Hspa 72 User Per Cell Activation

7/16/2019 Hspa 72 User Per Cell Activation

http://slidepdf.com/reader/full/hspa-72-user-per-cell-activation 1/7

RAN1686: HSPA 72 Users per Cell

Activating HSPA 72 Users per Cell

Purpose

Follow the procedure below to activate the RAN1686: HSPA 72 Users per Cell feature.

For more information on the feature, see the RAN1686: HSPA 72 Users per Cell featuredescription in WCDMA RAN, rel. RU20, feature descriptions.

Before you start

Restart of the RNC and the WBTS is not required after activation of this feature.

This feature belongs to application software and is under license key management. Makesure you have a valid license (a file including the feature information) installed. To check if the RNC license is activated, use the W7I command. For more information on using the

command, see W7 - Licence and Feature Handling.

Before a licensed feature can be activated, the license must be transferred to and installedin the RNC. For information on transferring the license to the RNC, see License managementoperations in RNC in WCDMA RAN license management.

You can install the license using NetAct or a local MML interface. If you install the licenseusing NetAct, the feature covered by the license is automatically set to the ON state. Forinformation on license management in NetAct, see Managing Licenses, License Manager Help, Licence Manager Technical Reference Guide, and Licence Manager

problems inTroubleshooting System Management Problems in Nokia Siemens NetworksNetAct documentation.

If you use the MML interface, you must also set the feature state (ON/CONFIG/OFF). In newinstallations, the default state is OFF. For the specific instructions on the license installationin the RNC, see W7L INSTALL OR UPDATE LICENCE in W7 - Licence and Feature Handling.

For more information on license management, see License management principles,and License management in WCDMA RAN.

To set the feature state (ON/CONFIG/OFF), use the following command:

W7M:FEA=<feature code>:<feature state>;

The feature code for this feature is1478.

RAN1686: HSPA 72 Users per Cell feature needs the following features to be activatedbefore it can be enabled:

• HSDPA

• HSUPA

• RAN312: HSDPA Dynamic Resource Allocation



The value of the MaxNumberEDCHLCGparameter depends on the BTS HW. The value

of MaxNbrOfHSSCCHCodescan be 4 only when the flexi release2 HW/EUBB is used.

Steps

1. Open the OMS Element Manager.

2. Go to the Tree View .

2 Go to the Tree View .

Follow this path:

“Configuration Management Network Topology Tree View”

Expand the topology tree of the RNC.

3. Configure the RNFC object.

3Configure the RNFC object.

1. Select Edit parameters from the RNFC object.

2. Under the Packet Scheduler tab, enable HSDPA dynamic resource allocationwith HSDPADynamicResourceAllocation(HSDPA Dynamic Resource Allocation)

configuration parameter.



Figure 57: Setting the HSDPADynamicResourceAllocationparameter

4. Lock the cell.



5. Configure the WCEL object.

5Configure the WCEL object.

1. Select Edit parameters from the WCEL object.

2. Under the Admission Control tab, enable HSDPA with HSDPAEnabled (HSDPA enabled) RNP

parameter, and under the Packet Scheduler tab HSUPA withHSUPAEnabled (HSUPA enabled)

RNP parameter.



Figure 59: Setting the HSDPAEnabledparameter

Figure 60: Setting the HSUPAEnabledparameter



3. Enable HSPA 72 users per cell feature with HSPA72UsersPerCell(HSPA 72 Users per Cell)

management parameter.

Figure 61: Setting the HSPA72UsersPerCellparameter



6. Unlock the cell.

Expected outcome

Feature HSPA 72 Users per Cell has been activated.

Id: 0900d80580812f07 ©2011 Nokia Siemens Networks

DN0988674

Hspa 72 User Per Cell Activation

Documents

Transcript of Hspa 72 User Per Cell Activation