Heating and Cooling Coils - Trane · Coils can be selected for the following: • Chilled Water •...
8
Heating and Cooling Coils Coils for All Comfort, Commercial and Industrial Applications
Transcript of Heating and Cooling Coils - Trane · Coils can be selected for the following: • Chilled Water •...
Delta-Flo™ Fin Design
The Delta-Flo coil features astaggered 1/2-inch tube pattern andunique fin design allowing for lowairside pressure drop with highcapacity for lower gpmapplications. With staggered tubesand its unique fin configuration,the Delta-Flo coil is one of the mostefficient half-inch coils available inthe industry. Delta-Flo coils areavailable in the original Delta-FloE
®
fin surface and the new Delta-FloH®
enhanced fin surface. Delta-Flo Hfins offer increased capacities andhigher moisture carryover limitswhen compared to the originalDelta-Flo E fins. Delta-Flo E andDelta-Flo H are available inaluminum fins.
Prima-Flo®Fin Design
The Prima-Flo coil features aparallel 5/8-inch tube pattern. Theenergy efficient Prima-Flo Efinsurface is designed to decreasestatic pressure loss through thecoil. This fin is ideal for systemswhere airside pressure drop is amajor concern. Reducing pressuredrop through the coil results inlower fan brake horsepower andsystem energy savings. Prima-Flocoils are available in the originalPrima-Flo Efin surface and the newPrima-Flo Henhanced fin surface.Prima-Flo Hfins offer increasedcapacities and moisture carryoverlimits when compared to theoriginal Prima-Flo Efins. Prima-Flo Eand Prima-Flo Hareavailable in aluminum fins.
Sigma-Flo® Fin Design
The Sigma-Flo coil is available in a5/8-inch and 1-inch parallel tubepattern. The Sigma-Flo fin isdesigned to maximize heat transferand minimize coil size. The 5/8-inch Sigma-Flo tube pattern is availablewith COPPER fins only. The 1-inchSigma-Flo tube pattern for use withsteam coils is available withaluminum or copper fins.
Better Performance Using
Trane IVS
Infinitely variable fin spacing (IVS)gives the designer many ways toselect the right coil for a particularjob.
IVS fins are available on all coil finsurfaces for coil selections tailoredto application needs. This flexibilityis important since coil heating orcooling loads can be matchedmore precisely than traditional"fixed" fin spacing. For example, a Delta-Flo Ecooling coil can beselected from 72 fins per foot to168 fins per foot in one-finincrements.
In many cases IVS fins will allowdesigners to reduce the number offins required to meet coil loads.Fewer fins can result in lowerairside pressure drops and lowerfan brake horsepower, savingvaluable energy dollars. Reducingthe fan BHP may allow theselection of a smaller fan motor ora smaller air handler, savingadditional dollars.
Using IVS and the five fin surfaceoptions, the designer has moreflexibility than ever to design andselect coils.
Computerized Selection
Programs
For quick, easy and accurate coilselections, as well as greaterflexibility in design decisions, TheTrane Company has developedcomputerized selection programs.These programs are available fromyour local Trane office.
Coils can be selected for thefollowing:
• Chilled Water
• Hot Water
• Steam
• Refrigerant
• Refrigerant Heat Recovery
• Coil Runaround Loop HeatRecovery
Based on initial input conditions,the programs will calculatecapacity, air pressure drop andwater pressure drop for all watercoils and steam pressure drop forsteam coils, including coils withcopper fins or coils requiringheavier tube thicknesses.
Improve system efficiency with 25coil types, five fin surfaces, IVS anda wide selection of refrigerant coilcircuiting options. Since pumpingcosts are typically lower thanairside operating costs, increaseavailable waterflow to reduce finrequirements and airside pressuredrops for fan energy savings.
Heating and
Cooling Coils
Coils for All Comfort,
Commercial and
Industrial Applications
More Coils for More Uses
C.D.S.Network
The Trane Customer DirectService Network™ is acomputerized engineeringdesign service providing time-tested software and access topersonal computer programs.Complete with a communicationspackage to support it, C.D.S.delivers HVAC program updatesand user support instantly.
With the variety of header designfeatures and material flexibility,along with IVS and computerselection programs, Trane provesagain it’s the leader in coiltechnology.
Infinitely Variable Fin Spacing
Delta-Flo™
Prima-Flo®
and
Sigma-Flo®
Unique Design
Energy Efficient
Cost-Effective
© American Standard Inc. 1998
File No. COIL-TS-1 August 1998
Supersedes COIL-TS-1-1189
File No. PL-AH-COIL-000-TS-1-898
Worldwide Applied Systems Group
The Trane Company3600 Pammel Creek RoadLa Crosse, WI 54601-7599www.trane.com
An American Standard CompanySince The Trane Company has a policy of continuous product improvement, it reserves the right to change design and specification without notice.
Delta-Flo™ Fin Design
The Delta-Flo coil features astaggered 1/2-inch tube pattern andunique fin design allowing for lowairside pressure drop with highcapacity for lower gpmapplications. With staggered tubesand its unique fin configuration,the Delta-Flo coil is one of the mostefficient half-inch coils available inthe industry. Delta-Flo coils areavailable in the original Delta-Flo E®
fin surface and the new Delta-FloH®
enhanced fin surface. Delta-Flo Hfins offer increased capacities andhigher moisture carryover limitswhen compared to the originalDelta-Flo E fins. Delta-Flo E andDelta-Flo H are available inaluminum fins.
Prima-Flo® Fin Design
The Prima-Flo coil features aparallel 5/8-inch tube pattern. Theenergy efficient Prima-Flo E finsurface is designed to decreasestatic pressure loss through thecoil. This fin is ideal for systemswhere airside pressure drop is amajor concern. Reducing pressuredrop through the coil results inlower fan brake horsepower andsystem energy savings. Prima-Flocoils are available in the originalPrima-Flo E fin surface and the newPrima-Flo H enhanced fin surface.Prima-Flo H fins offer increasedcapacities and moisture carryoverlimits when compared to theoriginal Prima-Flo E fins. Prima-Flo E and Prima-Flo H areavailable in aluminum fins.
Sigma-Flo® Fin Design
The Sigma-Flo coil is available in a5/8-inch and 1-inch parallel tubepattern. The Sigma-Flo fin isdesigned to maximize heat transferand minimize coil size. The 5/8-inch Sigma-Flo tube pattern is availablewith COPPER fins only. The 1-inchSigma-Flo tube pattern for use withsteam coils is available withaluminum or copper fins.
Better Performance Using
Trane IVS
Infinitely variable fin spacing (IVS)gives the designer many ways toselect the right coil for a particularjob.
IVS fins are available on all coil finsurfaces for coil selections tailoredto application needs. This flexibilityis important since coil heating orcooling loads can be matchedmore precisely than traditional"fixed" fin spacing. For example, a Delta-Flo E cooling coil can beselected from 72 fins per foot to168 fins per foot in one-finincrements.
In many cases IVS fins will allowdesigners to reduce the number offins required to meet coil loads.Fewer fins can result in lowerairside pressure drops and lowerfan brake horsepower, savingvaluable energy dollars. Reducingthe fan BHP may allow theselection of a smaller fan motor ora smaller air handler, savingadditional dollars.
Using IVS and the five fin surfaceoptions, the designer has moreflexibility than ever to design andselect coils.
Computerized Selection
Programs
For quick, easy and accurate coilselections, as well as greaterflexibility in design decisions, TheTrane Company has developedcomputerized selection programs.These programs are available fromyour local Trane office.
Coils can be selected for thefollowing:
• Chilled Water
• Hot Water
• Steam
• Refrigerant
• Refrigerant Heat Recovery
• Coil Runaround Loop HeatRecovery
Based on initial input conditions,the programs will calculatecapacity, air pressure drop andwater pressure drop for all watercoils and steam pressure drop forsteam coils, including coils withcopper fins or coils requiringheavier tube thicknesses.
