H&S Manual West Sussex
-
Upload
annie-hawkins -
Category
Documents
-
view
216 -
download
0
Transcript of H&S Manual West Sussex
-
7/30/2019 H&S Manual West Sussex
1/68
|}~
Health and Safety Manual forDesign & Technology, Art &Design, Ceramics, Textiles andFood Technology at KS3 andhigher
West Sussex County Council
Issue March 2009
Please report any errors to the Health and Safety Team, 01243 752025
Crown copyright material is reproduced under Class Licence Number
CO1W0000189 with the permission of the Controller of HMSO and the Queen's
Printer for Scotland.
Material produced by the LA may be copied for use within West Sussex LAeducational establishments. For material that is neither Crown copyright nor
produced by the LA, please obtain the permission of the publisher before making
copies of the material.
Main changes are shown as dark blue text.
1
-
7/30/2019 H&S Manual West Sussex
2/68
|}~
Contents
..................................................................................................................... 7Introduction.......................................................... 9Part A. General guidance for all curriculum areas
.................................................................................................. 9Accidents and incidents.................................................................................... 9Investigating and monitoring accidents
..................................................................................................................... 10Adhesives................................................................................................................. 10Hot-melt glue guns
................................................................................................. 10Cyanoacrylates (superglues).................................................................................................................... 10Wall-paper paste
............................................................................... 10Buying safe goods and equipment............................................................................................................ 11Cleaning rooms
........................................................................ 12Educational visits and off-site activities................................................................................................................... 12Outdoor activities
.................................................................................................. 12Wildlife and Countryside Act..................................................................... 12Activities offered by people receiving your visit
...................................................................................................................... 13Electricity................................................................................................................. 13Electricity isolators
........................................................................................... 13Room electricity emergency stop........................................ 14The fixed installation (the building wiring up to the power socket)
......................................................................................................................... 14Socket outlets.............................................................................................. 14Checking and using equipment
.............................................................................................................. 15Approved equipment..................................................................................................... 15Maintenance of equipment
................................................................................................ 15Home-made mains apparatus............................................................................................................................ 15Low voltage
.......................................................................................................... 15Rechargeable batteries..................................................................................................................... 16Fire safety
............................................................................................................ 16Fumes and dust............................................................................................................. 17Cleaning dusty areas
.................................................................................................... 17Hazardous materials............................................................................. 18Risk assessments and control measures.
............................................................................................................ 18Prohibited substances.............................................................................................................. 18ICT equipment
................................................................................................ 19Safe use of laptop computers
2
-
7/30/2019 H&S Manual West Sussex
3/68
|}~
...................................................................................................... 20Visual display units (VDU).......................................................................................................... 20Interactive whiteboards
................................................................21 Ladders, steps and other access equipment.........................................................................21 Lifting operations and lifting equipment
.................................................................................................................22 Lone working.................................................................................23 Management of health and safety
.................................................................................................................. 23Risk assessments..................................................................................................................... 24Keeping records
...................................................................................................... 25Health and safety policies...................................................................................................................... 26Responsibilities
.............................................................................................................................27Class sizes................................................................................................................... 27Using workrooms................................................................................................................. 28Delivery of lessons.................................................................................................................. 28Cover supervisors
.................................................................................................................... 29Tutor/form rooms....................................................................29Maintenance of equipment and practical rooms
.........................................................................................29Safety signs, notices and displays..................................................................................................................... 29Making artefacts
............................................................................................................30 Manual handling.............................................................................................................................30 Noise
...........................................................................31 Pupils with special educational needs..........................................................................................................31 Pressure systems
......................................................................................................... 32Hired pressure systems........................................................................................................... 32Model stream engines.
.....................................................................32 Protective clothing and safety equipment..................................................................................................................................32Clothing
..................................................................................................... 32Eye protection and guardsEye-wash................................................................................................................................ 33
..................................................................................................................................33First-aid................................................................................................33 Services: water and gas
.......................................................................................................................... 33Gas supplies.................................................................................................................. 34Using gas burners
......................................................................................................................................34Water
.........................................................................................................................34 Storage............................................................................................................................34Flammables
..............................................................................................................................35Corrosives..................................................................................................................................35Shelving
3
-
7/30/2019 H&S Manual West Sussex
4/68
|}~
.................................................................. 35Tools: hand tools and portable power tools.............................................................................................................................. 35Hand tools
.............................................................................................................. 35Portable power tools............................................................................................................................... 36Glue guns
........................................................................................................................ 36Training........................................................................................................................... 36Waste
.................................................................................................................... 37Disposable items................................................................................................................. 37Combustible swarf
............................................................................................... 37Metal swarf, sharps and glass............................................................................................ 37Chemically hazardous materials................................................................................. 38Part B. Specific curriculum areas
.................................................................................................... 38Design &Technology............................................................................................................ 38Workshop supervision
............................................................................................... 38National standards for training................................................................................... 39D&T: Machinery and equipment
........................................................................................ 39Restrictions on machine operators................................................................................................. 40Specific portable power tools
.............................................................................................................. 40CAD/CAM machines.......................................................................................................................... 40Laser cutters
....................................................................................................................... 41Machine siting.................................................................................................................... 41Emergency stops
.......................................................................................................................... 42Start controls..................................................................................................................... 42Braking devices.
................................................................................................................ 42Planer/thicknessers................................................................................................................. 42Equipment stability
........................................................................................ 42D&T: High-temperature work.................................................................................................................................. 43Welding
..................................................................... 43Casting and other very high temperature work.............................................................................................................. 43Protective equipment
............................................................................................................................... 43Asbestos.............................................................................. 44D&T: Working with wood and metal
..................................................................................................................................... 44Metals....................................................................................... 44Oils, greases and cutting lubricants
...................................................................................................................................... 44Wood.................................................................................................................... 45Wood treatments
................................................................................................................ 45
Adhesives for wood........................................................................................... 45D&T: Working with plastics
4
-
7/30/2019 H&S Manual West Sussex
5/68
|}~
........................................................................................................................ 45Burning plastic..............................................................................................45Glass-reinforced plastic (GRP)
........................................................................................................... 45Expanded polystyrene.......................................................................................45 D&T: Working with electronics
................................................................................................................................46Soldering.......................................................................................................... 46Processing photo-resist
...................................................................................................................................46Etching........................................................................................................... 46Electronic components
...........................................................................................46Flux cleaners and other solvents...................................................................................46 D&T: Working on motor vehicles
......................................................................................................... 46Working on engines etc;................................................................................................................ 47Working under cars
........................................................................................................ 47Paint spraying (vehicles)..................................................................................................... 47Other hazardous materials
..........................................................................................................48 Food Technology.......................................................................................................................... 48Water quality
..................................................................................................... 48Avoiding burns and scalds.............................................................................................................................48Deep frying
.......................................................................................................................... 48Sugar-boiling....................................................................49
Thermometers and other measuring equipment
.....................................................................................................................................49Floors..........................................................................................49Cleaning materials, bleaches etc.
