HINDUSTAN PREFAB LIMITED reinforcement for RCC work including straightening, cutting,bending,placing...

Sl. No Description Units Qty Rate Amount

A CIVIL WORKS

EARTH WORKS

1

Clearing grass and removal of the rubbish upto a

distance of 50 m outside the periphery of the area

cleared.100 m

2 5000.00

2

Earth work in excavation by mechanical means

(Hydraulic Excavator )/ manual means in

foundation trenches or drains (not exceeding 1.5

m in width or 10 sum on plan) including dressing

of sides and ramming of bottoms, lift upto 1.5 m,

including getting out the excavated soil and

disposal of surplus excavated soil as directed,

within a lead of 50 m.

a All kinds of soil. Cum 200.00

3

Filling available excavated earth (excluding rock)

in trenches, plinth, sides of foundations etc. in

layers not exceeding 20cm in depth, Cum 200.00

HINDUSTAN PREFAB LIMITED

THYCAUD, TRIVANDRUM

Name of work : Proposed Interim Building for Malayalam University at Govt. College

campus, Tirur, Malappuram District

BOQ

3 layers not exceeding 20cm in depth,

consolidating each deposited layer by ramming

and watering, lead up to 50 m and lift upto 1.5 m.

Cum 200.00

4Supplying chemical emulsion in sealed

containers including delivery as specified.

aChlorpyriphos/ Lindane emulsifiable concentrate

of 20%Litre 510.00

5

Diluting and injecting chemical emulsion for

POST-CONSTRUCTIONAL anti-termite

treatment (excluding the cost of chemical

emulsion) :

a

Along the external wall below concrete or

masonry apron using chemical emulsion @ 2.25

litres per linear metre including drilling and

plugging holes etc.

(i)With Chlorpyriphos/ Lindane E.C. 20% with 1%

concentration.RM 150.00

b

Treatment of soil under existing floors using

chemical emulsion @ one litre per hole, 300 mm

apart including drilling 12 mm diameter holes

and plugging with cement mortar 1 :2 (1 cement :

2 Coarse sand) to match the existing floor :

(ii)With Chlorpyriphos/ Lindane E.C. 20% with 1%

concentration.Sqm 890.00

Malayalam University of 26 Estimate


CONCRETE WORKS

6

Providing and laying in position cement concrete

of specified grade excluding the cost of centring

and shuttering - All work upto plinth level :

a1:4:8 (1 Cement : 4 coarse sand : 8 graded stone

aggregate 40 mm nominal size).Cum 140.00

REINFORCED CEMENT CONCRETE

7

Providing and laying in position specified grade

of reinforced cement concrete excluding the cost

of centring, shuttering, finishing and

reinforcement - All work upto plinth level :

a1:1.5:3 ( 1 cement : 1.5 coarse sand : 3 graded

stone aggregate 20mm nominal size )Cum 24.00

8

Reinforced cement concrete work in walls (any

thickness), including attached pilasters,

buttresses, plinth and string courses, fillets,

columns, pillars, piers, abutments, post and struts

etc., upto floor five level excluding cost of

centering, shuttering, finishing and

reinforcement.

a1:1.5:3 ( 1 cement : 1.5 coarse sand : 3 graded

stone aggregate 20mm nominal size )Cum 39.00

stone aggregate 20mm nominal size )

FORM WORK

9Centering and shuttering including strutting,

propping etc. and removal of form for :

aLintels, beams, plinth beams, girders, bressumers

and cantilevers.Sqm 650.00

10

Steel reinforcement for RCC work including

straightening, cutting,bending,placing in position

and binding all complete upto Plinth level

Thermo-Mechanically Treated bars Kg 960.00

11

Steel reinforcement for RCC work including

straightening, cutting,bending,placing in position

and binding all complete above Plinth level

Thermo-Mechanically Treated bars Kg 2400.00

12

Random rubble masonry with hard stone in

foundation and plinth including levelling up with

cement concrete 1:6:12 (1 cement : 6 coarse sand

: 12 graded stone aggregate 20mm nominal size)

at plinth level with :

a Cement mortar 1:6 (1 cement : 6 coarse sand) Cum 250.00



MARBLE & GRANITE WORK

13

Providing and fixing 18mm thick gang saw cut

mirror polished (premoulded and prepolished)

machine cut for kitchen platforms, vanity

counters ,window sills , facias and similar

locations of required size of approved shade,

colour and texture laid over 20mm thick base

cement mortar 1:4 (1 cement : 4 coarse sand)

with joints treated with white cement, mixed with

matching pigment, epoxy touch ups, including

rubbing, curing moulding and polishing to edge

to give high gloss finish etc. complete at all

levels.a Granite of any colour and shade

(i) Area of slab over 0.50 sum. Sqm 5.00

14

Providing edge moulding to 18mm thick marble

stone counters, Vanities etc. including machine

polishing to edge to give high gloss finish etc.

complete as per design approved by Engineer-in-

Charge.a Granite work. RM 8.00

WOOD & PVC WORKS

Providing wood work in frames of doors,

15

Providing wood work in frames of doors,

windows, clerestory windows and other frames,

wrought framed and fixed in position :

a Second class teak wood Cum 0.12

b Sal wood Cum 0.70

16

Providing and fixing panelled or panelled and

glazed shutters for doors, windows and clerestory

windows including ISI marked black enamelled

M.S pressed butt hinges bright finished of

required size with necessary screws excluding,

panelling which will be paid for separately.all

complete as per direction Engineer -in -charge

a Second class teak wood

b 35 mm thick shutters Sqm 5.00

17

Providing and fixing ISI marked flush door

shutters conforming to IS: 2202 (Part I)

decorative type, core of block board construction

with frame of 1st class hard wood and well

matched teak 3 ply veneering with vertical grains

or cross bands and face veneers on both faces of

shutters.

a35 mm thick including ISI marked Stainless Steel

butt hinges with necessary screws.Sqm 38.00



18

Providing and fixing factory made P.V.C. door

frame of size 50x47mm with a wall thickness of

5mm, made out of extruded 5mm rigid PVC

foam sheet mitred at corners and joined with 2

Nos. of 150mm long brackets of 15x15mm M.S.

square tube, the vertical door profiles to be

reinforced with 19x19mm M.S. square tube of 19

gauge, EPDM rubber gasket weather seal to be

provided through out the frame. The door frame

to be fixed to the wall using M.S. screws of

65/100mm size complete as per manufacturers

specification and direction of Engineer-in-

Charge.