Improve system efficiency with 25coil types, five fin surfaces, IVS anda wide selection of refrigerant coilcircuiting options. Since pumpingcosts are typically lower thanairside operating costs, increaseavailable waterflow to reduce finrequirements and airside pressuredrops for fan energy savings.
Heating and
Cooling Coils
Coils for All Comfort,
Commercial and
Industrial Applications
More Coils for More Uses
C.D.S. Network
The Trane Customer DirectService Network™ is acomputerized engineeringdesign service providing time-tested software and access topersonal computer programs.Complete with a communicationspackage to support it, C.D.S.delivers HVAC program updatesand user support instantly.
With the variety of header designfeatures and material flexibility,along with IVS and computerselection programs, Trane provesagain it’s the leader in coiltechnology.
Infinitely Variable Fin Spacing
Delta-Flo™
Prima-Flo® and
Sigma-Flo®
Unique Design
Energy Efficient
Cost-Effective
© American Standard Inc. 1998
File No. COIL-TS-1 August 1998
Supersedes COIL-TS-1-1189
File No. PL-AH-COIL-000-TS-1-898
Worldwide Applied Systems Group
The Trane Company3600 Pammel Creek RoadLa Crosse, WI 54601-7599www.trane.com
An American Standard CompanySince The Trane Company has a policy of continuous product improvement, it reserves the right to change design and specification without notice.
Delta-Flo™ Fin Design
The Delta-Flo coil features astaggered 1/2-inch tube pattern andunique fin design allowing for lowairside pressure drop with highcapacity for lower gpmapplications. With staggered tubesand its unique fin configuration,the Delta-Flo coil is one of the mostefficient half-inch coils available inthe industry. Delta-Flo coils areavailable in the original Delta-Flo E®
fin surface and the new Delta-FloH®
enhanced fin surface. Delta-Flo Hfins offer increased capacities andhigher moisture carryover limitswhen compared to the originalDelta-Flo E fins. Delta-Flo E andDelta-Flo H are available inaluminum fins.
Prima-Flo® Fin Design
The Prima-Flo coil features aparallel 5/8-inch tube pattern. Theenergy efficient Prima-Flo E finsurface is designed to decreasestatic pressure loss through thecoil. This fin is ideal for systemswhere airside pressure drop is amajor concern. Reducing pressuredrop through the coil results inlower fan brake horsepower andsystem energy savings. Prima-Flocoils are available in the originalPrima-Flo E fin surface and the newPrima-Flo H enhanced fin surface.Prima-Flo H fins offer increasedcapacities and moisture carryoverlimits when compared to theoriginal Prima-Flo E fins. Prima-Flo E and Prima-Flo H areavailable in aluminum fins.
Sigma-Flo® Fin Design
The Sigma-Flo coil is available in a5/8-inch and 1-inch parallel tubepattern. The Sigma-Flo fin isdesigned to maximize heat transferand minimize coil size. The 5/8-inch Sigma-Flo tube pattern is availablewith COPPER fins only. The 1-inchSigma-Flo tube pattern for use withsteam coils is available withaluminum or copper fins.
Better Performance Using
Trane IVS
Infinitely variable fin spacing (IVS)gives the designer many ways toselect the right coil for a particularjob.
IVS fins are available on all coil finsurfaces for coil selections tailoredto application needs. This flexibilityis important since coil heating orcooling loads can be matchedmore precisely than traditional"fixed" fin spacing. For example, a Delta-Flo E cooling coil can beselected from 72 fins per foot to168 fins per foot in one-finincrements.
In many cases IVS fins will allowdesigners to reduce the number offins required to meet coil loads.Fewer fins can result in lowerairside pressure drops and lowerfan brake horsepower, savingvaluable energy dollars. Reducingthe fan BHP may allow theselection of a smaller fan motor ora smaller air handler, savingadditional dollars.
Using IVS and the five fin surfaceoptions, the designer has moreflexibility than ever to design andselect coils.
Computerized Selection
Programs
For quick, easy and accurate coilselections, as well as greaterflexibility in design decisions, TheTrane Company has developedcomputerized selection programs.These programs are available fromyour local Trane office.
Coils can be selected for thefollowing:
• Chilled Water
• Hot Water
• Steam
• Refrigerant
• Refrigerant Heat Recovery
• Coil Runaround Loop HeatRecovery
Based on initial input conditions,the programs will calculatecapacity, air pressure drop andwater pressure drop for all watercoils and steam pressure drop forsteam coils, including coils withcopper fins or coils requiringheavier tube thicknesses.
Improve system efficiency with 25coil types, five fin surfaces, IVS anda wide selection of refrigerant coilcircuiting options. Since pumpingcosts are typically lower thanairside operating costs, increaseavailable waterflow to reduce finrequirements and airside pressuredrops for fan energy savings.
Heating and
Cooling Coils
Coils for All Comfort,
Commercial and
Industrial Applications
More Coils for More Uses
C.D.S. Network
The Trane Customer DirectService Network™ is acomputerized engineeringdesign service providing time-tested software and access topersonal computer programs.Complete with a communicationspackage to support it, C.D.S.delivers HVAC program updatesand user support instantly.
With the variety of header designfeatures and material flexibility,along with IVS and computerselection programs, Trane provesagain it’s the leader in coiltechnology.
Infinitely Variable Fin Spacing
Delta-Flo™
Prima-Flo® and
Sigma-Flo®
Unique Design
Energy Efficient
Cost-Effective
© American Standard Inc. 1998
File No. COIL-TS-1 August 1998
Supersedes COIL-TS-1-1189
File No. PL-AH-COIL-000-TS-1-898
Worldwide Applied Systems Group
The Trane Company3600 Pammel Creek RoadLa Crosse, WI 54601-7599www.trane.com
An American Standard CompanySince The Trane Company has a policy of continuous product improvement, it reserves the right to change design and specification without notice.
