8805 Jones Road Suite C104, Houston, TX 77065 * 1-888-861-7351 * www.zuummedia.com ZM61714 8805 Jones Rd. Ste. C104, Houston, X 77065 * 1-888-861-7351 * www.zuummedia.com ZM 032014

HE1LBIR232-P-60M

HDBaseT HDMI Long Range Extender over Single CAT5/6 Cable with Bi-Directional IR, RS232 & PoC The HE1LBIR232-P-60M is using only one cost effective CAT5/6 cable to extend your HDTV display up to 196ft with CAT5 and up to 130ft at 4K2K @30. With high quality uncompressed video it delivers significant value to the entire home and commercial entertainment system and the install convenience of only needing one power supply at ether RX or TX side. Features:

> Extends HDMI, RS232 and IR over one CAT5/6 cable (CAT6 recommended for best results) > Uncompressed high definition video up to full 3D & 4K2K@30 > 1080p 48 bit up to 196ft and 4K2K@30 up to 130ft > Bi-Directional IR selectable by 3.5mm jack at either TX/RX side > IR carrier frequency is pass-thru with signal support 20KHz to 60KHz > Max. Data Rate - 10.2Gbps > Support PoC (Power over Cable) which will power both TX and RX with one power supply from ether side > HDCP & EDID Bypass > CEC support > Auto Equalization > Audio support up to LPCM7.1, Dolby TrueHD, DTS-HD MA

Panel View:

Front Panel TX

 

 

 

1. LED: Power LED, Status LED, Link LED, HDCP LED

(1) Power LED: This LED light always on means unit is on.

(2) Status LED: This LED light is blinking it means function ok.

(3) Link LED: This LED light always on means its ok. (Link Established)

(4) HDCP LED: HDCP ON – the LED light always on

HDCP LED: HDCP OFF – the LED light is blinking Rear Panel TX

 

 

               

2. Latch-locking power jack: Connect to 12V DC power supply

3. RJ45: Plug in a Cat-5/5e/6 cable that needs to be linked to the receiving unit

4. IR Receiver: Infrared 3.5mm socket for plugging in the extension cable of IR receiver

5. IR Blaster: Infrared 3.5mm socket for plugging in the extension cable of IR blaster

6. RS-232(terminal block format): The order of RS-232 pins are TX, RX, GND (from the left side to the right)

7. HDMI IN: Connects to a HDMI source with HDMI male-male cable

8805 Jones Road Suite C104, Houston, TX 77065 * 1-888-861-7351 * www.zuummedia.com ZM61714 8805 Jones Rd. Ste. C104, Houston, X 77065 * 1-888-861-7351 * www.zuummedia.com ZM 032014

Front Panel RX

8. LED: Power LED, Status LED, Link LED, HDCP LED

(1) Power LED: This LED light always on means unit is on.

(2) Status LED: This LED light is blinking it means function ok.

(3) Link LED: This LED light always on means its ok. (Link Established)

(4) HDCP LED: HDCP ON – the LED light always on

HDCP LED: HDCP OFF – the LED light is blinking

Rear Panel RX

9. Latch-locking power jack: Connect to 12V DC power supply

10. RJ45: Plug in a Cat-5/5e/6 cable that needs to be linked to the receiving unit

11. IR Receiver: Infrared 3.5mm socket for plugging in the extension cable of IR receiver

12. IR Blaster: Infrared 3.5mm socket for plugging in the extension cable of IR blaster

13. RS-232(terminal block format): The order of RS-232 pins are TX, RX, GND (from the left side to the right)

14. HDMI OUT: Connects to a HDMI display with HDMI male-male cable

IR Cables:

IR Blaster IR Receiver

NOTE: Incorrect placement of the IR blaster and Receiver may damage the units. Please confirm IR Blaster and IR Receiver are plugged into correct ports before powering up HDMI extenders.

Installation:

1. EIA/TIA-568-B termination (T568B) for Cat-5/5e/6 cables is recommended for better performance

1. Connect a HDMI or DVI source (such as a Blu-ray Disc player) to the transmitting unit

2. Connect a HDMI or DVI display (such as a LCD TV) to the receiving unit

3. Connect IR Blaster/Receiver to both TX and RX units.

4. Connect a Cat-5/5e/6 cable between the transmitting and receiving units.

8805 Jones Road Suite C104, Houston, TX 77065 * 1-888-861-7351 * www.zuummedia.com ZM61714 8805 Jones Rd. Ste. C104, Houston, X 77065 * 1-888-861-7351 * www.zuummedia.com ZM 032014

Model: HE1LBIR232-P-60MT HE1LBIR232-P-60MR Resolution Up to 3D, 4Kx2K@30 Distance CAT5 196ft(60M) 1080p, CAT5 130FT(40M) 4K2K@30 HDMI Connector Type A Power Supply One Regulated 12V/2A for (Poc) Power Consumption 3 Watt (Max) 7 Watt (Max)

Temperature Operation: 35 to 131°F, Storage: -4 to 185°F

Humidity 20 ~ 90% RH (no condensation)

Dimensions - Inches 3.9(w) x 2.9(h) x .6(d) Weight - lbs. .35  

5. Make sure this Cat-5/5e/6 cable is tightly connected and not loose.

6. Plug in 12V DC power supply unit to the power jack of the receiving unit or the transmitting unit

Transmission Range: If connection is through a wall jack, (not recommended) this could limit the full transmission distance between the Transmitter and Receiver Extenders. We only recommended using a straight CAT5/6 cable with RJ45 connections on each end.

Shielded Cable: On most installations it is recommended to use Shielded CAT5/6 cable with properly connected shielded RJ45 connectors. This will prevent video and audio loss due to EMI and other interference from switched lighting and ceiling fans.

Caution:

1. The wiring must be away from any equipment with electromagnetic signal, i.e.: mobile phone, microwave, radio equipment, fluorescent lamp, and high voltage power lines.

2. This device is not network compatible; do not connect via Network to avoid damage.

Package Includes:

Transmitter x 1 piece Receiver x 1 piece Power adapter x 1 piece IR Blaster x 1 piece IR Receiver x 1 piece Mounting brackets x 2 Mounting Screws

Specification: