Plasma Display September 2001 Digital Media Systems Division

SERVICE MANUAL (Rev.D)

ＲＧＢ/ＶＩＤＥＯ ＭＥＮＵ ＳＥＬＥＣＴ ＶＯＬＵＭＥ

ＳＴＡＮＤＢＹ（ＲＥＤ）

ＯＮ　　　　　（ＧＲＮ）

ＨＩＴＡＣＨＩ

Be sure to read this manual before servicing. To assure safety from fire, electric shock, injury, harmful radiation and materials, various measures are provided in this Hitachi Plasma display. Be sure to read cautionary items described in the manual to maintain safety before servicing.

1. Since Panel Module and front Filter are made of glass, handling to the broken Module and Filter shall be taken care sufficiently in order not to be injured.

2. Replacing work shall be started after the Panel Module and the AC/DC Power supply become sufficiently cool.

3. Special care shall be taken to the display area in order not to damage its surface. 4. The Panel Module shall not to be touched with bare hand to protect its surface from stains. 5. It recommended to use clean soft gloves during the replacing work in order to protect not

only the display area of the Panel Module but also a serviceman himself. 6. The Chip Tube of Panel Module (located upper left of the back) and flexible cables

connecting Panel glasses to drive circuit PWBs are very weak, so shall be taken care sufficiently not break. If you break Chip Tube, the Panel doesn’t display forever.

1. Features 2 2. Specifications 2 3. Names of each part. 3 4. Trouble shooting 4

5. Block diagram 6 6. Disassembly diagram 7 7. Re-Adjustment 11 8. Replacement Parts list 14

SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT.

SM0059

CMP307XE CMP307XU

Caution

Contents

Serviceman Warning

1. Features 37 inches XGA high-definition color plasma display panel Newly developed Multi-scanning converter provides a multiscan coverage of TV signals through to PC analog signals (24kHz to SXGA(64kHz)) Large high-quality display images free from color misconvergence and display distortion, as well as from geomagnetic effect and the magnetic effect of ambient power lines

2. Specifications PDP Module 37 inches XGA PDP panel (aspect ratio 4:3)

Description FPF37C12896UA Pixel pitch 0.735 mm(H) x 0.735 mm(V) Pixel structure RGB striped Brightness 150cd/m2 (typical) with front filter Contrast 400:1 (typical) in dark room

RGB 1 (mD-15p)

RGB 2 (BNCx5)

Video : 0.7 Vp-p Sync. : Separate H/V, TTL level Composite H/V, TTL level Sync. on Green at 0.30 Vp-p

Video 1 (RCA Pinx1, S-terminalx1)

Composite Video or S-video (for S2) NTSC3.58 Video : Composite 1.0 V S-video Y: 1.0 Vp-p, C:0.29Vp-p Sync. : Composite sync

Input Signal

Video 2 (RCA Pinx3)

Component Video Y,Pb,Pr or Y,Cb,Cr: (480i,480P,1080i,1035i) Video : Y : 1.0 Vp-p Pb/Cb,Pr/Pr : 0.7 Vp-p Sync. : Superimposed with Y signals

Colors 2.09 million Synchronization Horizontal : 24 – 64 kHz

Vertical : 50 - 75 Hz Resolution Horizontal : 1024 dots (max.)

Vertical : 768 lines (max.) Viewable Image Size 37 inches (940 mm), diagonal (typical)

Viewable Image Area Horizontal : 753 mm (typical) Vertical : 564 mm (typical)

Color Temperature NORM(9300 K) Warm-up Time 30 minutes to reach optimum performance level. Power Supply AC 100 - 120 / 200 - 240 V (4.3A /2.2A)

50/60 Hz (automatically selected) Power Consumption : 390 W (typical) (provided with power save circuit.)

