HF Motion Sensor Introduction · DALI Sensors This DALI sensor is designed for built-in lighting...
Transcript of HF Motion Sensor Introduction · DALI Sensors This DALI sensor is designed for built-in lighting...
-
Hytronik Microwave motion sensor 01
Sensors for On-off Control
※ 100 hrs burn-in for fluorescent lamp※ Ambient daylight threshold※ Zero-cross relay operation
HC002S
Flush Mounting Version
HF Motion Sensor IntroductionCompletely built-in the lighting fixture, the motion sensor utilizes Doppler principle and RADAR technology to detect moving objects at certain speed & reflection surface, and gives output control signals to achieve on/off control, 2 steps dimming control, or 3-step dimming control function.
A daylight sensor is also employed to set the threshold at which the motion sensor can be activated.
With DIP switch, it is easy and accurate to select suitable detection area, motion hold-time, daylight threshold, stand-by dimming level, as well as stand-by period to fit for each specific installation.
HC005S※ Zero-cross relay operation※ The smallest sensor with DIP switch※ Loop-in and loop-out, easy wiring
Super-compact Version
page 16
HC009S-KD※ Separate sensor antenna (3 types to choose), no shadow cast in LED bulkhead※ 100 hrs burn-in for fluorescent lamp※ Ambient daylight threshold※ Zero-cross relay operation
HC030S
Attachable Version
For external installation, attach to outside of fixture
※
Detached Version
page 70 page 122
page 107
HC501SInput voltage 12V DC (24V/ 48V can be customized)
DC Operation Version
※
page 88
HC009S ※ 100 hrs burn-in for fluorescent lamp※ Condominium control ※ Ambient daylight threshold※ Zero-cross relay operation
Standard Version
page 19
-
Hytronik Microwave motion sensor 02
Sensors for 3-step Dimming Control (Corridor Function)
※1-10V output control※ Super compact size※ Manual override access※ Ambient daylight threshold※ 100 hrs burn-in for fluorescent lamp
※ 2 or multi sensors control the same group of slaves※ 100 hrs burn-in for fluorescent lamp※ Zero-cross relay operation※ Ambient daylight threshold
HC018V HC019V
Condominium Control VersionAdvanced Version
HC403V-KD
Detached Version
page 22 page 26 page 73
※ With remote control※ Ambient daylight threshold※1-10V output control
DALI Sensors
This DALI sensor is designed for built-in lighting fixture, to be incoporated in the DALI system, taking command from the DALI master, accepting and carry out the grouping work with up to 64 luminaires, switch on/off, or dim the assigned group members, and feed back the status to the DALI master.
HC011D HC407V + HRC-02
Flush Mounting VersionPWM Dimming Control
page 77 page 111
Separate sensor antenna (3 types to choose), no shadow cast in LED bulkhead1-10V output controlAmbient daylight threshold100 hrs burn-in for fluorescent lamp
※
※
※
Work with most ordinary non-dimmable LED driversWorld-wide patented circuitFor both Contant Current (350-1050mA) and Constant Voltage (20-90V) driver.
※ ※ ※
HCD409※ For DALI BUS power supply※ 16 groups selection via rotary switch※ 3-step dimming control
※ For DALI BUS power supply※ 16 groups selection via rotary switch※ 3-step dimming control※ Flush mounting installation
HCD402page 30 page 105
HC017V
Absence Detection
page 91
※ Motion sensor won`t be activated until the push switch is short-pressed.※ 100 hrs burn-in for fluorescent lamp※ Manual override access
※ DALI power supply circuit inluded.※ Manual override access※ 3-step dimming control※ independent DALI system
HCD418 page 33
※
-
※ Condominium control※ 100 hrs burn-in for fluorescent lamp※ Zero-cross relay operation※ Ambient daylight threshold
Sensors with RF Wireless Transmission Control
Integrated Motion Sensor LED Drivers
False Ceiling Sensors
Daylight Harvest
※ On-off function only, with built-in daylight sensor※ Rotary switch grouping before installation, easy to setup※ Manual override access
※ 1-10V dimming control with built-in daylight sensor※ Rotary switch grouping before installation, easy to setup※ Manual override access
RF Transmitter RF Receiver (on-off control) RF Transmitter RF Receiver (dimming)
HC018V/RF HC023RF HC018V/RF HC024RF
Right time, right place and right amount of light!
