hit_7065_epd

SURPASS hiT 7065 5.05

Environmental Product Declaration (EPD) A42022-L5982-A160-01-7632

Nokia Siemens Networks

1 (19)

Statements of compliance

2 (19) A42022-L5982-A160-01-7632Issue 1 Issue date: August 2010

The information in this document is subject to change without notice and describes only the product defined in the introduction of this documentation. This documentation is intended for the use of Nokia Siemens Networks customers only for the purposes of the agreement under which the document is submitted, and no part of it may be used, reproduced, modified or transmitted in any form or means without the prior written permission of Nokia Siemens Networks. The documentation has been prepared to be used by professional and properly trained personnel, and the customer assumes full responsibility when using it. Nokia Siemens Networks welcomes customer comments as part of the process of continuous development and improvement of the documentation. The information or statements given in this documentation concerning the suitability, capacity, or performance of the mentioned hardware or software products are given as is and all liability arising in connection with such hardware or software products shall be defined conclusively and finally in a separate agreement between Nokia Siemens Networks and the customer. However, Nokia Siemens Networks has made all reasonable efforts to ensure that the instructions contained in the document are adequate and free of material errors and omissions. Nokia Siemens Networks will, if deemed necessary by Nokia Siemens Networks, explain issues which may not be covered by the document. Nokia Siemens Networks will correct errors in this documentation as soon as possible. IN NO EVENT WILL NOKIA SIEMENS NETWORKS BE LIABLE FOR ERRORS IN THIS DOCUMENTATION OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL, DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES, SUCH AS BUT NOT LIMITED TO LOSS OF PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESS OPPORTUNITY OR DATA,THAT MAY ARISE FROM THE USE OF THIS DOCUMENT OR THE INFORMATION IN IT. This documentation and the product it describes are considered protected by copyrights and other intellectual property rights according to the applicable laws. The wave logo is a trademark of Nokia Siemens Networks Oy. Nokia is a registered trademark of Nokia Corporation. Siemens is a registered trademark of Siemens AG. Other product names mentioned in this document may be trademarks of their respective owners, and they are mentioned for identification purposes only. Copyright Nokia Siemens Networks 2010. All rights reserved.

f Important Notice on Product Safety Elevated voltages are inevitably present at specific points in this electrical equipment.Some of the parts may also have elevated operating temperatures. Non-observance of these conditions and the safety instructions can result in personal injury or in property damage. Therefore, only trained and qualified personnel may install and maintain the system. The system complies with the standard EN 60950 / IEC 60950. All equipment connected has to comply with the applicable safety standards. The same text in German: Wichtiger Hinweis zur Produktsicherheit In elektrischen Anlagen stehen zwangslufig bestimmte Teile der Gerte unter Spannung. Einige Teile knnen auch eine hohe Betriebstemperatur aufweisen. Eine Nichtbeachtung dieser Situation und der Warnungshinweise kann zu Krperverletzungen und Sachschden fhren. Deshalb wird vorausgesetzt, dass nur geschultes und qualifiziertes Personal die Anlagen installiert und wartet. Das System entspricht den Anforderungen der EN 60950 / IEC 60950. Angeschlossene Gerte mssen die zutreffenden Sicherheitsbestimmungen erfllen


A42022-L5982-A160-01-7632 Issue 1 Issue date: August 2010

3 (19)

In addition to above, this document is also intended for the use of Nokia Siemens Networks recycling service providers responsible for the end-of-life treatment of the product defined in this document. The foregoing disclaimer shall also be applicable and binding on all such recycling service providers.




CE statement

The CE conformity declaration for the product is fulfilled when the system is built and cabled in line with the information given in the manual and the documentation specified within it, such as installation instructions, cable lists or the like. Where necessary project-specific documentation should be taken into consideration. Deviations from the specifications or independent modifications to the layout, such as use of cable types with lower screening values for example, can lead to violation of the CE protection requirements. In such cases the conformity declaration is invalidated. The responsibility for any problems which subsequently arise rests with the party responsible for deviating from the installation specifications.

