FOR MODELS:HLS01-CGT

PATI

O H

EATE

RO

WN

ER’S

MA

NU

AL

IMPORTANTRead this manual carefully before

assembling, using or servicing this

heater. Keep this manual for future

reference.RR

HLS01-CGT

Batch #

AZ Patio Heater Toll Free Number

888-775-1330

1

Contents

General Safety Information....................................... 1

snoitcurtsnIylbmessA

Components & Hardware........................................ 3&4

Additional Requirements........................................ 4

ssecorPnoitallatsnI

Step1 - Attach Wheel Assembly to Base................. 4

Step 2 – Attach Bucket to Base.............................. 4

Step 3–Attach Cylinder Housing to Base.............. . 5

Step4–Attach Post to Cylinder Housing............... 5

Step 5 – Tabletop Installation.................... ............. 5

Step 6 – Attach Reflector Studs to Screen Cover... 5

Step 7 – Attach Head Assembly to Post.................. 6

Step 8 – Install Reflector.........................................

Warranty ................................................................

6

Step 9 – Attach Reflector Assembly to Studs.......... 7

Step10–Connect Hose & Regulator to Cylinder.... 7

Leak Check............................................................. 9

Operation................................................................ 9

01tsilkcehCnoitarepO

Troubleshooting...................................................... 11

12

Maintenance........................................................... 11

Storage.................................................................... 12

Service.................................................................... 12

General Safety InformationThis manual contains important information about the

assembly, operation and maintenance of this patio heater.

General safety information is presented in these first few

pages and is also located throughout the manual.

Keep this manual for future reference and to educate

new users of this product. This manual should be read in

conjunction with the labeling on the product.

Safety precautions are essential when any mechanical

or propane fueled equipment is involved. These

precautions are necessary when using, storing, and

servicing. Using this equipment with the respect and

caution demanded will reduce the possibilities of personal

injury or property damage.

The following symbols shown below are used extensively

throughout this manual. Always heed these precautions,

as they are essential when using any mechanical or

fueled equipment.

DANGERDANGER indicates an imminently hazardous situation

which, if not avoided, will result in death or serious injury.

WARNINGWARNING indicates an imminently hazardous situation

which, if not avoided, could result in death or serious injury.

CAUTIONCAUTION indicates an imminently hazardous situation

which, if not avoided, may result in minor or moderate

personal injury, or property damage.

FOR YOUR SAFETYDo not store or use gasoline or other

flammable vapor and liquids in the vicinity ofthis or any other appliance.

WARNING: For Outdoor Use Only

WARNINGImproper installation, adjustment, alteration,

service or maintenance can cause injury orproperty damage. Read the instructionsthoroughly before installing or servicing thisequipment.

DANGERFailure to comply with the precautions and instructions

provided with this heater can result in death, serious bodily

injury and property loss or damage from hazards of fire,

explosion, burn, asphyxiation, and/or carbon monoxide

poisoning.

Only persons who can understand and follow the

instructions should use or service this heater.

2

DANGER

• EXPLOSION - FIRE HAZARD• Keep solid combustibles, such as building materials,

paper or cardboard, a safe distance away from the heater

as recommended by the instructions.

• Provide adequate clearances around air openings into

the combustion chamber.

• Never use the heater in spaces which do or may contain

volatile or airborne combustibles, or products such as

gasoline, solvents, paint thinner, dust particles or unknown

chemicals.

• During operation, this product can be a source of

ignition. Keep heater area clear and free from combustible

materials, gasoline, paint thinner, cleaning solvents and

other flammable vapors and liquids. Do not use heater in

areas with high dust content. Minimum heater clearances

from combustible materials: three (3) feet from the sides &

two (2) feet from the top.

FOR YOUR SAFETYIf you smell gas:1. Shut off gas to the appliance.2. Extinguish open flame.3. If odor continues, immediately call your gas

supplier.

WARNINGWe cannot foresee every use which may be made of our

heaters.

Check with your local fire safety authority if you have

questions about heater use.

Other standards govern the use of fuel gases and heat

producing products for specific uses. Your local authorities

can advise you about these.

If no local codes exist, follow National Fuel Gas Code,

ANSI Z223.1. In Canada, installation must conform to local

codes. If no local codes exist, follow the current National

standards of CANADA CAN/CGA-B 149.2.