• DRAINABLE AT HEADER 1* 6, 9, 12, 18 12"-168" ALUMINUM COPPER 200 325 (1-ROW)• LOW GPM 24, 30, 33" 80-168 5⁄8" OD 200 220 (2-ROW)• ALTERNATIVE-TUBE FEED .020"• HOT WATER .024"
.035"2 12, 18, 24, COPPER RED BRASS 200 388 (1-ROW)
30, 33"" 96-168 .049" 200 220 (2-ROW)
• DRAINABLE AT HEADER 1 CAST IRON HDR. 12"-168" ALUMINUM COPPER• ONE-ROW 12, 18, 24 80-168 5⁄8" OD• SAME-END CONNECTION 30, 33" .020"• HOT WATER .024"
COPPER HDR .035"36, 42, 48" COPPER 200 250
96-168 RED BRASS.049"
(CAST IRONHDR ONLY)
• GENERAL PURPOSE 1* 6, 9, 12, 18 ALUMINUM COPPER• DRAINABLE AT HEADER 24, 30, 33" 80-168 5⁄8" OD 200 325 (1-ROW)• FULL-ROW SERPENTINE .020" 200 220 (2-ROW)• HOT WATER .024"
.035"2 (CAST IRON HDR) 12"-168" COPPER RED BRASS 200 388 (1-ROW)
12, 18, 24 96-168 .049" 200 220 (2-ROW)30, 33"
(COPPER HDR)36, 42, 48, 54"
• LOW GPM 1 12, 18 ALUMINUM COPPER• COMMON DUCT COIL 24, 30" 80-168 5⁄8"OD 225 250• TWO-TUBE FEED .020"• HOT WATER .024"
.035" 275 3502 9, 12, 18 12"-96" COPPER RED BRASS
24, 30, 33" 96-168 .049" 350 400
• LOW GPM OR MODERATE 1 6, 9, 12 (T) 6"-72" ALUMINUM COPPER WATER 200 250STEAM PRESSURES 15, 18" 80, 110, 150 5⁄8"OD STEAM 100 400
• COMMON DUCT COILS (ST) 6”-42” .020".024"
• T HAS STANDARD CASING. COPPER 035" WATER 275 350• ST HAS SLIP FLANGE 96, 110, 144 STEAM 350 400
CASING FOR QUICK FIT-UP• HOT WATER OR STEAM 2 RED BRASS WATER 350 400
.049" STEAM 400 450
• GENERAL PURPOSE 2, 3, 4, 6 CAST IRON HDR 12"-168" ALUMINUM COPPER 200 220• DRAINABLE AT HEADER 8, 10, 12 12, 18, 24, 80-168 5⁄8" OD• FULL-ROW SERPENTINE 30, 33’’ .020"• CHILLED WATER .024"
.035"
COPPER HDR 12"-168" COPPER RED BRASS36, 42, 48, 54" 96-168 .049"
• CLEANABLE 2, 4, 6 12, 18, 24 12"-168" ALUMINUM COPPER 200 220• DRAINABLE AT EACH ROW 8, 10, 12 30, 33" 80-168 5⁄8" OD• FULL-ROW SERPENTINE .020"• CHILLED WATER .024"
.035"3*
COPPER RED BRASS96-168 .049"
• LOW GPM 2, 4, 6 12, 18 12"-120" ALUMINUM COPPER 200 220• TWO-TUBE FEED 24, 30" 80-168 5⁄8" OD• CHILLED WATER .020"
.024"
.035"
COPPER RED BRASS96-168 .049"
• LOW GPM 2, 4 12, 18 12"-120" ALUMINUM COPPER 200 220• FOUR-TUBE FEED 6, 8 24, 30" 80-168 5⁄8" OD• CHILLED WATER .020"
.024"
.035"
COPPER RED BRASS96-168 .049"
• LOW GPM 4, 8 18, 24 18"-120 ALUMINUM COPPER 200 220• EIGHT-TUBE FEED 30" 80-168 5⁄8" OD• CHILLED WATER .020"
.024"
.035"
COPPER RED BRASS96-168 .049"
• DRAINABLE AT EACH ROW 4, 6, 8 12, 18, 24 12"-168" ALUMINUM COPPER 200 220• FULL-ROW SERPENTINE 10, 12 30, 33" 80-168 5⁄8" OD• CHILLED WATER .020"
.024"
.035"3*
COPPER RED BRASS96-168 .049"
• DRAINABLE AT EACH ROW 4,8,12 CAST IRON HDR 18"-168" ALUMINUM COPPER 200 220• HIGH GPM 18, 24, 80-168 5⁄8" OD• LOW WATER PRESSURE DROP 6, 10* 30, 33’’ .020"• OPPOSITE-END CONNECTIONS .024"
ON 6 & 10 ROWS .035"• DUAL-ROW SERPENTINE• CHILLED WATER• DRAINABLE AT HEADER• HIGH GPM• LOW WATER PR ESSURE DROP 6, 8 CAST IRON HDR COPPER RED BRASS• SAME-END CONNECTIONS 10, 12 18,24, 96-168 .049"
ON 6 & 10 ROWS 30,33"• DUAL-ROW SERPENTINE COPPER HDR• CHILLED WATER 36, 42, 48, 54"
• GENERAL PURPOSE 2, 4 12, 18, 24 12"-168" ALUMINUM COPPER 200 220• FULL-ROW SERPENTINE 6, 8 30, 33, 36, 1⁄2" OD• CHILLED WATER 42, 48, 54" .016"
DELTA-FLO E72-168 .025"
DELTA-FLO H84-168
• DRAINABLE AT HEADER 2, 4, 6 12, 18, 24, 12"-168" ALUMINUM COPPER 200 220• FULL-ROW SERPENTINE 30, 33, 36 1⁄2" OD• CHILLED WATER 42, 48, 54" .016"
DELTA-FLO E72-168 .025"
DELTA-FLO H84-168
• DRAINABLE AT HEADER 4, 6, 8 18, 24, 30 18"-168" ALUMINUM COPPER 200 220• HIGH GPM 33, 36, 42 1⁄2" OD• LOW WATER PRESSURE DROP 48, 54" .016"• DUAL-ROW SERPENTINE DELTA-FLO E• CHILLED WATER 72-168 .025"
DELTA-FLO H84-168
• REFRIGERANT 2, 3, 4 12, 18, 24 12"-168" ALUMINUM COPPER 300• CIRCUITING AVAILABLE: 6,8 30, 33" 80-168 5⁄8" OD
STANDARD .020"HORIZONTAL SPLIT COPPER .024"VERTICAL SPLIT 96-168
• REFRIGERANT 4, 6 18, 24, 30 18"-168" ALUMINUM COPPER 300• CIRCUITING AVAILABLE: 33, 36, 42 1⁄2" OD
STANDARD 48" .016"HORIZONTAL SPLIT DELTA-FLO EVERTICAL SPLIT 72-168 .025"INTERTWINED
DELTA-FLO H84-168
• UNMODULATED STEAM TYPE 1* 6, 9, 12, 12"-120" ALUMINUM COPPER 100 400• FULL-ROW FEED 18, 24, 30 80-168 5⁄8" OD• STEAM 33’’ .020"
COPPER .024"96-168 .035"
RED BRASS.049" 200 400
• MODULATING STEAM TYPE 1* 12, 18, 24 12"-144" ALUMINUM COPPER• STEAM DISTRIBUTING TYPE 30, 33 42-132 1" OD 100 400• FULL-ROW FEED 30,33" .031"• OPPOSITE-END CONNECTIONS
• SAME-END CONNECTIONS COPPER RED BRASS• STEAM 1 42-132 .049" 200 400
• REFRIGERANT 1,2 12, 18, 24, 24"-168" ALUMINUM COPPER 300• 1-100% HEAT RECOVERY 3,4 30, 33, 36 80-168 5⁄8" OD• MULTIPLE-COMPRESSOR 6 42, 48" .020"
CIRCUITS 54 (2-6 ROW ONLY)
• GENERAL PURPOSE 2 12, 18, 24 12"-168" ALUMINUM COPPER 200 220• FULL-ROW SERPENTINE 30, 33, 36 1⁄2" OD• HOT WATER 42, 48, 54" .016"
DELTA-FLO E72-180 .025"
DELTA-FLO H84-180
• DRAINABLE AT HEADER 2 12,18,24 12"-168" ALUMINUM COPPER 200 220• FULL-ROW SERPENTINE 30, 33, 36 DELTA-FLO E 1⁄2" OD • HOT WATER 42, 48, 54" 72-180 .016"
DELTA-FLO H84-180 .025"
WATERIN
WATEROUT
AIRFLOW
WATERIN
WATEROUT
WATERIN
WATEROUT
WATERIN
WATEROUT
AIRFLOW
REFRIGERANTGAS IN
REFRIGERANTGAS/ LIQUID
OUT
STEAMIN
CONDENSATEOUT
STEAMIN
CONDENSATEOUT
Notes:
1. Turbulators are available in water coils to increase capacities at low fluid flow rates. 2. Special material construction, operating pressures and temperatures are available. 3. All chilled water coils can be used in hot water applications. 4. Drain and vent connections are standard on all water coils. 5. All finned lengths are available in one inch increments (except T and ST coils). 6. All fin spacings are available in one fin per foot increments.
*Opposite-end connection. †ARI certification does not exist for type H coils.
