How to Assemble an - Over The Edge- Wholesale Aquarium Tank Frames
Transcript of How to Assemble an - Over The Edge- Wholesale Aquarium Tank Frames
![Page 1: How to Assemble an - Over The Edge- Wholesale Aquarium Tank Frames](https://reader035.fdocuments.in/reader035/viewer/2022071600/613d19e5736caf36b759531a/html5/thumbnails/1.jpg)
How to Assemble an Aquarium Strip Light
By Over The Edge and Aquariumframeswholesale.com
![Page 2: How to Assemble an - Over The Edge- Wholesale Aquarium Tank Frames](https://reader035.fdocuments.in/reader035/viewer/2022071600/613d19e5736caf36b759531a/html5/thumbnails/2.jpg)
Parts Needed For Single Bulb Fixture
• Light Shell • Light Insert • Cord With Switch • Electronic Ballast • Two #6-1/2 Screws • Two #10-1/2 Screws • Two Wire Nuts • Two Light Sockets
For Double Bulb Fixtures You will need Two Ballast, Four Light Sockets, and Four Self Tapping Screws, and Four Light Shell Screws
![Page 3: How to Assemble an - Over The Edge- Wholesale Aquarium Tank Frames](https://reader035.fdocuments.in/reader035/viewer/2022071600/613d19e5736caf36b759531a/html5/thumbnails/3.jpg)
Tools Needed
• Wire Strippers/Cutter • Phillips Screw Driver
(Magnetic works Best)
• Razor knife/Box Cutter • Power Driver/Drill • ¼ inch Drill Bit
![Page 4: How to Assemble an - Over The Edge- Wholesale Aquarium Tank Frames](https://reader035.fdocuments.in/reader035/viewer/2022071600/613d19e5736caf36b759531a/html5/thumbnails/4.jpg)
Installing the Light Sockets
![Page 5: How to Assemble an - Over The Edge- Wholesale Aquarium Tank Frames](https://reader035.fdocuments.in/reader035/viewer/2022071600/613d19e5736caf36b759531a/html5/thumbnails/5.jpg)
Installing the Light Sockets
-Use Razor Knife to scrape away enough plastic to make the light sockets click in without breaking the insert
-Scrape a little at a time, checking to make sure that the light socket doesn’t fall out -Repeat for each light socket
![Page 6: How to Assemble an - Over The Edge- Wholesale Aquarium Tank Frames](https://reader035.fdocuments.in/reader035/viewer/2022071600/613d19e5736caf36b759531a/html5/thumbnails/6.jpg)
Installing the Light Sockets -Push Light Socket in one side of the insert at a time, clicking it into place -If the socket doesn’t clip in place, scrape a little more plastic away and try again.
-This procedure may be a little difficult for first time builders
![Page 7: How to Assemble an - Over The Edge- Wholesale Aquarium Tank Frames](https://reader035.fdocuments.in/reader035/viewer/2022071600/613d19e5736caf36b759531a/html5/thumbnails/7.jpg)
Installing the ballast
![Page 8: How to Assemble an - Over The Edge- Wholesale Aquarium Tank Frames](https://reader035.fdocuments.in/reader035/viewer/2022071600/613d19e5736caf36b759531a/html5/thumbnails/8.jpg)
Installing the Ballast
-Lay the Ballast Flat, with the mounting brackets facing up -Set the insert facing upwards
![Page 9: How to Assemble an - Over The Edge- Wholesale Aquarium Tank Frames](https://reader035.fdocuments.in/reader035/viewer/2022071600/613d19e5736caf36b759531a/html5/thumbnails/9.jpg)
Installing the Ballast
-Leaving the first screw loose will make it easier to line up the second screw -Install second screw -Both screws can now be tighten. Do not over tighten screws
-Slide Ballast under the insert, lining up screw holes -Put one #6-1/2 screw in one side of ballast, leaving it loose
![Page 10: How to Assemble an - Over The Edge- Wholesale Aquarium Tank Frames](https://reader035.fdocuments.in/reader035/viewer/2022071600/613d19e5736caf36b759531a/html5/thumbnails/10.jpg)
Wiring the Ballast
![Page 11: How to Assemble an - Over The Edge- Wholesale Aquarium Tank Frames](https://reader035.fdocuments.in/reader035/viewer/2022071600/613d19e5736caf36b759531a/html5/thumbnails/11.jpg)
Wiring the Ballast
-Cut wires making sure to leave a couple inches of extra length -Do this for both the blue and red wires
-Take wires and separate them by color.