DANGER

• CARBON MONOXIDE HAZARD• This heater is a combustion appliance. All combustion

appliances produce carbon monoxide (CO) during the

combustion process. This product is designed to produce

extremely minute, non-hazardous amounts of CO if used

and maintained in accordance with all warnings and

instructions. Do not block air flow into or out of the heater.

• Carbon Monoxide (CO) poisoning produces flu-like

symptoms, watery eyes, headaches, dizziness, fatigue and

possibly death. You can't see it and you can't smell it. It's

an invisible killer. If these symptoms are present during

operation of this product get fresh air immediately!

• For outdoor use only .

• Never use inside house, or other unventilated or

enclosed areas.

• This heater consumes air (oxygen). Do not use in

unventilated or enclosed areas to avoid endangering

your life.

CAUTION• SERVICE SAFETY

• Keep all connections and fittings clean. Make sure

propane cylinder valve outlet is clean.

• Inspect hose before use. Replace if there is evidence of

abrasion or wear.

• During set up, check all connections and fittings for leaks

using soapy water. Never use a flame.

• Use as a heating appliance only. Never alter in any way or

use with any device.

• Check entire hose at least annually.

WARNING• BURN HAZARD

• Never leave heater unattended when hot or in use.

• Keep out of reach of children.

3

WARNING• This product is fueled by propane gas. Propane gas is

invisible, odorless, and flammable. An odorant is normally

added to help detect leaks and can be described as a

“rotten egg” smell. The odorant can fade over time so

leaking gas is not always detectable by smell alone.

• Propane gas is heavier than air and leaking propane will

sink to the lowest level possible. It can ignite by ignition

sources including matches, lighters, sparks or open flames

of any kind many feet away from the original leak. Use only

propane gas set up for vapor withdrawal.

• Propane gas should be stored or used in compliance with

local ordinances and codes or with ANSI/NFPA 58. Turn off

propane when not in use.

DANGER

• EXPLOSION - FIRE HAZARD• Never store propane near high heat, open flames, pilot

lights, direct sunlight, other ignition sources or where

temperatures exceed 120 degrees F (49°C).

• Propane vapors are heavier than air and canaccumulate

in low places. If you smell gas, leave the area immediately.

• Never install or remove propane cylinder while heater is

lighted, near flame, pilot lights, other ignition sources or

while heater is hot to touch.

• This heater is red hot during use and can ignite

flammables too close to the burner. Keep flammables at

least 3 feet from sides & 2 feet from top. Keep gasoline and

other flammable liquids and vapors well away from heater.

• The propane cylinder must always be stored outdoors in a

well ventilated space. Never store propane cylinder in an

enclosed area (house, garage, etc.). If heater is to be

stored indoors, disconnect the propane cylinder for outdoor

storage.

Assembly Instructions

ComponentsRemove all components from package.

Reflector Panel(3)

Reflector Plate

Reflector Stud(3)

Heater BurnerScreen

Head Assembly

Cylinder Housing

Post

Regulator

Base

Wheel

Gas Hose LessRegulator

Reflector Assembly

4

HardwarePicture Qty Description

Used in

Step(s)

6

4

Small Bolt

2/3

3

8 Small Screws 3

6 Large Flat Washer 9

Large FlatWasher

9 Cap Nut 8

3 Wing Nut 9

3 Reflector Stud 6

1 Wrench 1 / 3 / 4 /7 / 8

Additional RequirementsThe following items are not included, but are necessary for

the proper assembly of your heater. Do NOT attempt to

assemble without proper tools.

Philips screwdriver w/ medium blade.

Adjustable opening wrench.

Leak Detection Solution(Instructions on how to make

solution are included in step )

Note: You must follow all steps to properly assemble

heater.

Installation process

(For models without Wheels , skip to Step 2)

Step 1 – Attach Wheel Assembly to Base. Line up holes in Wheel Bracket with corresponding

finger tighten 2 Large Nuts.. Be sure that the Wheel Assembly is parallel to the

base, and fully tighten bolts

.

Wheel Assembly

(For models without Bucket , skip to Step 3)

Step 2 – Attach Bucket to Base

. Slide 4 Large screws through holes of Base.

9 Small Screw 8

2 Req’d Large Bolts 2 Req’d Large Nuts

4 Req’d Large Screws 4 Req’d Large Nuts

...

WARNINGCalifornia Proposition 65Combustion by products produced when usingthis product contain chemicals known to the stateof California to cause cancer, birth defects, andother reproductive harm.

