Heating Cables...FATI power connection, splice, tee and end seal kit will reduce installation time....

Heating Cables For Industry Tracing

Inner insulation

Self-regulating semi-conductive core

Tinned copper braid

Tinned copper buswires16 AWG

Optional outer jacket

Features

· Energy efficient, automatically varies its power output in response to pipe temperature changes. · Easy to install, can be cut to any length (up to 125 meters) required on site with no wasted cable. · Lower installed cost than steam tracing, less maintenance expense and less downtime. · No overheat or burnout even when wrapped over itself (overlapped). · Suitable for use in non-hazardous, hazardous and corrosive environments. · FATI power connection, splice, tee and end seal kit will reduce installation time. · Optional outer jacket, the heating cable is resistant to watery and inorganic chemicals and corrosive.

Option

·FFHT-X…C Tinned copper or stainless steel braid provide additional mechanical protection and a positive groundpath. ·FFHT-X…CG High Temperature Fluoropolymer overjacket are used for exposure to organic or corrosive solutions or vapors may be present.

FFHT-X

Self Regulating Heating Cable

Application

FFHT-X is an industrial grade, ATEX approved self-regulating parallel heating cable (heating tape) manufactured in accordance to BS6351 Grade 22, that can be used for applications ranging from process heating or maintenance of temperature up to 120℃. It can be used in hazardous and non-hazardous locations, including areas where corrosives may be present.

FATI-FFHT-X · 1/2

Technical data

Service voltage 110V/230V

Maximum maintain temperature(power on) +120℃ (250℉)

Maximum exposure temperature (power off) +200℃ (390℉)

Minimum installation temperature -40℃ (-40℉)

Protective braid resistance ﹤18.2Ω/km

Bus wire gauge 16 AWG

Approvals EPT 16 ATEX 2551 X

0

10

20

30

40

0 10 20 30 40 50 60 70 80 90 100 110 120

W/m

°C

FATI-FFHT-X · 2/2

FFHT-X


Dimension and weight

Product ordering information Power output curvesNominal power output at 230V when FFHT-X is installed on insulated pipes.

Type Dimension Min.bending radius

Weight (kg/100m)

FFHT-X…C 9.3×4.4mm 26mm 9.7

FFHT-X…CT 10.3×5.4mm 32mm 9.5

B

For example: FFHT-X-15.2-CG

Outer jacketG=FluorpolymerTinned Copper BraidSupply Voltage1=110-120VAC; 2=220-277VAC

Power in W/m at +5°C15=15W/m; 30=30W/m

Type of cable

30FFHT-X

15FFHT-X

Start-up Temperature

Circuit Breaker Size

230V

120V

230V

120V

48

25

65

33

–40°

C

16A

72

36

100

50

–20°

C

85

43

120

60

–10°

C

110

55

155

78

10° C

66

34

85

43

–40°

C

20A

92

46

132

66

–20°

C

105

53

145

73

–10°

C

125

63

160

80

10° C

80

40

110

55

–40°

C

25A

115

58

160

80

–20°

C

120

60

160

80

–10°

C

125

63

160

80

10° C

98

50

140

70

–40°

C

32A

125

63

160

80

–20°

C

125

63

160

80

–10°

C

125

63

160

80

10° C

0

10

20

30

40

0 10 20 30 40 50 60 70 80 90100110120

°CPipe temperature °C

A 15FFHT-XB 30FFHT-X

A

F.A.T.I. Via A. Volta, 52 · 20090 Cusago (MI) [email protected] · www.fati.com

Maximum length (m) vs. circuit breaker size

W/m

FFHT-X -C

Inner insulation

Features

· Energy efficient, automatically varies its power output in response to pipe temperature changes. · Easy to install, can be cut to any length (up to 125 meters) required on site with no wasted cable. · Lower installed cost than steam tracing, less maintenance expense and less downtime. · No overheat or burnout even when wrapped over itself (overlapped). · Suitable for use in non-hazardous, hazardous and corrosive environments. · FATI power connection, splice, tee and end seal kit will reduce installation time. · Optional outer jacket, the heating cable is resistant to watery and inorganic chemicals and corrosive.

Option ·FFBT-X…C Tinned copper braid provide additional mechanical protection and a positive groundpath. ·FFBT-X…CG High Temperature Fluoropolymer overjacket are used for installationin hazardous location or where corrosive solutions or vapors may be present.

