Introduction to TactoTek Injection Molded Structural Electronics - IMSE
How we designed an injection-molded case
Transcript of How we designed an injection-molded case
![Page 1: How we designed an injection-molded case](https://reader031.fdocuments.in/reader031/viewer/2022012409/616a472a11a7b741a350c29a/html5/thumbnails/1.jpg)
How we designed an injection-molded caseCreated by Mike Doell
Last updated on 2018-08-22 03:41:28 PM UTC
![Page 2: How we designed an injection-molded case](https://reader031.fdocuments.in/reader031/viewer/2022012409/616a472a11a7b741a350c29a/html5/thumbnails/2.jpg)
236789
10121415
Guide Contents
Guide ContentsPreparationDesignPrintTweak, print, repeat.RenderCreating an injection moldMold testingFinal fit checkFinished part
© Adafruit Industries https://learn.adafruit.com/how-we-designed-an-injection-molded-case-for-raspberry-pi Page 2 of 16
![Page 3: How we designed an injection-molded case](https://reader031.fdocuments.in/reader031/viewer/2022012409/616a472a11a7b741a350c29a/html5/thumbnails/3.jpg)
Preparation
Hi there, Mike Doell here! I designed the Adafruit Pi Case and took a few screenshots and photos along the way. Thistutorial will go through the process I undertook to design this injection molded case.
Gather all of the relevant cables, sd cards etc that may be used with the board. Put all the things that may be pluggedinto the board in place.
This gives us an idea of what to look out for as we generate ideas and highlights possible interference between the
© Adafruit Industries https://learn.adafruit.com/how-we-designed-an-injection-molded-case-for-raspberry-pi Page 3 of 16
![Page 4: How we designed an injection-molded case](https://reader031.fdocuments.in/reader031/viewer/2022012409/616a472a11a7b741a350c29a/html5/thumbnails/4.jpg)
case and the parts.
Time to start measuring components and building them in CAD. Here is a drawing of the raspberry pi that was built in3D, to use as an underlay while designing the case.
Sometimes you're lucky and there's a CAD file available to use as a 'negative' - but sometimes we're not so lucky!
Next step is to build and assemble all of cables in 3D. This helps make sure we have plenty of clearance forovermolding, etc. Try to get the chunkiest cables people may end up using
© Adafruit Industries https://learn.adafruit.com/how-we-designed-an-injection-molded-case-for-raspberry-pi Page 4 of 16
![Page 5: How we designed an injection-molded case](https://reader031.fdocuments.in/reader031/viewer/2022012409/616a472a11a7b741a350c29a/html5/thumbnails/5.jpg)
© Adafruit Industries https://learn.adafruit.com/how-we-designed-an-injection-molded-case-for-raspberry-pi Page 5 of 16
![Page 6: How we designed an injection-molded case](https://reader031.fdocuments.in/reader031/viewer/2022012409/616a472a11a7b741a350c29a/html5/thumbnails/6.jpg)
Design
Once the components are in position, ideas are generated by sketching over printouts or building simple shapesdirectly in CAD.
© Adafruit Industries https://learn.adafruit.com/how-we-designed-an-injection-molded-case-for-raspberry-pi Page 6 of 16
![Page 7: How we designed an injection-molded case](https://reader031.fdocuments.in/reader031/viewer/2022012409/616a472a11a7b741a350c29a/html5/thumbnails/7.jpg)
After the parts are mocked up in CAD the first parts are printed for a fit check.
At this point we are looking for potential interference and evaluating details like parting lines.
This was an original revision, without the sloped top.
You can use a 3D printer for this, or send it it out to a 3D printing service. 3D printers have gotten good enough toprovide snap-fit resolution!
© Adafruit Industries https://learn.adafruit.com/how-we-designed-an-injection-molded-case-for-raspberry-pi Page 7 of 16
![Page 8: How we designed an injection-molded case](https://reader031.fdocuments.in/reader031/viewer/2022012409/616a472a11a7b741a350c29a/html5/thumbnails/8.jpg)
Tweak, print, repeat.
Now the fun starts! Refining fit, adding/ removing details. Getting the 'feel' of the case
Making sure you have access to all of the connectors can be challenging - especially with a board like the Pi that hasconnectors on all sides!
