Hoover Miele Instructions

7/28/2019 Hoover Miele Instructions

1/40

Operating instructions

Vacuum cleaners

To avoid the risk of accidents or damageto the appliance, it is essential to read theseinstructions before using it for the first time.

These operating instructions apply tothe standard S 8000 vacuum cleanersas well as to other models which aredistinguished by names rather than numbers. M.-Nr. 09 246 020

en - GB

HS15


2/40

Caring for our environment

Guide to the appliance

Warning and Safety instructions

Preparing for use

Using the accessories supplied

Use

Mains cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Switching on and off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Adjusting the suction power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

+ / foot controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Foot controls with Automatic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Radio-control handle with Automatic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Opening the air inlet valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Interrupting operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Setting down, transportation and storage

Parking system for pauses in vacuuming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Parking system for storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Maintenance and care

Purchasing new dustbags and filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25Ordering the correct dustbags and filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

When to change the dustbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Replacing the dustbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

When to change the dust compartment filter (for motor protection) . . . . . . . . . . . 28

How to change the dust compartment filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

When to change the exhaust filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Replacing the Air Clean filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Replacing an Active Air Clean filter or an Active HEPA filter . . . . . . . . . . . . . . . . . 31Replacing one type of exhaust filter with another . . . . . . . . . . . . . . . . . . . . . . . . . 32

When to change the battery in the radio-operated handle . . . . . . . . . . . . . . . . . . 33

How to change the battery in the radio-operated handle . . . . . . . . . . . . . . . . . . . 33

When to change the thread lifters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Replacing the thread lifters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Cleaning and care

Problem solving guide / After sales service

Optional accessories

Electrical connection for the UK

Contents

2


3/40

Disposal of packing material

The packaging is designed to protectthe vacuum cleaner from damage

during transportation. The packagingmaterials used are selected frommaterials which are environmentallyfriendly for disposal and should berecycled.

Ensure that any plastic wrappings,bags, etc. are disposed of safely andkept out of the reach of babies and

young children. Danger of suffocation.

Disposing of the dustbag andfilters

These are made from environmentallyfriendly materials. The filters can bedisposed of with the normal householdwaste. The dustbag can also be

disposed of in this way if it has beenused exclusively for general householddust.

Disposing of your oldappliance

Before disposing of your old appliance

remove the dustbag and all the filtersand dispose of them with your normalhousehold waste.

Electrical and electronic appliancesoften contain materials which, ifhandled or disposed of incorrectly,could be potentially hazardous tohuman health and to the environment.

They are, however, essential for thecorrect functioning of your appliance.Please do not therefore dispose of itwith your household waste.

Please dispose of it at your localcommunity waste collection/recyclingcentre, or contact your dealer foradvice.

Ensure that it presents no danger to

children while being stored fordisposal.

Caring for our environment

3


4/40

The illustration shows the maximum number of features available on these Mielevacuum cleaners.


4


5/40

a Suction hose

b Release button for accessories compartment

c Dustbag change indicator

d Display *

e Foot switch for automatic cable rewind

f Parking system for pauses in vacuuming

g On/Off foot control s

h Mains cable

i Roller wheels *

jExhaust filter *

k Parking attachment (on both sides of the vacuum cleaner)

l Dust compartment filter (for motor protection)

m Electrobrush socket cover holder

n Original Miele dustbag

o Carrying handle

p Floorhead *

q Release button

r Telescopic or triscopic tube *

s Dust compartment release button

t Release buttons for the telescopic or triscopic tube *

u Socket for Electrobrush *

v Connection socket

w LED *

x Stand-by button for pauses in vacuuming *

y Suction power selector + /- *

z Handle (some models have an air inlet valve in the handle) *

{ Overheating warning light *

| Restart button *

} Stand-by indicator light *

~ Exhaust filter change indicator and re-set button *

Those features marked * depend on model, and may vary or not be available onyour model.


5


6/40

This vacuum cleaner meets statutory safety requirements.

Improper use can, however, lead to personal injury and damage

to property.

To avoid the risk of accidents and damage to the vacuum

cleaner, please read these instructions carefully before using it

for the first time. They contain important information on its safety,

operation and maintenance.

Keep these instructions in a safe place and ensure new users arefamiliar with the content. Pass them on to any future owner.