Heating CoilsMAX. STD. OPERATING
CONDITIONSFINNED FINNED FINS TUBE PSI TEMP (F)
CHARACTERISTICS ROWS WIDTH LENGTH PER FOOT MATERIAL (TUBE SIDE)
MAX. STD. OPERATING CONDITIONS
FINNED FINNED FINS TUBE PSI TEMP (F)CHARACTERISTICS ROWS WIDTH LENGTH PER FOOT MATERIAL (TUBE SIDE)
Cooling CoilsMAX. STD. OPERATING
CONDITIONSFINNED FINNED FINS TUBE PSI TEMP (F)
CHARACTERISTICS ROWS WIDTH LENGTH PER FOOT MATERIAL (TUBE SIDE)
MAX. STD. OPERATING CONDITIONS
FINNED FINNED FINS TUBE PSI TEMP (F)CHARACTERISTICS ROWS WIDTH LENGTH PER FOOT MATERIAL (TUBE SIDE)
P4
WA
W
TT
T ST
NNS
A
WATEROUT
WATERIN
WC
(A)
(N)
(NS)
H
WL
AIRFLOW
WATERIN
WATEROUT
AIRFLOW
WATERIN
WATEROUT
DL
AIRFLOW
WATERIN
WATEROUT
D
WATERIN
WATEROUT
AIR FLOWP8
WATEROUT
AIRFLOW
WATERIN
WATERIN
WATEROUT
AIRFLOW
P2
WATERIN
WATEROUT
AIRFLOW
K
WATERIN
WATEROUT
AIRFLOW
W
REFRIGERANTLIQUID IN
REFRIGERANTGAS OUT
FD
AIRFLOW
AIRFLOW
REFRIGERANTLIQUID IN
REFRIGERANTLIQUID IN
REFRIGERANTGAS OUT
REFRIGERANTGAS OUT
F
AIRFLOW
WATERIN
WATEROUT
LL
AIRFLOW
WATERIN
WATEROUT
AIRFLOW WATER
IN
WATEROUT
AIRFLOW
WATERIN
WATEROUT
(DD)DDWD
(WD)
DL
WL
• DRAINABLE AT HEADER 1* 6, 9, 12, 18 12"-168" ALUMINUM COPPER 200 325 (1-ROW)• LOW GPM 24, 30, 33" 80-168 5⁄8" OD 200 220 (2-ROW)• ALTERNATIVE-TUBE FEED .020"• HOT WATER .024"
.035"2 12, 18, 24, COPPER RED BRASS 200 388 (1-ROW)
30, 33"" 96-168 .049" 200 220 (2-ROW)
• DRAINABLE AT HEADER 1 CAST IRON HDR. 12"-168" ALUMINUM COPPER• ONE-ROW 12, 18, 24 80-168 5⁄8" OD• SAME-END CONNECTION 30, 33" .020"• HOT WATER .024"
COPPER HDR .035"36, 42, 48" COPPER 200 250
96-168 RED BRASS.049"
(CAST IRONHDR ONLY)
• GENERAL PURPOSE 1* 6, 9, 12, 18 ALUMINUM COPPER• DRAINABLE AT HEADER 24, 30, 33" 80-168 5⁄8" OD 200 325 (1-ROW)• FULL-ROW SERPENTINE .020" 200 220 (2-ROW)• HOT WATER .024"
.035"2 (CAST IRON HDR) 12"-168" COPPER RED BRASS 200 388 (1-ROW)
12, 18, 24 96-168 .049" 200 220 (2-ROW)30, 33"
(COPPER HDR)36, 42, 48, 54"
• LOW GPM 1 12, 18 ALUMINUM COPPER• COMMON DUCT COIL 24, 30" 80-168 5⁄8" OD 225 250• TWO-TUBE FEED .020"• HOT WATER .024"
.035" 275 3502 9, 12, 18 12"-96" COPPER RED BRASS
24, 30, 33" 96-168 .049" 350 400
• LOW GPM OR MODERATE 1 6, 9, 12 (T) 6"-72" ALUMINUM COPPER WATER 200 250STEAM PRESSURES 15, 18" 80, 110, 150 5⁄8" OD STEAM 100 400
• COMMON DUCT COILS (ST) 6”-42” .020".024"
• T HAS STANDARD CASING. COPPER 035" WATER 275 350• ST HAS SLIP FLANGE 96, 110, 144 STEAM 350 400
CASING FOR QUICK FIT-UP• HOT WATER OR STEAM 2 RED BRASS WATER 350 400
.049" STEAM 400 450
• GENERAL PURPOSE 2, 3, 4, 6 CAST IRON HDR 12"-168" ALUMINUM COPPER 200 220• DRAINABLE AT HEADER 8, 10, 12 12, 18, 24, 80-168 5⁄8" OD• FULL-ROW SERPENTINE 30, 33’’ .020"• CHILLED WATER .024"
.035"
COPPER HDR 12"-168" COPPER RED BRASS36, 42, 48, 54" 96-168 .049"
• CLEANABLE 2, 4, 6 12, 18, 24 12"-168" ALUMINUM COPPER 200 220• DRAINABLE AT EACH ROW 8, 10, 12 30, 33" 80-168 5⁄8" OD• FULL-ROW SERPENTINE .020"• CHILLED WATER .024"
.035"3*
COPPER RED BRASS96-168 .049"
• LOW GPM 2, 4, 6 12, 18 12"-120" ALUMINUM COPPER 200 220• TWO-TUBE FEED 24, 30" 80-168 5⁄8" OD• CHILLED WATER .020"
.024"
.035"
COPPER RED BRASS96-168 .049"
• LOW GPM 2, 4 12, 18 12"-120" ALUMINUM COPPER 200 220• FOUR-TUBE FEED 6, 8 24, 30" 80-168 5⁄8" OD• CHILLED WATER .020"
.024"
.035"
COPPER RED BRASS96-168 .049"
• LOW GPM 4, 8 18, 24 18"-120 ALUMINUM COPPER 200 220• EIGHT-TUBE FEED 30" 80-168 5⁄8" OD• CHILLED WATER .020"
.024"
.035"
COPPER RED BRASS96-168 .049"
• DRAINABLE AT EACH ROW 4, 6, 8 12, 18, 24 12"-168" ALUMINUM COPPER 200 220• FULL-ROW SERPENTINE 10, 12 30, 33" 80-168 5⁄8" OD• CHILLED WATER .020"
.024"
.035"3*
COPPER RED BRASS96-168 .049"
• DRAINABLE AT EACH ROW 4,8,12 CAST IRON HDR 18"-168" ALUMINUM COPPER 200 220• HIGH GPM 18, 24, 80-168 5⁄8" OD• LOW WATER PRESSURE DROP 6, 10* 30, 33’’ .020"• OPPOSITE-END CONNECTIONS .024"
ON 6 & 10 ROWS .035"• DUAL-ROW SERPENTINE• CHILLED WATER• DRAINABLE AT HEADER• HIGH GPM• LOW WATER PR ESSURE DROP 6, 8 CAST IRON HDR COPPER RED BRASS• SAME-END CONNECTIONS 10, 12 18,24, 96-168 .049"
ON 6 & 10 ROWS 30,33"• DUAL-ROW SERPENTINE COPPER HDR• CHILLED WATER 36, 42, 48, 54"
• GENERAL PURPOSE 2, 4 12, 18, 24 12"-168" ALUMINUM COPPER 200 220• FULL-ROW SERPENTINE 6, 8 30, 33, 36, 1⁄2" OD• CHILLED WATER 42, 48, 54" .016"
DELTA-FLO E72-168 .025"
DELTA-FLO H84-168
• DRAINABLE AT HEADER 2, 4, 6 12, 18, 24, 12"-168" ALUMINUM COPPER 200 220• FULL-ROW SERPENTINE 30, 33, 36 1⁄2" OD• CHILLED WATER 42, 48, 54" .016"
DELTA-FLO E72-168 .025"
DELTA-FLO H84-168