.................................................49Using sodium carbonate (washing soda) as a drain cleaner.....................................................49Food technology: cookers and domestic machinery
..................................................................................................................................49Cookers................................................................................................................ 50Microwave cookers
............................................................................................................. 50Restricted equipment.............................................................................................51 Food technology: hygiene
.................................................................................................... 51Microbiology, food tests etc................................................................................................................... 51Personal hygiene
...................................................................................................................................51StorageWaste bins.............................................................................................................................. 51
.................................................................................................................... 51Chopping boards.............................52Art & Design: working with solvents, paints and graphics materials
..................................................................................................................................53Solvents............................................................................................................ 53Spraying / air brushes
..................................................................53 Art & Design: working with stone and glass
5
-
7/30/2019 H&S Manual West Sussex
6/68
|}~
...................................................................................................................................... 53Glass............................................................................................................................. 54Enamelling
...................................................................................................................................... 54Stone........................................................................................... 54Art & Design: photography
.............................................................................................................................. 54Darkrooms.......................................................................................................................... 54Photo-resists
.............................................................................................................. 55Ultra-violet light (UV)......................................................................................... 55Cameras and optical instruments.
.................................................................... 56Ceramics: working with glazes and stains........................................................................................................................... 56Using glazes
.................................................................................................................... 56Preparing glazes............................................................................................................. 57Storage and labelling
Ceramics: kilns and machinery..................................................................................... 57..................................................................................................... 57Clay processing machines
................................................................................................................. 57Kilns and furnaces................................................................................................................................ 58Gas kilns
........................................................................................................................... 58Maintenance......................................................................................................................... 59Textiles
.................................................................................................................................. 59Flooring................................................................................................................... 59Sewing machines
............................................................................................................................ 59Fabric irons....................................................................................................................................... 59Batik
.................................................................................................................................... 59Dyeing................................................................................................................. 59Flameproof fabrics
......................................................................................... 60Appendix: Room Checklists............................................................................................................. 61Textiles Rooms
................................................................................................. 63Art & Ceramics Rooms...................................................................................................... 65Workshop Checklist
................................................................ 67Food Technology Rooms (food preparation)
6
-
7/30/2019 H&S Manual West Sussex
7/68
|}~
Introduction
This manual is for subject leaders and staff of Design & Technology, Art &
Design, and includes Graphics, Ceramics, Textiles and Food Technology. It sets
the standards required by the LA that schools must follow. The purpose of this
document is to ensure safe practice in technology at KS3 and higher. This
document must be made available to all teachers and technicians involved in
teaching these areas and they must use the information in planning practical
work. There are other essential documents to this one:
CLEAPSS CD-ROM for Design and Technology, 2003. Relevant to Design and
Technology, Art & Design, Ceramics, Textiles, and Food Technology
BS4163:2007. Health and Safety for Design and Technology in Schools and
Similar Establishments: British Standards. This is relevant to craft, electronics,
engineering, food, graphics, manufacturing, product design, systems and control,
textiles and ICT.
A Guide to Safe Practice in Art & Design . (www.nsead.org/hsg/index.aspx. This is
an updated version of the DfE A Guide to Safe Practice in Art and Design 1995.)
These documents, with this manual, form the basis of the LAs arrangements and
risk assessments for health and safety in Design &Technology, Art & Design,
Ceramics, Textiles, Food Technology, Graphics, etc. These documents havebeen issued to all secondary schools. If you have misplaced the first two, contact
the Health and Safety Team on 01243 752025. The last document has been
reproduced on the CD-ROM with permission from HMSO. Departments must
have copies of this information readily available for staff to use, and for inspection
by LA advisers, County Council Health and Safety Officers, OfSTED inspectors,
and the Health and Safety Executive.
There are two other guidance documents issued by the DCSF that are useful.
These are for Design and Technology areas, Building Bulletin 81 "Design and
Technology Accommodation in Secondary Schools: A Design Guide" (Revised
2004). (It is available for download from
www.archive2.official-documents.co.uk/document/deps/dfes/81/81.pdf), and for
Art and Design areas, Building Bulletin 89 Art Accommodation in Secondary
Schools 1998, available from The Stationery Office, ISBN 0112710298.
Please contact an appropriate member of Adults and Children - Learning or
Health and Safety Team if you wish to discuss any of the guidelines in this file, or
problems in implementing them. The School Standards and Framework Act and
the precursor, the Local Management of Schools, has given schools increased
delegated powers and duties in running schools, including health and safety
responsibilities to staff, children and visitors. The manual explains these health
7
http://www.nsead.org/hsg/index.aspxhttp://www.archive2.official-documents.co.uk/document/deps/dfes/81/81.pdfhttp://www.archive2.official-documents.co.uk/document/deps/dfes/81/81.pdfhttp://www.nsead.org/hsg/index.aspx -
7/30/2019 H&S Manual West Sussex
8/68
|}~
and safety responsibilities and the principles of successful health and safety
management.
This document is specifically for health and safety matters relating to the design
& technology curriculum areas, including art and design. For general health andsafety information relating to educational establishments, refer to the A-Z Health
and Safety section of WSGfL.
As a guide to what is reasonably practicable, the word should in this manual is
used to mean something that is recommended but not compulsory; these are
usually actions that are considered to be good working practices, but the
educational establishment is free to choose other actions if it has good reasons
for doing so. Conversely, the word must is used to mean something that is
compulsory, usually something statutory, and a failure to implement would be
breaching a law or LA policy, or breaching a duty of care.
8
-
7/30/2019 H&S Manual West Sussex
9/68
|}~
Part A. General guidance for all
curriculum areas
Accidents and incidents
In health and safety, an accident is an event that causes ill-health or injury, and
possibly damage to property or the environment. An incident is an event that
nearly causes ill-health, injury, damage to property or the environment (so it can
be called a near-miss). Never ignore a near-miss. It gives important information
on how to prevent a similar event happening again. If ignored, the consequencescould be much worse next time.
It is essential to report accidents and incidents, as it is an important way of
monitoring health and safety performance and identifying trends so that
resources can be targeted towards tackling specific areas of concern. The law
says that employers have to report serious accidents and incidents.
There are two levels of reporting and recording accidents and incidents: using
your local school accident and incident book, and reporting to West Sussex
County Council by filling in form HSW3. Full details are given for schools in the
Health and Safety A-Z on the WSGfL..
Investigating and monitoring accidents
Unless they are minor accidents where the cause is obvious, accidents and
incidents need to be investigated. The main reason for the investigation is to find
the cause of the accident to prevent it happening again. You should record any
findings and recommendations.
The investigator should be the person responsible for the area where the
accident happened, or the person in charge of the curriculum area if it happened
in a lesson. More serious accidents, where the injured person was taken tohospital, must be investigated by a senior manager in liaison with the Health and
Safety Team.
Accidents and incidents are usually caused by failures in control, and often have
several causes, both direct and indirect. Although the direct cause may be human
or technical failure, the indirect cause may be down to organisational failings or
oversights that managers are responsible for. When investigating an accident it is
important to look for both direct and indirect causes.
9
-
7/30/2019 H&S Manual West Sussex
10/68
|}~
Adhesives
Follow the guidance in the CLEAPSS CD-ROM for Design and Technology. Do
not use hazardous adhesives (for example, epoxy resins, cyanoacrylates andformaldehyde resins) when safer ones would do just as well. All glues must be
used in accordance with the manufacturers instructions. Be aware that some
solvent-based adhesives are used by glue-sniffers.