RM 60.00

Providing and fixing factory made panel PVC

door shutter consisting of frame made out of

M.S. tubes of 19 gauge thickness and size of

19mm x 19mm for styles and 15x15mm for top

& bottom rails. M.S. frame shall have a coat of

steel primers of approved make and manufacture

. M.S. frame covered with 5mm thick heat

moulded PVC 'C' channel of size 30mm

thickness, 70mm width out of which 50mm shall

be flat and 20mm shall be tapered in 45degree

19

be flat and 20mm shall be tapered in 45degree

angle on either side forming styles; and 5mm

thick, 95mm wide PVC sheet out of which 75mm

shall be flat and 20mm shall be tapered in 45

degree on the inner side to form top and bottom

rail and 115mm wide PVC sheet out of which

75mm shall be flat and 20mm shall be tapered on

both sides to form lock rail. Top, bottom and lock

rails shall be provided either side of the panel.

10mm (5mm x 2 ) thick, 20mm wide cross PVC

sheet be provided as gap insert for top rail &

bottom rail. paneling of 5mm thick both side

PVC sheet to be fitted in the M.S. frame welded/

sealed to the styles & rails with 7mm

(5mm+2mm) thick x 15mm wide PVC sheet

beading on inner side, and joined together with

solvent cement adhesive. An additional 5mm a 30mm thick plain PVC door shutters Sqm 19.00

20

Providing and fixing IS : 12817 marked stainless

steel butt hinges (heavy weight) with stainless

steel screws etc. complete :

a 125x64x2.50 mm Each 72.00



21

Providing and fixing aluminium tower bolts ISI

marked anodised (anodic coating not less than

grade AC 10 as per IS : 1868 ) transparent or

dyed to required colour or shade with necessary

screws etc. complete :

a 300x10 mm Each 18.00

b 200x10 mm Each 18.00

22

Providing and fixing aluminium handles ISI

marked anodised (anodic coating not less than

grade AC 10 as per IS : 1868) transparent or dyed

to required colour or shade with necessary screws

etc. complete :

a 125 mm Each 18.00

23

Providing and fixing aluminium hanging floor

door stopper ISI marked anodised (anodic

coating not less than grade AC 10 as per IS :

1868) transparent or dyed to required colour and

shade with necessary screws etc. complete.

a Twin rubber stopper Each 18.00

24Providing and fixing bright finished brass butt

hinges with necessary screws etc. complete :24 hinges with necessary screws etc. complete :

a 125x85x5.5 mm (heavy type) Each 8.00

25

Providing and fixing bright finished brass tower

bolts (barrel type) with necessary screws etc.

complete :a 250x10 mm Each 2.00

b 200x10 mm Each 2.00

26Providing and fixing bright finished brass

handles with screws etc. complete :

a 125 mm Each 2.00

27

Providing and fixing bright finished brass

hanging type floor door stopper with necessary

screws, etc. complete.Each 2.00

28

Providing and fixing IS : 3564 marked

aluminium extruded section body tubular type

universal hydraulic door closer with double speed

adjustment with necessary accessories and screws

etc. complete.

Each 1.00

STEEL WORK



29

Steel work in built up tubular ( round, square or

rectangular hollow tubes etc.) trusses etc.,

including cutting, hoisting, fixing in position and

applying a priming coat of approved steel primer

including welding and bolted with special shaped

washers etc., complete.

a Hot finished welded type tubes Kg 20000.00

FLOORING

30

Chequerred precast cement concrete tiles 22 mm

thick in footpath & courtyard jointed with neat

cement slurry mixed with pigment to match the

shade of tiles including rubbing and cleaning etc.

complete on 20 mm thick bed of cement mortar

1:4 (1 cement: 4 coarse sand).

aMedium shade using 50% white cement 50%

Grey cement.Sqm 360.00

31

Providing and fixing Ist quality ceramic glazed

wall tiles conforming to IS : 15622 (thickness to

be specified by the manufacture ) of approved

make in all colours, shades except burgundy,

bottle green, black of any size as approved by

Engineer-in-Charge in skirting, risers of steps and Sqm 170.0031 Engineer-in-Charge in skirting, risers of steps and

dados over 12 mm thick bed of cement Mortar

1:3 (1 cement : 3 coarse sand) and jointing with

grey cement slurry @ 3.3kg per sum including

pointing in white cement mixed with pigment of

matching shade complete.

Sqm 170.00

32

Providing and laying Ceramic glazed floor tiles

300x300 mm (thickness to be specified by the

manufacturer) of 1st quality conforming to IS :

15622 of approved make in colours such as

White, Ivory, Grey, Fume Red Brown, laid on 20

mm thick Cement Mortar 1:4 (1 Cement : 4

Coarse sand) including pointing the joints with

white cement and matching pigment etc.,

complete.

Sqm 55.00

33

Providing and laying polished vitrified floor tiles

in different sizes (thickness to be specified by the

manufacturer) with water absorption's less than

0.08% and conforming to IS : 15622 of approved

make in all colours and shades, laid on 20mm

thick cement mortar 1:4 (1 cement : 4 coarse

sand) including grouting the joints with white

cement and matching pigments etc., complete.

a Size of Tile 600x600 cm Sqm 850.00



FINISHING

34 12 mm cement plaster of mix :

a 1:6 (1 cement : 6 fine sand) Sqm 1900.00

35 20 mm cement plaster of mix :

a 1:6 (1 cement : 6 coarse sand) Sqm 600.00

INTERIOR FINISHING

36 White washing with lime to give an even shade:

a New work ( One coat) Sqm 2500.00

37

Distempering with oil bound washable distemper

of approved brand and manufacture to give an

even shade

aNew work (two or more coats) over and

including priming coat with cement primer.Sqm 1900.00

EXTERIOR FINISHING

38

Finishing walls with Premium Acrylic Smooth

exterior paint with Silicone additives of required

shade

a

New work (Two or more coats applied @ 1.43

ltr/ 10 sum. over and including base coat of water

proofing cement paint applied @ 2.20 kg/ 10

sum).

