delhi,

Delhi,

UTTAR PRADESH

DELHI

DELHI

DELHI

DELHI

DELHI

DELHI

201010

110027

110040

110032

110020

110033

110033

NOTE:

(1) Before placing supply order, DDOs are advised to check with DGS&D or on the website whether any further RCs

have been awarded or amendments to Rate Contract have been issued.

(2) All the R/C particulars including prices in respect of individual R/C's are available on DGS&D website,which can be

accessed by all. The access code of DGS&D website is http://dgsnd.gov.in.


12/18


1. FITTINGS:

The fittings where specified shall be ISI marked to IS: 10322 (Part 5/Sec

3)-1987(Reaffirmed 2005) (Incorporating Amendment Nos. 1, 2, 3 & 4)

,IS:10322(Part5/Secl)-1985(Reaffirmed 2005)(Incorporating Amendment Nos. 1,& 2),IS

13383 (Part 2) : 1992( Reaffirmed 2000 ) (Incorporating Amendment No. 1) (for

photometric) as applicable and with the following additional requirements. Street

Light Fittings shall have photometric efficiency of 65%. Connecting wire from

control gear terminal block to lamp holder shall be of 1.1 KV grade, copper

conductor XLPE insulated.

2. BALLAST:-

Ballast shall generally conform to IS : 6616-1982( Reaffirmed 2006) with the

following variations:-

a)At rated voltage power delivered shall not be less than 92.5% and

not more than 107.5% of the power delivered by the reference ballast.

b)Between 92% and 106% rated voltage, the short circuit current shall be within

limits given in IS : 9974 (Part I)-1981(Reaffirmed 2002) (Incorporating Amendment

Nos. 1, 2, 3 & 4)under the heading ballast design information.

c)Abnormal operation (type test)is to be carried out in association with

ignitor

and as per ignitor specification and for each ratings.( Firm shall declare the

model

and manufacturer of ignitor for which their ballast is suitable)

d)High voltage test of 5 KV for one minute as a type test and 5 KV for 5

seconds as an acceptance test.

NOTE: Firm shall have to use their own make ballst for manufacturing of HPSV

fittings

3.IGNITOR:

I. Performance requirements between 92% & 106% of rated voltage.

(a)Pulse height,

(i) 1.8 KV to 2.3 KV-70W HPSV fitting

(ii) 2.8 KV to 4.5 KV-150W & above HPSV fittings.

(b)Direction & postion not material for the time being .

(c)Rise time 2 micro. secs. ( Maximum)

(d)Duration 0.9 to 8 micro. sec.

(e)Pulse repetition rate: 1 per cycle ref IS: 9974.

(f)Subsequent pulse height less than 70%.

II. Ignitor shall not pulsate after the lamp has been fully ignited i.e.current

though it shall be steady.III. Ignitors wrongly connected shall have not deliterious(adverse)effect on the

luminaire.

I.TYPE TESTING:.

A. FOR FITTINGS:- Additional requirements of type tests.

a) Temp. rise and voltage increase as per Clause IS : 9974 (Part I)-1981

(Reaffirmed 2002) (Incorporating Amendment Nos. 1, 2, 3 & 4).IS:9974 pt-II

should also be referred as applicable.

b) High voltage test of 5 KV for 1 Min with all terminals shorted and

ANNEXURE


13/18


capacitor

removed between terminal wire and earthing.

c) High Voltage test of 5 KV for1 Min. between two terminals of lamp and lamp

cap

(on lamp holders).

B. FOR BALLAST.

As per IS : 6616-1982( Reaffirmed 2006 ) and specification for ballast with

following additional requirements.

a) Abnormal operation(Type Test)is to be carried out in association with

ignitor and as per ignitors specification and for each rating. Firm shall declare

the model and manufacturer of ignitor for which their ballast is suitable.

b) High Voltage test of 5 KV for one Min. as a type test.

C. FOR IGNITORS.

i) Protection against accidental contact. The tests shall be conducted with

ballasts of makes offered by the firm in the luminaires/as spares.

ii) Moisture resistance, insulation resistance and electric strength (5KV for 1

Min.)The test will be conducted in accordance of IS : 6616 - 1982( Reaffirmed 2006

)

iii) Fault condition.