Assembly time: 0.5 hour

Large Bolt

10 2/4

8 Small Nuts 3

Large Screws 24

Large Nuts 26

holes in base, insert 2 large bolts through holes and

10 Flange Nuts 2/4

Fill bucket with sand.Slide 4 Large nuts through holes under bucket ..and tighten screws with phillips screw driver.

5

.Step 3 – Attach Cylinder Housing to BaseAttach l-shaped brackets to base housing loosely with 4pcsM8 X M10 large bolts and large flat washers.

Put the Plastic nut & Fastening piece through the post in order.Put the Tabletop through the post as show.

Step 4 – Attach Post to Cylinder Housing top

Open the door, put post through the hole on the top ofCylinder Housing.

Attach post to Cylinder Housing using 4pcs small bolts

Step 5 – Tabletop Installation

Through the Fastening piece to the hole on the Tabletop.Holdthe t abletop using a hand and screw the Fastening piece to the Plastic connecting counter-clockwise using the other one. Fasten the Fastening piece.Screw the Plastic nut to the Plastic connecting counter-clockwise. Fasten the Plastic nut. Adjust the height of the Tabletop. Loose the Plastic nut and adjust the Tabletop height of you want. Fasten the Plastic nut.

Put the Plastic connecting through the post as show.

Step 6 – Attach Reflector Studs to Screen Cover. Insert 3 Reflector Studs. Tighten studs securely.

3 Req’d Reflector Studs

Fill Sand

(For models without tabletop, skip to Step 6)

into Flange nuts from inside tank housing.

Attach cylinder to housing to base with 8 small phillips screws and 8 small nuts. Tighten all hardware from this step.

Optional ground fixtures for surface mounting. Not for use in

Mount optional ground fixtures with 6 pcs small boltsand flange nuts into holes on base housing.

conjunction with wheels. (Not available with all models)

6

. Load Head Assembly by inserting hose into post.. Insert Head Assembly into post.. Control knob should be above decal on post.

. Attach Head Assembly to post, and loosely install four

small bolts.

. Tighten bolts securely.

(For models with Entire Reflector , skip to Step 9)Step 8 – Install Reflector

WARNINGRemove protective cover before assemble.

Note: Leave all screws and nuts loose until entire shield is

sections are aligned..Slide two reflector panels together. . Insert one small screw.

. Attach Cap Nut and loosely tighten.

. Place Reflector center plate into middle of reflector panels

.Repeat procedure to complete the assembly of all foursections..Fully tighten all of the screws in the rolled edge.

9 Req’d Small Screws

9 Req’d Cap Nuts

Step 7 – Attach Head Assembly to Post. Unscrew 4 small bolts from head assembly.

from Head Assembly4 Req’d Small Bolts

and follow same procedure above.

put together to ensure proper alignment. Tighten after

7

Step 9 – Attach Reflector Assembly to Studs. Support Heater.. Slide 3 Large Flat Washers over threaded end of

Studs.

. Position Reflector Assembly on 3 studs.. Install large flat washers on studs & securely tighten

wing nuts but do not over-tighten!

Step 10 – Connect Hose & Regulator to Cylinder

Specifications. You must provide

propane gas and

propane cylinder. Use a

standard 20 lb. propane

cylinderonly.( 5 gal.). Use this heater only

with a propane vapor

withdrawal supply

system. See Chapter 5

of the Standard for

Storage and Handling

of Liquefied Petroleum

Gas, ANSI/NFPA 58.

Your local library or

fire department should have this book.

. The pressure regulator and hose assembly supplied

with the appliance must be used.. The installation must conform with local codes, or in

the absence of local codes, with National Fuel Gas

Code, ANSI Z223.1.. A dented, rusted or damaged propane cylinder may

be hazardous and should be checked by your cylinder

supplier. Never use a propane cylinder with a

damaged valve connection.. The propane cylinder must be constructed and

marked in accordance with the specifications for LP

gas cylinders of the U.S. Department of

Transportation (DOT).. Never connect an unregulated propane cylinder to the

heater.. Screw regulator onto gas hose. Do not cross-thread.

Tighten securely with wrenches.

Attach regulator to cylinder.

Complete attachment.

Install cylinder.

Standard 20 lb. tank

6 Req’d Large Flat Washers 3 Req’d Wing Nuts

The minimum permissible gas supply pressure of 10 W.C. is required for purpose of input adjustment.