FFBT -X


Application

FFTB-X is an industrial grade, ATEX approved self-regulating parallel heating cable (heating tape) manufactured in accordance to BS6351 Grade 22, that can be used for applications ranging from process heating or maintenance of temperature up to 65℃. It can be used in hazardous and non-hazardous locations, including areas where corrosives may be present.

FATI-FFBT-X · 1/2

Technical data

Service voltage 110V/230V

Maximum maintain or continuous exposuretemperature (power on)

+65℃ (149℉)

Maximum intermittent exposure temperature 1000 hours (power on or off)

+75℃ (167℉)




Approvals EPT 16 ATEX 2551 X


Tinned copper braid



0

10

20

30

0 10 20 30 40 50 60 70

W/m

FATI-FFBT-X · 2/2


Product ordering information Power output curvesNominal power output at 230V when FFBT-X is installed on insulated pipes.


Weight (kg/100m)

FFBT-X…C 9.3×4.4mm 26mm 9.7

FFBT-X…CT 10.3×5.4mm 32mm 9.5

B

A

FFBT-X -C For example: FFBT-X-15.2-CG

Outer jacketG=FluoropolymerTinned Copper BraidSupply Voltage1=110-120VAC; 2=220-277VAC

Power in W/m at +5°C15=15W/m; 26=26W/m

Type of cable

FFBT-X


Maximum length (m) vs. circuit breaker size

26FFBT-X

15FFBT-X


Circuit Breaker Size

230V

120V

230V

120V

48

25

65

33

–40°

C

16A

72

36

100

50

–20°

C

85

43

120

60

–10°

C

110

55

155

78

10° C

66

34

85

43

–40°

C

20A

92

46

132

66

–20°

C

105

53

145

73

–10°

C

125

63

160

80

10° C

80

40

110

55

–40°

C

25A

115

58

160

80

–20°

C

120

60

160

80

–10°

C

125

63

160

80

10° C

98

50

140

70

–40°

C

32A

125

63

160

80

–20°

C

125

63

160

80

–10°

C

125

63

160

80

10° C


A 15FFBT-XB 26FFBT-X

Pipe temperature °C

0

10

20

30

0 10 20 30 40 50 60

W/m

°C

W/m

Features The FCTU series of self-regulating heating cables are designed to supply a specified amount of heat at any point along their length in direct response to local temperature variations. These cables can maintain temperatures up to 375°F (190°C) and will withstand 190 psig saturated steam purging and intermittent temperature excursions to 475°F (250°C) with power applied. FCTU cables can be cut to length and terminated in the field, and will not overheat or burnout when overlapped.

FCTU


Application

·The industrial grade FCTU cables provide freeze protection and process temperature maintenance for fluid transport and storage systems requiring very high levels of heat output or exposure to elevated temperatures. The bus wires, jackets and metallic braids can be configured for both ordinary (non-classified) locations and hazardous (classified), including areas where exposure to corrosive or organic materials is possible.

FATI-FCTU · 1/2

Technical data

Output wattage (other wattages also available) 15, 30, 45, 60w/m @ 0°C

Supply voltages 110-120 or 208V-277Vac

Continuous maintenance temperature 375°F (190°C) max

Intermittent exposure temperature 475°F (250°C) max

T Rating Temperature Class T2

Braid resistance 0.009Ohm/mt

Size 11.0mmx5.2mm

Min. bending radius 33mm

Self-regulating Fluoropolymer conductive core

Inner insulation

Nickel copper overshield

Nickel coated copper buswires


FCTUSelf Regulating Heating Cable

Product ordering information

FATI-FCTU · 2/2

Power Adjustment FactorPart No. 208 Volts 277 Volts

15FCTU2-CT 0.87 1.17

30FCTU2-CT 0.88 1.14

45FCTU2-CT 0.90 1.10

60FCTU2-CT 0.94 1.08

0

10

20

30

40

50

60

70

0 10 20 30 40 50 60 70 80 90 100110120130140150160170180

W/m

°C

C

D

B

A

A 15FCTUB 30FCTUC 45FCTUD 60FCTU


Power output curvesNominal power output at 230V when FCTU is installed on insulated pipes