※ With built-in daylight sensor DS02, interact with daylight, and maintain the Lux level.
On--off Version SensorDIM Version (3-step dimming)
※ Multiple current selections ※ Multiple current selections※ Separate sensor antenna (3 types to choose)Separate sensor antenna (3 types to choose)※
page 61 page 65
page 51
HEC8025 HEC9025page 37 page 41 HC407VDS + HRC-01
page 99
Motion Sensor + Photo Cell + Remote Control
Combination of HF motion sensor and LED power supply.
3-step Dimming Control Condominium Control PWM Dimming Control
HC009S /EXT HC018V/EXT HC019V /EXT HC011D /EXTpage 128 page 136page 125 page 132
On--off Version
RF Transceiver RF Receiver (on-off control) RF Receiver (dimming)
HC028V/RF HC023RF HC024RFpage 45 page 50
※ Serve as both master & slave ※ 3 rotary switches, one for sending RF signal and the other two for receiving RF signals.※ Manual override access※ FSK 868/433/315/915MHz
※ Slave only※ Rotary switch grouping before installation, easy to setup※ FSK 868/433/315/915MHz
※ Slave only※ Rotary switch grouping before installation, easy to setup※ FSK 868/433/315/915MHz
page 114
page 55
※ 100 hrs burn-in for fluorescent lamp※ Condominium control ※ Ambient daylight threshold※ Zero-cross relay operation
※1-10V output control※ Manual override access※ Ambient daylight threshold※ 100 hrs burn-in for fluorescent lamp
※Work with most non-dimmable LED drivers※World-wide patented circuit※For both Contant Current (350-1050mA) and Constant Voltage (20-90V) driver.
-
Reinforced Version Medium Range Sensor
Dry-contact Sensors
※ Ambient daylight threshold※ Loop-in and loop-out
※ Input voltage 12V DC※ Ambient daylight threshold
3-pole relay alternating controlVoltage-free sensor
HC009SDC HC502SDC
Flush Mounting VersionStandard Version
HC020SDC
Alternating Version
page 84 page 120 page 86
HC009S /R HC002S /R HC008S /Mpage 97 /139 page 98※ On/off control.※ Triac dimmer decides the lighting level (1-100%) when motion detected.
Special Applications
Specially designed for T8 LED lamp, ultra compact size for on/off and dimming control.
Converting daylight into 1-10V signal, and the control gear can compensate artificial light automatically according to the preset target Lux value.
This sensor shifts in between two dif ferent loads when movement is detected.
Reinforced sensor for high-bay and warehouse installation. Detection height up to 12m.
Phase-cut power output from the dimmer goes to the sensor first, controlled by the sensor, and then supplied to the luminaires.
For narrow detection, such as toilet compartment.
※ On/off control※ Zero-cross relay operation
※※
※On/off control※Ambient daylight threshold.
Daylight Sensor Built-in Micro-sensor Alternating Version
DS02 HCT8 HC021Spage 100 page 80 page 94
For Triac Dimmer
HC402S /T page 117
Hytronik Microwave motion sensor 04
※ Work with 1-10V control gear ※Dimming function※Ambient daylight threshold
※ For 100,000hrs lighting fixture※ Shifting in between two separate load, 2 steps dimming control function.
-
Typical Lighting Applications:
Features
Zero-cross relay operationDesigned in the software, sensor switches on/off the load right at the zero-cross point, to ensure the min. current passing through the relay contact point, and enable the max. load and life-time of the relay.
Condominium control functionIn many cases, several sensors are connected together to control the same fixture, or to trigger on each other, the sudden on/off of the lamp tube or the ballast/driver causes huge magnetic pulse, which may mis-trigger the sensor. The sensor has a very advanced software to ignore that interference, and keep each individual sensor functioning well.
Wire loop-in and loop-outTo save cost and assembly work, all Hytronik sensors are designed with L and N for power in, and L’ and N for power out to the load. Easy, nice and clean.
Ambient daylight thresholdRapidly turn off/on the fixture 2 cycles within 2 sec, the sensor can set the ambient daylight level as threshold. This feature enables the fixture to function well in any real application circumstance, as the daylight penetrated into fixture may vary a lot.The latest surrounding lux value (either the setting on DIP switch or the learned ambient lux threshold) can overwrites previous lux value learned. The latest action stays in validity.