Always disconnect the vacuum cleaner from the mains supply

when you have finished using it, before changing over

accessories, as well as for maintenance work and cleaning.

Switch it off at the wall socket and unplug it.

Correct application

~This vacuum cleaner is not designed for commercial use. It isintended for use in domestic households and for use in similar

working and residential environments.

~The vacuum cleaner is not intended for outdoor use.

~The vacuum cleaner must only be used for domestic householdpurposes to vacuum dry floor surfaces. Do not use on people or

animals. Any other usage, modification or alteration is not supported

by the manufacturer and could be dangerous.

~This appliance can only be used by people with reducedphysical, sensory or mental capabilities, or lack of experience or

knowledge, if they are supervised whilst using it, or have been

shown how to use it correctly by a person responsible for their

safety.


6


7/40

Safety with children

~This vacuum cleaner is not a toy! To prevent the risk of injury, do

not let children play with the appliance or its controls.

~Children 8 years and older may use, clean or maintain the vacuumcleaner without adult supervision only if they have been shown how to

do so in a safe way and understand the hazards involved.

~Children under 8 years of age must be kept away from theappliance unless they are constantly supervised.

~Models with radio controls on the handle: Keep batteries out ofthe reach of children.

Technical safety

~Ensure that the connection data on the data plate (voltage andfrequency) match the mains electricity supply exactly.

~Before using the vacuum cleaner, check for any visible signs ofdamage. Do not use a damaged appliance.

~The plug must be fitted with a 13 A fuse (UK).

~While the vacuum cleaner is under guarantee, repairs should onlybe undertaken by a service technician authorised by Miele.

Otherwise the guarantee will be invalidated.

~Do not pull or carry the appliance by the cable, and be carefulnot to damage the cable when withdrawing the plug from the socket.

Keep the cable away from sharp edges and do not let it get

squashed, for example, under a door.

Avoid running the vacuum cleaner over the cable. This could

damage the cable, plug or socket.

The appliance must not be used is any of these have suffereddamage.


7


8/40

~Do not use the vacuum cleaner if the cable is damaged. If thecable is damaged it must be replaced together with a complete

cable rewind. For safety reasons this work must be done by the

Miele Service Department or a Miele authorised service technician.

~The socket on the vacuum cleaner (depending on model) must onlybe used for the Miele Electrobrush specified for use with this appliance.

~When vacuuming especially fine dust, e.g. sawdust, sand,plaster, flour, talcum powder etc., electrostatic charges build up

naturally. Under certain conditions these charges will be released.

To avoid the unpleasant effects of these discharges, a metal inlayhas been incorporated into the underside of the handle. Please

make sure that you keep your hand in constant contact with this

metal strip during vacuuming.

~Do not let the vacuum cleaner get wet. Clean only with a dry clothor slightly damp cloth when disconnected from the mains supply.

~Repairs should only be carried out by a Miele authorised servicetechnician. Repairs and other work by unqualified persons could be

dangerous. The manufacturer cannot be held liable for unauthorised

work.

Correct use

~Floor attachments, accessories and tubes must not be used athead level to avoid the risk of injury, e.g. to eyes and ears.

~To avoid the risk of damage, do not use the vacuum cleaner withoutthe dustbag, dust compartment filter and exhaust filter in place.

~ If the dustbag is not fitted correctly, the dust compartment coverdoes not normally close. Do not force it.

~Do not vacuum up anything which has been burning or is stillglowing e.g. cigarettes, ashes or coal, whether glowing orapparently extinguished.


8


9/40

~Do not vacuum up any water, liquid or damp dirt. Wait until anyfreshly cleaned or shampooed carpets or floor coverings are

completely dry before attempting to vacuum.

~Do not vacuum toner dust. Toner, such as that used in printersand photocopiers, can conduct electricity.

~Do not vacuum up any inflammable or combustible matter or gasesand do not vacuum in areas where such substances are stored.

~ Important information on the handling of batteries (for models with

radio controls on the handle): Do not short circuit or recharge batteries, or throw them into a fire.

Disposing of batteries: Remove the batteries from the radio control

handle and dispose of them in your recycling bin. Do not dispose

of them with the normal household waste.

Accessories

~To avoid the risk of injury when vacuuming with a MieleElectrobrush or Turbobrush, do not touch the rotating roller brush.

~The Miele Electrobrush is a motor driven accessory for use onlywith Miele vacuum cleaners. The vacuum cleaner must not be used

with an electrobrush produced by another manufacturer.

~ It is not advisable to vacuum directly with the handle, i.e. withoutan accessory attached, as the rim could get damaged and youcould hurt yourself on sharp edges.

~Only use genuine dustbags, filters, accessories and optionalaccessories with the "Original Miele" logo on them. This will ensure

optimum performance of the appliance throughout its life.

The manufacturer cannot be held liable for damage caused byincorrect use or operation or by non-compliance with these

Warning and Safety instructions.


9


10/40

Attaching the suction hose

^ Insert the hose connector into thesocket until it clicks into position. To

do this, line up the guides on the twopieces.

Removing the suction hosefrom the cleaner

^ Press the release buttons at the sideof the hose connector, and lift thehose from the socket.

Connecting the handle to the

suction hose

^ Insert the suction hose into thehandle until it clicks into position.

Preparing for use

10


11/40

Connecting the handle to thesuction tube

^ Insert the handle into the suction tube

until it clicks into position. To do this,line up the guides on the two pieces.

^ To release the handle from the suctiontube, press the release button andpull the handle away from the tube.

Your vacuum cleaner is fitted with oneof the following telescopic tubes,depending on the model:

Telescopic tube Triscopic tube

Adjusting the telescopicsuction tube

One part of the telescopic tube ispacked inside the other and can beadjusted to suit your height for

comfortable vacuum cleaning.

^ Press the telescopic tube releasebutton to release the tubes andadjust to the required height.

Adjusting the triscopic suctiontube

The triscopic tube has three sections.Two sections are packed togetherinside a third outer tube.

^ Press the release button (see arrowa) to release the lower tube and pullit right out until it clicks. Press thebutton again when you want to retractthe tube. The tube will click into place.

^ Press button b and pull theadjustable tube out to the requiredheight.

Preparing for use

11


12/40

Fitting the standard floorhead

^ Push the suction tube into thefloorhead and turn it clockwise or

anti-clockwise until it clicks intoposition.

^ To release the floorhead from thesuction tube, press the releasebutton (see arrow) and pull thesuction tube away from the floorhead.

The floorhead can be used for allnormal cleaning of carpets and rugs. It

can also be used with the brushprotruding to vacuum hard flooring. Forhard flooring, such as stone andparquet, we recommend using one ofthe special Miele floor brushes (see"Optional accessories").

Preparing for use

12


13/40

Adjusting the standardfloorhead

Please observe the flooringmanufacturer's cleaning and care

instructions.

Vacuum carpets and rugs with thebrush retracted:^ Press the foot control%.

Clean hard flooring which is notsusceptible to scratching with the brush

protruding:^ Press the foot control).

Clean flooring which has deep

crevices or grooves with the brush

protruding.

AirTeQ floorhead

This floorhead has been speciallydeveloped to achieve excellentcleaning results using low energy. Ithas particularly low power consumptionand high suction capability.

Warning: If the suction power of the

AirTeQ floorhead seems too high,

reduce the suction until the

floorhead is easier to manouevre

(see "Correct use - adjusting thesuction power").

Preparing for use

13


14/40

a Crevice nozzle

For cleaning in folds, crevices orcorners.

b Natural bristle dusting brushFor dusting shelves, ornate or carveditems or delicate objects. The head ofthe dusting brush can be swivelled toattain the best cleaning position.

c Upholstery nozzle

For cleaning upholstery, mattresses,cushions, curtains, covers etc.

Certain models are supplied asstandard with the following accessorieswhich are not illustrated on this page.

Electrobrush Turbobrush Classic Allergotec floorhead

These floorheads and brushes aresupplied with their own operatinginstructions.

To open the accessoriescompartment

^ Press the release button to open theaccessories compartment lid.

^ Take out the accessory you require.

^Press down firmly on the lid to close it.

Floorhead

For general use and also for vacuumingstairs.

Warning: For safety reasons when

vacuuming stairs it is best to start at

the bottom of the stairs and move

upwards.

Using the accessories supplied

14


15/40

Mains cable

Unwinding the cable

^ Pull the mains cable out to therequired length (max. approx. 7.5 m).

^ Insert the plug in the socket correctly.

Warning: If vacuuming for longer

than 30 minutes, the mains cable

must be pulled out to its fullest

extent. Otherwise there is a danger

of overheating and damage.