Hot-melt glue guns
Use the trigger-type only. Wear safety specs, and wear a protective glove on the
hand holding the work. A glue gun stand can be used to keep the gun clear of
glue drips. Before use, teach users the first-aid procedure should hot glue come
into contact with the skin; immerse the hand in clean cold water for at least five
minutes. Ensure that there is a source of cold water available, it should be atleast two metres away from the glue gun (preventing the risk of water being
spilled onto the glue gun).
Cyanoacrylates (superglues)
These may be used by teachers, technicians and pupils Y10 and above. Pupils
must be under direct supervision. Be very careful not to get this glue on anyones
skin. As with all dangerous materials, keep this glue locked away when not in
use..
Wall-paper pasteAvoid the use of paste which has fungicide in it - this is an irritant and can cause
an allergic skin reaction.
Buying safe goods and equipment
When you buy goods and equipment, you want to be sure that you get what you
pay for, and that they will not cause any harm to staff or children. The quality and
performance of equipment must be suitable for educational use
for example,items meant for DIY enthusiasts may not be suitable for children to use.
Buy from reputable suppliers, and avoid second-hand equipment unless you are
sure it is in good condition and suitable. If you need advice about buying
equipment, please contact the Supplies Advisory Service on 01243 777787 or
Adults and Children - Learning. Refer to BS 4163:2007 before to purchasing any
equipment to ensure its suitability, and to identify any training requirements.
The CE mark on equipment is not a guarantee of safety it says the
manufacturer is claiming the machinery complies with the law. Its up to you to
check the equipment is safe before it is used. There have been several cases inWest Sussex where schools bought CE-marked equipment from a high street
10
-
7/30/2019 H&S Manual West Sussex
11/68
|}~
DIY chain believing it to be a mark of quality, but the equipment had to be
condemned and scrapped because it was too dangerous to be used by children.
To help you choose safe and good value products:
research what it is you need contact other educational establishments for
recommendations
dont be misled by sales talk into buying unnecessary extras
ask for written confirmation that the goods or services will comply with relevant
safety standards
check for hidden costs or small print clauses
check to see if the goods or services are covered by a code of practice, or if the
company is a member of a trade association
if fitting or installation is involved, check to see that the person who will carry this
out is suitably qualified (eg an electrician or gas fitter)
if the equipment has replaceable parts, check that they are easily available at a
reasonable cost, and preferably that you can get them from a range of suppliers.
When ordering the goods, make sure your order identifies the exact goods,
specifications and standards required, cross-referencing to the suppliers
literature where necessary.
Cleaning rooms
Staff must keep the practical rooms clean and tidy. Walkways and work areas
should not be cluttered. Equipment and materials must be stored appropriately.
You need suitable equipment to clean dust. See the section on fumes and dust.
School staff must leave practical rooms, including preparation rooms, in a safe
state so the rooms can be cleaned safely. Cleaners must have induction training
before cleaning in hazardous areas such as machine workshops; the cleaning
staff must have been trained by their employer to use the appropriate cleaning
methods, particularly in ceramics areas and wood and metal machine workshops.
The employer has the principal responsibility for giving the training, but you
should check; dont assume it has been done.
You must explain to cleaners clearly if there area areas or equipment that should
not be cleaned. Do this in liaison with the premises manager or caretaker.
11
-
7/30/2019 H&S Manual West Sussex
12/68
|}~
Educational visits and off-site activit ies
Follow the advice and instruction in the Regulations and Notes of Guidance for
Educational Visits. Every school has been sent a copy of this. Each schoolshould also have an Educational Visits Co-ordinator. Off-site activities must be
organised within the guidelines of the LA (or school governors for Voluntary
Aided Schools) regarding parental permission, supervision, general safety,
transport, first aid and insurance.
A prior consultation or visit to the site by a teacher with appropriate experience is
essential.
The school must ensure that the site(s) being visited and the activities to be
carried out are suitable and safe for pupils (giving due consideration to the safety
measures and supervision that will be available). The same guidelines, whichapply to school technology generally, apply to off-site technological activities.
Give adequate information and warning to the pupils beforehand about
foreseeable hazards which would not normally encountered in school, such as
the dangers of eating fruits from wild plants, getting too close to machines which
are operational or wandering off without permission - particularly where there
may be dangers arising from industrial processes or, in the case of working
outside, dangerous waters or exposed heights.
Outdoor activities
Where relevant, make sure that the pupils, staff and helpers wear the appropriateclothing, headgear and footwear. Warn pupils not to handle dead animals which
they may come across outdoors. Be aware that old insect or animal nests may
have been treated with very harmful pesticides.
Wildlife and Countryside Act
You may not damage or uproot specially protected wild plants. You may take
other plants if they are on your own land or where you have permission from the
owner. It is permissible to pick flowers and fruits from unlisted plants growing
wild, but do not harvest them excessively. Do not remove or otherwise damage
nests or other animal habitats unless you are sure they are no longer used.
Activi ties offered by people receiv ing your visi t
If pupils take part in activities organised by agencies or other outside people, the
school must ensure that the activities are both suitable and safe. People may not
fully appreciate that activities which are suitable for adults can pose significant
risks to pupils. School organisers must satisfy themselves as far as reasonably
practicable that any work place being visited is following health and safety
regulations, including those for the control of substances hazardous to health.
12
-
7/30/2019 H&S Manual West Sussex
13/68
|}~
Electricity
Mains leads, plugs and sockets.
Plugs, leads and sockets must be checked regularly. Worn or damaged mainsflex must be replaced. All 230 volt mains plugs must be the standard 13 amp
square pin type with partly shrouded line and neutral pins, the older style plugs
with bare line and neutral pins should not be used. Staff may not wire up plugs
until they have received adequate training (this may be provided by a suitably
qualified and experienced member of the science department competent to do
this).
Electricity isolators
Each work area containing fixed electrical equipment (e.g. a resistant materials
room or a preparation area) must have a main lockable switch-disconnector thatswitches off all circuits to the fixed electrical equipment in the area. Ideally, it
should be located near the main entrance to the area and easily accessible to the
teacher. The main switch-disconnector must not isolate critical circuits specifically
installed to remove hazards.
All fixed equipment must be controlled by switch-disconnector (an isolating
switch) located either on the equipment or within two metres of the normal
operating position, and accessible to the operator. The cabling from the switch-
disconnector to the machine or equipment must be mechanically protected (eg.
armour-flex cable).BS4163:2007 recommends that electrical equipment for fixed machine tools
should be supplied by a fused switch-disconnector (conforming to BS EN 60947-
3, or a connection unit conforming to BS 1363-4, or a circuit breaker conforming
to BS EN 60898, or a residual current operated circuit-breaker (RCBO)
conforming to BS EN 61009-1). See BS4163:2007 subsection 5.2.6.