• DRAINABLE AT HEADER 4, 6, 8 18, 24, 30 18"-168" ALUMINUM COPPER 200 220• HIGH GPM 33, 36, 42 1⁄2" OD• LOW WATER PRESSURE DROP 48, 54" .016"• DUAL-ROW SERPENTINE DELTA-FLO E• CHILLED WATER 72-168 .025"
DELTA-FLO H84-168
• REFRIGERANT 2, 3, 4 12, 18, 24 12"-168" ALUMINUM COPPER 300• CIRCUITING AVAILABLE: 6,8 30, 33" 80-168 5⁄8" OD
STANDARD .020"HORIZONTAL SPLIT COPPER .024"VERTICAL SPLIT 96-168
• REFRIGERANT 4, 6 18, 24, 30 18"-168" ALUMINUM COPPER 300• CIRCUITING AVAILABLE: 33, 36, 42 1⁄2" OD
STANDARD 48" .016"HORIZONTAL SPLIT DELTA-FLO EVERTICAL SPLIT 72-168 .025"INTERTWINED
DELTA-FLO H84-168
• UNMODULATED STEAM TYPE 1* 6, 9, 12, 12"-120" ALUMINUM COPPER 100 400• FULL-ROW FEED 18, 24, 30 80-168 5⁄8" OD• STEAM 33’’ .020"
COPPER .024"96-168 .035"
RED BRASS.049" 200 400
• MODULATING STEAM TYPE 1* 12, 18, 24 12"-144" ALUMINUM COPPER• STEAM DISTRIBUTING TYPE 30, 33 42-132 1" OD 100 400• FULL-ROW FEED 30,33" .031"• OPPOSITE-END CONNECTIONS
• SAME-END CONNECTIONS COPPER RED BRASS• STEAM 1 42-132 .049" 200 400
• REFRIGERANT 1,2 12, 18, 24, 24"-168" ALUMINUM COPPER 300• 1-100% HEAT RECOVERY 3,4 30, 33, 36 80-168 5⁄8" OD• MULTIPLE-COMPRESSOR 6 42, 48" .020"
CIRCUITS 54 (2-6 ROW ONLY)
• GENERAL PURPOSE 2 12, 18, 24 12"-168" ALUMINUM COPPER 200 220• FULL-ROW SERPENTINE 30, 33, 36 1⁄2" OD• HOT WATER 42, 48, 54" .016"
DELTA-FLO E72-180 .025"
DELTA-FLO H84-180
• DRAINABLE AT HEADER 2 12,18,24 12"-168" ALUMINUM COPPER 200 220• FULL-ROW SERPENTINE 30, 33, 36 DELTA-FLO E 1⁄2" OD • HOT WATER 42, 48, 54" 72-180 .016"
DELTA-FLO H84-180 .025"
WATERIN
WATEROUT
AIRFLOW
WATERIN
WATEROUT
WATERIN
WATEROUT
WATERIN
WATEROUT
AIRFLOW
REFRIGERANTGAS IN
REFRIGERANTGAS/ LIQUID
OUT
STEAMIN
CONDENSATEOUT
STEAMIN
CONDENSATEOUT
Notes:
1. Turbulators are available in water coils to increase capacities at low fluid flow rates. 2. Special material construction, operating pressures and temperatures are available. 3. All chilled water coils can be used in hot water applications. 4. Drain and vent connections are standard on all water coils. 5. All finned lengths are available in one inch increments (except T and ST coils). 6. All fin spacings are available in one fin per foot increments.
*Opposite-end connection. †ARI certification does not exist for type H coils.
Heating CoilsMAX. STD. OPERATING
CONDITIONSFINNED FINNED FINS TUBE PSI TEMP (F)
CHARACTERISTICS ROWS WIDTH LENGTH PER FOOT MATERIAL (TUBE SIDE)
MAX. STD. OPERATING CONDITIONS
FINNED FINNED FINS TUBE PSI TEMP (F)CHARACTERISTICS ROWS WIDTH LENGTH PER FOOT MATERIAL (TUBE SIDE)
Cooling CoilsMAX. STD. OPERATING
CONDITIONSFINNED FINNED FINS TUBE PSI TEMP (F)
CHARACTERISTICS ROWS WIDTH LENGTH PER FOOT MATERIAL (TUBE SIDE)
MAX. STD. OPERATING CONDITIONS
FINNED FINNED FINS TUBE PSI TEMP (F)CHARACTERISTICS ROWS WIDTH LENGTH PER FOOT MATERIAL (TUBE SIDE)
P4
WA
W
TT
T ST
NNS
A
WATEROUT
WATERIN
WC
(A)
(N)
(NS)
H
WL
AIRFLOW
WATERIN
WATEROUT
AIRFLOW
WATERIN
WATEROUT
DL
AIRFLOW
WATERIN
WATEROUT
D
WATERIN
WATEROUT
AIR FLOWP8
WATEROUT
AIRFLOW
WATERIN
WATERIN
WATEROUT
AIRFLOW
P2
WATERIN
WATEROUT
AIRFLOW
K
WATERIN
WATEROUT
AIRFLOW
W
REFRIGERANTLIQUID IN
REFRIGERANTGAS OUT
FD
AIRFLOW
AIRFLOW
REFRIGERANTLIQUID IN
REFRIGERANTLIQUID IN
REFRIGERANTGAS OUT
REFRIGERANTGAS OUT
F
AIRFLOW
WATERIN
WATEROUT
LL
AIRFLOW
WATERIN
WATEROUT
AIRFLOW WATER
IN
WATEROUT
AIRFLOW
WATERIN
WATEROUT
(DD)DDWD
(WD)
DL
WL
• DRAINABLE AT HEADER 1* 6, 9, 12, 18 12"-168" ALUMINUM COPPER 200 325 (1-ROW)• LOW GPM 24, 30, 33" 80-168 5⁄8" OD 200 220 (2-ROW)• ALTERNATIVE-TUBE FEED .020"• HOT WATER .024"
.035"2 12, 18, 24, COPPER RED BRASS 200 388 (1-ROW)
30, 33"" 96-168 .049" 200 220 (2-ROW)
• DRAINABLE AT HEADER 1 CAST IRON HDR. 12"-168" ALUMINUM COPPER• ONE-ROW 12, 18, 24 80-168 5⁄8" OD• SAME-END CONNECTION 30, 33" .020"• HOT WATER .024"
COPPER HDR .035"36, 42, 48" COPPER 200 250
96-168 RED BRASS.049"
(CAST IRONHDR ONLY)
• GENERAL PURPOSE 1* 6, 9, 12, 18 ALUMINUM COPPER• DRAINABLE AT HEADER 24, 30, 33" 80-168 5⁄8" OD 200 325 (1-ROW)• FULL-ROW SERPENTINE .020" 200 220 (2-ROW)• HOT WATER .024"
.035"2 (CAST IRON HDR) 12"-168" COPPER RED BRASS 200 388 (1-ROW)
12, 18, 24 96-168 .049" 200 220 (2-ROW)30, 33"
(COPPER HDR)36, 42, 48, 54"
• LOW GPM 1 12, 18 ALUMINUM COPPER• COMMON DUCT COIL 24, 30" 80-168 5⁄8"OD 225 250• TWO-TUBE FEED .020"• HOT WATER .024"
.035" 275 3502 9, 12, 18 12"-96" COPPER RED BRASS
24, 30, 33" 96-168 .049" 350 400
• LOW GPM OR MODERATE 1 6, 9, 12 (T) 6"-72" ALUMINUM COPPER WATER 200 250STEAM PRESSURES 15, 18" 80, 110, 150 5⁄8"OD STEAM 100 400