Dimensions 884 (W) x 684 (H) x 99.7 (D) mm (without stand) 884 (W) x 766 (H) x 300 (D) mm (with stand)

Weight 29.8 kg (approx.) without stand 32.8 kg (approx.) with stand

Environmental Condition

Operation Storage Temperature 5ºC to 35ºC 0ºC to 50ºC Humidity 20% to 80% 20% to 80%

2

3. Names of each part Outlook

Input terminal(D-sub connector)

Pin No. Signal 1 Red Video 2 Green Video (Sync. optional) 3 Blue Video 4 No connection 5 No connection 6 Red Ground 7 Green Ground 8 Blue Ground 9 No connection 10 Ground 11 No connection 12 SDA 13 H.Sync. (or H/V composite) 14 V.Sync. 15 SCL

Message table ☛ Onscreen display

Indication Condition The monitor indicates the message “POWER SAVE”.

The monitor detects no sync. signal.

The monitor indicates the message “OUT OF FREQUENCY”.

The monitor detects a sync. signal which is out of specification, or unstable.

3

ＲＧＢ/ＶＩＤＥＯ ＭＥＮＵ ＳＥＬＥＣＴ ＶＯＬＵＭＥ

ＳＴＡＮＤＢＹ（ＲＥＤ）ＯＮ　　　　　（ＧＲＮ）

ＨＩＴＡＣＨＩ

ＦＲＯＮＴ　ＶＩＥＷ

ＦｒｏｎｔＦｒａｍｅ

ＰｏｗｅｒＳｗｉｔｃｈ

ＣｏｎｔｒｏｌＳｗｉｔｃｈｅｓ

ＳＴＡＮＤ

ＦｒｏｎｔＦｉｌｔｅｒ

LISTED

7J88UL1950

WARNING/AVERTISSEMENT/VORSICHT/PRECAUCION

S/N

JUNE/JUIN 1999

Y9G000001

CMP402HD

100-120V/220-240V～50-60Hz, 5A/2.5A

USC

2

PLASMA DISPLAY/ECRAN A PLASMAMOD. NO./MOD. N .o

必ずア－ス接続を行って下さい。

（ＭＯＮＯ）ＬＲ Ｖ Ｈ Ｂ Ｇ Ｒ

ＲＧＢ １〔Ｄ－Ｓ ＵＢ〕

ＲＧＢ２〔ＢＮＣ〕ＲＧＢ　ＩＮＰＵＴ

ＡＵＤＩＯ

ＱＬ０９００１

ＲＳ２３２Ｃ ＩＮ

ＲＥＡＲ　ＶＩＥＷ

ＲｅａｒＣｏｖｅｒ

ＡＣ　ｉｎｌｅｔ

ＭＡＩＮ　ＳＷＩＴＣＨ

ＶＩＤＥＯ２ ＩＮＰ ＵＴ

Ｒ Ｌ Ｒ Ｂ Ｙ

ＡＵＤＩ Ｏ（ＭＯＮＯ）

Ｂ

〔 ＣＯＭＰＯ ＮＥＮ Ｔ〕

Ｒ

Ｐ　 ／Ｃ Ｐ　／Ｃ

Ｒ Ｌ ＶＩＤＥＯ Ｓ－ ＶＩＤＥＯ

ＶＩＤＥＯ１　ＩＮＰＵＴ（ＭＯＮＯ）

ＡＵＤＩＯ

ＲＧＢ　ｉｎｐｕｔ　Ｔｅｍｉｎａｌｓ

Ｖｉｄｅｏ ｉｎｐｕｔ　Ｔｅｍｉｎａｌｓ

Front Filter

Front Frame

Power Switch

FRONT VIEW Control Switch

STAND (Option)

Rear Cover

RGB input terminals Video input terminals REAR VIEW

AC inlet

MAIN SWITCH

Yes

Yes

4. Trouble shooting

Are Voltage

applied to pins7,11(PSD3) of the Signal PWB ?

Signal PWB

Speaker

Power can not be turned on (LED is not light)

Is the input voltage applied to the AC/DC

Power unit ? (PESW1 4, 6)

No

Yes AC inlet Power switch AC Fuse

F911 10A250V

7 : +5.6V 11 : +4.4V 9 : GND

AC/DC Power unit

No

Yes

Picture is displayed. But no sound

Are Voltage

applied to pins 4(PSD3) of the Signal PWB ?