When starting device is operated under fault condition like shorting of

its terminal of lamp terminals, there shall be no emission of flame etc.& no

accessible

part will become live.

iv) HEATING TEST;

Heat test under normal conditions of operation with lamp at rated voltage

&

in abnormal condition without lamp at 110% voltage the components shall not

exceed

the permissible limits of operating temp. After these test and cooling down, the

ignitor shall operate normally.

v) Performance test for pulse characteristics.

Pulse characteristic measured with an appropriate osciloscope with ballast

& length of wire as provided by the manufacturer in the fitting upto the lamp

terminals.

vi) Creepage distance.

Test will be conducted in accordance of IS : 6616-1982( Reaffirmed 2001 ).

vii) Endurance

In this test two ignitors are connected as in normal use associated with an

appropriate ballast.The test voltage shall correspond to 1.06 x the rated supply

voltage of the ballast. The ignitors are operated in conformity with their

marking at the maximum allowable temp. in the fittings and without lamp.

In doing so the connections of one of ignitors are loaded by the maximum

allowable load capacitance say 1000 or unless otherwise specified while the

connections of the other ignitors are left unloaded.After 30 days of continuous

test they shall meet the requirement and ignite the lamp.

ACCEPTANCE TEST:

A FOR FITTING:-

a. High voltage test of 2.5KV for one minute with all terminals shorted and

capacitors removed between terminals wire and earthing. High Voltage of 2.5 KV

for one minute between two terminals of lamp cap ( on lamp holders).


14/18


b. Acceptance test as per governing specification.

B. FOR BALLAST.

In addition to tests referred in the specification the following tests are to be

conducted.

a. Performance test with lamp, ignitor and ballast.

b. Watt loss and cold resistance on random samples drawn as per sampling plan for

acceptance tests specified in in IS:6616 .however Sample size would be double of

that specified in IS:6616. The value of watt loss at nominal rated current

circulating directly and measured by a watt meter of 0.2 pf at an ambient

Temperature of 27 degree C shall conform to the following:

i) Watt loss shall not exceed the figures as under:-

For 70 Watts Lamp ballast - 15 Watts maximum




ii) Resistance tolerance + 5% to -10% (Tenderers to declare the nominal cold

resistance value of winding in their offer).

iii) For energy efficient ballasts samples size for acceptance tests shall be

double the number of samples as indicated in IS:6616 and tests for limitation of

ballast heating will be conducted an acceptance test on each lot, each ballast

will be marked with watt loss and S.No. of the ballast.

C) FOR IGNITORS.

i) To be carried out on 4 samples out of every lot of 1000 Nos. and all sample

shall pass.

ii) Measurement of pulse height, duration, rise time, pulse rate etc. with the

ballast offered.

iii)High voltage test at 5 KV for 5 seconds.

D) Condensor shall conform to IS : 1569 /1976 (Reaffirmed 2001) (Incorporating

Amendment No. 1) and shall be suitable to give a power factor of 0.85 (minimum)

E) Lamp holders shall conform to IS: 10276 / 1982(Part I & II) (Reaffirmed 2003).

1. Suppliers shall furnish complete and satisfactory type test certificate as per

T/E specification for each item to the concerned DQA at the time of registration &

inspection.TTC shall be from any Government laboratory.

2. Lamps shall not be the part of supply.

QA PROCEDURE:

The following procedure are incorporated to augment the inspection process:

1. The firms shall furnish detailed drawing along with bill of material of each

rating/ variety of HPSV fittings for which they have been awarded DGS&D rate

contract. These drawings should also indicate average weight of the fittings (with

manufacturing tolerance) and should be in consonance with drawings/ sketches

vetted by Lab at the time of type testing .

2. Firms shall declare the source of aluminum die cast body, toughened glass,

aluminum reflector and neoprene rubber gasket and make/ model/ rating of bought

out electrical components being used in manufacturing/assembly of HPSV fittings.

They should also maintain record and proof of periodical testing of critical


15/18


components. .

3. Firms shall also declare the weight of the finished copper wound ballast,

weight of the stamping and its type/ grade, size of winding wire, weight of copper

winding wire and cold resistance of winding wire at 20 degree C (all with

tolerances) for each rating of HPSV ballast. Value of resistance may be converted

as per engineering practice at any required temprature.

4. For re-traceability purpose unique identification mark of the firm and serial

number/ lot number shall also be punched on the flange of ballast. In case a firm

prefers to punch the lot number, the same should not be repeated for the lot

offered for next inspection/ future.