Contents


5 (19)

Contents

1 Introduction ............................................................................................7

2 Product description ...............................................................................8

3 Company environmental information...................................................9 3.1 Nokia Siemens Networks environmental policy .......................................9 3.2 Life cycle thinking.....................................................................................9 3.3 Environmental Management System .....................................................10 3.4 Design for Environment..........................................................................10

4 Product environmental information ...................................................11 4.1 Product energy consumption..................................................................11 4.2 Product CO2 footprint.............................................................................11 4.3 Materials.................................................................................................12 4.3.1 Nokia Siemens Networks Substance List...............................................12 4.3.2 Product end-of-life ..................................................................................13 4.3.3 Main material fractions ...........................................................................13 4.3.4 Components and substances which may require special

handling in the end-of-life phase ............................................................13 4.4 Product recyclability rate ........................................................................16 4.5 Batteries [optional chapter].....................................................................16 4.6 Acoustic noise emission.........................................................................16 4.7 Product delivery packaging ....................................................................17

5 Environment related markings............................................................18 5.1 EU WEEE marking of separate collection ..............................................18

6 Take-back information.........................................................................19

Summary of changes


Summary of changes Issue Issue Date Remarks

1 September 2010 Initial version

0BIntroduction


7 (19)

1 Introduction The purpose of this document is to provide environmentally relevant information of a specific Nokia Siemens Networks product.

This document shall not be interpreted as a specification, modification or amendment to the specification, or additional or other warranty of any kind. In case of discrepancy between this document and the Product specification or terms and conditions of the valid supply agreement between Nokia Siemens Networks and the customer, the supply agreement and Product specification shall always prevail over this document.


2 Product description Type of the product Next Generation SDH

Product name SURPASS hiT 7065

Product configuration

NSN code / product ID

Company environmental information


9 (19)

3 Company environmental information 3.1 Nokia Siemens Networks environmental policy

Nokia Siemens Networks strives through the creation of innovative products to improve the quality of life the world over and maximize the benefits of Information and Communication Technology (ICT).

As a global company we are facing special responsibility for worldwide long-term challenges and take seriously our responsibility for environmental protection and resource stewardship.

Sustainability is the key to securing our companys future. Central to this thinking is meeting the demands of business in an ecologically and socially progressive manner. A demonstrated commitment to environmental protection will increase the competitive advantage of businesses and our customers and lay the foundation for a successful future.

Our global system for managing environmental protection ensures continuous improvement of our environmental performance. We design, develop, manufacture and market our products and services in a manner that meets or exceeds applicable regulations and minimizes the impact on natural resources.

Our management and employees act in accordance with this policy and observe the relevant regulations. We are taking also extended company responsibility and are requiring our contractors to act according to this policy.

3.2 Life cycle thinking

The environmental goals and activities of Nokia Siemens Networks are aimed at reducing the environmental impact of Nokia Siemens Networks

Company environmental information


products over their entire life cycle. Life-cycle thinking is used throughout the products phases from raw material extraction, manufacturing operations, use phase and end-of-life practices as well as logistics. Continuous activities on these fields assure to minimize the environmental impacts of our products.

3.3 Environmental Management System

Nokia Siemens Networks is increasingly concerned with achieving and demonstrating sound environmental performance by controlling the impacts of their activities, products and services on the environment.

Therefore ISO 14001 international standard covering environmental management, provides Nokia Siemens Networks with the elements of an effective management system. Additionally all manufacturing sites of Nokia Siemens Networks are certified by an external body according to ISO 14001.

3.4 Design for Environment

Design for Environment (DfE) means systematic integration of environmental objectives into product design. In Nokia Siemens Networks, products are designed to be environmentally efficient by integrating several tasks to product process performing to

minimize material and energy use maximize reuse and recycling minimize use of materials harmful to the environment design products to be easily or remotely maintainable or

maintenance free.

DfE is an integral part of Product Process in NSN and thus considered in day-to-day decision making in Nokia Siemens Networks.