Rewinding the cable

^ Switch off at the wall socket andunplug it.

^ Press the rewind foot control briefly.The cable will rewind automatically.

Switching on and off

^ Press the On/Off foot control s.

Use

15


16/40

Adjusting the suction power

The suction power can be regulated tosuit the type of flooring being cleaned.

Reducing the suction power reducesthe amount of effort required tomanoeuvre the floorhead.

Some models also have symbols on thecontrols. The symbols indicate the typeof use the settings are suitable for:

#- curtains, lightweight fabrics

$- upholstery, cushions%- thick pile carpets, rugs and

runners

*- for energy-saving vacuuming (thissetting is also very quiet)

(- loop-pile carpets

)- heavily soiled hard flooring and for

intensive cleaning of carpets

When using the AirTeQ floorhead, if

the suction seems too high, reduce

the suction until the floorhead iseasier to manouevre.

Use

16


17/40

Depending on the model, your vacuumcleaner will be fitted as standard withone of the following suction powerselectors:

+ / foot controls

The first time the vacuum cleaner isswitched on, the highest power settingwill be selected automatically.After that, the vacuum cleaner willswitch on at the setting which was usedpreviously.

^ Press the + control to select a highersetting.

^ Press the - control to select a lowersetting.

Foot controls with Automatic

The first time the vacuum cleaner is

switched on, the "Auto" power settingwill be selected automatically.

Auto = suction power is automaticallyadjusted for the type of floorbeing vacuumed

Do not use the "Auto" setting to

vacuum lightweight materials or

curtains. These could be sucked in

and possibly damaged.

^ Press the + control to select a highersetting.

^ Press the - control to select a lowersetting.

After that, the vacuum cleaner willswitch on at the setting which was usedpreviously.

Use

17


18/40

Radio-control handle with Automatic

When the vacuum cleaner is switchedon with the On/Off foot control s, the

Stand-by indicator on the vacuumcleaner - will light up yellow.

^ Press the Stand-by button - on thehandle.

The Stand-by indicator - on thevacuum cleaner will go out.

The first time the vacuum cleaner isswitched on, the highest power settingwill be selected automatically.

After that, the vacuum cleaner willswitch on at the setting which was usedpreviously.

^ Press the + button to select a highersuction power level.

^ Press the - button to select a lowersuction power level.

Auto = suction power is automaticallyadjusted for the type of floorbeing vacuumed

Do not use the "Auto" setting to

vacuum lightweight materials or

curtains. These could be sucked in

and possibly damaged.

Use

18


19/40

Opening the air inlet valve

(not on models with radio-controls onthe handle)

It is easy to reduce the suction powerfor a short time, e.g. to prevent rugs orother objects being sucked into thevacuum cleaner.

^ Open the air inlet valve far enough toreduce the suction power.

The floorhead will be easier to

manoeuvre. Close the valve when youare ready to use full power again.

Use

19


20/40

Vacuuming

^ When vacuuming, pull the cleanerbehind you on its wheels. You can

stand it upright for vacuuming stairsand curtains etc.

Warning: When vacuuming

especially fine dust, e.g. sawdust,

sand, plaster, flour, talcum powder

etc., electrostatic charges build up

naturally. Under certain conditions

these charges will be released. To

avoid the unpleasant effects of thesedischarges, a metal inlay has been

incorporated into the underside of

the handle. Please make sure that

you keep your hand in constant

contact with this metal strip during

vacuuming.

Use

20


21/40

Interrupting operation

(models with radio controls on thehandle)

To pause the vacuum cleaner duringoperation:

^ Press the Stand-by button - on thehandle.

Warning: The Stand-by button isdesigned to pause the vacuum

cleaner for short periods of time

whilst vacuuming. After vacuuming,the vacuum cleaner must be

switched off and unplugged from

the mains electricity supply.

Otherwise there is a danger ofoverheating and damage.

At the end of the pause, you can doone of the following:

^ Press the Stand-by button - again toswitch the vacuum cleaner back onat the setting you were using beforepausing it.

^ Press the + button to switch thevacuum cleaner back on using thehighest power setting.

^ Press the - button to switch thevacuum cleaner back on using thelowest power setting.

Use

21


22/40

Parking system for pauses invacuuming

(cannot be used with the SEB 234 L

Electro Premium Electrobrush)

A parking system has been designedfor conveniently parking the suctiontube and floorhead during pauses.