5. Firms shall also keep QA office informed as to when die cast bodies are

received by them and ready for painting so that QA officer may be able to verify

the process on periodical basis and ensure the quality of casting as per

specification.

6. Dimension of fitting shall be as per indicative value given in specification

of TP. .Fresh TTC is not required for mere change in dimension / size if

fittings being tendered/offered are having greater size in comparison to

sizes indicated in sketch of type tested products of different ratings which has

been authenticated by lab. How ever if sizes of type tested fittings are more

than required value , firms have to offer products accordingly and they are not

allowed to reduce sizes.

7. During inspection the QA officers shall also verify the offered stores for

their conformance with the declaration made by the firm.

The overall dimensions (LxWxH) & weight of the fittings, weight and cold

resistance of ballast winding at 20 0C, punched unique identification mark of the

firm & lot number and serial numbers of ballasts shall be recorded in the I/notes

for the guidance of the consignees with the explicit remark that the stores may be

checked for these parameters and deviations if any should be reported for

appropriate corrective and preventive action .

8. Samples of items tested out of the lot offered for first inspection are to be

retained by firm with detailed identification ( R/C no, rating, date of

inspection, TTC no etc) for comparison during subsequent inspection. Retention

period of sample should not be less than 24 months since dispatch of last

consignment to user against this R/C.

Spare Ignitors

Street Light Fittings with IP-66 Protection

Specification :

Spare Ignitors for luminaires against schedule -66 i.e. IP-66

class (make & type) to be specified and to be supported with test reports. Also

refer to GTR

Specification :

Street Light Luminaires, IP-66 Class ISI marked to IS : 10322


16/18


17/18


of

IS 10322 ( Part I ) : 1982( Reaffirmed 2005 ). Fittings shall have photometric

efficiency of 65%.

vii.) Dimension of fittings i.e. Length x Width x Height for respective rating

should be as under with maximum permissible minus tollerace on dimension of 5%:

70 Watt: 550x250x150

150 Watt: 630x280x160

250 Watt: 690x310x180

400 Watt: 700x315x190

All dimension are in mm and without any restriction on upper limit on dimension.

It may be noted that above dimensions are given for homogenity however once

dimension declared by firm as per their manufacturing drawing allowable

manufacturing tollerance in negative side shall not be more than 5mm which may

arise due to shrinkage etc.

Drawing/Proforma/Annexure Attached [Click on the following to View/Print ]

Inspection Report Performa
https://www.dgserver.dgsnd.gov.in/IR_HPSVFITTING.pdfhttps://www.dgserver.dgsnd.gov.in/IR_HPSVFITTING.pdf


18/18

LIST OF ALL AMENDMENTS

For RC No. HPSV Fitt./ES-7/RC-A1030000/1211/37/05807/1432

Sr No. Amendment No. Amendment

Date

Effective

From

HPSV Fitt./ES-7/RC-A1030000/1211/37/05807/1432/343611 04-JAN-11 03-JAN-11

Amendment In

Amendment in E

Duty,Annexure &

Clauses
http://www.dgserver.dgsnd.gov.in/formseal/server/custompdfsigner.jsp?TID=HPSV%20Fitt./ES-7/RC-A1030000/1211/37/05807/1432/34361/04-JAN-11&FORMNAME=RCAMEND&URL=/reports/rwservlet?KEY1&report=rcamendAPPROVpdf.rdf&destype=cache&desformat=pdf&PRCNO=HPSV%20Fitt./ES-7/RC-A1030000/1211/37/05807/1432&LETNO=nil&PFILE=04A10300001211&DKDATE=04-01-2011&LETDATE=http://www.dgserver.dgsnd.gov.in/formseal/server/custompdfsigner.jsp?TID=HPSV%20Fitt./ES-7/RC-A1030000/1211/37/05807/1432/34361/04-JAN-11&FORMNAME=RCAMEND&URL=/reports/rwservlet?KEY1&report=rcamendAPPROVpdf.rdf&destype=cache&desformat=pdf&PRCNO=HPSV%20Fitt./ES-7/RC-A1030000/1211/37/05807/1432&LETNO=nil&PFILE=04A10300001211&DKDATE=04-01-2011&LETDATE=

Http Www.dgserve HPSV Fitt

Documents

Transcript of Http Www.dgserve HPSV Fitt