Room electrici ty emergency stop
Rooms with high power electrical machines should be fitted with adequate
emergency stops around the room that switch off all circuits supplied by the main
switch-disconnector. D&T machine shops must have them installed. See section
5 of BS 4163:2007. The stops must be tested regularly; if any malfunction, they
must be repaired by a qualified electrician without delay. Room emergency stops
are recommended in wood machine preparation rooms1; power to the
preparation room should not be affected if emergency stops in adjacent
workshops are activated.
1 There is conflicting advice regarding preparation rooms. BB81 recommends roomemergency stops in each work area containing fixed electrical equipment. However,BS4163:2007 states that emergency stops are not required in preparation rooms. Onbalance, WSCC recommends room emergency stops are fitted in preparation roomsunless there are overriding safety reasons for not doing so.
13
-
7/30/2019 H&S Manual West Sussex
14/68
|}~
The fixed installation (the building wiring up to the power socket)
No one is allowed to work on the fixed installation without agreement from
Property Services (maintained schools). If they have agreed the work, it can only
be done by a WSCC-approved contractor, or by a NICEIC contractor, or ECA or
J IB recognised electrician. The work must comply with the latest edition of the
IEE regulations for electrical installation (published by The Institution of
Engineering and Technology), and when it is finished, a completion certificate
must be sent to Property Services.
The mains wiring in workshops (single phase and three phase) must conform to
the requirements specified in section 3 of BS 4163:2007. The mains isolator and
emergency stops must be labelled clearly. No pupil or unauthorised person is
permitted to turn on the mains isolator.
Often you have to connect more than one device to a mains socket, particularlywith computer equipment - do not use socket adapters, use fused 13A rated
trailing distribution blocks. Extension leads may only be used as a temporary
method of powering portable equipment; they must not be used as permanent
fittings. Cable drum flex must be fully unwound before use. All flex must be
routed, guarded or protected so that it does not cause a danger of tripping
people.
Portable mains equipment used outdoors must be protected by an RCD (residual
current device).
Socket outlets
Socket outlets should be supplied via a non-time delayed residual current device
with a maximum tripping current of 30 mA. A maximum tripping current of 10 mA
should be used in areas where water might be present. See BS4163:007,
subsection 5.2.1 and 5.2.2. Where schools have no RCD fitted, this should be
planned through the school premises development plan.
Checking and using equipment
All users of portable mains equipment should carry out a simple and quick four-
point visual check before plugging a device into a socket and switching it on.
Are the plug and mains socket in good condition with no damage or
missing screws?
Is the flex in good condition - the flex outer sheath must go fully into the
plug and fully into the equipment?
Does the mains equipment appear in good order, free from dampness
and no obvious damage?
If the equipment has a switch, is it switched to off?
Remember, damp or wet mains conductors are dangerous. Do not attempt toremove damp plugs from sockets, isolate the supply first.
14
-
7/30/2019 H&S Manual West Sussex
15/68
|}~
Approved equipment
All mains electrical equipment used in schools must conform to relevant British
Standards specification or equivalent European standards. Do not use equipment
meant for domestic light use.
Maintenance of equipment
The electricity at work regulations requires that periodic tests are made to ensure
electrical equipment is in a safe condition. Portable electrical equipment should
be formally tested annually. The checks include examination for integrity of
connectors and flex, tests for earth bonding and for line-earth insulation. The
electricity regulations apply to the whole school, not just to the technology
department. Check with your school management for the arrangements for
electrical testing.
Home-made mains apparatus
Teachers/technicians are permitted to construct mains equipment for school use
provided that it is built to current British Standard specifications and is thoroughly
checked and tested by a competent and suitably qualified electrician before it is
used by others. The department must retain written evidence that the apparatus
passed electrical safety checks.
Low voltage
Pupils are not permitted to use power supplies with more than 33 volts on open
terminals; for younger pupils (under Y10) it is preferable to keep the supply below25 volts. Higher voltages are permitted if they are current limited to 5mA or less,
or if the terminals are suitably shrouded to prevent accidental contact with a live
conductor. Pupils must not be allowed to work on TV sets, open mains etc.
Rechargeable batteries
Rechargeable batteries (nicad, nickel metal hydride, lithium or lead-acid) may not
be used by young pupils in school (Y8 or lower) unless either the battery holder
and all electrical connections are completely inaccessible to pupils, or some
current limiting device is inserted between the batteries and the accessible
connections. This restriction is necessary because of the dangers of using thesebatteries. If they are short-circuited, the conducting wires can become red hot
and the plastic insulation will burn. If the short circuit is severe, high-capacity
batteries may explode. The risk of injury outweighs any cost-saving benefit. Nicad
or nickel metal hydride rechargeables may be used by pupils in Y9 or above
under suitable supervision when a low internal resistance power source is
necessary for a project to work. The pupils must be made aware of the hazards.
Owing to the risk of explosion, no attempt should be made to recharge primary
(non-rechargeable) batteries.
15
-
7/30/2019 H&S Manual West Sussex
16/68
|}~
Fire safety
Follow the school procedure for fire evacuation. Each room should have a notice
explaining the evacuation procedure and muster points. If there is more than oneexit, and one may lead people in the wrong direction to escape safely, a fire exit
sign with pictogram must be placed over the correct exit(s).
Each workroom should have the correct type and number of extinguishers and
other fire-fighting equipment as laid down by the local fire risk assessment.
Access to the equipment must not be hindered. Teachers and technicians are
advised to read the instructions on using the equipment. Refer to the health and
safety guidance on the WSGfL..
Fire hazards from highly combustible material require a specific risk assessment.
You need to look at how the fire could start, and put in specific safety measuresto reduce the likelihood of it happening and spreading. If you have concerns,
contact the Health and Safety Helpline on 01243 752025.
Fumes and dust
The COSHH regulations require that fumes and dust are kept below specified
limits specified. This can be done in several ways.
Change the process
Sometimes a simple change of technique can reduce dusts. Avoid keeping and
mixing fine powders if it is safe to keep them in paste or pellet form. Brush on
paints, glazes etc. rather than spray them. Consider hand-cutting plastics rather
than machining them.
Use natural ventilation
Activities which produce low levels of fumes, such as gluing with household
glues, soldering and painting with solvent based paints, can be done with no
special precautions other than ensuring good natural ventilation. This may meanworking near a window or working out of doors.
Use Local exhaust Ventilation (LEV) systems
Some processes produce high levels of fumes and dust and may only be done
with an adequate local exhaust ventilation system, also known as LEV, or fume
extraction or dust extraction. Where LEV has been installed, it must be tested to
check it meets the design criteria every 14 months. It is the establishments
responsibility to arrange for these tests; Education Supplies can advise you on
contractors. It is the responsibility of the subject leader to make sure the tests are
undertaken and that a record of these tests is kept.
16
-
7/30/2019 H&S Manual West Sussex
17/68
|}~
Use dust masks and respirators
These may only be used where it is impracticable to use methods 1-3, or when
methods 1-3 are not sufficient by themselves. It is not an alternative cheaper
method.
Refer to the CLEAPSS CD-ROM for Design and Technology for guidance on LEV
for dust and fume control for specific hazardous materials. Machines that produce
high levels of fine dust, such as disc sanders, belt-facers, circular saws, band
saws and powered fret saws must be fitted with suitable local exhaust ventilation.