Sqm 600.00

sum).

39Painting with synthetic enamel paint of approved

brand and manufacture to give an even shade :

a Two or more coats on new work Sqm 105.00

40Painting with Aluminium paint of approved

brand and manufacture to given even shade.

a Two or more coats on new work Sqm 1450.00

41Polishing on wood work with ready mixed wax

polish of approved brand and manufacture :

a New work Sqm 13.00

ALUMINIUM WORK



42

Providing and fixing aluminium work for doors,

windows, ventilators and partitions with extruded

built up standard tubular sections/ appropriate Z

sections and other sections of approved make

conforming to IS: 733 and IS : 1285, fixed with

rawl plugs and screws or with fixing clips, or

with expansion hold fasteners including

necessary filling up of gaps at junctions, at top,

bottom and sides with required PVC/neoprene

felt etc. Aluminium sections shall be smooth, rust

free, straight, mitred and jointed mechanically

wherever required including cleat angle,

Aluminium snap beading for glazing / panelling,

C.P. brass / stainless steel screws, all complete as

per architectural drawings and the directions of

Engineer-in-charge. (Glazing and panelling to be

paid for separately) :a For fixed portion.

(i)

Anodised aluminium (anodised transparent or

dyed to required shade according to IS: 1868,

Minimum anodic coating of grade AC 15)

Kg 774.00

43

For shutters of doors, windows & ventilators

including providing and fixing hinges/ pivots and

making provision for fixing of fittings wherever

required including the cost of PVC / neoprene43

required including the cost of PVC / neoprene

gasket required (Fittings shall be paid for

separately).

a

Anodised aluminium (anodised transparent or

dyed to required shade according to IS: 1868,

Minimum anodic coating of grade AC 15)Kg 570.00

44

Providing and fixing glazing in aluminium door,

window, ventilator shutters and partitions etc.

with PVC/ neoprene gasket etc. complete as per

the architectural drawings and the directions of

engineer-in-charge . (Cost of aluminium snap

beading shall be paid in basic item) :

a With float glass panes of 4.0 mm thickness Sqm 105.00

NON SCHEDULE ITEMS

45Supplying and filling Available excavated earth

from outside , cosolidating etc completeCum 400.00

46 Aluminium grills for windows of Standard design Sqm 105.00

47

Solid block masonry in superstructure above

plinth level upto floor five level using concrete

block of size 40 x 20 x 15 cm / 40 x 20 x 10 cm

including cost and conveyance of all materials

and labour charges etc.complete.



a In Cement mortar 1:6 Cum 210.00

48

Providing and fixing at all height false ceiling of

3mm P.V.C rigid form sheet manufactured by

M/s Rajasree or equivalent including providing

and fixing of frame work made of special

sections power pressed from MS sheet and

galvanised in accordence with zinc coating 350

as per IS 277 and consisting of angle cleats of

size 25mm wide x 1.6mm thick with flanges of

22mm and 37mm at 600mm centre to centre one

flange fixed to the ceiling with dash fastner

12.5mm dia x 40mm long with 6mm dia bolts to

the angle hanger of 25 x 25 x 0.55mm of required

length, and other end of angle hanger being fixed

with nut and bolts to GI channels 45 x 15 x

0.9mm running at the rate of 600mm centre to

centre to reach the ceiling section 0.5mm thick

button wedge of 80mm with tapered shall be

fixed in a directio perpendicular to GI channel

with connecting clips made out of 2.6mm dia x

330mm long GI wire at every junction including

fixing the PVC rigid form sheet with coiling

section and perimetre channels 0.5mm thick

27mm high having& rails with 7mm

Sqm 890.00

27mm high having& rails with 7mm

(5mm+2mm) thick x 15mm wide PVC sheet

beading on inner side, and joined together with

solvent cement adhesive. An additional 5mm

49

Providing and fixing Structural frame work with

65mm GI pipe verticaly and horizontaly and top

with PVC sheet 18mm thick to seat the PVC

water tank (3000 litre capacity)with concrete

pedestal for bottom support( PVC tank and base

Concrete shall be paid separatly)

Kg 500.00

50Providing 100mm dia bore well with casing pipe,

boaring,casing, testing etc completeMetre 80.00

51

Supplying and fixing 2HP Submersible pump set

with pipes and all other plumbing & electrical

accessories etc complete

Each 1.00

52 Brass Aldrop 300mm for entrance door Each 2.00

53 Stainless steel Aldrop 300mm for internal doors Each 18.00

54Supplying and providing Precast RCC Decorative

Pillar 230mm dia and 2m height.Each 16.00

55Providing and fixing Precast concrete Eve board

150mm depth and 25mm thickRM 200.00



56Providing and fixing precast concrete Ornamental

border 50mm RM 15.00

57

Providing Roofing with Galvanium sheet

0.50mm thick, 550Mpa, AEZ150gm/Sqm

including all fittings and fixtures , scaffolding

etc. complete

Sqm 1200.00

58

Providing Ridge for the roofing using Galvanium

sheet 0.50mm thick including fixtures, fittings ,

scaffolding etc. complete.RM 170.00

TOTAL CIVIL WORKS

B SANITARY AND PLUMBING WORKS

SUB HEAD VIII: SANITARY AND CP

FITTINGS

59

Providing and Fixing White Vitreous China

Pedestal type Water Closet (European Type) with

seat and lid 10 litre low level White vitreous

China Flushing Cistern & C.P.flush bend with

fittings & C.I.Brackets, 40mm flush bend,

Overflow arrangement with specials of standard

makes and mosquito proof coupling of approvedmakes and mosquito proof coupling of approved

municipal design complete including painting of

fittings and brackets, cutting and making good

the walls and floors wherever required with WC

Pan with ISI marked Black Solid plastic seat and

lid

aW.C. Pan with ISI marked Black Solid plastic

seat and lid Each 6.00

60

Providing and fixing water closet squatting pan

(Indian type W.C. pan ) with 100mm sand cast

Iron P or S trap, 10 litre low level white P.V.C.