FCTU - C For example: 15FCTU2-CTor example: 15HTP2-CTOuter jacketT=FluorpolymerNickel CopperSupply Voltage1=110-120VAC; 2=208-277VACType of cable

Power in W/mt at 10°C15=15W/mt; 30=30W/mt 45=45W/mt; 60=60W/mt


MinimumStart-up temperature

CB sizeAmps

15FCTU 30FCTU 45FCTU 60FCTU

120V 240V 120 V 240V 120 V 240V 120 V 240V

50℉(10℃)

15 55 110 37 73 24 49 18 35

20 73 146 49 98 32 64 27 46

30 102 165 55 110 41 82 37 70

0℉(-20℃)

15 50 99 32 70 21 43 17 33

20 67 131 43 93 27 56 21 44

30 100 165 55 110 41 82 34 67

-50℉(-45℃)

15 46 88 27 69 18 37 15 32

20 61 117 37 91 24 49 20 43

30 91 165 55 110 37 73 30 64

Maximum length (mt) vs. circuit breaker size

W/m

t

Features

· Energy efficient, automatically varies its power output in response to pipe temperature changes. · Easy to install, can be cut to any length (up to max circuit length) required on site with no wasted cable. · Lower installed cost than steam tracing, less maintenance expense and less downtime. · No overheat or burnout even when wrapped over itself (overlapped). · Suitable for use in non-hazardous, hazardous and corrosive environments. · FATI power connection, splice, tee and end seal kit will reduce installation time. Optional outer jacket, the heating cable is resistant to watery and inorganic chemicals and corrosive.

Option

·FCTS…C Tinned copper braid provide additional mechanical protection and a positive ground path. ·FCTS…CT High Temperature Fluoropolymer overjacket are used for exposure to organic or corrosive solutions or vapours may be present.

FCTS


Application

FCTS is an industrial grade, self-regulating parallel heating cable (heating tape) manufactured in accordance to BS6351 Grade 22, that can be used for applications ranging from process heating or maintenance of temperature up to 150℃. It can be used in hazardous and non-hazardous locations, including areas where corrosives may be present.

FATI-FCTS · 1/2

Technical data

Service voltage 110-120V, 220-277V

Maximum maintain or continuousexposure temperature (power on) +120℃ (248℉)


+200℃ (392℉)




Approvals CE


Inner insulation

Tinned copper braid



0

10

20

30

40

50

60

70

80

0 10 20 30 40 50 60 70 80 90 100 110 120

W/m

°C

FATI-FCTS · 2/2


FCTS



Product ordering information Power output curvesNominal power output at 240V when FCTS installed on insulated metal pipes.


A 5FCTSB 10FCTSC 15FCTSD 20FCTSD

C

B

A



CB sizeAmps

5FCTS230Vmt

10FCTS230Vmt

15FCTS230Vmt

20FCTS230Vmt

-20℃(-4℉)

16 120 80 55 40

25 205 125 85 65

32 220 155 105 80

40 220 155 135 110

10℃(50℉)

16 150 90 60 45

25 225 140 95 70

32 225 150 125 90

40 225 150 135 110


Weight (kg/100mt)

FCTS…C 9.2×3.6mm 21mm 11.2

FCTS…CR 10.9×6.0mm 36mm 11.0

FCTS - C For example: 15FCTS2-CT

Outer jacketT=FluorpolymerTinned Copper BraidSupply Voltage1=110-120VAC; 2=220-277VACType of cable

Power in W/mt at 10°C5=18W/mt; 10=35W/mt15=50W/mt; 20=65W/mt

W/m

t

Features

· Energy efficient, automatically varies its power output in response to pipe temperature changes.· Easy to install, can be cut to any length (up to max circuit length) required on site with no wasted cable.· Lower installed cost than steam tracing, less maintenance expense and less downtime.· No overheat or burnout even when wrapped over Itself (overlapped) .· Suitable for use in non-hazardous, hazardous and corrosive environments.· FATI power connection, splice, tee and end seal kit will reduce installation time. Optional outer jacket, the heating cable is resistant to watery and inorganic chemicals corrosive

Option

·FCTR…C Tinned copper braid provide additional mechanical protection and a positive ground path. ·FCTR…CR Flame retardant thermoplastic over jacket protect against certain inorganic chemical solutions, it also protect against abrasion and impact damage. ·FCTR…CT High Temperature Fluoropolymer. Over jacket are used for exposure to organic or corrosive solutions or vapours.