No

AC/DC Power unit 4 : 14V

5 : GND

No Are there signals on

Speaker ?

Signal PWB

4

No

No

red

Yes

high (5V)

low (0V)

Yes

No

No

green

Yes

Yes

1 : +180V 4 : GND

No

9 : GND 11 : +4V

Yes

5 : GND 7 : +5.6V

Yes

See page 6

Is Voltage of the pin 2(PSC1) on the Signal PWB

high?

Is the LED redor green?

Picture is not displayed (LED is lighting)

No

AC/DC Power unit

Signal PWB

AC/DC Power unit

Do the Fans rotate?

When disconnect

PF1-3 of the AC/DC Power unit, the picture

Is displayed ?

DC Fan

AC/DC Power unit

Is Voltage of the pin 5(PED)

on the AC/DC Power unit 5V

AC/DC Power unit

Are Voltages of the pin 1(PEY1)

on the AC/DC Power unit collect ?

Is Voltage of the pin 9, 11(PED) on the AC/DC Power

unit collect ?

Panel Module

Panel Module

AC/DC Power unit

Are Voltage

applied to pins 7(PED) of the Signal PWB?

5

PAY4

PAY4

PAY3

PAY3

PED

PED

EEF6

ESV1

ESV2

ESV3

PSD1

PSD1

PEY

PEY1

PXY1

PXY2

PX08 PX07

PX05 PX06

PXY2

PXY1

Y UP

Y DW

DC-DC Y_SCAN

X_SCAN

SIGNAL DIGITAL

VIDEO

AC-DC POWER

ADDRESS UP/RI

PESW1

ADDRESS UL/LF

X DW

X

UP

ADDRESS DW/RI ADDRESS DW/LF

AC INLET

USPL

SP

USPR

POWER SW

CONTROL

LED PSC2

MFN3

MFN2

MFN1

1

1

1

1

45

45

1

45

1 45

1

40 40

1 40

1

PAX2

PAX1

40

40 1

1

40 40

4 1

8

6

1

1

1

1

1

1

12

12

1

1

1

1 1

1 1

1

1

1

12

12 1

1

8 1

7

7

1

1

13

19

11 1

7

7 5

5 5

5 3

3

PSS

1

45

45

1

PY01

PY03

PY02

PY04

45

1 45

40 1

40 1

40 1

1

1

1

1

13

19

11

40 1

40 1

1 40

1

1 1

5

5 5

1 5

5

5

PDYPDY

PDY

PDYPDY

PDY

PDXPDX

PDX

PDXPDX

PDX

40 1

40 1

40 1

40 1

40 1

40 1

40 1

40 1

40 1

180v VADR(70V),+5V

VADR(70V),+14V,,+5V

VSUS(180V)

VXSC(60V)

VRES(340V)

VADR(70V)

VXSC(60V)

VRES(340V)

VYSC(70V)

VYSB(-170V)

+14V

+5V

4V,5.6V.14V,

STB-5V

4V,5.6V.14V

4V,5.6V.14V SW.REG.

SW.REG.

5V,VADR(70V)

5. BLOCK DIAGRAM

6

40 1

40 1

PAX5

PAX6

PST

PAY1 PAY2

PAY1 PAY2

PSD3

PSD3 PST PSD2

PSD2

PSC1

PSC2

PAX4 PAX8

PAX7 PAX3

PSC1

6. Disassembly diagram (1) Remove Back Cover Be careful not to be damaged the face

of Front Filter. Remove 4 screws(a) and remove the Rear stand.

Remove 20 screws(b) ､ and remove Back Cover.

At this time be careful not to be damaged edges of Back Cover and its coated face.