flushing cistern including flush pipe with

manually controlled device (handle lever)

conforming to IS : 7231, with all fittings and

fixtures complete including cutting and making a

White Vitreous china Orissa pattern W.C. pan of

size 580x440mm with integral type foot rests.Each 6.00

61

Providing and fixing Wash Basin with

C.I.Brackets, 15mm C.P.Brass Pillar Taps, 32mm

C.P.Brass Waste of standard pattern, including

painting of fittings and Brackets, cutting and

making good the walls wherever required

aWhite Vitreous china wash basin size: 630 x 450

mm with a single 15 mm CP brass Pillar Tap Each 11.00



62

Providing and fixing Mirror of Superior Glass of

approved quality and of required shape and size

with plastic moulded frame of approved make

and shade with 6mm thick hard board backing:

a Rectangular shape 453 x 357mm Each 8.00

63

Providing and fixing PTMT Waste Coupling for

Wash Basin and Sink, of approved quality and

colour

aWaste Coupling 38mm of 83mm length and

77mm breadth, weighing not less than 60gms.Each 24.00

64Providing and fixing PTMT Bottle Trap for

Wash Basin and Sink

a

Bottle Trap 38mm single piece moulded with

height of 270mm, effective length of tail pipe

260mm from the centre of the Waste Coupling

77mm breadth with 25mm minimum water seal,

weighing not less than 263gms.

Each 12.00

65

Providing and fixing PTMT Towel rail complete

with brackets fix to wooden slits with cp brass

screws with concealed fittings arrangement of

approved quality and colour approved quality and colour

a

450mm long towel rail with total length of

495mm, 78mm wide and effective height of

88mm, weighing not less than 170gms.

Each 6.00

SUB HEAD IX WATER SUPPLY

COLD WATER SUPPLY PIPING

66

Providing and fixing 3 layer PP-R (Poly

propylane Random copolymer ) pipes SDR 7.4

UV stabilized

a 20mm Dia PP-R, PN16 Pipe for Water supply

Supply, installation & commissioning Metre 120.00

b 25mm Dia PP-R, PN16 Pipe for Water supply


Labour / Installation / Erection:

c 32mm Dia PP-R, PN16 Pipe for Water supply



d 40mm Dia PP-R, PN16 Pipe for Water supply



e 50mm Dia PP-R, PN16 Pipe for Water supply





67

Supply, Leading to site and Installing at position

PPR Ball Valves PN20 Wafer type using Male

Threaded Adapters (MTA) necessary PVC

flanges, gaskets, nuts and bolts complete as

required

a 50mm Dia

Supply, installation & commissioning Each 1.00


68

Providing and placing on terrace (at all floor

levels) polyethylene water storage tank ISI :

12701 marked with cover and suitable locking

arrangement and making necessary holes for

inlet, outlet and overflow pipes but without

fittings and the base support for tank

Per litre 3000.00

69

Providing and fixing CP brass bib cock of

approved quality conforming to IS standards and

weighing not less than 690 gms,

a 15 mm nominal bore Each 12.00

70

Providing and fixing CP brass long body bib

cock of approved quality conforming to IS

standards and weighing not less than 690 gms,

a 15mm nominal bore Each 4.00

71

Providing and fixing CP Brass Angle valve for

basin mixer and gyser points of approved quality

conforming to IS:8931,

a 15mm nominal bore Each 24.00

SOIL, WASTE AND RAIN WATER PIPING

72Providing and fixing PTMT grating of approved

quality and colour

a Rectanular type with openable circular lid

(i)150mm nominal size square 100mm diameter of

the inner hinged round gratingEach 20.00

73

Providing and fixing PTMT soap dish holder

having length of 138 mm breadth 102 mm heigh

of 75 mm with concealed fittings arrangements

weighing not less than 106 gms

Each 6.00

DRAINAGE

EXTERNAL TRENCHES, MANHOLES &

TRAPS



74

Construction of Brick Masonry Manhole in

cement mortor 1:4 (1 cement :4 coarse sand

)R.C.C, top slab with 1:2:4 mix (1 cement : 2

coarse sand :4 graded stone aggregate 20mm

nominal size),foundation concrete 1:4:8 mix(1

cement :4 coarse sand : 8 graded stone aggregate

40mm nominal size )inside plastering 12mm

thick with cement mortor 1:3 (1 cement :3 coarse

sand) finished with floating coat of neat cement

and making channels in cement concrete 1:2:4 (1

cement :2 coarse sand :4 graded stone aggregate

20mm nominal size) finished with a floating coat

of neat cement complete as per standard design:

a

Inside size 90x80 cm and 45 cm deep including

C.I. cover with frame (light duty ) 455x610 mm

internal dimensions total weight of cover and

frame to be not less than 38 Kg ( weight of cover

23Kg and weight of frame 15Kg):

(i)With common burnt clayF.P.S.(non modular)

bricks with class designation 7.5Each 6.00

75

Inside size 120x90 cm and 90 cm deep

incluuding C.I. cover with frame ( medium duty)

500 mm internal diameter, total weight of cover75 500 mm internal diameter, total weight of cover

and frame to be not less than 116 Kg (weight of

cover 58 Kg and weight of frame 58Kg)

aWith common burnt clayF.P.S.(non modular)


76

Supplying and fixing C.I cover 300x300mm

without frame for gully trap ( standard pattern)

the weight of cover to be not less than 4.5 Kg.

