JANUARY 2019

Rockwell Unscripted®

Creative Wall®

HOW TO SPECIFY DRAPERY

Creative Wall Measurements

90" 86"87"

Configuration ACrossbeam and drapery trackbetween walls or columns.

87" to floor

72" Opening

Configuration BChannel in headerbetween end of walls.

86" to the floor

This guide provides the necessary information to order KnollTextiles prefabricated ripple fold drapery panels for the Rockwell Unscripted Creative Wall. All KnollTextiles drapery products are approved for use with Creative Wall.

3 Key Points:

1. Place your Rockwell Unscripted system order with Knoll Office. The drapery track is included in your Knoll Office order.

2. Place your drapery order with KnollTextiles.

3. Include the drapery fabri-cation kit part number(s) on your KnollTextiles drapery Purchase Order.

STEP 1 VERTICAL CONFIGURATIONWhich Rockwell Unscripted Creative Wall configuration have you ordered?

STEP 2 HORIZONTAL CONFIGURATIONa. What is the width of the Creative Wall opening?b. How many panels will cover the opening?c. Divide the opening size by the number of panels.

Note: Vertical configuration does not account for uneven floors.

HOW TO SPECIFY DRAPERY: ROCKWELL UNSCRIPTED® CREATIVE WALL®

See Drapery Specification for yardage requirements based on panel size. If panel size is not standard, round up to assure full coverage.

Example: A 72" opening is to be covered with 2 drapery panels, divide 72" by 2 = 36". You require qty. (2) 36" panels.

Per panel drapery yardage requirements:2.5 yards of wide width drapery or 7 yards of standard width drapery

90" 86"87"

36"

36"

36" 48" 60" 72" 84" 96"

87"A/B

Drapery FullnessDrapery fullness refers to the quantity of fabric needed to make the drapery treatment. KnollTextiles fabricates drapery panels at 100% fullness for Rockwell Unscripted Creative Wall.

• 0% fullness is the amount of fabric needed to cover the opening.

• 100% fullness is double that amount.

Different yardage estimates are required for orders of 10+ panels of the same drapery fabric.

Custom sized panels are available. Please contact your local KnollTextiles sales representative for information.

Drapery Specifications

36" 2.5 yds 7 yds

48"  3.5 yds 10 yds

60" 4 yds 10 yds

72" 5 yds 10 yds

84" 5.5 yds 13.5 yds

96" 6 yds 13.5 yds

Drapery Panel Size at 100% Fullness

Wide Width Railroaded (Seamless)

Standard Width (Seamed)

STEP 3 YARDAGE REQUIREMENTSDrapery width and fabricated panel size determine the required drapery yardage at 100% fullness.

Railroading Wide Width Fabric Wide width drapery (110" or over) is intended to be used railroaded to avoid seaming panels together. By turning the drapery 90 degrees, (the width of the fabric becomes the length), the drapery can span any horizontal distancewith a seamless appearance.

DRAPERY PANEL OPTIONS

When measurement of drawing changes (see note below) the part number changes to: Quantity (2) KT-UD-FK-87-36

Example of a drapery panel kit order number Quantity (2) KT-UD-FK-87-72

JANUARY 2021

FOLLOW THESE STEPS TO PLACE YOUR KNOLLTEXTILES FABRICATION KIT(S) ORDER

1 Order cut yardage from KnollTextiles based on yardage estimates in Drapery Specifications.

2 Order Fabrication Kit. Part numbers are found in the chart and follow the logic: KT-UD-FK-(Length-Width) Note: Refer to vertical & horizontal configuration guides to assure correct measurements.

3 Order baton if desired. Clear Plexiglas baton mounts between the first and second snap on either side of the finished drapery.

Ordering Process and Part Numbers

Drapery panels are shipped folded, please install and steam promptly. KnollTextiles will not provide field measurements or installation of the drapery kits.

There is a 24-hour cancellation period from the time of PO confirmation from KnollTextiles.

Purchase orders for cut yardage and fabrication kits should be submitted to KnollTextiles:

Phone: 866.565.5858Email: Textiles_orders@knoll.comFax: 866.565.5860

Shipping cost estimate based on yardage can be obtained from KnollTextiles customer service.

Finished drapery panels will be shipped to the given ‘ship to’ address fifteen (15) days after the workroom receives the fabric.

CONFIGURING PART NUMBERS KT-UD-FK IS THE BASE OF EVERY PART NUMBER. ADD HEIGHT (CONFIGURATION A OR B) AND WIDTH TO COMPLETE THE PART NUMBER FOR EACH PANEL.

USA $22

CAN $34

Baton w. slide

Configuration BKT-UD-FK-86

86" to floor

87" 36" $220 $293

87" 48"  $290 $387

87" 60" $360 $480

87" 72" $435 $580

87" 84" $575 $767

87" 96" $645 $860

87" 114" $886 $1,181

87" 120" $980 $1,307

87" 128" $1,056 $1,408

87" 176" $1,168 $1,557

L W

USA

CAN

Configuration AKT-UD-FK-87

87" to floorKT-UD-B

Net Price Per Panel

86" 36" $220 $293

86" 48"  $285 $380

86" 60" $355 $473

86" 72" $425 $567

86" 84" $560 $747

86" 96" $630 $840

L W

USA

CAN

Net Price Per Panel