^ Slot the floorhead into the parkingattachment at the back of thevacuum cleaner.

If the vacuum cleaner is on a slopingsurface, e.g. a ramp, retract the

suction tube fully.

Switching on and off with the parking

system

Some models are fitted with an On / Offswitch in the parking system. Operation

of the vacuum cleaner is automaticallyinterrupted, if you stow the floorhead inthe parking system.When the floorhead is removed fromthe parking system, the vacuumcleaner switches on again at the lastselected power level (not models withradio-control handle).


22


23/40

Parking system for storage

Always disconnect the vacuum

cleaner from the electrical supplywhen you have finished using it.

Switch off at the wall socket and

unplug it.

^ Stand the vacuum cleaner uprightwhen it is not being used and when itis being stored.

Retract the telescopic tube fully.

^ Slot the floorhead downwards intoone of the parking attachments oneither side of the vacuum cleaner(the parking attachments cannot beused with the SEB 234 L Electro Pre-mium Electrobrush).

This makes the cleaner easier to carry

or store.


23


24/40

If your vacuum cleaner has an XXLhandle, you can detach this so that thevacuum cleaner requires less storagespace.

^ Detach the XXL handle from theretracted suction tube.

^ Wind the suction hose around thesuction tube and then slot the XXLhandle into the second parkingattachment.


24


25/40

Warning: Always disconnect the

vacuum cleaner from the electrical

supply for maintenance work and for

cleaning. Switch off at the wallsocket and unplug it.

The Miele filtration system consists ofthree filters which must be replacedfrom time to time to ensure that yourvacuum cleaner performs efficiently.

Dustbag

Dust compartment filter (for motorprotection)

Exhaust filter

Only use genuine dustbags, filters,

accessories and optional

accessories with the "Original Miele"

logo on them. Only this will ensure

that the suction power of thevacuum cleaner is maintained,

giving the best possible cleaningresults.

Warning: The use of dustbags made

from paper or paper-based

materials, or dustbags with a

cardboard collar, or dustbags thatdo not carry the "Original Miele"

logo, can seriously damage thevacuum cleaner and invalidate the

warranty.

Purchasing new dustbags andfilters

Original Miele dustbags and filters can

be ordered from your Miele Dealer,from Miele or online at:

Ordering the correct dustbagsand filters

Only use original Miele G/N dustbagswith a blue collar. Using any otherdustbags will damage the vacuumcleaner. Original Miele dustbags areidentified by the "Original Miele" logo onthe packaging or directly on thedustbag.

An Air Clean filter and a dustcompartment filter are supplied withevery packet of Miele dustbags.These can also be purchasedseparately.

You can replace the exhaust filter fittedin the vacuum cleaner with one of theother Miele exhaust filters if you wish(see "Optional accessories").


25


26/40

When to change the dustbag

Change the dustbag when the colourmarker in the dustbag change indicator

fills the display, or sooner if it is nolonger effective (see possible reasonsfor this below).

Miele dustbags are disposable and

designed to be used only once.

Dispose of the dustbag when it is

full. Do not attempt to reuse them assuction would be reduced.

Checking the dustbag change

indicator

^ Attach the standard floorhead to thesuction tube. Do not use any of theother floorheads or attachments asthey will cause the dustbag changeindicator to give a false reading.

^ Switch the vacuum cleaner on andselect the maximum power setting.

^ Lift the floorhead off the floor a little. Ifthe marker completely fills thedustbag change indicator, youshould replace the dustbag with anew one.

How the dustbag change indicator

works

The dustbag change indicator is set fornormal household dust. This generallycontains a mixture of dust, hair, carpetfluff, threads, grit etc.

However, if the cleaner has been usedto vacuum up fine dust, such asplaster, brick dust, cement or flour, thepores of the dustbag will becomeblocked very quickly. This affects theair permeability of the bag, and themarker will indicate that the bag is "full"even when it is not. If this happens youmust still change the dustbag because

suction power will be greatly reducedby blocked pores in the dustbag.

If, on the other hand, you havevacuumed up a large amount of hairand carpet fluff which typically containsa lot of air, the indicator may fail toreact even though the bag is full. Youshould still change it! Both these

extremes can occur.


26


27/40

Replacing the dustbag

^ Press the release button for the dustcompartment lid and raise the lid as

far as it will go.