© Adafruit Industries https://learn.adafruit.com/how-we-designed-an-injection-molded-case-for-raspberry-pi Page 8 of 16
![Page 9: How we designed an injection-molded case](https://reader031.fdocuments.in/reader031/viewer/2022012409/616a472a11a7b741a350c29a/html5/thumbnails/9.jpg)
Render
After sorting out the fit and finish we start rendering to figure out the materials and colors. Different materials will affectcost and mold design so its best to get a good idea of what you want early.
© Adafruit Industries https://learn.adafruit.com/how-we-designed-an-injection-molded-case-for-raspberry-pi Page 9 of 16
![Page 10: How we designed an injection-molded case](https://reader031.fdocuments.in/reader031/viewer/2022012409/616a472a11a7b741a350c29a/html5/thumbnails/10.jpg)
Creating an injection mold
This is the steel we will use to create the inserts for the injection mold. We create an insert for the core and cavity (top and bottom in this case) of each part.
© Adafruit Industries https://learn.adafruit.com/how-we-designed-an-injection-molded-case-for-raspberry-pi Page 10 of 16
![Page 11: How we designed an injection-molded case](https://reader031.fdocuments.in/reader031/viewer/2022012409/616a472a11a7b741a350c29a/html5/thumbnails/11.jpg)
The shapes are roughed into the inserts on the CNC.
Fine details like snap catches are burned into the inserts using a copper electrode on an EDM machine.This gives detail that is too small to be machined with a cutter.
© Adafruit Industries https://learn.adafruit.com/how-we-designed-an-injection-molded-case-for-raspberry-pi Page 11 of 16
![Page 12: How we designed an injection-molded case](https://reader031.fdocuments.in/reader031/viewer/2022012409/616a472a11a7b741a350c29a/html5/thumbnails/12.jpg)
Mold testing
This is the core side of the tool, it creates the inside of the parts. This is also the side that the ejector pins are on. The pins push the part out of the tool and they also leave the small round dots you see on the inside of a molded part.The hoses are used to move water through the mold base and keep everything at a constant temperature.
© Adafruit Industries https://learn.adafruit.com/how-we-designed-an-injection-molded-case-for-raspberry-pi Page 12 of 16
![Page 13: How we designed an injection-molded case](https://reader031.fdocuments.in/reader031/viewer/2022012409/616a472a11a7b741a350c29a/html5/thumbnails/13.jpg)
This is the cavity side of the tool, it creates the outside or "show side" of the parts.On opaque parts this is the half that gets polished.*Unless your part is clear then the core and cavity will have the same finish.
Once we get the tool installed we create our test shots.They are typically clear, it makes it easier to see whats happening during fit tests.
© Adafruit Industries https://learn.adafruit.com/how-we-designed-an-injection-molded-case-for-raspberry-pi Page 13 of 16
![Page 14: How we designed an injection-molded case](https://reader031.fdocuments.in/reader031/viewer/2022012409/616a472a11a7b741a350c29a/html5/thumbnails/14.jpg)
Final fit check
Final fit check with board in place.
We always make things "tool safe" which means thateverything is slightly loose.It is easier to remove material from the tool by machining when you need to tighten it up.When the parts are too tight or there is an interference you will need to weld the tool (adding material by welding) andremachining or by cutting a pocket in the area that needs to be changed and filling it with material that can bemachined again (referred to as "inserting" the tool).
© Adafruit Industries https://learn.adafruit.com/how-we-designed-an-injection-molded-case-for-raspberry-pi Page 14 of 16
![Page 15: How we designed an injection-molded case](https://reader031.fdocuments.in/reader031/viewer/2022012409/616a472a11a7b741a350c29a/html5/thumbnails/15.jpg)
Finished part
Final production parts.
If you look closely at the corner of the clear cover you can see a small round dot. That's from the ejection pin when itpushes the part out of the tool.
© Adafruit Industries https://learn.adafruit.com/how-we-designed-an-injection-molded-case-for-raspberry-pi Page 15 of 16
![Page 16: How we designed an injection-molded case](https://reader031.fdocuments.in/reader031/viewer/2022012409/616a472a11a7b741a350c29a/html5/thumbnails/16.jpg)
© Adafruit Industries Last Updated: 2018-08-22 03:41:23 PM UTC Page 16 of 16