Product Benefits
Tailor-made for automatic lighting intelligent application.Totally enclosed in fixture, there is no need to keep the sensor head sticking out of the fixture thanks to microwave that can penetrate any non-metal objects.Extremely low transmission power,
-
Installation
1
Others
The sensor relay has a lifespan of 300,000 cycles at the rated max. load. However if the actual load is below the rated max. load, the actual lifespan will be easily prolonged by 2x, 5x, or even 10x ! 1
Always keep the antenna at least 5mm above the metal mounting surface to avoid mis-trigger problem.
2 High metal wall also blocks and reflects microwave. Do not put the sensor deeply in metal wall. Keep the sensor to the openning as close as possible.
Keep the antenna at least 5 - 6mm above the metal plate√ √
The antenna is at the same level of the metal plate.
For LED bulkhead
For 2D 28/38W lamp For LED panel light, motion sensor with daylight harvest
Great savings on electricity can be easily achieved with the employment of motion sensor. Hytronik has formulated a calculation tool for customers to simulate how much energy can be saved, how much less CO2 emmision can be reduced and how long is the payback period when applying the sensors for retrofit the old on/off installations; change over to sensorDIM, or ultimately adopt our constant lux control system --- daylight harvest system.
Please log in WWW.HYTRONIK.COM to download the calculation tool and see what you can do to contribute in the reduction of CO2 emmission!
2
Warranty
Hytronik offers 5 years product warranty to cover all kinds of product manufacturing defects, and Hytronik will be reliable for the cost envolved: 1. For product in HYTRONIK original brand, Hytronik takes care of all related cost including product cost, replacement cost etc. For the first 3 years; and only product cost for the rest 2 years. 2. For OEM customer branded product, Hytronik only takes care of the product cost.
Super compact sensor HC005S
LED array
LED linear fixture
Hytronik Microwave motion sensor 08
/ColorImageDict > /JPEG2000ColorACSImageDict > /JPEG2000ColorImageDict > /AntiAliasGrayImages false /CropGrayImages true /GrayImageMinResolution 300 /GrayImageMinResolutionPolicy /OK /DownsampleGrayImages true /GrayImageDownsampleType /Bicubic /GrayImageResolution 300 /GrayImageDepth -1 /GrayImageMinDownsampleDepth 2 /GrayImageDownsampleThreshold 1.50000 /EncodeGrayImages true /GrayImageFilter /DCTEncode /AutoFilterGrayImages true /GrayImageAutoFilterStrategy /JPEG /GrayACSImageDict > /GrayImageDict > /JPEG2000GrayACSImageDict > /JPEG2000GrayImageDict > /AntiAliasMonoImages false /CropMonoImages true /MonoImageMinResolution 1200 /MonoImageMinResolutionPolicy /OK /DownsampleMonoImages true /MonoImageDownsampleType /Bicubic /MonoImageResolution 1200 /MonoImageDepth -1 /MonoImageDownsampleThreshold 1.50000 /EncodeMonoImages true /MonoImageFilter /CCITTFaxEncode /MonoImageDict > /AllowPSXObjects false /CheckCompliance [ /None ] /PDFX1aCheck false /PDFX3Check false /PDFXCompliantPDFOnly false /PDFXNoTrimBoxError true /PDFXTrimBoxToMediaBoxOffset [ 0.00000 0.00000 0.00000 0.00000 ] /PDFXSetBleedBoxToMediaBox true /PDFXBleedBoxToTrimBoxOffset [ 0.00000 0.00000 0.00000 0.00000 ] /PDFXOutputIntentProfile () /PDFXOutputConditionIdentifier () /PDFXOutputCondition () /PDFXRegistryName () /PDFXTrapped /False
/CreateJDFFile false /Description > /Namespace [ (Adobe) (Common) (1.0) ] /OtherNamespaces [ > /FormElements false /GenerateStructure false /IncludeBookmarks false /IncludeHyperlinks false /IncludeInteractive false /IncludeLayers false /IncludeProfiles false /MultimediaHandling /UseObjectSettings /Namespace [ (Adobe) (CreativeSuite) (2.0) ] /PDFXOutputIntentProfileSelector /DocumentCMYK /PreserveEditing true /UntaggedCMYKHandling /LeaveUntagged /UntaggedRGBHandling /UseDocumentProfile /UseDocumentBleed false >> ]>> setdistillerparams> setpagedevice