The dustbag has a closing flap whichcloses automatically when the dustcompartment lid is raised to preventany dust escaping.

^ Pull the dustbag out by the grip nextto the self-closing flap on the collar.

^ Fit the new dustbag into the blue

holder as far as it will go. Leave itfolded up when you take it out of thebox.

^ It should be unfolded in the dustcompartment.

^ Close the dust compartment lidsecurely, making sure it clicks intoposition. Take care not to trap thedustbag when doing so.

Warning: The lid will not close

without a dustbag in place. Do notuse force!


27


28/40

When to change the dustcompartment filter (for motorprotection)

Replace this filter every time you start anew packet of dustbags. A dustcompartment filter is supplied withevery packet of Miele dustbags.

How to change the dustcompartment filter

^ Open the dust compartment lid.

^ Pull the dustbag out by the grip nextto the self-closing flap on the collar.

^ Lift up the blue filter frame until itclicks and remove the old filter. Holdby the clean, unsoiled section toremove it.

^ Replace with a new dust

compartment filter.

^ Close the filter frame.

^ Fit the dustbag into the holder as faras it will go.

^ Close the dust compartment lidsecurely, making sure it clicks intoposition. Take care not to trap the

dustbag when doing so.


28


29/40

When to change the exhaustfilter

Depending on model, your vacuum

cleaner will be fitted as standard withone of the following exhaust filters:

a Air Clean

Replace this filter every time you start anew packet of Miele dustbags. An AirClean exhaust filter and a dustcompartment filter are supplied withevery packet of Miele dustbags.

b Active Air Clean SF-AAC 50 (black)

c Active HEPA SF-AH 50 (blue)

Change these filter types approx. oncea year.Make a note of the date on the filter.

Exhaust filter change indicator

Certain models are fitted with anexhaust filter change indicator to showyou when to change your Active AirClean b or Active HEPA c filter.

The indicator lights up after approx. 50hours of operation, which is equivalentto about a year of average use. Thevacuum cleaner can still be used withthe exhaust filter indicator lit up.However, the suction power will bereduced as will the effectiveness of thefilter if it is not replaced in good time.

The filter change indicator light isirrelevant if an Air Clean filter a is fitted,

as long as it is replaced every time anew packet of Miele dustbags isstarted. The indicator light will go outwhen the reset button is pressed.


29


30/40

Replacing the Air Clean filter

Do not use more than one exhaust

filter at a time.


^ Press the release catch on the filtergrille and open the grille until it clicks.

^ Hold the used Air Clean filter by oneof the clean, unsoiled sections.

^ Replace it with a new Air Clean filter.

If you wish to replace the Air Clean

filter with an Active Air Clean filter or

with an Active HEPA filter, see"Replacing one type of exhaust filter

with another".

^ Close the filter grille.

^ Close the dust compartment lidfirmly. It should click into place.


30


31/40

Replacing an Active Air Cleanfilter or an Active HEPA filter

Do not use more than one exhaustfilter at a time.


^ Raise the filter and remove it.

^ Replace it with a new Active AirClean filter or a new Active HEPAfilter and press it down into place.

If you wish to use an Air Clean filter,

see "Replacing one type of exhaust

filter with another".

^ Close the dust compartment lidfirmly. It should click into place.

Resetting the exhaust filter changeindicator

If your vacuum cleaner is fitted with anexhaust filter change indicator, thisneeds to be re-set each time the filter is

replaced. To do this the vacuumcleaner must be switched on.

^ Press the reset button.

The exhaust filter change indicator willgo out and reset to zero.

The filter change indicator can onlybe reset by pressing the reset

button after the light has come on.Pressing the button at any other time

will have no effect.


31


32/40

Replacing one type of exhaustfilter with another

Depending on model, your vacuum

cleaner will be fitted as standard withone of the following exhaust filters:

a Air Clean

b Active Air Clean SF-AAC 50 (black)

c Active HEPA SF-AH 50 (blue)

Please note

1. If you wish to replace the Air Cleanfilter a with an Active Air Clean filter b oran Active HEPA filter c, it is essentialthat you remove the filter grille beforefitting the new type of filter.

2. If you wish to replace the Active AirClean filter b or the Active HEPA filter c

with an Air Clean filter a, then it is

essential that you also fit the filter grille *.

* Filter grille - see "Optionalaccessories".

Do not use more than one exhaustfilter at a time.