Cleaning dusty areas
It is important that workspaces which are prone to the build up of dust - like wood
machining rooms and pottery rooms - are cleaned regularly, particularly in thenot-so-accessible places. Vacuum cleaners may only be used if they have
adequate dust filtering, eg a HEPA filter; ordinary vacuum cleaners will only
disperse very fine dust and cause a greater risk. Manual cleaning should be done
damp or wet, particularly silica dust in ceramics rooms. You may need to wear a
disposable dust mask (grade FFP2) if dust becomes airborne while cleaning. See
also the section on cleaning rooms.
Hazardous materials
The COSHH regulations (control of substances hazardous to health) require risk
assessments and control measures to be provided for employees and others
affected who have to work with hazardous substances, for example solvents,
acids, bleaches, dyes, etc which could be harmful if used wrongly. This includes
fumes and dusts. (COSHH is not concerned with dangers due to extremes of
temperature or pressure. Asbestos and lead are also excluded from the
regulations because there are separate regulations for these.)
COSHH is not designed to prevent teachers from using hazardous materials, it
should be regarded as a more systematic approach to sensible safe practicewhich has developed in schools and colleges over the years. Teachers and
technicians must refer to the COSHH risk assessments before using hazardous
materials, but there is no need for repeated referrals once they are familiar with
the hazards and safety procedures.Where reasonably practicable, you must use
less hazardous substances in preference to hazardous ones.
Be aware that the COSHH information is updated as new hazards are
recognised. You must not use a hazardous material if a safer substitute is
reasonably practicable.
17
-
7/30/2019 H&S Manual West Sussex
18/68
|}~
Risk assessments and control measures.
Many COSHH risk assessments for the materials used in practical subjects are in
the CLEAPSS CD-ROM for Design and Technology. If you are unable to obtain a
COSHH assessment, contact the Health and Safety Helpline on 01243 752025
with details of the product and the manufacturer and you will be supplied with
one. Do not use a hazardous material without an assessment. You must follow
the guidance given on the assessment.
To each risk assessment, you should add notes on any local conditions and
hazards. Every employee has a duty to make full and proper use of the safety
equipment and safety information provided by the school or the LA. The COSHH
information must be used in the planning and organising of technology activities.
People handling hazardous materials are also required to follow the
manufacturers or suppliers instructions for its use.
Local exhaust ventilation systems (LEV) have to be checked every 14 months.
Refer to the section fumes and dusts.
Prohibited substances
Some of the following materials may have been used in the curriculum in the
past, but they are no longer considered suitable. It is unlikely that these are in
schools now, but sometimes they turn up when clearing out old cupboards and
stores. Do not use them. This list is not exhaustive; no hazardous material may
be used unless it has been assessed carefully.
Prohibited Substance Likely use
Asbestos Heat insulation
Benzene Solvent
Barium powder pigments Paint/glaze colouring
Cadmium powder pigments Paint/glaze colouring
Chromium powder pigments Paint/glaze colouring
Fehlings solution Food test
Hydrofluoric acid Etching glass etc.
Methanal (formaldehyde, formalin) Fungicide, lithography
Millions reagent Food test
Phenol (solid) Anti-bacterial investigations
Raw lead glazes Glazing ceramics
Tetrachloromethane (carbon tetrachloride) Solvent, stain remover
ICT equipment
Although working with display screen equipment is not generally high risk, userscan get musculoskeletal and other physical problems, eye fatigue and mental
18
-
7/30/2019 H&S Manual West Sussex
19/68
|}~
stress if they do not follow the precautions laid down in the Display Screen
Equipment (DSE) regulations2. These regulations are relevant to staff,
particularly those in information technology areas. Children are not normally
classed as users because they do not use the DSE equipment for long enough.
Nonetheless, the general principles in setting up comfortable and low-risk
workstations for children should still be followed.
Safe use of laptop computers
Laptops and similar portable computers are not suitable as office workstations for
clerical and administrative support staff. These styles of computers have smaller
keyboards and screens than desktop computers and this makes them less
comfortable to use, especially over longer periods. The hazards are aches and
pains caused by poor posture, eyestrain and headaches from looking at a poor
contrast screen, and arm and finger strains caused by poor keyboard technique.There is also an electrical hazard if the laptop external power unit becomes
damaged.
Follow these points to reduce the health hazards:
Avoid using laptop computers for long periods; use a full-sized PC if one is
available or consider using a docking station with a plug-in full size mouse and
keyboard.
When you use mains power, only use the a.c. adaptor provided by the
manufacturer, not any others, to avoid incompatibility and damage to the laptop.
Look at the adaptor, power cables and plug, and check that they are in good
condition before plugging in. Keep the power cables free from twists.
If possible, choose software that allows you to adjust image size and colour.
Be careful that power cables do not cross walkways because it may cause
someone to trip.
When you use a laptop for more than a few minutes, make sure you are sitting
comfortably with good posture, and adjust the screen to give the best viewing
position without screen reflections. It is better to use the laptop on a table rather
than on your lap.
Take regular breaks from using the laptop if the work is prolonged. As a guide, do
something else for five minutes every thirty minutes of laptop use.
Practical rooms are far from ideal for ICT equipment, so extra care is needed.
Ensure that the equipment is placed in a dust-free area and well away from
water, solvents, hazardous liquids etc. Dust and dirt will damage CD drives. Do
not place the equipment close to radiators or other heat sources. Ensure that the
2 The Health and Safety (Display Screen Equipment) Regulations 1992.
19
-
7/30/2019 H&S Manual West Sussex
20/68
|}~
ventilation holes remain unobstructed. Arrange the equipment so that users are
able to sit down and operate it comfortably.
Refer to the section Electricity. Computer equipment is likely to have many
trailing leads used for connecting the peripheral equipment. Route these leads tominimise the risk of someone becoming entangled in them.
Some desktop PCs have a significant earth leakage to cause nuisance tripping of
sensitive RCDs. Double insulated equipment such as laptops will not cause this
problem.
Visual disp lay units (VDU)
The VDU should be used in a shaded area of the room, not in bright light, so that
it is comfortable to view. Keep the screen clean by wiping it with a dry clean cloth.
Interactive whiteboards
The height of the board from the floor should be set to give good visibility and
ensure users can reach all areas of the board without having to bend excessively;
the height should also give children access to a sufficient area of the board.
Avoid using platforms to give younger children access to the board.
The light from projectors is very bright and can cause eye damage. Follow these
guidelines to prevent this.
Never stare directly into the beam of the projector. Warn children of the dangers
too.
When entering the beam, you should not look towards the class for more than a
few seconds.
As much as practicable, keep your back to the projector beam when you move
into the beam.
Children should be supervised when the projector is in use.
Interactive whiteboards can be very difficult to see when direct sunlight shines on
the board. If the board is in direct sunlight, you will need to fit window blinds. Staff
adjusting or cleaning a high-mounted or suspended projector must use anappropriate step ladder or kick stool to access it safely. Projectors should be
allowed to cool down before cleaning.
All cabling must be safely secured safely for the whole of the cable length.