FCTR


Application

FCTR is Industrial Rate approved self-regulating parallel heating cable (heating tape), designed for a variety of industrial applications and enviroments, including hazardous and non-hazardous. It can be used for plastic or mental pipe freeze protection and flow maintenance of pipes, tanks, valves.

FATI-FCTR · 1/2

Technical data




+85℃ (185℉)





Inner insulation

Tinned copper braid



0

10

20

30

40

50

60

0 10 20 30 40 50 60 70

W/m

°C

Power output curvesNominal power output at 240V when FCTR installed on insulated metal pipes.


C

B

E

A

D

A 3FCTRB 5FCTRC 8FCTRD 10FCTRE 12FCTR

FCTRSelf Regulating Heating Cable


FATI-FCTR · 2/2



Weight (kg/100mt)

FCTR…C 11.0×4.4mm 26mm 10.5

FCTR…CR 12.6×6.0mm 36mm 13.8

FCTR…CT 12.0×5.4mm 32mm 13.0

FCTR - C For example: 5FCTR2-CT

Outer jacketR=Thermoplastic; T=FluorpolymerTinned Copper BraidSupply Voltage1=110-120VAC; 2=220-277VACType of cable

Power in W/mt at 10°C3=12W/mt; 5=18W/mt; 8=25W/mt 10=35W/mt; 12=42W/mt


Circuit Breaker

Size


3FCTR 5FCTR 8FCTR 10FCTR 12FCTR

120V 230V 120V 230V 120V 230V 120V 230V 120V 230V

16A

–40°C 48 95 48 67 48 48 48 38 48 28

–20°C 76 150 76 105 76 70 76 45 76 35

–10°C 86 170 86 125 86 82 86 50 86 40

10°C 100 200 100 158 100 110 100 65 100 52

20A

–40°C 63 125 63 90 63 64 63 50 63 36

–20°C 96 190 96 136 96 90 96 55 96 48

–10°C 98 195 98 145 98 103 98 65 98 54

10°C 100 200 100 160 100 125 100 85 100 64

25A

–40°C 78 155 78 110 78 76 78 62 78 48

–20°C 100 200 100 160 100 110 100 70 100 60

–10°C 100 200 100 160 100 120 100 92 100 76

10°C 96 190 96 140 96 96 96 80 96 60

32A

–40°C 96 190 96 140 96 96 96 80 96 60

–20°C 100 200 100 160 100 125 100 90 100 75

–10°C 100 200 100 160 100 125 100 102 100 87

10°C 100 200 100 160 100 125 100 110 100 95


W/m

t

Features

· Energy efficient, automatically varies its power output in response to pipe temperature changes. · Easy to install, can be cut to any length (up to max circuit length) required on site with no wasted cable. · Lower installed cost than steam tracing, less maintenance expense and less downtime. · No overheat or burnout even when wrapped over Itself (overlapped). · Suitable for use in non-hazardous, hazardous and corrosive environments. · FATI power connection, splice, tee and end seal kit will reduce installation time. · Optional outer jacket, the heating cable is resistant to watery and inorganic chemicals and corrosive.

Option

·FCTP…C Tinned copper braid provide additional mechanical protection and a positive ground path. ·FCTP…CR Flame retardant thermoplastic over jacket protect against certain inorganic chemical solutions, it also protect against abrasion and impact damage. ·FCTP…CT High Temperature Fluoropolymer over jacket are used for exposure to organic or corrosive solutions or vapours may be present.

FCTP


Application

FCTP is Industrial Rated approved self-regulating parallel heating cable, designed for pipe heat tracing in industrial applications, it is configured for use in hazardous and non-hazardous locations, including areas where corrosives may be present. It can provide process temperature maintenance up to 110℃ (230℉) and it can also be used for frost protection of large pipes and freeze protection in systems having high heat loss.

FATI-FCTP · 1/2

Technical data




+135℃ (275℉)



Bus wire gauge 16 AWG (17&31W/mt)14 AWG (45&60W/mt)

Approvals CE


Inner insulation

Tinned copper braid

Tinned copper buswires14 AWG/16 AWG


0

10

20

30

40

50

60

70

80

0 10 20 30 40 50 60 70 80 90 100 110

W/m

°C

FATI-FCTP · 2/2


FCTP



Product ordering information Power output curvesNominal power output at 230V when FCTP is installed on insulated pipes.