The exhaust filter indicator light (withreset button) that is fitted on certain

models is designed to come on

when the Active Air Clean or Active

HEPA filter needs to be changed.

The filter change indicator light isirrelevant if an Air Clean filter is

being used, as long as it is replaced

every time a new packet of Miele

dustbags is started. The indicatorlight will go out when the reset

button is pressed.


32


33/40

When to change the battery inthe radio-operated handle

Approx. every 18 months. One 3 V

battery (CR 2032) is required.

How to change the battery inthe radio-operated handle

^ Open the cover to the batterycompartment using a screwdriver.

^ Replace with a new battery, makingsure the polarity is correct.

^ Replace the cover.

^ Dispose of the old batteryresponsibly.

The vacuum cleaner can still be

used when the battery has run out or

if there is no battery fitted.

^ Switch the vacuum cleaner on usingthe On/Off foot control s. TheStand-by indicator - on the vacuumcleaner will light up yellow.

^ Press the restart button on thevacuum cleaner.

The vacuum cleaner can continue to be

used, but only at maximum power.Cleaning the roller on the floorhead

(Not necessary for the AirTeQfloorhead)

a Release the bearing (with bayonetfitting) using a coin.

b Press the bearing out, and remove it.

c Take out the roller.

^ Remove any threads and hair,replace the roller and refit thebearing.


33


34/40

When to change the threadlifters

The thread lifters on the suction inlet of

the floorhead can be replaced.Check them from time to time andreplace them if the pile has worn down.

Replacing the thread lifters

^ Use a suitable screwdriver to removethe thread lifters from the slots. Thereare two grooves to help you.

^ Fit new thread lifters.

AirTeQ floorhead

^ Use a suitable screwdriver to removethe thread lifters from the slots.

^ Fit new thread lifters.

Upholstery nozzle SPD 10

a Disengage the thread lifter unit ateach side of the upholstery nozzleusing a coin.

b Fit a new thread lifter unit and lockinto position.

Replacement parts are available from

your Miele dealer or from Miele (seeback cover for contact details).


34


35/40

Always disconnect the vacuum

cleaner from the electrical supply

before cleaning it. Switch off at the

wall socket and unplug it.

Vacuum cleaner and accessories

External surfaces of the vacuumcleaner and of the accessories can becleaned with a dry or a slightly dampcloth, or with a proprietary cleanersuitable for plastic.

Do not use abrasive cleaning

agents, glass cleaning agents,

all-purpose cleaners or oil-based

conditioning agents.

Dust compartment

The dust compartment can, if

necessary, be cleaned using a dryduster, brush or, if available, a secondvacuum cleaner to vacuum the dustout.

Warning: Do not let the vacuum

cleaner get wet. If moisture gets into

the appliance, there is a risk of

electric shock.

Cleaning and care

35


36/40

The vacuum cleaner switches off

automatically.

On certain models, the overheating

warning light also comes on.

A temperature limiter switches thevacuum cleaner off automatically if itgets too hot. Some models also have awarning light which comes on toindicate that it has overheated.

This can occur if, for instance, largearticles block the suction tube or whenthe filter bag is full or contains particlesof fine dust. A heavily soiled exhaust ordust compartment filter can also be thecause of overheating. Switch thevacuum cleaner off immediately usingthe On/Off foot control s. Disconnectfrom the electricity supply. Switch it offat the wall socket and unplug it.

After removing the cause, wait for

approx. 20 - 30 minutes to allow thevacuum cleaner to cool down. It canthen be switched on again.

After sales service

In the event of a fault that you cannoteasily remedy, please contact

your Miele Dealer

or

Miele (see back cover for contactdetails).

Please note that telephone calls may

be monitored and recorded for

training purposes (UK only).

Problem solving guide / After sales service

36


37/40

Please observe the flooring

manufacturer's cleaning and care

instructions.

A number of additional accessories andfloorheads are available to order foryour vacuum cleaner via your MieleDealer, Miele or online at:

Certain models are supplied asstandard with one or more of thefollowing accessories:

Electrobrushes

Electrobrushes can only be used onmodels fitted with an electrobrush socket.

Electrobrush Electro Comfort

(SEB 216-3)

This Electrobrush is particularly suitablefor intensive vacuuming of carpetswhich are subject to hard wear. It is veryeffective at removing deep seated dirtand preventing areas of frequent usebeing trodden into a path.