The minimum hourly of 17000 Btu is required input rating for a heater for automatic operation at ratings less than full input rating.

8

Leak Check

WARNING• Perform all leak tests outdoors.

• Extinguish all open flames.

• NEVER leak test when smoking.

• Do not use the heater until all connections have been leak

tested and do not leak.

Hose / Regulator

Connection

Regulator / Cylinder

Connection. Make 2-3 oz. of leak check solution (one part liquid

dishwashing detergent and three parts water).. Apply several drops of solution where hose attaches

to regulator.. Apply several drops of solution where regulator

connects to Cylinder.. Make sure all Patio Heater & Light valves are OFF.. Turn Cylinder Valve ON.

If bubbles appear at any connection, there is a leak.. Turn Cylinder Valve OFF.. If leak is at Hose/Regulator connection: tighten

connection and perform another leak test.. If leak is at Regulator/Cylinder Valve connection:

disconnect, reconnect, and perform another leak

check. If you continue to see bubbles after several

attempts, cylinder valve is defective and should be

returned to cylinder’s place of purchase.

If NO bubbles appear at any connection, the

connections are secure.. Turn Cylinder Valve OFF.

NOTE: Whenever gas connections are loosened or

removed, you must perform a complete leak test.. Complete installation.

Operation

DANGER

• CARBON MONOXIDE HAZARD

• For outdoor use only. Never use inside house, or other

unventilated or enclosed areas. This heater consumes air

(oxygen). Do not use in unventilated or enclosed areas to

avoid endangering your life.

DANGER

• EXPLOSION - FIRE HAZARD• Never store propane near high heat, open flames, pilot

lights, direct sunlight, other ignition sources or where

temperatures exceed 120 degrees F (49°C).

• Propane vapors are heavier than air and can accumulate

in low places. If you smell gas, leave the area immediately.

• Never install or remove propane cylinder while heater is

lighted, near flame, pilot lights, other ignition sources or

while heater is hot to touch.

• This heater is red hot during use and can ignite

flammables too close to the burner. Keep flammables at

least 3 feet from sides & 2 feet from top. Keep gasoline and

other flammable liquids and vapors well away from heater.

• The propane cylinder must always be stored outdoors in a

well ventilated space. Never store propane cylinder in an

enclosed area (house, garage, etc.). If heater is to be

stored indoors, disconnect the propane cylinder for outdoor

storage.

Caution: Do not attempt to operate until you have read

& understand all General Safety Information in this

manual and all assembly is complete & leak checks

have been performed.

9

. Your heater was designed and approved for outdoor

use only. Do NOT use it inside a building, garage, or

any other enclosed area.. Make sure surrounding areas are free of combustible

materials, gasoline, and other flammable vapors or

liquids.. Ensure that there is no obstruction to air ventilation.. Be sure all gas connections are tight and there are no

leaks.. Be sure the cylinder cover is clear of debris.. Be sure any component removed during assembly or

servicing is replaced and fastened prior to starting.

Before Lighting:. Heater should be thoroughly inspected before each-

use, and by a qualified service person at least

annually.. If relighting a hot heater, always wait at least 5

minutes.. Inspect the hose assembly for evidence of excessive

abrasion, cuts, or wear. Suspected areas should be

leak tested. If the hose leaks, it must be replaced prior

to operation. Only use the replacement hose

assembly specified by manufacturer.

Lighting:

Note: This heater is equipped with a Pilot Light that allows

for safer startups and shutdowns. Pilot must be lit before

Main Burner can be started.

4 Push and release the igniter button until pilot flame is visible through Viewing Hole.

5 Release Control Knob after 30-60 seconds. Pilot

Light will remain lit. If not, return to step 1.

6 Turn Control Knob to ON. Main Burner will light

immediately. Flame is visible through Viewing Hole. If

not, return to step 1.

. If for some reason your igniter fails to deliver a spark,

your heater can be started by inserting a lit match

through the pilot view hole while pushing the control

knob in while in the PILOT position.

1 Turn Cylinder Valve ON.

2 Open Viewing Hole by sliding cover to either side.

3 Push Control Knob IN and rotate to Pilot position.

Note: For initial start or after any cylinder change, hold

Control Knob IN for 2 minutes to purge air from gas lines

before proceeding.

Note: If pilot fails to remain lit, all valves should be closed

and waiiting period of at least 5 minutes should pass before

attempting to light.