Product environmental information


11 (19)

4 Product environmental information 4.1 Product energy consumption

W Comment

maximum traffic 1500 FAN full speed run

typical (50%) traffic 680

low/no traffic 380

Units having significant impact to product energy consumption

Comment

FAN 250 W under full speed, 45 W under normal speed

Switch card 50W max.

The special energy saving features of product

Comment

FAN speed control Low speed under 25 centigrade environment temperature

4.2 Product CO2 footprint

Unit Data



Unit Data

Product energy consumption, typical (50%) traffic

kW 0,68

Average time of use year 10

CO2 emission (Location reference)

Kg/kWh 0,372 (Europe energy mix)

Total Kg 22,159

Units having significant impact to product CO2 footprint

Comment

FAN 250 W under full speed, 45 W under normal speed

Switch card

4.3 Materials

4.3.1 Nokia Siemens Networks Substance List

Nokia Siemens Networks has compiled a Substance List based on regulatory requirements and reasonable facts. The Substance List identifies substances in two categories:

Banned or restricted substances category identifies substances that are banned or restricted in applications (solders, pastes, etc.), parts, subassemblies and accessories related to Nokia Siemens Networks products and/or packaging.

Monitored substances category lists substances that Nokia Siemens Networks expects, based on reasonable facts, to be reduced or phased out from Nokia Siemens Networks products and/or packaging, subject to the availability of technically, environmentally and economically sound alternatives. Suppliers are strongly advised to investigate suitable alternative solutions.

Substance(s) phased-out from this product

Comment



13 (19)

4.3.2 Product end-of-life

Nokia Siemens Networks hereby supplies information supporting environmentally sound, safe and economical End-of-Life (EoL) handling/recycling of the product defined on the front page of this document. All disassembly, treatment, recovery and other work must be managed and performed with professional diligence and skill, according to good operating practices and the applicable legal safety, health and environmental requirements and standards, taking into account all relevant health and safety aspects.

4.3.3 Main material fractions

The main fractions of the Product are listed in the table below. This table is not inclusive and the product may contain other materials, substances, components or parts than those identified in this document.

Fraction / material

Amount (g) % Of total weight

Comments

Steel

Stainless steel 18698 49.99 %

Aluminum alloys 2345 6.3 %

Copper alloys 17.3 0.05 %

Polymeric materials

248.1 0.66 %

Mixed electronics (including PWB and standard components)

16094 43 %

Total Weight 37403 100 %

4.3.4 Components and substances which may require special handling in the end-of-life phase

Based on Nokia Siemens Networks sole consideration, the recycling service providers shall at least take into consideration, that such product may include the following materials, substances, components and parts which may require special handling at end-of-life. In addition to the list below product may contain other materials and substances typically used in telecommunication equipment (such as but not limited to lead).



The product contains at least the following materials that may require special handling at end-of-life but this list is non-exhaustive:

Material, component, part

Yes No Application / Location

Polychlorinated biphenyls (PCB) containing capacitors

X

Mercury containing components

X

Batteries X

Printed Circuit Boards (PCB) greater than 10 cm

X

Containing toners in the form of liquid(s), powders(s) or paste(s)

X

Plastics containing brominated flame retardants

X

Asbestos waste and components which contain asbestos

X

Cathode ray tubes

X

Chlorofluorocarbons (CFC), hydrochlorofluorocarbons (HCFC) or hydrofluorocarbons (HFC), hydrocarbons (HC)

X

Gas discharge lamps

X

Liquid crystal displays of a surface greater

X



15 (19)

Material, component, part

Yes No Application / Location

than 100 cm, and all those back-lighted with gas discharge lamps

External electric cables

X E1, STM-1E electrical cable

Components containing refractory ceramic fibres

X

Components containing radioactive substances

X

Electrolyte capacitors containing substances of concern (with a height > 25 mm, a diameter > 25 mm or proportionately similar volume)

X

Beryllium compounds

X

Pressure

X

Liquids X

Gases X

Hidden mechanical springs or other equivalent

X Card latch



4.4 Product recyclability rate

Unit Data

Weight of materials which are (also theoretically) recyclable

Gram 27500

Total weight of the product

Gram 37403

Recyclability rate Percentage (%) 73.5%

4.5 Batteries [optional chapter]

Batteries used in Nokia Siemens Networks products are in conformance with the EU directives 91/157/EEC (hazardous substances) 98/101/EC (amendment) and 93/86/EEC (marking requirements).