7

LISTED

7J88UL1950

WARNING/AVERTISSEMENT/VO RSICHT/PRECA UCION

S/NJUNE/JUIN 1999

Y9G000001

CMP402HD

100-120V/220-240V～50-60Hz, 5A/2.5A

USC

2

PLASMA DISPLAY/ECRAN A PLASMAMOD. NO./MOD. N .o

必ずア－ス接続を行って下さい。

（ＭＯＮＯ）

ＬＲ Ｖ Ｈ Ｂ Ｇ Ｒ

ＲＧ Ｂ １

〔 Ｄ － Ｓ Ｕ Ｂ 〕

ＲＧＢ２〔ＢＮＣ〕ＲＧＢ　ＩＮＰＵＴ

ＡＵＤＩＯＱＬ０９００１

ＲＳ２３２Ｃ ＩＮ

Ｓｃｒｅｗ（ａ）

ＶＩＤＥＯ ２ Ｉ Ｎ Ｐ Ｕ Ｔ

Ｒ Ｌ Ｒ Ｂ ＹＡ ＵＤ Ｉ Ｏ

（ＭＯＮＯ）

Ｂ

〔 Ｃ Ｏ Ｍ Ｐ Ｏ ＮＥ Ｎ Ｔ 〕

Ｒ

Ｐ 　 ／ Ｃ Ｐ　／ＣＲ Ｌ ＶＩ Ｄ Ｅ Ｏ Ｓ － ＶＩ Ｄ Ｅ Ｏ

ＶＩＤＥＯ１　ＩＮＰＵＴ（ＭＯＮＯ）

ＡＵＤＩＯ

Screw(a)

Ｑ Ｌ０ ９０ ０１

ＲＳ２３２Ｃ ＩＮ（ＭＯＮＯ）

ＬＲ Ｖ Ｈ Ｂ Ｇ Ｒ

Ｒ Ｇ Ｂ１

〔 Ｄ － ＳＵ Ｂ 〕

ＲＧＢ２〔ＢＮＣ〕ＲＧＢ　ＩＮＰＵＴ

ＡＵＤＩＯ

Ｓｃｒｅｗ（ｂ）

Ｓｃｒｅｗ（ｂ） Ｓｃｒｅｗ（ｂ）

Ｓｃｒｅｗ（ｂ）

Ｓｃｒｅｗ（ｂ） Ｓｃｒｅｗ（ｂ）

ＶＩＤＥＯ ２ Ｉ Ｎ Ｐ Ｕ Ｔ

Ｒ Ｌ Ｒ Ｂ ＹＡ Ｕ Ｄ Ｉ Ｏ

（ＭＯＮＯ）

Ｂ

〔 Ｃ Ｏ Ｍ Ｐ ＯＮ Ｅ Ｎ Ｔ 〕

Ｒ

Ｐ 　 ／ Ｃ Ｐ　／Ｃ

Ｒ Ｌ Ｖ Ｉ Ｄ Ｅ Ｏ Ｓ－ Ｖ Ｉ Ｄ ＥＯ

ＶＩＤＥＯ１　ＩＮＰＵＴ（ＭＯＮＯ）

ＡＵＤＩＯ

Screw(b)

Screw(b)

Screw(b) Screw(b)

Screw(b) Screw(b)

(2) Remove Signal PWB

Disconnect ESC1(PH-3P), ESC2(PH-7P), ESS(EH4P-HR3P/HR2P), ESD3(EH-12P), ESD2(FFC-40P) , PSD1(FFC-40P) PST ,ESV3,EVC2, EVC1 connectors.

Be careful not to be damaged the PSV1-3 Connector holder. Remove 2 screws(c), 8screws(f), plastic rivet, 4screws(e) 2screws(g) and remove Signal PWB,and Video PWB.

(3) Remove filter PWB Disconnect P902A, PESW1 connector.

Remove 4screws(d) and remove the filter cover. Then remove 4screws(g), and remove Filter PWB.

