How to build a robot with an arduino and 8051 microcontroller
-
Upload
edgefxkits-solutions -
Category
Education
-
view
225 -
download
0
Transcript of How to build a robot with an arduino and 8051 microcontroller
How To Build a Robot With an Arduino and 8051 Microcontroller
http://www.elprocus.com/
How To Build a Robot With an Arduino and 8051 Microcontroller
Introduction:The main purpose of robot is to decrease the man power. The robots are used in electronics in many applications. In this presentation we are discussing about how to build the obstacle-avoiding robot with the Arduino module & 8051 microcontroller.
http://www.elprocus.com/
How To Build a Robot With an Arduino and 8051 Microcontroller
The required components to build the robot includes the following
How To Build a Robot
• Robot Body
• DC Motor
• Arduino Module
• Motor Driver IC
• Ultrasonic Sensor
http://www.elprocus.com/
How To Build a Robot With an Arduino and 8051 Microcontroller
How to Build a Robot
1. Robot Body
The basic robot body of the robot of obstacle avoidance vehicle.
The robot body is a plastic body and it contains wheels on both sides.
Ultrasonic sensor is arranged in front of the robot body.
By using the ultrasonic sensor the obstacle can be detected.
http://www.elprocus.com/
How To Build a Robot With an Arduino and 8051
MicrocontrollerRobot Body
Any obstacle is detected by the ultrasonic sensor while the robot is moving.
Then the robot will move aside and it will continue moving.
http://www.elprocus.com/
How To Build a Robot With an Arduino and 8051 Microcontroller
2. DC Motor
The DC motor is an electric motor and it runs with direct current.
The operation of any motor is based on the electromagnetism.
The magnetic field is produced by the current carrying conductors
When it is placed in an external magnetic field, it will experience a force proportional to the current in the conductor.
http://www.elprocus.com/
How To Build a Robot With an Arduino and 8051 Microcontroller
DC Motor Generally, we know that the magnets are opposite polarity attraction
from north to south.
If the polarities are same like north to north & south to south then the magnets will repel.
DC Motor
http://www.elprocus.com/
How To Build a Robot With an Arduino and 8051
MicrocontrollerDC Motor
The internal configuration of DC motor is designed to attach the magnetic interaction between the current carrying conductor and the external magnetic field to produce the motion.
Here we are using two DC motors, each motor contains 6v and the total two DC motors contain 12v.
The two DC motors are placed in the robot body
http://www.elprocus.com/
How To Build a Robot With an Arduino and 8051 Microcontroller
DC Motor The robot body is moved with the help of the DC motors
Robot Body with DC Motor
http://www.elprocus.com/
How To Build a Robot With an Arduino and 8051 Microcontroller
3. Arduino Module
The following image shows the arduino module image.
http://www.elprocus.com/
How To Build a Robot With an Arduino and 8051 Microcontroller
3. Arduino Module
The arduino module plays an important role in the design of the obstacle avoidance robot using arduino kit.
The receiver pin of the arduino is connected to the second pin of ultrasonic sensor.
The 1st, 2nd, & 3rd pin of arduino module is connected to the DC motor driver.
The common components capacitor and diode are also connected to the arduino module with the help of the battery power supply.
http://www.elprocus.com/
How To Build a Robot With an Arduino and 8051 Microcontroller
4. Motor Driver IC To run the DC motor the motor driver IC used.
The pins 3,6 & 11, 14 of motor driver are connected to the DC motor.
The input pin 1 and 2 are connected to the arduino module and the enable pin is connected to the transmitter pin of the arduino.
The pins 4, 5, 12, 13 of motor driver are connected to the ground.
http://www.elprocus.com/
How To Build a Robot With an Arduino and 8051 Microcontroller
Ultrasonic Sensor
In this concept the ultrasonic sensor is used to detect an obstacle ahead.
It will send the command to the arduino board.
Depending upon the input signal the microcontroller redirects the robot to move in alternate directions.
http://www.elprocus.com/
How To Build a Robot With an Arduino and 8051 Microcontroller
The applications of the arduino robot obstacle avoidance
Ultrasonic Sensor
• The arduino robot can move on any surface
• It can move on metallic surface like refrigerator body.
http://www.elprocus.com/
How To Build a Robot With an Arduino and 8051 Microcontroller
The below image shows the arduino robot for obstacle avoidance
Arduino Robot for Obstacle Avoidance
http://www.elprocus.com/
How To Build a Robot With an Arduino and 8051 Microcontroller
Building Robot With 8051 Microcontroller
The components required to build the robot with the 8051 microcontroller are
• 8051 microcontroller
• DC motors
• Motor drivers
• Metal detector
To build a robot with the 8051 microcontroller, We took the metal detector robot vehicle for the explanation.
http://www.elprocus.com/
How To Build a Robot With an Arduino and 8051 Microcontroller
• Decoder
• Encoder
• Push buttons
• Crystal
• RF transmitter and receiver
Building Robot With 8051 Microcontroller
http://www.elprocus.com/
How To Build a Robot With an Arduino and 8051 Microcontroller
Metal Detector
The metal detector is a coil it has one or more metal coils used to detect the metals on the ground.
The metal detector works on the principle of the electromagnetic induction.
The metal detector is connected to the robot body through the PCB.
http://www.elprocus.com/
How To Build a Robot With an Arduino and 8051 Microcontroller
Metal Detector The following image shows the general metal detector used in the
electronic projects.
http://www.elprocus.com/
How To Build a Robot With an Arduino and 8051 Microcontroller
Push Buttons The push buttons are buttons which are made up of hard metals like
plastic and metal.
Generally the push buttons are used to reset the program in the microcontroller.
The following image shows the push button image.
http://www.elprocus.com/
How To Build a Robot With an Arduino and 8051 Microcontroller
8051 Microcontroller The 8051 microcontroller consists of 40 pins.
The 4th & 5th pin of the microcontroller is connected to the crystal oscillator.
The Vcc pin is given to the power supply of 5V and the ground pin is connected to the ground.
The pins 15, 16, 18, 19 of the microcontroller are connected to the encoder IC of HT12E.
The microcontroller pins 2, 7, 8, 9, are connected to the push buttons.
http://www.elprocus.com/
How To Build a Robot With an Arduino and 8051 Microcontroller
8051 Microcontroller The following image after connecting all the components like resistor,
capacitor, crystal oscillator, 8051 series microcontroller, encoders and etc are on the printed circuit board.
PCB Connections
http://www.elprocus.com/
How To Build a Robot With an Arduino and 8051 Microcontroller
8051 Microcontroller The below image shows the metal detector robot with the 8051 series
microcontroller.
Metal Detector Robot with the 8051 Series Microcontroller
http://www.elprocus.com/
How To Build a Robot With an Arduino and 8051 Microcontroller
Here in this project we showed how to build a simple robotic obstacle avoidance using arduino and 8051 Microcontroller. With the help of sensors and other components robot can detect the obstacle and turn around and avoid crashing.
Conclusion