• COMMON DUCT COILS (ST) 6”-42” .020".024"
• T HAS STANDARD CASING. COPPER 035" WATER 275 350• ST HAS SLIP FLANGE 96, 110, 144 STEAM 350 400
CASING FOR QUICK FIT-UP• HOT WATER OR STEAM 2 RED BRASS WATER 350 400
.049" STEAM 400 450
• GENERAL PURPOSE 2, 3, 4, 6 CAST IRON HDR 12"-168" ALUMINUM COPPER 200 220• DRAINABLE AT HEADER 8, 10, 12 12, 18, 24, 80-168 5⁄8" OD• FULL-ROW SERPENTINE 30, 33’’ .020"• CHILLED WATER .024"
.035"
COPPER HDR 12"-168" COPPER RED BRASS36, 42, 48, 54" 96-168 .049"
• CLEANABLE 2, 4, 6 12, 18, 24 12"-168" ALUMINUM COPPER 200 220• DRAINABLE AT EACH ROW 8, 10, 12 30, 33" 80-168 5⁄8" OD• FULL-ROW SERPENTINE .020"• CHILLED WATER .024"
.035"3*
COPPER RED BRASS96-168 .049"
• LOW GPM 2, 4, 6 12, 18 12"-120" ALUMINUM COPPER 200 220• TWO-TUBE FEED 24, 30" 80-168 5⁄8" OD• CHILLED WATER .020"
.024"
.035"
COPPER RED BRASS96-168 .049"
• LOW GPM 2, 4 12, 18 12"-120" ALUMINUM COPPER 200 220• FOUR-TUBE FEED 6, 8 24, 30" 80-168 5⁄8" OD• CHILLED WATER .020"
.024"
.035"
COPPER RED BRASS96-168 .049"
• LOW GPM 4, 8 18, 24 18"-120 ALUMINUM COPPER 200 220• EIGHT-TUBE FEED 30" 80-168 5⁄8" OD• CHILLED WATER .020"
.024"
.035"
COPPER RED BRASS96-168 .049"
• DRAINABLE AT EACH ROW 4, 6, 8 12, 18, 24 12"-168" ALUMINUM COPPER 200 220• FULL-ROW SERPENTINE 10, 12 30, 33" 80-168 5⁄8" OD• CHILLED WATER .020"
.024"
.035"3*
COPPER RED BRASS96-168 .049"
• DRAINABLE AT EACH ROW 4,8,12 CAST IRON HDR 18"-168" ALUMINUM COPPER 200 220• HIGH GPM 18, 24, 80-168 5⁄8" OD• LOW WATER PRESSURE DROP 6, 10* 30, 33’’ .020"• OPPOSITE-END CONNECTIONS .024"
ON 6 & 10 ROWS .035"• DUAL-ROW SERPENTINE• CHILLED WATER• DRAINABLE AT HEADER• HIGH GPM• LOW WATER PR ESSURE DROP 6, 8 CAST IRON HDR COPPER RED BRASS• SAME-END CONNECTIONS 10, 12 18,24, 96-168 .049"
ON 6 & 10 ROWS 30,33"• DUAL-ROW SERPENTINE COPPER HDR• CHILLED WATER 36, 42, 48, 54"
• GENERAL PURPOSE 2, 4 12, 18, 24 12"-168" ALUMINUM COPPER 200 220• FULL-ROW SERPENTINE 6, 8 30, 33, 36, 1⁄2" OD• CHILLED WATER 42, 48, 54" .016"
DELTA-FLO E72-168 .025"
DELTA-FLO H84-168
• DRAINABLE AT HEADER 2, 4, 6 12, 18, 24, 12"-168" ALUMINUM COPPER 200 220• FULL-ROW SERPENTINE 30, 33, 36 1⁄2" OD• CHILLED WATER 42, 48, 54" .016"
DELTA-FLO E72-168 .025"
DELTA-FLO H84-168
• DRAINABLE AT HEADER 4, 6, 8 18, 24, 30 18"-168" ALUMINUM COPPER 200 220• HIGH GPM 33, 36, 42 1⁄2" OD• LOW WATER PRESSURE DROP 48, 54" .016"• DUAL-ROW SERPENTINE DELTA-FLO E• CHILLED WATER 72-168 .025"
DELTA-FLO H84-168
• REFRIGERANT 2, 3, 4 12, 18, 24 12"-168" ALUMINUM COPPER 300• CIRCUITING AVAILABLE: 6,8 30, 33" 80-168 5⁄8" OD
STANDARD .020"HORIZONTAL SPLIT COPPER .024"VERTICAL SPLIT 96-168
• REFRIGERANT 4, 6 18, 24, 30 18"-168" ALUMINUM COPPER 300• CIRCUITING AVAILABLE: 33, 36, 42 1⁄2" OD
STANDARD 48" .016"HORIZONTAL SPLIT DELTA-FLO EVERTICAL SPLIT 72-168 .025"INTERTWINED
DELTA-FLO H84-168
• UNMODULATED STEAM TYPE 1* 6, 9, 12, 12"-120" ALUMINUM COPPER 100 400• FULL-ROW FEED 18, 24, 30 80-168 5⁄8" OD• STEAM 33’’ .020"
COPPER .024"96-168 .035"
RED BRASS.049" 200 400
• MODULATING STEAM TYPE 1* 12, 18, 24 12"-144" ALUMINUM COPPER• STEAM DISTRIBUTING TYPE 30, 33 42-132 1" OD 100 400• FULL-ROW FEED 30,33" .031"• OPPOSITE-END CONNECTIONS
• SAME-END CONNECTIONS COPPER RED BRASS• STEAM 1 42-132 .049" 200 400
• REFRIGERANT 1,2 12, 18, 24, 24"-168" ALUMINUM COPPER 300• 1-100% HEAT RECOVERY 3,4 30, 33, 36 80-168 5⁄8" OD• MULTIPLE-COMPRESSOR 6 42, 48" .020"
CIRCUITS 54 (2-6 ROW ONLY)
• GENERAL PURPOSE 2 12, 18, 24 12"-168" ALUMINUM COPPER 200 220• FULL-ROW SERPENTINE 30, 33, 36 1⁄2" OD• HOT WATER 42, 48, 54" .016"
DELTA-FLO E72-180 .025"
DELTA-FLO H84-180
• DRAINABLE AT HEADER 2 12,18,24 12"-168" ALUMINUM COPPER 200 220• FULL-ROW SERPENTINE 30, 33, 36 DELTA-FLO E 1⁄2" OD • HOT WATER 42, 48, 54" 72-180 .016"
DELTA-FLO H84-180 .025"
WATERIN
WATEROUT
AIRFLOW
WATERIN
WATEROUT
WATERIN
WATEROUT
WATERIN
WATEROUT
AIRFLOW
REFRIGERANTGAS IN
REFRIGERANTGAS/ LIQUID
OUT
STEAMIN
CONDENSATEOUT
STEAMIN
CONDENSATEOUT
Notes:
1. Turbulators are available in water coils to increase capacities at low fluid flow rates. 2. Special material construction, operating pressures and temperatures are available. 3. All chilled water coils can be used in hot water applications. 4. Drain and vent connections are standard on all water coils. 5. All finned lengths are available in one inch increments (except T and ST coils). 6. All fin spacings are available in one fin per foot increments.
*Opposite-end connection. †ARI certification does not exist for type H coils.
