US and International Patents and Patents Pending.*Above diagram is a representation onlyTO OPERATE:1. To start Press FLOWto ON.2. Dispense when SYSTEM READY is GREEN.3.System ReadySystem ChargingReplace FilterWater/Ozone LowSERVICEFLOWOFF ONCOLD WATER IN OZONE SOLUTION OUTChemical-free cleaner, stain-remover, deodorizerand sanitizer.psi1530456075Press FLOWto OFF when not dispensing. WATER IN TO STABILIZATION MODULE hoseFilter CartridgeOZONE SOLUTION OUThoseFLOWOFF/ON SwitchPerformance IndicatorsEnsure that the water pressure is at minimum 30 PSI (207 kPa) and maximum 65 PSI (488kPa)Service LightQUICK DISCONNECTS1.54.25COLD WATER IN hoseHigh Capacity Unit Stabilization Module(HCU)HCUIG R2.0 08/11INSTALLATION INSTRUCTIONSFor indoor / dry locations only1.Carefully remove all of the items from the cartons.2.Remove mounting hardware from plastic packages.3.Attach HCU to wall using 4 screws in fanges top and bottom. If mounting to drywall, attach to 1/2 plywood backer board to wall before mounting High Capacity unit.4.Align Stabilization Module with High Capacity Unit as shown.5.Mount Stabilization Module bracket to wall with a minimum spacing of 1.5 from the High Capacity Unit.Mount will be 4.25 from the closest HCU mount. Use bracket as template mark holes on wall using a 1/4 drill bit. Place a blue plastic insert in each holes (4) using a hammer.Screw brackets to wall using supplied 8 X 1 1/4 screws. 6.Once brackets are mounted, hang Stabilization Module.7.Attach quick disconnect to COLD WATER IN on Stabilization Module (blue color fttings on left side connection facing unit) 8.Attach connector hose supplied to right side outlet on Stabilization Module attach opposite end to WATER IN on HCU.(white color fttings into grey) 9.Ensure that the water pressure is at minimum 30 PSI (207 kPa) and maximum 65 PSI (488kPa). This can be checked with a simple water pressure testing gauge available at most hardware stores.10.Attach hose without fttings to OZONE SOLUTION OUT on HCU barbed ftting - clamp is not required.11.Connect only to a circuit that is protected by a ground-fault circuit-interrupter (GFCI).NOTE: Unit to be installed vertically as shown in the picture above never horizontally. Doing so will damage the unit.NOTE: The new hose-sets supplied with the appliance are to be used, old hose-sets should not be reused.Chemical-free Cleaning System High Capacity UnitINSTALLATION GUIDEwww.tersanoprofessional.com 1-800-727-8835START-UP INSTRUCTIONS1.Install the High Capacity unit as per INSTALLATION INSTRUCTIONS above.2.Make sure the power cord is plugged into 110v power outlet.3.Ensure COLD WATER IN hose is attached to open faucet or permanent cold water source with a minimum of 30 PSI (207 kPa) , and a maximum 65 PSI (488kPa).4.To start, press FLOW switch to ON position. 5.When SYSTEM READY indicator is GREEN, dispense into mop bucket, auto scrubber, carpet extractor or spray bottle.6.Shut unit of when not in use by pressing FLOW switch to OFF position.7.If you encounter a red light with initial installation you may need to turn the device on and of multiple times as it sets itself.Once set and installed it will charge thereafter. NOTE: If you still get a red light, check that the cold water is turned on. Check that there are no kinks in the line to allow uninterrupted fow of water. Also check that the cartridge is in properly and the protective plastic on the cartridge has been removed.Testing was performed using a dutycycle of 5 minutes on, 25 minutes of, with a maximum 60 minutes per 24 hour periods. Do not exceed this duty cycle.GROUNDING INSTRUCTIONS This appliance must be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a cord having an appliance-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is installed and grounded in accordance with all local codes and ordinances.WARNING: Risk of Electric Shock. Disconnect power before servicing.Never block or restrict OZONE SOLUTION OUT hose with nozzle, clamp or shut-of valve. This may damage unit and will void the warranty. Always use FLOW ON/OFF switch to start or stop fow of Ozone Solution.WARNING: Improper connection of the appliance-grounding conductor can result in a risk of electric shock. Check with a qualifed electrician or service representative if you are in doubt whether the appliance is properly grounded. Do not modify the plug provided with the appliance; if it will not ft the outlet, have a proper outlet installed by a qualifed technician.This appliance is not intended for use by children or those with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safetyHCUIG R2.0 08/11Chemical-free Cleaning System High Capacity UnitSTART-UP GUIDEwww.tersanoprofessional.com 1-800-727-8835US and International Patents and Patents Pending.*Above diagram is a representation onlyTO OPERATE:1. To start Press FLOWto ON.2. Dispense when SYSTEM READY is GREEN.3.System ReadySystem ChargingReplace FilterWater/Ozone LowSERVICEFLOWOFF ONCOLD WATER IN OZONE SOLUTION OUTChemical-free cleaner, stain-remover, deodorizerand sanitizer.psi1530456075Press FLOWto OFF when not dispensing. WATER IN TO STABILIZATION MODULE hoseFilter CartridgeOZONE SOLUTION OUThoseFLOWOFF/ON SwitchPerformance IndicatorsEnsure that the water pressure is at minimum 30 PSI (207 kPa) and maximum 65 PSI (488kPa)Service LightQUICK DISCONNECTS1.54.25COLD WATER IN hoseHigh Capacity Unit Stabilization Module(HCU)