Each 8.00

a

Making soak pit 2.5 m diameter 3.0 metre deep

with 45 x 45 cm dry brick honey comb shaft with

bricks of class designation 75 and S.W. drain

pipe 100 mm diameter, 1.8 m long complete as

per standard design.

(i)With common burnt clayF.P.S.(non modular)


NON SCHEDULE ITEM

77

Providing, Fixing, Testing and commissioning at

site ablution Health Spray Faucet, C.P.Flexible

Hose 750mm long nozzle tube, tube holder

etc.complete in all respects

Each 6.00



78

Supply, Installation, testing & commissioning of

Supreme PVC pasted pipe 6kg using Solvent

Cement ISI Marked ] with Heavy duty ISI

Marked PVC fittings, Tees, Elbows, Bends, 'Y's

etc. Adapters, Air vents, Clamping with GI

UClamps as required for firmly install

a 50mm OD 6KG/Sq.cm internal Waste Piping



b 75mm OD 6KG/Sq.cm internal Waste Piping



c 110mm OD 6KG/Sq.cm internal Soil Piping



d110mm OD 6KG/Sq.cm External Soil & Waste

Piping



e160mm OD 6KG/Sq.cm External Soil & Waste

Piping



f 75mm OD 6KG/Sq.cm internal Vent Piping

Supply, installation & commissioning Metre 12.00Supply, installation & commissioning Metre 12.00


79Multi Inlet 110MM X 63MM X 50MM Diameter

150MM Depth.

Supply, installation & commissioning Each 18.00


80

Supplying and fixing Precast RCC septic tank

with soak pit including the cost of earthwork

excavation, filling, testing and commissioning

etc.a 80 usage capacity Each 2.00

TOTAL SANITARY & PLUMBING WORKS

C ELECTRICAL WORK

Wiring

81

Point wiring in P.V.C conduit, with modular

type switch: Wiring for light points/ fan point/

exhaust fan point/ call bell point with 1.5sq.mm

FR P.V.C insulated copper conductor single core

cable in surface /recessed P.V.C conduit with

modular switch, modular plate, suitable G.I box

and earthing the point with 1.5 sq mm FR PVC

insulated copper conductor single core cable etc.

as required.

a Group C Point 270.00



82

Twin Control point wiring in P.V.C conduit,

with modular type switch: Twin control point

wiring in PVC condult , with modular type

switch Wiring for twin control light points with

1.5 sq mm FR PVC insulated copper conductor

single core cable in surface/recessed PVC

condult 2 way modular switch,modular plate.

Suitable G.I box and earthing the point with 1.5

sq mm FR PVC insulated copper conductor

single core cable etc.

Point 1.00

83

Wiring in existing PVC conduit: Supply and

drawing following size of FR PVC insulated

copper conductor, single core cable in the

existing surface/ recessed PVC conduit as

required.

a 2 x 1.5 sq mm + 1 x 1.5 sq mm earth wire Metre 200.00

b 2 x 2.5 sq mm + 1 x 2.5 sq mm earth wire Metre 1200.00

c 2 x 4 sq mm + 1 x 4 sq mm earth wire Metre 250.00

d 2 x 6 sq mm + 1 x 6 sq mm earth wire Metre 50.00

e 4 x 4 sq mm + 2 x 4 sq. mm earth wire Metre 20.00e 4 x 4 sq mm + 2 x 4 sq. mm earth wire Metre 20.00

84

Telephone wiring in existing conduit;

Supply and laying 2 pair, 0.5 sq.mm FR PVC

insulated copper conductor, unarmoured

telephone cable in the existing surface/ recessed

steel/ PVC conduit as required.

Metre 220.00

85

TV Cable in existing conduit; Supply and

drawing co-axial TV cable RG-6 grade, 0.7 mm

solid copper conductor PE insulated, shielded

with fine tinned copper braid and protected with

PVC sheath in the existing surface/ recessed

steel/ PVC conduit as required.

Metre 50.00

86

S/F PVC Conduit: Supplying and fixing of

PVC conduit with accessories in surface/ recess

including cutting the wall and making good the

same in case of recessed conduit as required.

a 20 mm Metre 1000.00

b 25mm Metre 200.00

Switches & accessories



87

S/F modular type switch/ socket : Supplying

and fixing following modular switch/socket on

the existing modular plate & switch box

including connections but excluding modular

plate etc as required.

a 3 pin 5 / 6 amps socket outlet Each 5.00

b Telephone socket outlet Each 8.00

c TV antenna Socket outlet Each 2.00

88

S/F modular type electronic fan regulator :

Supplying and fixing stepped type (5 step)

electronic fan regulator on the existing modular

plate and switch box excluding modular plate but

including connectors etc as required.

Each 55.00

89

S/F modular type blanking plates : Supplying

and fixing modular blanking plate on the existing

modular plate & switch box excluding modular

plate as required.

Each 30.00

90

S/F modular boxes, base & cover plate :

Supplying and fixing following size/ modules, GI90 box along with modular base cover plate for

modular switches in recess etc as required.

a 1 or 2 module (75mmx75mm) Each 45.00

91

S/F light plug point with modular type

accessories: Supplying and fixing suitable

size G.I box with modular plate and cover in

front on surface or in recess, including providing

and fixing 3 pin 5/6 amps modular socket outlet

and 5/6 amps modular switch, connection,

painting, testing etc. as required.

Each 30.00

92

S/F Power plug point with modular type

accessories: Supplying and fixing suitable

size G.I box modular plate and cover in front or

on surface or in recess,including providing and

fixing 6 pin 15/16& 5/6 amps modular socket

outlet and 15/16 amps modular

switch,connection,painting etc.as required.

Each 7.00

93

S/F ceiling rose: Supplying and fixing 3 pin ,

5 amps ceiling rose on the existing junction box/

wooden block including connection etc as

required.

Each 20.00



94

S/F Decorative Brass holder: Supplying and

fixing brass angle batten holder with decorative

UPVC covering with copper links on the existing

junction box/ wooden block including

connection, testing etc as required.