Before Turning Gas Supply ON:

10

If you experience any ignition problem please

consult “Troubleshooting” on page 11.

Caution: Avoid inhaling fumes emitted from the

heater’s first use. Smoke and odor from the burning of

oils used in manufacturing will appear. Both smoke

and odor will dissipate after approximately 30 minutes.

The heater should NOT produce thick black smoke.

Note: The burner may be noisy when initially turned on. To

eliminate excessive noise from the burner, turn the Control

Knob to the Pilot position. Then, turn the knob to the level

of heat desired.

WARNINGFOR YOUR SAFETY

Be careful when attempting to manually ignite this heater.

Holding in the control knob for more than 10 seconds

before igniting the gas will cause a ball of flame upon

ignition.

When heater is ON:Emitter screen will become bright red due to intense heat.

The color is more visible at night.

Burner will display tongues of blue and yellow flame. These

flames should not be yellow or produce thick black smoke,

indicating an obstruction of airflow through the burners. The

flame should be blue with straight yellow tops.

If excessive yellow flame is detected, turn off heater and

consult “Troubleshooting” on page 11.

Re-lighting:Note: For your safety, Control Knob cannot be turned OFF

without first depressing Control Knob in PILOT position and

then rotating it to OFF.. Turn Control Knob to OFF.. Wait at least 5 minutes, to let gas dissipate, before

attempting to relight Pilot.. Repeat the “Lighting” steps on prior page.

WARNINGFOR YOUR SAFETY

Heater will be hot after use. Handle with extreme care.

Shut Down:. Turn Control Knob clockwise to Pilot. (Normally,

burner will make a slight popping sound when

extinguished.) Burner will extinguish but Pilot will

remain ON. . To extinguish Pilot, depress Control Knob and

continue to turn it clockwise to OFF.. Turn Cylinder Valve clockwise to OFF and disconnect

Regulator when heater is not in use.

Note: After use, some discoloration of the emitter screen is

normal.

Operation ChecklistFor a safe and pleasurable heating experience, performthis check before each use.

Before Operating:. I am familiar with entire owner’s manual andunderstand all precautions noted .. All components are properly assembled, intact andoperable.. No alterations have been made.. All gas connections are secure and do not leak.. Wind velocity is below 10 mph.. Unit will operate at reduced efficiency below 40°F.. Heater is outdoors (outside any enclosure).. There is adequate fresh air ventilation.. Heater is away from gasoline or other flammableliquids or vapors.. Heater is away from windows, air intake openings,sprinklers and other water sources.. Heater is at least 24" on top and at least 36" on sidesaway from combustible materials.Heater is on a hard and level surface..There are no signs of spider or insect nests..All burner passages are clear..All air circulation passages are clear..Children, pets, clothing, flammable materials anditems that can be damaged from radiant heat areaway from the heater.. Children and adults in the area have been alerted tothe high temperature hazards: especially burns andclothing fires..

.Children and adults in the area have been warned notto touch heater near engine during operation and untilunit has cooled.

After Operation:. Gas control is in OFF position.. Gas Tank valve is OFF.. Disconnect Gas line.. Heater is upright in a secure location.

11

Troubleshooting

If the problem is: And this condition exists: Then do this

Pilot won’t light

Cylinder valve is closed Open valve

Blockage in orifice or pilot tube Clean or replace orifice or pilot tube

Air in gas line

Open gas line and bleed it (pressing control

knob in) for not more than 1 - 2 minutes or until

you smell gas

Low gas pressure with cylinder valve

fully openTurn cylinder valve OFF and replace cylinder

Note: Heater operates at

reduced efficiency below 40ºF

(5ºC)Igniter fails

Use match to light pilot; obtain new igniter and

replace

Pilot won’t stay lit

Dirt built up around pilot Clean dirt from around pilot

Connection between gas valve and

pilot assembly is looseTighten connection and perform leak check

Thermocouple is not operating correctly Replace thermocouple

Burner won’t light

rednilycecalperdnaFFOevlavrednilycnruTwolsierusserpsaG

egakcolbraelCecifironiegakcolB

Control knob is not in ON position Turn control knob to ON

Burner flame is low

rednilycecalperdnaFFOevlavrednilycnruTwolsierusserpsaG

Outdoor temperature is less than 40ºF

and tank is less than 1/4 fullUse a full cylinder

Supply hose is bent or kinked Straighten hose

egakcolbrofsecifirodnarenrubkcehCNOyllufbonklortnoC

Carbon build-up Dirt or film on reflector and burner screen Clean reflector and burner screen

Thick black smoke Blockage in burnerRemove blockage and clean burner inside and

outside

Maintenance

WARNINGFOR YOUR SAFETY:

• Do NOT touch or move heater for at least 45 minutes

after use.