8

ＳＩＧＮＡＬＰＷＢ

ＶＩＤＥＯＰＷＢ

Ｓｃｒｅｗ（ｃ） Ｓｃｒｅｗ（Screw(c) Screw(c)

Ｓｃｒｅｗ（ｆ）

Ｐｌａｓｔｉｃ　ｒｉｖｅｔ

Ｓｃｒｅｗ（ｇ）

Ｓｃｒｅｗ（ｅ）

Ｓｃｒｅｗ（ｅ）

Ｓｃｒｅｗ（ｆ）

Screw (e)

Screw (e)

Screw (g)

Plastic rivet

Screw (f) Screw (f)

Ｓｃｒｅｗ（ｄ）

Ｓｃｒｅｗ（ｇ）

ＦｉｌｔｅｒＣｏｖｅｒ

Filter Cover

Screw (d)

Screw (g)

(4) Remove Front Frame Remove 3 screws(l),then be careful not to be damaged the face of front filter. Attached the Stand with 4screw(a), then stand it vertically. When remove front frame.

(5) Remove Front Filter(Glass)

Remove 22 screws(m), and remove Filter hold Metal and Front Filter. Be careful not to fall down the front Filter. When remove the filter hold Metal. When attach the new Front Filter, remove protection film on a side(yellow tag is marked).Then attach to the Front Frame, locating the conducting electrode side to the inside, and attach Filter hold Metal.

Ｓｃｒｅｗ（ｍ） Ｓｃｒｅｗ（ｍ）

Ｓｃｒｅｗ（ｍ） Ｓｃｒｅｗ（ｍ）Ｍａｉｎ　ｆｒａｍｅ

Ｓｃｒｅｗ（ｍ） Ｓｃｒｅｗ（ｍ）

Ｆｒｏｎｔ　Ｆｉｌｔｅｒ（Ｇｌａｓｓ）

Screw(m)

Screw(m)

Front Filter (Glass)

Screw(m) Screw(m)

Screw(m)

Screw(m)

Filter holder metal

9

Ｓｃｒｅｗ（ｌ）

Ｆｒｏｎｔ Ｆｒａｍｅ

Ｓｃｒｅｗ（ａ）

Screw (ｌ)

Front Frame

Screw (ａ)

(6) Remove Fan Remove 3screws(k),and disconnect AEF6orBEF6 connector, Remove Fan hold Metal. Then remove 2plastic rivets.

(7) Remove AC/DC Power unit Remove 4 screws(o) and 2 screw(p), then disconnect PESW1(VH-6P), PEY1(VH-5P), PED(EH-12P), PF1(EH-3P), PF2(EH-3P), PF3(EH-3P) connectors.

10

Ｐｒａｓｔｉｃ　ｒｉｖｅｔ

Ｆａｎ　Ｍｅｔａｌ

Ｓｃｒｅｗ（ｋ）

AEF6/BEF6ｃｏｎｎｅｃｔｏｒ

Plastic rivet

AEF6/BEF6 Connector

Screw (ｋ)

Ｆａｎ Ｍｅｔａｌ

Ｓｃｒｅｗ（ｏ） Ｓｃｒｅｗ（ｐ）

Screw (o) Screw (p)

Fan Metal

7. Re-Adjustment After changing the Signal PWB or Panel Module, re-adjustment is needed according to the item 7.1 to 7.5 For Video PWB, item 7.3 to 7.5 are needed.

7.1 Personal Computer (PC)input black level/fundamental amplitude adjustment How to Prepare 1.Connect RGB input terminal XGA(Vertical Sync Frequency 60Hz),0.7Vpeak,no -set up. 2.Appear and Adjust screen OSD Menu of Picture: Contrast:127 Brightness:0, Color Select :MID, Video level :0.7V.

How to Adjust 1.Set Service Adjustment Mode and adjust as follows by Remote Control Transmitter (7.5 Refer How to set to Service Adjustment Mode) 2.Set Adjustment No.35,36 ,and 37 scale to 255 3.Input full black level Signal 4.Set Adjustment No.41 to changing point from black to Red(set to black point) 5.Set Adjustment No.42 to changing point from black to Green(set to black point) 6.Set Adjustment No.43 to changing point from black to Blue(set to black point) 7.Input all white level Signal 8.Set Adjustment No.44 to changing point from Red to black(set to black point) 9.Set Adjustment No.45 to changing point from Green to black(set to black point) 10.Set Adjustment No.46 to changing point from Blue to black(set to black point) Tolerances of each color adjustment numbers are less than 10, if more than 10, Re-adjust from above 2 steps.