Each 12.00

95

Erection of wall bracket/ ceiling fittings:

Erection, testing and commissioning of wall

bracket/ ceiling fittings of all size and shapes

containing upto two GLS lamps per fittings,

complete with all accessories etc. as required.

Each 8.00

96

S/F call bell/ buzzer: Supplying and fixing

call bell/ buzzer suitable for DC/ AC single

phase, 230 volts, complete as required.Each

2.00

97

ITC fluorescent fitting directly on Celing :

Installation testing and commissioning of pre

wired, fluorescent fitting/ compact fluorescent

fitting of all types, complete with all accessories

and tube etc. directly on ceilling/ wall, including

connection with 0.5 sq.mm PVC insulated, PVC

sheathed three core flexible cu cable, earthing,

testing etc. as required.

Each 145.00

98

ITC fluorescent fitting with down rods :

Installation testing and commissioning of pre

wired, fluorescent fitting/ compact fluorescent

fitting of all types, complete with all accessories

and tube etc, including supplying and fixing ball

and socket arrangements, 2 no.down rods of

20mm dia x 1.6mm thick steel conduit upto 30

cm length, painting and wiring the down rods and

connection with 1.5 sq.mm FR PVC insulated,

copper conductor, single core cable/ 0.5 sq.mm

PVC insulated, PVC sheathed three core flexible

cu cable, earthing, testing etc. as required.

Each 2.00

99

S/F Extra down rods for FTL fittings:

Providing and fixing extra conduit down rod of

20mm dia, 2 x 10 cm length wiring with 1.5

sq.mm FR PVC insulated, copper conductor,

single core cable/ 0.5 sq.mm PVC insulated,

PVC sheathed three core flexible cu cable,

including painting etc. as required. (Note : More

than 5cm length shall be rounded to the nearest

10cm and 5 cm or less shall be ignored).

Each 2.00



100

ITC ceiling fan : Installation, testing and

commissioning of ceilling fan, including wiring

the down rods of standard length (up to 30 cm)

with 1.5 sq mm FR PVC insulated, copper

conductor single core cable/ 0.5 sq.mm PVC

insulated, PVC sheathed three core flexible cu

cable, etc. as required.

Each 55.00

101

S/F Extra down rod for ceiling fan: Supplying

and fixing extra down rod of 10 cm length G.I.

Pipe 20 mm dia, heavy gauge including painting

etc. as required. (Note :More than 5 cm length

shall be rounded to the nearest 10 cm and 5 cm or

less shall be ignored).

Each 2.00

102

ITC exhaust fan up to 450 mm sweep :

Installation of exhaust fan up to 450 mm sweep

in the existing opening, including, making the

hole to suit the size of the above fan, making

good the damage, connection, testing ,

commissioning etc. as required.

Each 10.00

MCB DISTRIBUTION BOARD

S/F Horizontal TPN Prewired MCB DB :

Supplying and fixing following way, three pole and

103


neutral sheet steel prewired distribution board, 415

volts on surface /recessed complete with tinned

copper busbar, neutral link, earth bar, dinbar,

detachable gland plate, inter connections,

phosphatized and powder painted including earthing

etc as required (but with out MCB/RCCB/Isolator)

a 6 Way (4+18) Double door, horizontal type Each 4.00

104

S/F Vertical TPN MCB DB : Supplying and fixing

following way, three pole and neutral sheet steel

vertical type distribution board, 415 volts on surface

/recessed complete with tinned copper busbar, neutral

link, earth bar, dinbar, detachable gland plate, inter

connections, phosphatized and powder painted

including earthing etc as required (but with out

MCB/RCCB/Isolator)

a 8 Way Double door Each 1.00



105

S/F Vertical TPN prewired MCCB DB :


neutral sheet steel, dust protected, vertical type

distribution board with 200amps busbar, 415 volts on

surface /recessed complete with tinned copper busbar,

neutral link, earth bar, dinbar, detachable gland plate,

inter connections, phosphatized and powder painted

including earthing etc as required (but with out

MCB/RCCB/Isolator)

a 6 Way Double door Each 1.00

106

S/F 'C' Series, MCB : Supplying and fixing 6

amps to 32 amps rating 240/ 415 volts C series

miniature circuit breaker suitable for lighting and

other loads of the following poles in the existing

MCB DB complete with connections testing and

commissioning etc as required.

a Single pole Each 93.00

b Triple pole Each 6.00

c Triple pole and neutral Each 7.00

107

S/F MCB Blanking plate : Supplying and fixing

single pole MCB blanking plate in the existing MCB

DB etc as required.

Each 10.00

108

S/F 4P MCB Isolator : Supplying and fixing the

following rating 4 pole, 415 volts Isolator in the

existing MCB DB complete with connections testing

and commissioning etc as required.

a 40 amps, 4 pole Each 1.00

109

S/F TPN RCCB : Supplying and fixing the

following rating, 415 volts triple pole & neutral

Recidual Current Circuit Breaker (RCCB) having

sensivity current capacity of 100mA in the existing

MCB DB complete with connections testing and

commissioning etc as required.

a 40 amps, 4 pole Each 4.00

110

S/F TPN MCCB : Supplying and fixing the

following rating, 415 volts triple pole & neutral

Moulded Case Circuit Breaker (MCCB) having

breaking capacity of 16kA in the existing MCB DB

complete with connections testing and commissioning

etc as required.

a 100 amps, 4 pole, 16 kA, 0 - 0.8 ln Each 1.00



111

S/F 20 A SPN MCB industrial socket outlet :

Supplying and fixing 20 amps, 240 volts, SPN

industrial type, socket outlet with 2 pole and

earth, metal enclosed plug top along with 20

amps C series SP MCB in sheet steel enclosure

on surface or in recess, with chained metal cover

for the socket out let and complete with

connection, testing and commissioning etc. as

required.

Each 5.00

Earthing

112

Copper earth plate electrode :

Earthing with Copper earth plate of size 600mm

X 600mm X 3mm thick including accessories,

and providing masonary enclosure with cover

plate having locking arrangement and watering

pipe, with charcoal or coke and salt etc. as

required.