• Reflector is hot to the touch.

• Allow reflector to cool before touching.

To enjoy years of outstanding performance from your

heater, make sure you perform the following maintenance

activities on a regular basis:

Keep exterior surfaces clean.. Use warm soapy water for cleaning. Never use

flammable or corrosive cleaning agents.. While cleaning your unit, be sure to keep the area

around the burner and pilot assembly dry at all

times. Do not submerge the control valve

assembly. If the gas control is submerged in water,

do NOT use it. It must be replaced.

Air flow must be unobstructed. Keep controls, burner,

and circulating air passageways clean. Signs of possible

blockage include:

12

. Gas odor with extreme yellow tipping of flame.. Heater does NOT reach the desired temperature.. Heater glow is excessively uneven.. Heater makes popping noises.

. Spiders and insects can nest in burner or orifices.

This dangerous condition can damage heater and

render it unsafe for use. Clean burner holes by using

a heavy-duty pipe cleaner. Compressed air may help

clear away smaller particles.. Carbon deposits may create a fire hazard. Clean

dome and burner screen with warm soapy water if

any carbon deposits develop.

Note: In a salt-air environment (such as near an ocean),

corrosion occurs more quickly than normal. Frequently

check for corroded areas and repair them promptly.

TIP:Use high-quality automobile wax to help maintain the

appearance of your heater. Apply to exterior surfaces from

the pole down. Do not apply to emitter screen or domes.

Storage

Between uses:. Turn Control Knob OFF.. Disconnect LP source.. Store heater upright in an area sheltered from direct

contact with inclement weather (such as rain, sleet,

hail, snow, dust and debris).. If desired, cover heater to protect exterior surfaces

and to help prevent build up in air passages.

Note: Wait until heater is cool before covering.

During periods of extended inactivity or whentransporting:. Turn Control Knob OFF.. Disconnect LP source and move to a secure,

well-ventilated location outdoors.

. Store heater upright in an area sheltered from direct

contact with inclement weather (such as rain, sleet,

hail, snow, dust and debris).. If desired, cover heater to protect exterior surfaces

and to help prevent build up in air passages.. Never leave LP cylinder exposed to direct sunlight or

excessive heat.

Note: Wait until heater is cool before covering.

Service

Warranty

Repair to gas passages and associated components

should be done only by a qualified service person.

Caution: Always allow heater to cool before

attempting service.

Manufactured by:Changzhou Gardensun Furnace Co., Ltd.No. 1, Boyi Town, Changzhou City,Jiangsu Province P.R. China

1 YEAR LIMITED WARRANTY - CUSTOMERS IN CANADAIMPORTANT

Only return this product to the store if it was purchased within 90 days. If you have problems af ter 90 days of purchase, please email our customer service department for any questions or concerns: www.patioheaterpartsonline.com OR PLEASE CALL 888-775-1330 DATED PROOF OF PURCHASE REQUIRED FOR WARRANTY SERVICE.

WARRANTYThis product is inspected, tested and carefully packaged to minimize the chance of damage during shipment. If a part (excluding light bulbs and fuses*) within one year from the date of purchase proves to be defective in material or fabrication under normal use, the part will be repaired or replaced. The Company's obligation under the warranty is to replace or repair defective parts at our discretion. Any expenses or damage resulting from the installation, removal or transportation of the product will the responsibility of the owner and are not covered by this warranty.The owner assumes all other risks arising out from the use or misuse of the product. The warranty will be void if the product damage or failure is deemed by the Company to be caused by accident, alteration, misuse, abuse, incorrect installation or removal, or connection to an incorrect power source by the owner.The Company neither assumes, nor authorizes any person or entity to assume for it any obligation or liability associated with its products. * Light bulbs and fuses are not covered under this warranty. If you have any questions regarding the warranty or service, please call our toll free number: 888-775-1330

Distributed by:AZ Patio Heaters8550 N 91st Ave Ste C-25Peoria, AZ 85345