![Page 12: How to Assemble an - Over The Edge- Wholesale Aquarium Tank Frames](https://reader035.fdocuments.in/reader035/viewer/2022071600/613d19e5736caf36b759531a/html5/thumbnails/12.jpg)
Wiring the Ballast
-Strip the wires ½ inch from the end
-Do this for both the red and blue wires
![Page 13: How to Assemble an - Over The Edge- Wholesale Aquarium Tank Frames](https://reader035.fdocuments.in/reader035/viewer/2022071600/613d19e5736caf36b759531a/html5/thumbnails/13.jpg)
Wiring the Ballast
-Insert the other red wire into the other hole on the same light socket -Repeat this step for the blue wires
-Insert the red wire into one of the holes in the light socket
![Page 14: How to Assemble an - Over The Edge- Wholesale Aquarium Tank Frames](https://reader035.fdocuments.in/reader035/viewer/2022071600/613d19e5736caf36b759531a/html5/thumbnails/14.jpg)
Wiring the Ballast
-Your Insert is now completed -For a double bulb insert, repeat all previous steps up to this point
![Page 15: How to Assemble an - Over The Edge- Wholesale Aquarium Tank Frames](https://reader035.fdocuments.in/reader035/viewer/2022071600/613d19e5736caf36b759531a/html5/thumbnails/15.jpg)
Preparing the Light Shell
-Drill ¼ inch hole in the center of the back of the shell approximately a ¼ inch from the top of the shell
![Page 16: How to Assemble an - Over The Edge- Wholesale Aquarium Tank Frames](https://reader035.fdocuments.in/reader035/viewer/2022071600/613d19e5736caf36b759531a/html5/thumbnails/16.jpg)
Preparing the Light Shell
-Take cord with switch and push the wire through the hole in the back of the light shell
![Page 17: How to Assemble an - Over The Edge- Wholesale Aquarium Tank Frames](https://reader035.fdocuments.in/reader035/viewer/2022071600/613d19e5736caf36b759531a/html5/thumbnails/17.jpg)
Preparing the Light Shell
-Spread the wires apart and tie a knot in the wire
-This will prevent the wire from pulling back out of the shell
![Page 18: How to Assemble an - Over The Edge- Wholesale Aquarium Tank Frames](https://reader035.fdocuments.in/reader035/viewer/2022071600/613d19e5736caf36b759531a/html5/thumbnails/18.jpg)
Preparing the Light Shell
-Your Light Shell is now prepared for the light insert
![Page 19: How to Assemble an - Over The Edge- Wholesale Aquarium Tank Frames](https://reader035.fdocuments.in/reader035/viewer/2022071600/613d19e5736caf36b759531a/html5/thumbnails/19.jpg)
Installing the Insert into Light Shell
![Page 20: How to Assemble an - Over The Edge- Wholesale Aquarium Tank Frames](https://reader035.fdocuments.in/reader035/viewer/2022071600/613d19e5736caf36b759531a/html5/thumbnails/20.jpg)
Installing the Insert into Light Shell
-You have 2 black wires coming from the cord with switch and 2 wires (Black and White) coming from the ballast
![Page 21: How to Assemble an - Over The Edge- Wholesale Aquarium Tank Frames](https://reader035.fdocuments.in/reader035/viewer/2022071600/613d19e5736caf36b759531a/html5/thumbnails/21.jpg)
Installing the Insert into Light Shell
-Take one wire from the cord and the black wire from the ballast
![Page 22: How to Assemble an - Over The Edge- Wholesale Aquarium Tank Frames](https://reader035.fdocuments.in/reader035/viewer/2022071600/613d19e5736caf36b759531a/html5/thumbnails/22.jpg)
Installing the Insert into Light Shell
-Keep twisting the wire nut until wire looks braided -This will help keep the wires together when installing the insert
-Use Wire nut to tie one wire from cord with switch and black wire from ballast together
![Page 23: How to Assemble an - Over The Edge- Wholesale Aquarium Tank Frames](https://reader035.fdocuments.in/reader035/viewer/2022071600/613d19e5736caf36b759531a/html5/thumbnails/23.jpg)
Installing the Insert into Light Shell
-Repeat last step for the other black wire from the cord with switch to the white wire from ballast
![Page 24: How to Assemble an - Over The Edge- Wholesale Aquarium Tank Frames](https://reader035.fdocuments.in/reader035/viewer/2022071600/613d19e5736caf36b759531a/html5/thumbnails/24.jpg)
Installing Insert into the shell (Optional Step) At this point, it is recommended to test your light fixture to make sure that your light is working properly before installing insert into shell
![Page 25: How to Assemble an - Over The Edge- Wholesale Aquarium Tank Frames](https://reader035.fdocuments.in/reader035/viewer/2022071600/613d19e5736caf36b759531a/html5/thumbnails/25.jpg)
Lining up the Insert
-When installing insert into shell, line up raised pegs in shell to holes in the insert -Make sure when you are installing insert into the shell, that the air vents are towards the back of the shell.
![Page 26: How to Assemble an - Over The Edge- Wholesale Aquarium Tank Frames](https://reader035.fdocuments.in/reader035/viewer/2022071600/613d19e5736caf36b759531a/html5/thumbnails/26.jpg)
Screwing Insert into shell
![Page 27: How to Assemble an - Over The Edge- Wholesale Aquarium Tank Frames](https://reader035.fdocuments.in/reader035/viewer/2022071600/613d19e5736caf36b759531a/html5/thumbnails/27.jpg)
-Do not over tighten the screws or you will break the pegs off in the shell
-Using the Two #10-1/2 screws, make sure the light insert is lined up with the pegs in the shell -Install the 2 screws on the inside holes of the insert
Installing Insert into shell Screwing Insert into shell
![Page 28: How to Assemble an - Over The Edge- Wholesale Aquarium Tank Frames](https://reader035.fdocuments.in/reader035/viewer/2022071600/613d19e5736caf36b759531a/html5/thumbnails/28.jpg)
Congratulations -You have completed building your very own electronic Fluorescent Light Fixture -If you haven’t done so already, You can now test out your light