Set 2.00

113

GI Pipe Earthing :

Earthing with GI earth pipe 4.5 mtr long, 40mm

dia, including accessories, and providing

masonary enclosure with cover plate having

locking arrangement and watering pipe, with

charcoal or coke and salt etc. as required.

Set 2.00

114

S/F end termination of L.T. XLPE cables :

Supply of all materials and made termination for

the following PVC Insulated Armoured

Aluminium L.T.Cables (AYWY / XLPE) using

single compression type cadmium plated brass

cable glands, Aluminium crimped type cable

lugs, cable identification tags and including gland

earthing using copper conductor of adequate size

AL-CU strip, for termination 'of Cables etc. as

required

a 4C x 16 sq.mm Each 4.00

b 4C x 25 sq.mm Each 6.00

c 3.5C x 50 Sq.mm Each 4.00

115

S/L of L.T. XLPE cables on surface : Laying

and fixing of one number Al XLPE insulated

PVC sheathed armoured power cable of the

following size clamping on the wall using

suitable metal clamps spacing not to exceed 50

cm etc. as required.

a up to 35 sq.mm Metre 186.00

b up to 95 sq.mm Metre 120.00



116

S/F 4 nos 6A plug points with modular type

accessories in combined position:

Supplying and fixing suitable size G.I box

modular plate and cover in front on surface or in

recess, including providing and fixing 4 numbers

2/3 pin combined 5/6 amps modular socket outlet

and 4 umbers 5/6 amps modular switch,

connection, testing etc. as required.

Each 35.00

NON SCHEDULE ITEMS

117

S/F 'C' Series, TP MCB : Supplying and fixing

the following rating 415 volts C series, triple pole

miniature circuit breaker suitable for lighting and

other loads, in the existing MCB DB complete with

connections testing and commissioning etc as

required.

a 40A TP Each 1.00

118

S/F 4P MCB metal enclosure: Supply and

fixing 4 way metal enclosure, on surface / recess,

complete with , earth bar, din bar, detachable

gland plate, inter -connections, phosphatized and

powder painted including earthing etc. as

required.

Each 3.00

119

S/F modular type data socket (RJ45 Cat 6) :

Supplying and fixing of modular type RJ-45 (Cat

6) data socket on the existing modular plate &

switch box including connections but excluding

modular plate etc as required.

Each 27.00

120

Supply of 1x36/40W mirror optic FTL : Supply

of 1 x 36 / 40 watt surface/ recessed mounting

type Flourescent tube lamp (FTL) mirror optic

luminaire with white powder coated CRCA sheet

steel housing & aluminium mirror reflector,

complete with all accessories and one number

36/40 watts tube etc. as per the direction of

engineer in charge as required.

Each 68.00

121

Supply of 2x36/40W mirror optic FTL : Supply

of 2 x 36 / 40 watt surface/ recessed mounting

type Flourescent tube lamp (FTL) mirror optic


steel housing & aluminium mirror reflector,

complete with all accessories and two numbers

36/40 watts tube etc. as per the direction of


Each 41.00



122

Supply of 1x36W decorative box type FTL

fittings: Supply of 1 x 36 watts box type

flourescent tube lamp (FTL) with precoated

CRCA sheet steel housing wired with

commercial HF ballast, decorative end caps,

complete with all accessories and one number 36

watts tube etc. as per the direction of engineer in

charge as required.

Each 2.00

123

Supply of 2x36W mirror optic CFL fittings :

Supply of 2 x 36 watts recessed mounting type

Compact Flourescent Lamp (CFL) mirror optic


steel housing with aluminium mirror reflector

and swing out mounting bracket, complete with

all accessories and 2 numbers 36 watts 'L' type

CF lamps etc. as per the direction of engineer in

charge as required.

Each 4.00

124

Supply of 2x36W low glare mirror optic CFL

fittings : Supply of 2 x 36 watts recessed

mounting type low glare Compact Flourescent

Lamp (CFL) mirror optic luminaire with powder

coated CRCA sheet steel housing with square

paralite P5 louver block in a perforated metallic

frame complete with all accessories and 2

Each 9.00

frame complete with all accessories and 2

numbers 36 watts 'L' type CF lamps etc. as per

the direction of engineer in charge as required.

125

Supply of 2x11W mirror optic CFL : Supply

of 2 x 11W mirror optic surface/ recess mounting

type compact flourescent lamp (CFL) fittings

with white powder coated CRCA sheet steel

housing, aluminium mirror reflector, including

all accessories and 2 Nos 11watts 'S' type CF

lamps etc. as per the direction of engineer in

charge as required.

Each 22.00

126

Supply of 18W CFL mirror light fittings :

Supply of 18 watts compact flourescent lamp

(CFL) mirror light fittings with white powder

coated CRCA sheet steel housing with opal

acrylic diffuser and decorative end plates,

complete with all accessories and one number

18watts 'L' type CF lamp etc. as per the direction

of engineer in charge as required.

Each 8.00



127

Supply of 18W CFL downlighter (recess) :

Supply of recess mounting type 18 watts compact

flourescent lamp (CFL), horizontal downlighter

fittings with white powder coated CRCA ring

with spun aluminium reflector, centre frosted

glass in ring frame fixed to the housing, wired

with commercial HF ballast, complete with all

accessories and one number 18watts 'D' type CF

lamp etc. as per the direction of engineer in

charge as required.

Each 5.00

128

SITC of 25W candle lamp ranthel light

fittings : Supply of 25 watts candle lamp type

ranthel light fittings, with well painted metalic

body and clear glass shade, complete with all

accessories and one number 25watts candle lamp

etc. as per the direction of engineer in charge as

required.

Each 10.00

129

Supply of 15/18W retrofit CFL : Supply of

15/18 watts retrofite compact flourescent lamp (R-

CFL) for the decorative brass lamp holder, etc. as

per the direction of engineer in charge as

required.