20
-
7/30/2019 H&S Manual West Sussex
21/68
|}~
Ladders, steps and other access
equipment
You must have suitable ladders and other portable access equipment (PAE) for
staff who need to work at heights, for instance to put up displays or reach upper
shelves. Chairs, tables and so on must not be used. Stepladders, ladders and
scaffold towers must be suitable for the tasks. Wooden ladders must meet
BS1129: 1990, metal ladders must meet BS 2037:1994, or the European
equivalents. Ladders should be Class 1, designed for industrial use. Avoid
ladders designed for light or domestic use.
The subject leader must ensure that:
The access equipment is in good condition and checked at least every year. The access equipment is stored safely and securely so unauthorised people
cannot use it.
Staff and other users know how to use it properly.
Follow the guidance in the HSE leaflet Safe use of ladders and stepladders: an
employers guide. Access equipment must be checked regularly. One way of
arranging this is to make sure each item of equipment has an owner responsible
for checking it regularly, and taking it out of service if it becomes defective.
Records of checking must be kept.
Staff must be given training so they can use access equipment safely. The type
of training must depend on the risks. Staff who are expected to use access
equipment regularly must attend a suitable formal training course; contact the
Health and Safety Helpline, 01243 752025, for details.
People who erect, use and dismantle mobile scaffolding units must be properly
trained and qualified to do it safely. The qualification should be to a PASMA
(Prefabricated Access Suppliers and Manufacturers Association) standard.
Lifting operations and l ifting equipment
These are regulated by the Lifting Operations and Lifting Equipment Regulations
(LOLER). These regulations apply to all hoists, jacks or other lifting equipment
that may be used in technology. If you have any such equipment, then you must
ensure that the lifting equipment is:
of adequate strength and stability for each load, particularly regarding the stress
at its mounting or fixing point;
21
http://indg402.pdf/http://indg402.pdf/http://indg402.pdf/http://indg402.pdf/ -
7/30/2019 H&S Manual West Sussex
22/68
|}~
positioned or installed to reduce to as low as is reasonably practicable the risk of
the equipment or a load striking a person; or from a load drifting, falling freely, or
being released unintentionally;
either marked to indicate its safe working load, or has information kept with themachine that clearly indicates its safe working load for each configuration, or both
if it applies;
is thoroughly examined regularly.
For lifting equipment for lifting persons or an accessory for lifting, the regulations
specify the equipment must be examined at least every 6 months, and for other
lifting equipment, at least every 12 months; or in either case, in accordance with
an examination scheme, and each time that exceptional circumstances have
occurred that could have damaged the lifting equipment.
The examination must be done by a competent person, and will normally involve
a load test. Teachers or technicians could carry out the examination provided
they have been given the appropriate training and test equipment. Whoever
carries out the examinations, you must retain records of dates and results of the
examination.
See also the section on manual handling.
Lone workingLone working means working when there is nobody else around to help or to
raise the alarm if you need it. For example, a teacher might come into school on
their own at the weekend to prepare some work.
If staff need to work alone, you must consider what precautions you need to take
for their health and safety. This begins before they even arrive for work: it is
important that someone else knows that they will be working alone, and
approximately when he or she should be home. For practical purposes, this could
be a relative, friend or neighbour.
When they are at work, the normal standards apply so that potential harm is kept
to a minimum. But lone workers also have to remember that they are responsible
in law for their own health and safety they must not take risks or short cuts.
They must not try to do anything they are not adequately trained for, or which
needs more than one person to do it safely.
Anyone with supervisory responsibilities must do a risk assessment identifying
the hazards, assessing the risks involved and putting the measures in place to
avoid or control them. This means identifying situations where their staff work
alone, and considering a number of questions.
22
-
7/30/2019 H&S Manual West Sussex
23/68
|}~
Does anything about the environment present specific risks to staff eg the
location, weather conditions or time of year?
Is there safe access in and out?
Can the equipment be safely handled and used by one person?
Does the job involve handling loads?
Is there a risk of violence?
Do the staff concerned have any medical conditions?
What forms of communication are available?
The risk assessment may point out a need for more staff, equipment, information,
instruction and training, greater supervision, or new safer systems of work such
as a checking-in system.
The Health and Safety Team run personal safety courses regularly. Contact them
on 01243 752025 for details.
Management of health and safety
This manual is not meant to be alarmist and there is no intention of deterring
teachers from introducing new activities provided that any hazards can be
approached in a safe way. In a world full of dangers it is important for the pupils
to learn how to recognise the hazards and manage them safely. Generally,
schools are very safe places. However, risks must be made as low as reasonably
practicable. All staff have a duty to use the safety information to minimise risks to
themselves, to pupils and to others. Teachers are expected to use this
information to help them to plan lessons and decide if an activity can be carried
out safely, giving consideration to the age and responsibility of the pupils.
In the event of an accident, it is important that immediate interim measures are
taken (if needed) to prevent a recurrence. Accidents must be reported in
accordance with the instructions from the LA.
Risk assessments
See also the section on Pupils with special educational needs.
Risk assessment is a process for looking at what can cause harm, how likely and
severe the harm could be, and what can be done to prevent it. There is no such
thing as zero risk risk assessment is a way of reducing the risks to an
acceptable level, so the benefits of the activity far outweigh the risks. All activities
that involve foreseeable significant hazards must have a risk assessment before
it is undertaken. Do not carry out any such activity without a risk assessment.
23
-
7/30/2019 H&S Manual West Sussex
24/68
|}~
As the activities in technology and art are unlikely to vary greatly from one school
to another, generic risk assessments can be used. Generic risk assessments for
most activities are in this manual and in the associated supporting documents
explained in the introduction, particularly those produced by CLEAPSS,and
BS4163:2007. Your schemes of work must be marked to show the hazards, and
where staff or pupils can find the risk assessments. Similarly, lesson plans, pupil
worksheets, text books etc should be marked similarly. Where there are special
local conditions that create hazards not on the generic risk assessment, you
should adapt the risk assessment accordingly, adding steps to reduce the local
hazards.
When pupils are planning projects and coursework, staff should help them to
identify the hazards that are likely to be encountered and the steps they will take
to reduce the risks adequately.
Do not forget to involve Teaching Assistants and voluntary staff in your risk
assessments. They should be consulted when considering pupils with special
needs so that all pupils and staff have adequate levels of protection from the
hazards in the practical curriculum.
There is more information on risk assessments on the health and safety pages of
WSGfL. If you need further advice on risk assessments, for example if you are
undertaking or supervising a special project, contact the Health and Safety Team,
01243 752025, or the relevant Adviser from Adults and Children - Learning.
Keeping records
Subject Leaders must keep records to demonstrate that health and safety is
being managed correctly. The records include:
Machinery maintenance.
14 monthly LEV tests.
Gas appliance annual tests.
Room and equipment termly checks.
Staff training (and certificates such as those for food safety, circular saws,planer/thicknessers, welding).
When portable appliance electrical testing was undertaken.
When inspection of fixed electrical installation was undertaken.
Pressure vessel inspections & tests.
Lifting equipment annual inspections & tests.
Access equipment (eg stepladders) inspections.