7.2 PC color temperature adjustment How to prepare 1.Connect RGB input terminal XGA(Vertical Sync Frequency 60Hz),0.7Vpeak, without set up signal. 2.Window color (R,G and B)should be 255 each. and input white window(33%) Signal. 2.Appear and Adjust screen OSD Menu of Picture: Contrast:127, Brightness:0,GAMMA:2.2,Video level:0.7V

How to Adjust 1.Set Service Adjustment Mode and adjust as follows by Remote Control Transmitter. 2.Mesurement probe of CRT Color Analyzer CA-100 is set on the center of screen. (Center of white window signal)

11

3.Adjust color temperature as follows by increasing or reducing numbers of NO.32,33,34. PC color temperature (COOL) x=0.277±±±±0.002, ｙｙｙｙ=0.289±±±±0.002 at 10400K 4.Adjust color temperature as follows by increasing or reducing numbers of NO.35,36,37. PC color temperature (NORM) x=0.283±±±±0.002, y=0.298±±±±0.002 at 9300K 5.Adjust color temperature as follows by increasing or reducing numbers of NO.38,39,40. PC color temperature (WARM) x=0.313±±±±0.002, y=0.329±±±±0.002 at 6500K Suggestion 1.Luminance of panel surface is less than 20lux to arrange adjustment environment 2.Color select mode is automatically set to COOL while adjustmentNo.32,33 and 34. 3.Color select mode is automatically set to NORM while adjustmentNo.35,36 and 37. 4.Color select mode is automatically set to WARM while adjustmentNo.38,39 and 40.

7.3 Video input black level/fundamental amplitude adjustment How to Prepare 1.Connect Video input ( NTSC 3.58), Video level 0.714Vp-p, Sync level 0.286Vp-p, no set up 2.Appear and Adjust screen OSD Menu of Picture: Contrast: 127 Brightness:0, Video level: NORMAL, Color Select: MID

How to Adjust 1.Set Service Adjust Mode and adjust as follows by Remote Control Transmitter 2.Set Adjustment No.35,36, and 37 scale to 255 3.Input all black level Signal 4.Set Adjustment No.41 to changing point from black to Red(set to black point) 5.Set Adjustment No.42 to changing point from black to Green(set to black point) 6.Set Adjustment No.43 to changing point from black to Blue(set to black point) 7.Input all white level Signal 8.Set Adjustment No.44 to changing point from Red to black(set to black point) 9.Set Adjustment No.45 to changing point from Green to black(set to black point) 10.Set Adjustment No.46 to changing point from Blue to black(set to black point) Tolerances of each color adjustment numbers are less than 20, if more than 20, Re-adjust from above 2 steps.

12

7.4 Video color temperature adjustment How to prepare 1.Connect Video input ( NTSC 3.58), Video level 0.714Vp-p ,Sync level 0.286Vp-p,no -set up 2.Input white window(33%) Signal. 2.Appear and Adjust screen OSD Menu of Picture: Contrast:127 ,Brightness:0,Video level:NORMAL,GAMMA:2.2

How to Adjust 1.Set Service Adjust Mode and adjust as follows by Remote Control Transmitter. 2.Mesurement probe of CRT Color Analyzer CA-100 is set on the center of screen. (Center of white window signal) 3.Adjust color temperature as follows by increasing or reducing numbers of NO.32,33,34. Video color temperature (COOL) x=0.269±±±±0.002, y=0.266±±±±0.002 at 14100K 4.Adjust color temperature as follows by increasing or reducing numbers of NO.35,36,37. Video color temperature (NORM) x=0.287±±±±0.002, y=0.287±±±±0.002 at 9400K 5.Adjust color temperature as follows by increasing or reducing numbers of NO.38,39,40. Video color temperature (WARM) x=0.314±±±±0.002, y=0.315±±±±0.002 at 6500K Suggestion 1.Luminance of panel surface is less than 20lux to arrange adjustment environment 2.Color select mode is automatically set to COOL while adjustmentNo.32,33 and 34. 3.Color select mode is automatically set to NORM while adjustmentNo.35,36 and 37. 4.Color select mode is automatically set to WARM while adjustmentNo.38,39 and 40.