Each 12.00

SITC of 2x36W CFL outdoor fittings :

130

SITC of 2x36W CFL outdoor fittings :

Supply, installation, testing and commissioning

of 2 x 36 watts, CFL lamp fittings of epoxy black

powder coated sheet steel housing, with epoxy

white powder coated CRCA sheet steel gear tray,

clear acrylic cover, aluminium reflector with

complete accessories with two numbers 36W

CFL lamp etc, including supply of suitable size

class- B G. I. pipe (2 m), top of the pipe bend to

required angle and provision for fixing the CFL

lamp fitting, painting with 2 coats of white colour

paint, over a coat of primer, fixing on the wall by

using suitable G.I. clamp and giving connections

using required length of 2.5 sq.mm PVC

insulated and sheathed 3 core round flexible

copper wire, etc. as per the direction of engineer

in charge as required.

Each 18.00

131

Supply of 1200mm Ceiling Fan : Supply of

1200 mm sweep Electric Ceiling Fan, White

Colour, capacitor type with double ball bearing,

shackles, down rod, canopies, blades suitable for

operation on 220/ 240V, 50 Hz, single phase AC

supply conforming to IS - 374 / 1979 class I

(without regulator) high speed, etc. as per

direction of engineer in charge as required.

Each 13.00



132

Supply of 1400mm Ceiling Fan : Supply of

1400 mm sweep Electric Ceiling Fan, White

Colour, capacitor type with double ball bearing,

shackles, down rod, canopies, blades suitable for

operation on 220/ 240V, 50 Hz, single phase AC

supply conforming to IS - 374 / 1979 class I

(without regulator) high speed, etc. as per the

direction of engineer in charge as required.

Each 41.00

133

S/F 400mm Wall Fan with pulling cord :

Supplying and fixing 400 mm sweep wall fan

with 3 speed positions with pulling cord and

giving connections, etc. as per the direction of


Each 5.00

134

Supply of 305mm Exhaust Fan with front

guard : Supply of 305 mm sweep, 1400 rpm

heavy duty exhaust fan with front guard, working

on 230 V AC supply, etc. as per the direction of


Each 10.00

135

Supply of Al XLPE armoured power cable :

Supply of following size heavy duty XLPE

insulated and PVC sheathed armoured power

cable, conductors of best conductivitycable, conductors of best conductivity

aluminium, 1.1 KV grade, conforming to IS 7098

(part-I) etc, as required.

a 4C x 16 sq.mm Metre 75.00

b 4C x 25 sq.mm Metre 110.00

c 3.5C x 50 Sq.mm Metre 120.00

136

S/L of Cat 6 4 pair UTP Ethernet cable :

Supply and laying CAT6 4Pair UTP Ethernet

Cable using PVC Conduits maintaining proper

clearances for the entire route as per

specifications.

Metre 850.00

137

S/F Krone box/ Telephone DB : Supply and

fixing of lockable, syntax or PVC telephone

terminal Box for 2 pair telephone cables, dust

tight and vermin proof. The work should also

include supply of all materials and termination of

two pair telephone wires & incoming Telephone

cable etc. as required.

Each 1.00



138

S/F RJ 45 (Cat 6) Data cable termination Box:

Supply and fixing of 48U powder coated GI

server rack with port switch, spike & necessary

patch codes with lockable acrilyc front door,

including power plugs, termination & testing etc.

as required.

Each 1.00

139

S/F bare Cu wire for loop earth : Supply and

laying one number of the following SWG good

quality bare copper wire on surface for loop

earthing along with existing XLPE insulated

aluminium cable as required.

a 10 SWG Cu Metre 420.00

b 8 SWG Cu Metre 250.00

140

S/L 25mm X 3mm Copper strip on ground :

Supplying and laying 25 mm X 3 mm Copper

strip, as earth conductor, 0.5 mtr below the

ground level, including soldering, jointing

surface must be lead plated and using brass nut &

bolts, etc. as required.

Metre 50.00

SITC of KSEB Meter board : Fabrication,

141

SITC of KSEB Meter board : Fabrication,

supply, Installation, testing & commissioning one

number cubicle type energy meter board made

out of 2mm thick MS sheet, Powder coated,

including provision for fixing KSEB 3phase

energymeter rating above 60A, with CT's,

providing & fixing of 3nos 100A cut out fuses,

3nos 100/5A class1.0, 15VA CT's & control fuse,

phase indication lamps and one number 125A 4P

SDF with HRC and provision for locking the

incoming & Metering section and terminating

3.5x 50.0 sq. mm AL XLPE cable for incoming

and out going side, including CT testing etc, as

required.

Each 1.00

142

SITC of Control panel for 2 hP submersible

pump set: Fabrication, supply, Installation,

testing & commissioning one number control

panel board made out of 2mm thick MS sheet,

well painted over a coat of primer, with suitable

breakers, indicators, push buttons, ammeter,

voltmeter, capacitor, contactors and provision for

Each 1.00



143

SITC of 2TR Split Airconditioner with

stabilizer: Supplying, installation, testing &

commissioning of 2TR split Airconditioners

suitable for single phase, 50Hz, 230 volts, A/C

supply with hermetically sealed compressor with

air cooled condenser, motor capacitor start run,

capacitors relay and over load protector

interconections including all accessories and

remote with special purpose A/C stabilizers, etc

as required.

Each 5.00

MISCELLANEOUS ITEMS.

144

S/F DCP fire extinguisher (5kg) : Supply and

Installation of 5kg Dry Chemical Powder type

(DCP) fire extinguishers having ISI mark along

with mounting supports etc. as required.

Nos 1.00

145

DOCUMENTS & APPROVAL.

Preparation of necessary forms, documents

drawings etc. and procuring approval from

Kerala state Electricity Board. all expenses

except statutory charges shall be met by

Lum 1.00

TOTAL ELECTRICAL WORKSTOTAL ELECTRICAL WORKS


HINDUSTAN PREFAB LIMITED reinforcement for RCC work including straightening, cutting,bending,placing...

Documents

Transcript of HINDUSTAN PREFAB LIMITED reinforcement for RCC work including straightening, cutting,bending,placing...