Weight (kg/100mt)

FCTP…C 12.0x4.4 26mm 9.5

FCTP…CR 13.6x6.0 36mm 11.0

FCTP…CT 12.4x4.8 28mm 13.9

A 5FCTPB 10FCTPC 15FCTPD 20FCTPD

C

B

A



CB sizeAmps

5FCTP230Vmt

10FCTP230Vmt

15FCTP230Vmt

20FCTP230Vmt

-20℃(-4℉)

16 110 65 63 47

25 130 95 75 60

32 130 115 100 75

40 130 115 100 95

10℃(50℉)

16 120 80 63 47

25 130 115 95 75

32 130 115 100 95

40 130 115 100 95

FCTP - C For example: 5FCTP2-CT



W/m

t

Features · Energy efficient, automatically varies its power output in response to pipe temperature changes.· Easy to install, can be cut to any length (up to max circuit length) required on site with no wasted cable.· Lower installed cost than steam tracing, less maintenance expense and less downtime.· No overheat or burnout even when wrapped over Itself (overlapped).· Suitable for use in non-hazardous, hazardous and corrosive environments.· FATI power connection, splice, tee and end seal kit will reduce installation time. Optional outer jacket, the heating cable is resistant to watery and inorganic chemicals and corrosive.

Option

·FCTM…C Tinned copper braid provide additional mechanical protection and a positive ground path. ·FCTM…CR Flame retardant thermoplastic over jacket protect against certain inorganic chemical solutions, it also protect against abrasion and impact damage. ·FCTM…CT High Temperature Fluoropolymer over jacket are used for exposure to organic or corrosive.

FCTM


Application

FCTM is self-regulating parallel heating cable (heating tape) can provides safe, reliable heat tracing for freeze protection or temperature maintenance of pipes, valves, flanges. It is suitable for use on small diameter plastic or mental pipes and instrument tubing in residential/light commercial and similar applications.

FATI-FCTM · 1/2

Technical data




+85℃ (185℉)





Inner insulation

Tinned copper braid



0

10

20

30

40

0 10 20 30 40 50 60 70

W/m

°C

FCTMSelf Regulating Heating Cable

Product ordering information Power output curvesNominal power output at 230V when FCTM is installed on insulated pipes


FATI-FCTM · 2/2

C

B

A


A 3FCTMB 5FCTMC 8FCTM


Weight (kg/100mt)

FCTM…C 7.8×4.9mm 29mm 6.0

FCTM…CR 8.6×5.7mm 34mm 7.5

FCTM…CT 8.0×5.1mm 30mm 7.1



CB sizeAmps

3FCTM230Vmt

5FCTM230Vmt

8FCTM230Vmt

10℃(50℉)

10 123 85 65

16 128 102 88

25 128 112 117

0℃(32℉)

10 98 81 52

16 120 99 77

25 120 102 103


FCTM - C For example: 5FCTM2-CR


Power in W/mt at 10°C3=15W/mt; 5=18W/mt 8=28W/mt

W/m

t

Features · Energy efficient, automatically varies its power output in response to pipe temperature changes. · Easy to install, can be cut to any length (up to max circuit length) required on site with no wasted cable. · Lower installed cost than steam tracing, less maintenance expense and less downtime. · No overheat or burnout even when wrapped over itself (overlapped). · Suitable for use in non-hazardous, hazardous and corrosive environments. · FATI power connection, splice, tee and end seal kit will reduce installation time. Optional outer jacket, the heating cable is resistant to watery and inorganic chemicals and corrosive.

Option

·FCTL…C Tinned copper braid provide additional mechanical protection and a positive groundpath. ·FCTL…CR Flame retardant thermoplastic overjacket protect against certain inorganic chemical solutions, it also protects against abrasion and impact damage. ·FCTL…CT High Temperature Fluoropolymer overjacket are used for exposure to organic or corrosive solutions or vapors may be present.