Description / relevant information

The product contains battery / accumulator type

manufactured by

NA

The weight and the dimensional characteristics of the battery

NA

4.6 Acoustic noise emission

Description, relevant information

The measurements standards used regarding the acoustic noise

ETS 300 753 Class 3.1

Declared A-Weighted Sound Power Level (LWAd)

6.9 BA(69 dBA)

Declared A-Weighted Sound Pressure Level (Lpam).



17 (19)

4.7 Product delivery packaging

The common materials used for the delivery packaging of the NSN products are listed below.

Packaging Type Material Average Weight (g)

Material recyclability (yes / no)

Unit Package Corrugated board 500 Yes

Delivery container Corrugated Heavy Duty Board

5884 Yes

Cushioning PE-E 895 Yes

Pallet plywood 8900 Yes

Antistatic bag PE 350 Yes

Strap PP 100 Yes

Desiccant Bentonite Clay 125 No

Packaging materials are marked according to

ISO 11469 standard (Plastics generic identification and marking of plastic products)

DIN 6120-1 and DIN 6120-2 standards (Marking of packaging and packaging materials for recycling purposes - Plastics packaging and packaging materials)

GB 18455:2001 (Packaging Recycling Marks, National Standard of the Peoples Republic of China)

The packaging materials comply with the Essential requirements stated in Packaging and Packaging Waste Directive (94/62/EC).

Environment related markings


5 Environment related markings 5.1 EU WEEE marking of separate collection

Product collection and disposal within the European Union

Do not dispose of theproduct as unsortedmunicipal waste. Thecrossed-out wheeled bin means that at the end of the product'slife it must be takento separate collection.

Note: this is applicable onlywithin the European Union(see WEEE Directive 2002/96/EC)

DN0577953

Take-back information


19 (19)

6 Take-back information Nokia Siemens Networks customers can contract with Nokia Siemens Networks for environmentally responsible end-of-life treatment of obsolete equipment. The purpose is to recover the material and energy content of the obsolete products and to ensure safe treatment of substances that can cause harm to people or the environment, if disposed of untreated. In a life-cycle perspective, EoL treatment can compensate for some of the environmental impacts of the earlier stages of the products life cycle.

Nokia Siemens Networks Equipment Take Back Solution provides Nokia Siemens Networks customers with an end-to-end service that includes the removal of end-of-life products from the customers' network and ensures end-of-life treatment in an environmentally responsible way. The Nokia Siemens Networks Equipment Take Back Solution is offered in several modules representing end-to-end work flow of the process:

Removal Collection Recycling Project Management In Nokia Siemens Networks or Other Vendor HW Replacement, that is, SWAP cases Take Back Solution brings in Collection and Recycling Service as Removal and Project Management are already included. The pricing is scalable according to the modules.

If customer chooses not to procure Nokia Siemens Networks Equipment Take Back Solution from Nokia Siemens Networks, customer agrees to dispose of any such equipment in a sound environmental manner, in compliance with all applicable laws.

Statements of complianceContentsSummary of changes1 Introduction2 Product description3 Company environmental information3.1 Nokia Siemens Networks environmental policy3.2 Life cycle thinking3.3 Environmental Management System3.4 Design for Environment

4 Product environmental information4.1 Product energy consumption4.2 Product CO2 footprint4.3 Materials4.3.1 Nokia Siemens Networks Substance List4.3.2 Product end-of-life4.3.3 Main material fractions4.3.4 Components and substances which may require special handling in the end-of-life phase

4.4 Product recyclability rate4.5 Batteries [optional chapter]4.6 Acoustic noise emission4.7 Product delivery packaging

5 Environment related markings5.1 EU WEEE marking of separate collection

6 Take-back information

hit_7065_epd

Documents

Transcript of hit_7065_epd