24
-
7/30/2019 H&S Manual West Sussex
25/68
|}~
Some of these inspections and tests are likely to be organised centrally by the
school and records kept by the Premises Manager or Bursar. It is important the
Subject Leader receives copies of these records.
Health and safety pol icies
To achieve good management of health and safety, subject leaders and staff are
expected to co-operate with the senior management of the school or college on
health and safety matters. Each school has an overall Health and Safety Policy
that explains how adequate standards of health and safety will be achieved it is
the responsibility of the Head and Governors to prepare it. Subject leaders will
normally have delegated responsibility for ensuring adequate health and safety
standards in their departments. It is very useful if practical departments have a
subsidiary health and safety policy to detail the departmental health and safety
arrangements.It is a requirement of the LA that departments undertaking practical work (which
includes Design and Technology, Art and Design, Ceramics, Textiles and Food
Technology) have a written subsidiary health and safety policy that clearly and
concisely explains the departmental health and safety arrangements. This could
be a combined policy that covers a range of practical curriculum areas, or
individual policies in which each covers a specific practical curriculum area. In
larger departments, many health and safety functions will be delegated. It must
be clear from the departments safety policy what safety functions have been
delegated, and to whom. The policy should have four sections;
A general statement of commitment and intent.
This is a short paragraph that expresses the departments commitment to health
and safety and the intent to make teaching as safe as is reasonably practicable.
Department's organisation
This is a description of the departments organisation for achieving their
commitment. This should explain the structure of the department and the line
management from the overall head of the department to all other people who
work in the department. This section should explain the formal ways in which
health and safety information is communicated to and from staff. The LA
recommends that time be allocated formally at staff meetings to exchange
information on health and safety. Minutes of a meeting can form a record of
information passed to staff.
The particular arrangements for implementing the policy.
This should state the model risk assessments the department will adopt and how
staff will use the information. The risk assessments are the CLEAPSS CD-ROM
for Design and Technology, BS 4163:2007, and the NSEAD A Guide to Safe
Practice in Art and Design, as appropriate. This section should also explain all
health and safety duties delegated by the subject leader, such as the person
responsible for ensuring schemes of work have appropriate risk assessments,the person who oversees the induction for new staff including technicians, the
25
-
7/30/2019 H&S Manual West Sussex
26/68
|}~
people who check the machinery, tools and rooms, etc. The arrangements for
testing of particular items should also be explained, such as checking fume
extraction, gas appliances, pressure systems, gas cylinders and regulators, and
protective equipment such as goggles and face shields. There must be a
procedure for making sure the health and safety functions are undertaken; part of
the procedure must be a plan of what will be done to rectify faulty equipment and
machinery.
Monitoring and reviewing
This section should explain the arrangements for monitoring and reviewing the
health and safety of the department.
The document should be signed and dated by the subject leader and approved
by the head and governing body. The policy does not need to be long; the length
will depend on the departmental complexity, but try to keep it to a few sides ofA4. The document should not include particular risk assessments or other codes
of practice - it is not a document on the particular safety measures for each
practical work undertaken.
Practical activities must be assessed for risk, and safety measures used to keep
the risks low. If you are undertaking any new activities, it is essential that a risk
assessment is carried out beforehand. Consult experienced colleagues, Adults
and Children - Learning or the Health and Safety Team to help you determine the
significant hazards and the risk of them happening. From this, decide on suitable
control measures to minimise the risks.
Responsibilities
Health and safety is not the responsibility of just one person. The duty of care is
on all employees and pupils to look after their own welfare and the welfare of
others who may be affected by their actions; the responsibility for health and
safety is no less important than any other function. Your employer also has
responsibilities for health and safety, including a duty to protect you, provide
training and keep you informed about health and safety matters. As part of the
LAs obligations, this file provides guidelines on safety in technology practical
work. Problems regarding this information should be discussed and brought to
the attention of the School Support Service where relevant. Subject leaders have
a duty to organise the department so that staff have access to the health and
safety information and understand the system for reporting defects in safety
equipment. No activity may be carried out unless the requisite health and safety
apparatus is available and in good working order. Every technology department
must have procedures for:
Making sure risk assessments are undertaken and used;
giving information to the people who need it;
ensuring regular safety checks are undertaken;
26
-
7/30/2019 H&S Manual West Sussex
27/68
|}~
keeping rooms clean and tidy;
reporting defective equipment;
ensuring apparatus receives necessary maintenance; and
ensuring only suitably qualified staff use restricted machinery.
A safety policy is a good way of showing how these procedures are organised in
the department. See the section Safety Policies
Class sizes
There is no statutory limitation on class size in any subject in schools in England
and Wales. Teachers who are concerned that the class size presents an
unacceptable risk to health and safety should report their concerns to their
subject leader and if necessary, the head teacher. Use alternative methods ifpossible for particular practical activities to reduce the risks, but if they cannot be
lowered to an acceptable level, the activities must not be undertaken until the
health and safety matters have been resolved. Adults and Children - Learning
and the Health and Safety Team can give advice.
British Standard 4163:2007 recommends class sizes of no more than 20 per
competent, qualified teacher. For numbers higher than this, follow the British
Standards guidance (BS 4163:2007 Section 3) and carry out a risk assessment.
When deciding class size, it is the policy of the LA that there must be an
identifiable unshared suitable workspace per pupil in the practical room. This
means a suitable bench or table area (with a seat where relevant). In a machine
workshop, the workspace must have a vice.
Use the guidance in Building Bulletin 81, Design and Technology
Accommodation in Secondary Schools: A Design Guide, or DfEE Building
Bulletin 89, Art Accommodation in Secondary Schools, as appropriate for
planning class sizes and work space, and take into account:
room size and layout,
the equipment in the room,
the type of activities to be undertaken,
competence and experience of the teacher,
bench space, space between benches
class behaviour, and
pupils with special needs.
Using workrooms
Staff are expected to leave workrooms in a safe condition. When starting apractical lesson, staff should check that rooms are clear, all thoroughfares and
27
-
7/30/2019 H&S Manual West Sussex
28/68
|}~
room exits are free from obstruction, floors are dry and in a safe condition, and
the lighting is adequate for the work being undertaken. Fire doors must be
unlocked and clear. Only staff authorised by the subject leader are permitted to
switch on the electricity and gas mains isolators, pupils may not switch on these -
not even under supervision. The department must ensure that pupils do not use
utensils, tools, machines or other equipment until they have been taught how to
use them correctly. Only one person may operate a machine or piece of
equipment at a time (there are some exceptions - see part II), some machinery is
restricted to use by qualified staff (again, see part II). Pupils are required to clear
away at the end of each practical session. Where possible, keep practical rooms
locked when not in use.
Normally, workshops, food technology rooms and other specialist practical rooms
should be locked when not in use. A specialist room should only be used for the
purposes for which it was designed.
Delivery of lessons
The Local Authority recommends that all design & technology lessons, and art &
design lesson, are delivered under the direction of qualified teachers who have
the skills, expertise and experience required to teach the work safely. For other
arrangements, Heads are advised to obtain advice from Adults & Children
Learning because there are statutory restrictions that affect the choice of who
may deliver lessons to pupils.