FCTL


Application

FCTL is CE compliant self-regulating parallel heating cable (heating tape) is designed for residentialand commercial metal and plastic pipe freeze protection and roof and gutter de-icing applications. It is ideal for use in maintaining fluid flow under low ambient. Freeze protection and low watt density process temperature systems such us pipelines, fire protection, process water, dust suppression systems, hot water and structure anti-icing are typical applications for this product. A UV stabilized thermoplastic elastomer overjacket is provided to cover the braid for wet applications and exposure to the sun.

FATI-FCTL · 1/2

Technical data




+85℃ (185℉)




Approvals CE


Inner insulation

Tinned copper braid



FCTL



Power output curvesNominal power output at 230V when FCTLis installed on insulated pipes


FATI-FCTL · 2/2



Weight (kg/100mt)

FCTL…C 9.3×4.4mm 26mm 9.7

FCTL…CR 10.9×6.0mm 36mm 11.0

FCTL…CT 10.3×5.4mm 32mm 9.5

0

10

20

30

40

50

0 10 20 30 40 50 60 70

W/m

°C

A 3FCTLB 5FCTLC 8FCTLD 10FCTL

FCTL - C For example: 5FCTL-CR




Circuit Breaker

Size


3FCTL 5FCTL 8FCTL 10FCTL

120V 230V 120V 230V 120V 230V 120V 230V

16A

–40°C 46 90 33 65 25 48 18 36

–20°C 73 145 50 100 36 72 22 42

–10°C 83 165 60 120 43 85 25 48

10°C 100 200 78 155 55 110 32 62

20A

–40°C 60 120 43 85 34 66 25 48

–20°C 93 185 66 132 46 92 26 52

–10°C 95 190 73 145 53 105 32 62

10°C 100 200 80 160 63 125 42 82

25A

–40°C 76 152 55 110 40 80 30 60

–20°C 100 200 80 160 58 115 35 68

–10°C 100 200 80 160 60 120 45 90

10°C 100 200 80 160 63 125 50 100

32A

–40°C 95 188 70 140 50 98 40 78

–20°C 100 200 80 160 63 125 45 88

–10°C 100 200 80 160 63 125 50 100

10°C 100 200 80 160 63 125 53 105


D

C

B

A

W/m

t

Application FCHW self-regulating heating cable are installed on hot water supply pipes underneath standard pipe insulation.The heating cable replaces supply-pipe heating loses at the point where the heat loss occurs, thereby providing continuous, energy-efficient, hot water temperature maintainance and eliminating theneed for a recirculation.

FCHW


Features

·Energy efficient, automatically varies its power output to compensate for variations in water temperature and ambient temperature. ·Easy to install, can be cut to any length (up to max. circuit length) required on site with no wasted cable. ·Lower installed cost than steam tracing, less maintenance expense and less downtime. ·No overheat or burnout even when wrapped over itself (overlapped). ·Low operating cost, the FCHW system continuously maintains hot water temperature at every point along the supply pipe. ·FCHW systems eliminate the need for designing complex recirculation systems, with their pumps, piping net-works, and complicated flow balancing.

FATI-FCHW · 1/2


Inner insulation

Tinned copper braid



Immediate hot water when required

FCHWSelf Regulating Heating Cable

FATI-FCHW · 2/2

Specifications

FCHW-Y FCHW-O FCHW-R

Breaker size 230V 230V 230V

13A 110mt 65mt 65mt

16A 140mt 80mt 80mt

20A 180mt 100mt 100mt

MODEL FCHW-Y FCHW-O FCHW-R

Jacket color Yellow Orange Red

Bus wires 16 AWG 16 AWG 16 AWG

Maintainance temperature 40℃ to 50℃ 40℃ to 50℃ 40℃ to 60℃

Max. exposure temperature 65°C 65°C 80°C

Nominal power output 7 W/mt at 45°C 9 W/mt at 55°C 12 W/mt at 70°C

Minimum bend radius 20mm 20mm 20mm

Supply voltage 208~240V 208~240V 208~240V

Maximum circuit length


W W W . F A T I . C O M

F.A.T.I. Srl Via Volta, 52

20090 Cusago (Milano - Italy) Tel. +39 0290119641 Fax +39 029019548

E-mail [email protected]

Heating Cables...FATI power connection, splice, tee and end seal kit will reduce installation time....

Documents

Transcript of Heating Cables...FATI power connection, splice, tee and end seal kit will reduce installation time....