Heating CoilsMAX. STD. OPERATING
CONDITIONSFINNED FINNED FINS TUBE PSI TEMP (F)
CHARACTERISTICS ROWS WIDTH LENGTH PER FOOT MATERIAL (TUBE SIDE)
MAX. STD. OPERATING CONDITIONS
FINNED FINNED FINS TUBE PSI TEMP (F)CHARACTERISTICS ROWS WIDTH LENGTH PER FOOT MATERIAL (TUBE SIDE)
Cooling CoilsMAX. STD. OPERATING
CONDITIONSFINNED FINNED FINS TUBE PSI TEMP (F)
CHARACTERISTICS ROWS WIDTH LENGTH PER FOOT MATERIAL (TUBE SIDE)
MAX. STD. OPERATING CONDITIONS
FINNED FINNED FINS TUBE PSI TEMP (F)CHARACTERISTICS ROWS WIDTH LENGTH PER FOOT MATERIAL (TUBE SIDE)
P4
WA
W
TT
T ST
NNS
A
WATEROUT
WATERIN
WC
(A)
(N)
(NS)
H
WL
AIRFLOW
WATERIN
WATEROUT
AIRFLOW
WATERIN
WATEROUT
DL
AIRFLOW
WATERIN
WATEROUT
D
WATERIN
WATEROUT
AIR FLOWP8
WATEROUT
AIRFLOW
WATERIN
WATERIN
WATEROUT
AIRFLOW
P2
WATERIN
WATEROUT
AIRFLOW
K
WATERIN
WATEROUT
AIRFLOW
W
REFRIGERANTLIQUID IN
REFRIGERANTGAS OUT
FD
AIRFLOW
AIRFLOW
REFRIGERANTLIQUID IN
REFRIGERANTLIQUID IN
REFRIGERANTGAS OUT
REFRIGERANTGAS OUT
F
AIRFLOW
WATERIN
WATEROUT
LL
AIRFLOW
WATERIN
WATEROUT
AIRFLOW WATER
IN
WATEROUT
AIRFLOW
WATERIN
WATEROUT
(DD)DDWD
(WD)
DL
WL
• DRAINABLE AT HEADER 1* 6, 9, 12, 18 12"-168" ALUMINUM COPPER 200 325 (1-ROW)• LOW GPM 24, 30, 33" 80-168 5⁄8" OD 200 220 (2-ROW)• ALTERNATIVE-TUBE FEED .020"• HOT WATER .024"
.035"2 12, 18, 24, COPPER RED BRASS 200 388 (1-ROW)
30, 33"" 96-168 .049" 200 220 (2-ROW)
• DRAINABLE AT HEADER 1 CAST IRON HDR. 12"-168" ALUMINUM COPPER• ONE-ROW 12, 18, 24 80-168 5⁄8" OD• SAME-END CONNECTION 30, 33" .020"• HOT WATER .024"
COPPER HDR .035"36, 42, 48" COPPER 200 250
96-168 RED BRASS.049"
(CAST IRONHDR ONLY)
• GENERAL PURPOSE 1* 6, 9, 12, 18 ALUMINUM COPPER• DRAINABLE AT HEADER 24, 30, 33" 80-168 5⁄8" OD 200 325 (1-ROW)• FULL-ROW SERPENTINE .020" 200 220 (2-ROW)• HOT WATER .024"
.035"2 (CAST IRON HDR) 12"-168" COPPER RED BRASS 200 388 (1-ROW)
12, 18, 24 96-168 .049" 200 220 (2-ROW)30, 33"
(COPPER HDR)36, 42, 48, 54"
• LOW GPM 1 12, 18 ALUMINUM COPPER• COMMON DUCT COIL 24, 30" 80-168 5⁄8" OD 225 250• TWO-TUBE FEED .020"• HOT WATER .024"
.035" 275 3502 9, 12, 18 12"-96" COPPER RED BRASS
24, 30, 33" 96-168 .049" 350 400
• LOW GPM OR MODERATE 1 6, 9, 12 (T) 6"-72" ALUMINUM COPPER WATER 200 250STEAM PRESSURES 15, 18" 80, 110, 150 5⁄8" OD STEAM 100 400
• COMMON DUCT COILS (ST) 6”-42” .020".024"
• T HAS STANDARD CASING. COPPER 035" WATER 275 350• ST HAS SLIP FLANGE 96, 110, 144 STEAM 350 400
CASING FOR QUICK FIT-UP• HOT WATER OR STEAM 2 RED BRASS WATER 350 400
.049" STEAM 400 450
• GENERAL PURPOSE 2, 3, 4, 6 CAST IRON HDR 12"-168" ALUMINUM COPPER 200 220• DRAINABLE AT HEADER 8, 10, 12 12, 18, 24, 80-168 5⁄8" OD• FULL-ROW SERPENTINE 30, 33’’ .020"• CHILLED WATER .024"
.035"
COPPER HDR 12"-168" COPPER RED BRASS36, 42, 48, 54" 96-168 .049"
• CLEANABLE 2, 4, 6 12, 18, 24 12"-168" ALUMINUM COPPER 200 220• DRAINABLE AT EACH ROW 8, 10, 12 30, 33" 80-168 5⁄8" OD• FULL-ROW SERPENTINE .020"• CHILLED WATER .024"
.035"3*
COPPER RED BRASS96-168 .049"
• LOW GPM 2, 4, 6 12, 18 12"-120" ALUMINUM COPPER 200 220• TWO-TUBE FEED 24, 30" 80-168 5⁄8" OD• CHILLED WATER .020"
.024"
.035"
COPPER RED BRASS96-168 .049"
• LOW GPM 2, 4 12, 18 12"-120" ALUMINUM COPPER 200 220• FOUR-TUBE FEED 6, 8 24, 30" 80-168 5⁄8" OD• CHILLED WATER .020"
.024"
.035"
COPPER RED BRASS96-168 .049"
• LOW GPM 4, 8 18, 24 18"-120 ALUMINUM COPPER 200 220• EIGHT-TUBE FEED 30" 80-168 5⁄8" OD• CHILLED WATER .020"
.024"
.035"
COPPER RED BRASS96-168 .049"
• DRAINABLE AT EACH ROW 4, 6, 8 12, 18, 24 12"-168" ALUMINUM COPPER 200 220• FULL-ROW SERPENTINE 10, 12 30, 33" 80-168 5⁄8" OD• CHILLED WATER .020"
.024"
.035"3*
COPPER RED BRASS96-168 .049"
• DRAINABLE AT EACH ROW 4,8,12 CAST IRON HDR 18"-168" ALUMINUM COPPER 200 220• HIGH GPM 18, 24, 80-168 5⁄8" OD• LOW WATER PRESSURE DROP 6, 10* 30, 33’’ .020"• OPPOSITE-END CONNECTIONS .024"
ON 6 & 10 ROWS .035"• DUAL-ROW SERPENTINE• CHILLED WATER• DRAINABLE AT HEADER• HIGH GPM• LOW WATER PR ESSURE DROP 6, 8 CAST IRON HDR COPPER RED BRASS• SAME-END CONNECTIONS 10, 12 18,24, 96-168 .049"
ON 6 & 10 ROWS 30,33"• DUAL-ROW SERPENTINE COPPER HDR• CHILLED WATER 36, 42, 48, 54"
• GENERAL PURPOSE 2, 4 12, 18, 24 12"-168" ALUMINUM COPPER 200 220• FULL-ROW SERPENTINE 6, 8 30, 33, 36, 1⁄2" OD• CHILLED WATER 42, 48, 54" .016"
DELTA-FLO E72-168 .025"
DELTA-FLO H84-168
• DRAINABLE AT HEADER 2, 4, 6 12, 18, 24, 12"-168" ALUMINUM COPPER 200 220• FULL-ROW SERPENTINE 30, 33, 36 1⁄2" OD• CHILLED WATER 42, 48, 54" .016"
DELTA-FLO E72-168 .025"
DELTA-FLO H84-168
• DRAINABLE AT HEADER 4, 6, 8 18, 24, 30 18"-168" ALUMINUM COPPER 200 220• HIGH GPM 33, 36, 42 1⁄2" OD• LOW WATER PRESSURE DROP 48, 54" .016"• DUAL-ROW SERPENTINE DELTA-FLO E• CHILLED WATER 72-168 .025"
DELTA-FLO H84-168
• REFRIGERANT 2, 3, 4 12, 18, 24 12"-168" ALUMINUM COPPER 300• CIRCUITING AVAILABLE: 6,8 30, 33" 80-168 5⁄8" OD
STANDARD .020"HORIZONTAL SPLIT COPPER .024"VERTICAL SPLIT 96-168
• REFRIGERANT 4, 6 18, 24, 30 18"-168" ALUMINUM COPPER 300• CIRCUITING AVAILABLE: 33, 36, 42 1⁄2" OD
STANDARD 48" .016"HORIZONTAL SPLIT DELTA-FLO EVERTICAL SPLIT 72-168 .025"INTERTWINED
DELTA-FLO H84-168
• UNMODULATED STEAM TYPE 1* 6, 9, 12, 12"-120" ALUMINUM COPPER 100 400• FULL-ROW FEED 18, 24, 30 80-168 5⁄8" OD• STEAM 33’’ .020"
COPPER .024"96-168 .035"
RED BRASS.049" 200 400
• MODULATING STEAM TYPE 1* 12, 18, 24 12"-144" ALUMINUM COPPER• STEAM DISTRIBUTING TYPE 30, 33 42-132 1" OD 100 400• FULL-ROW FEED 30,33" .031"• OPPOSITE-END CONNECTIONS
• SAME-END CONNECTIONS COPPER RED BRASS• STEAM 1 42-132 .049" 200 400
• REFRIGERANT 1,2 12, 18, 24, 24"-168" ALUMINUM COPPER 300• 1-100% HEAT RECOVERY 3,4 30, 33, 36 80-168 5⁄8" OD• MULTIPLE-COMPRESSOR 6 42, 48" .020"
CIRCUITS 54 (2-6 ROW ONLY)
• GENERAL PURPOSE 2 12, 18, 24 12"-168" ALUMINUM COPPER 200 220• FULL-ROW SERPENTINE 30, 33, 36 1⁄2" OD• HOT WATER 42, 48, 54" .016"
DELTA-FLO E72-180 .025"
DELTA-FLO H84-180
• DRAINABLE AT HEADER 2 12,18,24 12"-168" ALUMINUM COPPER 200 220• FULL-ROW SERPENTINE 30, 33, 36 DELTA-FLO E 1⁄2" OD • HOT WATER 42, 48, 54" 72-180 .016"
DELTA-FLO H84-180 .025"
WATERIN
WATEROUT
AIRFLOW
WATERIN
WATEROUT
WATERIN
WATEROUT
WATERIN
WATEROUT
AIRFLOW
REFRIGERANTGAS IN
REFRIGERANTGAS/ LIQUID
OUT
STEAMIN
CONDENSATEOUT
STEAMIN
CONDENSATEOUT
Notes:
1. Turbulators are available in water coils to increase capacities at low fluid flow rates. 2. Special material construction, operating pressures and temperatures are available. 3. All chilled water coils can be used in hot water applications. 4. Drain and vent connections are standard on all water coils. 5. All finned lengths are available in one inch increments (except T and ST coils). 6. All fin spacings are available in one fin per foot increments.