For Learning Support staff working under the direction of the teacher, the teachermust liaise with them beforehand to ensure that the Learning Support staff
understand the risk assessment for the practical work to be undertaken. The risk
assessment must include the health and safety of the Learning Support staff,
including any provision of suitable personal protective equipment identified by the
risk assessment. See also the section on pupils with special educational needs.
For guidance on the role of Learning Support staff, refer to the WSGfL Support
Staff.
Cover supervisors
Cover supervisors (including teachers acting as cover supervisors) must be giveninformation on the practical room hazards; this could be a laminated A4 sheet for
the room explaining the location and operation of main services such as
electricity and gas isolators, any local hazards, and where help can be obtained.
Subject Leaders must make sure that pre-set learning activities for cover
supervision have no practical element (but simple practical work that a risk
assessment has shown to be negligible risk3 is acceptable). The room gas supply
and machine electricity supplies should be switched off (preferably locked off).
3 This is to allow routine work such as the use of paper glue and blunt-ended scissors.
28
-
7/30/2019 H&S Manual West Sussex
29/68
|}~
Tutor/form rooms
Machine workshops must not be used as tutor or form rooms. Other practical
rooms may be used as a last resort; a risk assessment must be undertaken
beforehand.
Maintenance of equipment and practical rooms
See also the section on electricity.
There is a statutory requirement to maintain machinery. The regulations are quite
extensive. Among other things they require machinery to be in efficient working
order and in good repair, with relevant safety devices functional. Keep machine
guards in clean and good condition, those that have safety interlocks must be
checked regularly to ensure that they work efficiently. Some equipment has
statutorily specified test and maintenance intervals (se the subsection Keeping
records). The law requires equipment to be checked regularly enough to preventdangerous conditions occurring. For most machines, the scheduled maintenance
should be done at least annually. Maintenance procedures should be carried
according to the manufacturers recommendations which relate to the equipment,
for example the periodic lubrication, replacement and adjustment of parts. You
must keep records of the maintenance.
You should identify three levels of equipment checks:
Level 1 a visual check whenever the equipment is used.
Level 2 termly room and equipment check must be recorded and actionstaken where needed.
Level 3 annual check and maintenance usually carried out by an external
contractor.
In this booklet there are checklists for workrooms (workshops, pottery rooms
etc.). There is no obligation to use them, but departments must have some
procedure for making safety checks. The checks need to be done at least once a
term, they must be carried out by a person who understands the nature of the
hazards associated with the activities carried out in the room. Part of the checklist
is blank so that you can make your own additions.
Safety signs, notices and displays
Each workroom must have a set of safety rules and the fire procedure displayed
clearly. Cautionary notices and signs must be displayed where appropriate,
these can be home-made provided they conform to current standards and
standard pictograms and are made of a durable material.
Making artefacts
Items made at school must be safe to use. In many cases, there are regulations
or guidelines such as The Toys (Safety) Regulations and The Magnetic Toys(Safety) Regulations. Items must not be dangerous on account of their
29
-
7/30/2019 H&S Manual West Sussex
30/68
|}~
flammability; they should be made inflammable or, if they can ignite, should burn
slowly with a small rate of flame spread.
Manual handling
Manual handling covers any form of lifting, pushing, pulling or carrying loads, by
hand or using bodily force. Handling loads using incorrect techniques can cause
strains particularly back strain fractures, cuts and other injuries.
These can mean lost working days, and in severe cases even permanent
disablement. Injuries caused by bad manual handling are a big cause of absence
in education. So subject leaders must:
tell staff to avoid manual handling where there is a significant risk of injury,wherever reasonably practicable
assess all manual handling operations where there is a significant risk of injury;
4 record all relevant assessments;
review the assessments regularly; and
provide adequate information, instruction and training for staff.
Noise
Noise levels at work are regulated by The Noise at Work Regulations. Some
machines can produce high levels of sound, for example circular saws, planers,
and percussion drills. The lower exposure action values is a daily or weekly
personal noise exposure of 80 dB(A) (and a peak sound pressure of 135 dB(C)).
To give an idea of this loudness, you would have to raise your voice to make
yourself understood over this level of noise to a person standing two metres
away. If you are experiencing noise at this level, you may need to implement
controls under these Regulations to reduce the noise level or protect yourhearing; contact the Health and Safety Helpline, 0243 752025, for advice.
If you notice regular ringing in your ears after being in a noisy environment,
obtain advice from the Health and Safety Helpline.
4 There are occasions when an assessment does not need to be recorded: if it couldeasily be repeated and explained at any time because it is simple and straightforward,or the manual handling operation is straightforward, the risk is low, or it is only going tolast a very short time so the time taken to record it would be out of proportion to thetask involved.
30
-
7/30/2019 H&S Manual West Sussex
31/68
|}~
Pupils with special educational needs
Pupils with SEN are entitled to education in design & technology, including
practical work. Pupils with special needs can present health and safetyimplications for teaching practical work that need to be resolved. The approach
must be through risk assessment; this ensures the pupil has access to the
curriculum without undue risk to their health and safety and to that of others.
Do not overlook the health and safety of support staff working with pupils with
SEN - it is important to discuss the risk assessment with support staff
beforehand, including safety measures for their own health and safety.
You can obtain help with risk assessments from Adults and Children Learning
and the Health and Safety Team. You must implement the health and safety
measures identified by the risk assessment.
Pressure systems
Large compressed air systems (in which the pressure multiplied by the internal
volume of the air receiver exceeds 250 bar litre) are regulated by the Pressure
Systems Safety Regulations. You must arrange for the regular examination of
such pressure equipment by a competent person.
All pressure systems must be maintained in good repair to prevent danger. Usersmust know what action is needed in the event of an emergency, in most cases
this will be to remove the source of energy (switch off the electrical supply, turn
off the heat etc.) and leave the area.
Users of any pressure system should carry out pre-start checks, they should
understand under what circumstances the system should be shut down and know
how to vent any residual pressure safely before removing lids, filler caps, hoses
etc.
If the pressure vessel shows any signs of significant pitting, corrosion, damage
from drops or knocks or bowing from over-pressure, it should be considered
sufficient grounds for replacing the apparatus.
Regardless of the size of the system, it would still be wise to make regular spot-
checks. Ensure that all hoses and pressure pipes are in good condition and
securely fitted. The compressed air vessel should be free from corrosion or other
visible signs of damage. Check that the pressure gauges are working and the
pressure cut-out switch operates. Filters should be serviced regularly and
water/oil trap bowls should be clear and free from cracks. Where appropriate, the
compressed air vessel should be marked clearly with the maximum safe working
pressure.
31
-
7/30/2019 H&S Manual West Sussex
32/68
|}~
Do not neglect the non-pressure hazards like power cables, drive belts and
guards. If portable air compressors are mounted above the floor surface, they
must be secured before they are used.
Under no circumstances should compressed air be used for blowing away dust.
Hired pressure systems
The owner has the responsibility for carrying out the formal examination and the
hirer has the duty to use the system in accordance with the manufacturers
instructions.
Model stream engines.
These are included in the Pressure Systems Safety Regulations. CLEAPSS has
produced a scheme of examination for pressure cookers, autoclaves and model
steam engines. The formal examination