Electrobrush Electro Premium(SEB 234 L)

This Electrobrush is 60 mm wider thanthe SEB 216-3, and is more powerful,making it ideal for cleaning larger floorareas.

It has the following additional featurescompared to the SEB 216-3:

adjustable height settings

LEDs to light up the area beingvacuumed

A multi-function indicator light

Floorheads / brushes

Classic Allergotec floorhead

(SBDH 285-3)

This floorhead is suitable for dailyhygienic cleaning of all floor surfaces.The level of cleanliness of the floorshows in a colour "traffic light" displaywhen vacuuming.

Hard floor brush (SBB 235-3)

This brush is designed for use on hardflooring such as tiled or stone floors.

Parquet floor brush (SBB Parquet-3)

This brush has natural bristles and isdesigned for use on parquet floors andother surfaces which are susceptible toscratching such as laminate flooring.

Parquet Twister swivel-action

floorbrush (SBB 300-3)

This brush is suitable for a variety ofhard floor surfaces and has a swiveljoint enabling it to get into awkwardcorners.

Parquet Twister XL swivel-action

floorbrush (SBB 400-3)

This brush is extra wide making itsuitable for large areas of flooring andhas a swivel joint enabling it to get intoawkward corners.


37


38/40

Turbo Comfort Turbobrush

(STB 205-3)

This turbobrush is ideal for cleaning cut

pile carpet.

Other accessories

MicroSet (SMC 20)

This set is specially designed forcleaning small objects and difficult toreach areas (such as PC keyboards,stereo equipment, intricately carved

furniture and ornaments, models etc).

CarCare Set (SCC 10)

For valeting the interior of cars.

Cat&Dog Set (SCD 10)

Especially for households with pets.

HomeCare Set (SHC 10)

Accessories for cleaning the livingareas of your home.

Hand Turbobrush Turbo MiniCompact (STB 20)

For cleaning upholstery, mattresses,

car seats etc.

Universal brush (SUB 20)

For dusting books, shelves, etc.

Radiator brush (SHB 20)

For cleaning radiators, narrow shelvesand crevices.

Mattress nozzle (SMD 10)

For cleaning upholstery, mattresses,cushions, curtains, covers etc.

Crevice nozzle, 300 mm (SFD 10)

Extra-long crevice nozzle for cleaningin folds, crevices or corners.

Crevice nozzle, 560 mm (SFD 20)

Flexible crevice nozzle for accessingawkward to reach areas.

Upholstery nozzle, 190 mm (SPD 10)

For cleaning upholstery, mattresses,car seats etc.

Flexible extension hose (SFS 10)

For extending the suction hose byapprox. 1.5 m.

Hygiene seal with active charcoal

This prevents dust and odoursescaping when the suction hose has

been removed from the cleaner.

Filters

Active Air Clean exhaust filter

(SF-AAC 50)

This filter absorbs odours from the dirtcollected in the dustbag.

Active HEPA filter (SF-AH 50)

Excellent filtration level for the cleanestexhaust air. This filter is particularlysuitable for allergy sufferers.

Filter grille

The filter grille is required if you wish to

fit an Air Clean filter instead of an ActiveAir Clean filter or an Active HEPA filter.


38


39/40

All electrical work should be carried outby a suitably qualified and competentperson in strict accordance with currentnational and local safety regulations

(BS 7671 in the UK).

The voltage and frequency are given onthe data plate located underneath thevacuum cleaner. Please ensure thatthese match the household mainssupply. The fuse rating is quoted on theplug.

The appliance is supplied with a cableand moulded plug ready for connectionto a 230-240 V/50 Hz a.c. single phasesupply.

Non-rewireable plugs BS 1363

The fuse cover must be re-fitted whenchanging the fuse, and if the fuse coveris lost the plug must not be used until a

suitable replacement is obtained. Thecolour of the correct replacement coveris that of the coloured insert in the baseof the plug, or the colour that isembossed in words on the base of theplug, (as applicable to the design ofplug fitted).

Replacement fuses should be ASTA

approved to BS1362 and have thecorrect rating. Replacement fuses andfuse covers may be purchased fromyour local electrical supplier.

Electrical connection for the UK

39


40/40

Alteration rights reserved (S 8310 - S 8790) - 1912 M.-Nr. 09 246 020 / 01

Hoover Miele Instructions

Documents

Transcript of Hoover Miele Instructions