*Opposite-end connection. †ARI certification does not exist for type H coils.
Heating CoilsMAX. STD. OPERATING
CONDITIONSFINNED FINNED FINS TUBE PSI TEMP (F)
CHARACTERISTICS ROWS WIDTH LENGTH PER FOOT MATERIAL (TUBE SIDE)
MAX. STD. OPERATING CONDITIONS
FINNED FINNED FINS TUBE PSI TEMP (F)CHARACTERISTICS ROWS WIDTH LENGTH PER FOOT MATERIAL (TUBE SIDE)
Cooling CoilsMAX. STD. OPERATING
CONDITIONSFINNED FINNED FINS TUBE PSI TEMP (F)
CHARACTERISTICS ROWS WIDTH LENGTH PER FOOT MATERIAL (TUBE SIDE)
MAX. STD. OPERATING CONDITIONS
FINNED FINNED FINS TUBE PSI TEMP (F)CHARACTERISTICS ROWS WIDTH LENGTH PER FOOT MATERIAL (TUBE SIDE)
P4
WA
W
TT
T ST
NNS
A
WATEROUT
WATERIN
WC
(A)
(N)
(NS)
H
WL
AIRFLOW
WATERIN
WATEROUT
AIRFLOW
WATERIN
WATEROUT
DL
AIRFLOW
WATERIN
WATEROUT
D
WATERIN
WATEROUT
AIR FLOWP8
WATEROUT
AIRFLOW
WATERIN
WATERIN
WATEROUT
AIRFLOW
P2
WATERIN
WATEROUT
AIRFLOW
K
WATERIN
WATEROUT
AIRFLOW
W
REFRIGERANTLIQUID IN
REFRIGERANTGAS OUT
FD
AIRFLOW
AIRFLOW
REFRIGERANTLIQUID IN
REFRIGERANTLIQUID IN
REFRIGERANTGAS OUT
REFRIGERANTGAS OUT
F
AIRFLOW
WATERIN
WATEROUT
LL
AIRFLOW
WATERIN
WATEROUT
AIRFLOW WATER
IN
WATEROUT
AIRFLOW
WATERIN
WATEROUT
(DD)DDWD
(WD)
DL
WL
Delta-Flo™ Fin Design
The Delta-Flo coil features astaggered 1/2-inch tube pattern andunique fin design allowing for lowairside pressure drop with highcapacity for lower gpmapplications. With staggered tubesand its unique fin configuration,the Delta-Flo coil is one of the mostefficient half-inch coils available inthe industry. Delta-Flo coils areavailable in the original Delta-FloE
®
fin surface and the new Delta-FloH®
enhanced fin surface. Delta-Flo Hfins offer increased capacities andhigher moisture carryover limitswhen compared to the originalDelta-Flo E fins. Delta-Flo E andDelta-Flo H are available inaluminum fins.
Prima-Flo®Fin Design
The Prima-Flo coil features aparallel 5/8-inch tube pattern. Theenergy efficient Prima-Flo Efinsurface is designed to decreasestatic pressure loss through thecoil. This fin is ideal for systemswhere airside pressure drop is amajor concern. Reducing pressuredrop through the coil results inlower fan brake horsepower andsystem energy savings. Prima-Flocoils are available in the originalPrima-Flo Efin surface and the newPrima-Flo Henhanced fin surface.Prima-Flo Hfins offer increasedcapacities and moisture carryoverlimits when compared to theoriginal Prima-Flo Efins. Prima-Flo Eand Prima-Flo Hareavailable in aluminum fins.
Sigma-Flo® Fin Design
The Sigma-Flo coil is available in a5/8-inch and 1-inch parallel tubepattern. The Sigma-Flo fin isdesigned to maximize heat transferand minimize coil size. The 5/8-inch Sigma-Flo tube pattern is availablewith COPPER fins only. The 1-inchSigma-Flo tube pattern for use withsteam coils is available withaluminum or copper fins.
Better Performance Using
Trane IVS
Infinitely variable fin spacing (IVS)gives the designer many ways toselect the right coil for a particularjob.
IVS fins are available on all coil finsurfaces for coil selections tailoredto application needs. This flexibilityis important since coil heating orcooling loads can be matchedmore precisely than traditional"fixed" fin spacing. For example, a Delta-Flo Ecooling coil can beselected from 72 fins per foot to168 fins per foot in one-finincrements.
In many cases IVS fins will allowdesigners to reduce the number offins required to meet coil loads.Fewer fins can result in lowerairside pressure drops and lowerfan brake horsepower, savingvaluable energy dollars. Reducingthe fan BHP may allow theselection of a smaller fan motor ora smaller air handler, savingadditional dollars.
Using IVS and the five fin surfaceoptions, the designer has moreflexibility than ever to design andselect coils.
Computerized Selection
Programs
For quick, easy and accurate coilselections, as well as greaterflexibility in design decisions, TheTrane Company has developedcomputerized selection programs.These programs are available fromyour local Trane office.
Coils can be selected for thefollowing:
• Chilled Water
• Hot Water
• Steam
• Refrigerant
• Refrigerant Heat Recovery
• Coil Runaround Loop HeatRecovery
Based on initial input conditions,the programs will calculatecapacity, air pressure drop andwater pressure drop for all watercoils and steam pressure drop forsteam coils, including coils withcopper fins or coils requiringheavier tube thicknesses.
Improve system efficiency with 25coil types, five fin surfaces, IVS anda wide selection of refrigerant coilcircuiting options. Since pumpingcosts are typically lower thanairside operating costs, increaseavailable waterflow to reduce finrequirements and airside pressuredrops for fan energy savings.
Heating and
Cooling Coils
Coils for All Comfort,
Commercial and
Industrial Applications
More Coils for More Uses
C.D.S.Network
The Trane Customer DirectService Network™ is acomputerized engineeringdesign service providing time-tested software and access topersonal computer programs.Complete with a communicationspackage to support it, C.D.S.delivers HVAC program updatesand user support instantly.
With the variety of header designfeatures and material flexibility,along with IVS and computerselection programs, Trane provesagain it’s the leader in coiltechnology.
Infinitely Variable Fin Spacing
Delta-Flo™
Prima-Flo®
and
Sigma-Flo®
Unique Design
Energy Efficient
Cost-Effective
© American Standard Inc. 1998
File No. COIL-TS-1 August 1998
Supersedes COIL-TS-1-1189
File No. PL-AH-COIL-000-TS-1-898
Worldwide Applied Systems Group
The Trane Company3600 Pammel Creek RoadLa Crosse, WI 54601-7599www.trane.com
An American Standard CompanySince The Trane Company has a policy of continuous product improvement, it reserves the right to change design and specification without notice.