7.5 How to set to Service Adjustment Mode Turn off the sub power button( or power button on the Remote Control Transmitter) then pushing RGB/VIDEO and SELECT buttons located on the bottom of the set and turn on the sub power button until “Service Adj. Mode” OSD is appeared( more than 5 seconds) When fall out from Service Adjust Mode, turn off the sub power button( or power button

on the Remote Control Transmitter).

13

THE UPDATED PARTS LIST

FOR THIS MODEL IS

AVAILABLE ON ESTA

Hitachi, Ltd. Tokyo, Japan International Sales Division

THE HITACHI ATAGO BUILDING, No. 15 –12 Nishi Shinbashi, 2 – Chome,

Minato – Ku, Tokyo 105-8430, Japan. Tel: 03 35022111

HITACHI EUROPE LTD, Whitebrook Park Lower Cookham Road Maidenhead Berkshire SL6 8YA UNITED KINGDOM Tel: 01628 643000 Fax: 01628 643400 Email: consumer-service@hitachi-eu.com

HITACHI EUROPE S.A. 364 Kifissias Ave. & 1, Delfon Str. 152 33 Chalandri Athens GREECE Tel: 1-6837200 Fax: 1-6835964 Email: service.hellas@hitachi-eu.com

HITACHI EUROPE GmbH Munich Office Dornacher Strasse 3 D-85622 Feldkirchen bei München GERMANY Tel: +49-89-991 80-0 Fax: +49-89-991 80-224 Hotline: +49-180-551 25 51 (12ct/min) Email: HSE-DUS.service@hitachi-eu.com

HITACHI EUROPE S.A. Gran Via Carlos III, 101-1 08028 Barcelona SPAIN Tel: 93 409 2550 Fax: 93 491 3513 Email: atencion.cliente@hitachi-eu.com

HITACHI EUROPE srl Via Tommaso Gulli N.39, 20147 Milano, Italia ITALY Tel: +39 02 487861 Tel: +39 02 38073415 Servizio Clienti Fax: +39 02 48786381/2 Email: customerservice.italy@hitachi-eu.com

HITACHI Europe AB Box 77 S-164 94 Kista SWEDEN Tel: +46 (0) 8 562 711 00 Fax: +46 (0) 8 562 711 13 Email: csgswe@hitachi-eu.com

HITACHI EUROPE S.A.S Lyon Office B.P. 45, 69671 BRON CEDEX FRANCE Tel: 04 72 14 29 70 Fax: 04 72 14 29 99 Email: france.consommateur@hitachi-eu.com

HITACHI EUROPE LTD (Norway) AB STRANDVEIEN 18 1366 Lysaker NORWAY Tel: 67 5190 30 Fax: 67 5190 32 Email: csgnor@hitachi-eu.com

HITACH EUROPE AB Egebækgård Egebækvej 98 DK-2850 Nærum DENMARK Tel: +45 43 43 6050 Fax: +45 43 60 51 Email: csgnor@hitachi-eu.com

HITACHI EUROPE AB Neopoli / Niemenkatu 73 FIN-15140 Lahti FINLAND Tel : +358 3 8858 271 Fax: +358 3 8858 272 Email: csgnor@hitachi-eu.com

Hitachi Europe Ltd Bergensesteenweg 421 1600 Sint-Pieters-Leeuw BELGIUMTel: +32 2 363 99 01 Fax: +32 2 363 99 00 Email: sofie.van.bom@hitachi-eu.com

HITACHI EUROPE LTD Na Sychrove 975/8 101 27 Pr aha 10 – Bohdalec CZECH REPUBLIC Tel: +420 267 212 383 Fax: +420 267 212 385 Email: csgnor@hitachi-eu.com

www.hitachidigitalmedia.com