HARNESS CHECKER BOX.pdf
2
1 of 2 T-junction adaptor for use with the 40-Pin DEUTSCH connector T-junction adaptor for use with the 24-Pin DEUTSCH connector Box 799-601-9320 Component parts of the KIT 799-601-9300 The plate 799-601-9310 is omitted here. Refer to the Section 5) of the Chapter 2. on the next page regarding the plate. Part numbers Q’ty 799-601-9310 1 799-601-9320 1 799-601-9350 1 799-601-9360 1 1. Part numbers 1) 799-601-9360 (T-junction adaptor for use with the 24-Pin DEUTSCH connector) 2) 799-601-9350 (T-junction adaptor for use with the 40-Pin DEUTSCH connector) Note 1. The Part No. of the box connecting to these adaptors is 799-601-9320. (Then above is common with the T-junction adaptors for other DEUTSCH connectors. Refer to SEKN5005) Note 2. When using the T-junction adaptor for use with the 40-Pin DEUTSCH connector, it is necessary to use two boxes of the new box 799-601-9320 and the currently using box 799-601-2600. At this time, apply the plate (Part No.: 799-601-9310) on the current box 799-601-2600. Note 3. For your prompt preparation, we have prepared a kit for the above application with the KIT No. of 799-601-9300. [Component parts of the KIT 799-601-9300] Introduction of the T-junction Adaptor for the 24-Pin and 40-Pin DEUTSCH Connectors Starting from the hydraulic excavators of Model PC58-3, PC78-6 and PC200-7, the controllers with the common name of “NGI controller” are being used. To these controllers, 1 unit of 24-Pin DEUTSCH Connector and 2 units of 40-Pin DEUTSCH Connectors are being connected. This PARTS & SERVICE OPERATION TIPS will introduce the T-junction adaptor for use with these DEUTSCH connectors.
-
Upload
joko-sukariono -
Category
Documents
-
view
7 -
download
1
Transcript of HARNESS CHECKER BOX.pdf
1 of 2
T-junction adaptor for use with the 40-Pin DEUTSCH connector
T-junction adaptor for use with the 24-Pin DEUTSCH connector
Box 799-601-9320
Component parts of the KIT 799-601-9300
The plate 799-601-9310 is omitted here.Refer to the Section 5) of the Chapter 2. on the next page regarding the plate.
Part numbers Q’ty799-601-9310 1799-601-9320 1799-601-9350 1799-601-9360 1
1. Part numbers1) 799-601-9360
(T-junction adaptor for use with the 24-PinDEUTSCH connector)
2) 799-601-9350(T-junction adaptor for use with the 40-PinDEUTSCH connector)
Note 1. The Part No. of the box connecting to theseadaptors is 799-601-9320.(Then above is common with the T-junctionadaptors for other DEUTSCH connectors.Refer to SEKN5005)
Note 2. When using the T-junction adaptor for usewith the 40-Pin DEUTSCH connector, it isnecessary to use two boxes of the new box799-601-9320 and the currently using box799-601-2600. At this time, apply the plate(Part No.: 799-601-9310) on the current box799-601-2600.
Note 3. For your prompt preparation, we haveprepared a kit for the above application withthe KIT No. of 799-601-9300.[Component parts of the KIT 799-601-9300]
Introduction of the T-junction Adaptorfor the 24-Pin and 40-Pin DEUTSCH Connectors
Starting from the hydraulic excavators of Model PC58-3, PC78-6 and PC200-7, the controllers withthe common name of “NGI controller” are being used. To these controllers, 1 unit of 24-PinDEUTSCH Connector and 2 units of 40-Pin DEUTSCH Connectors are being connected.This PARTS & SERVICE OPERATION TIPS will introduce the T-junction adaptor for use withthese DEUTSCH connectors.
tcsgt
Inserted Text
2 of 2
2. How to use (in case of PC78US-6)Using method is same as that of theexisting T-junction adaptors.1) Remove the cover positioned behind the
operator’s seat to dispose the NGIcontroller before removing its clampingbolts.
NGI controller 40-Pin DEUTSCHconnectors
24-Pin DEUTSCHconnector
Clamping bolts
Hex wrench
2) Disconnect the connector using a hexwrench (B = 4mm).
3) Using the hex wrench (B = 4mm),connect the T-junction adaptor to theconnector which has been disconnectedas above.
Plate (799-601-9310)
Box (799-601-2600)
4) Connect the box to carry out the troubleshooting work.
5) In case of the 40-Pin DEUTSCH connector,apply the plate on the existing box beforeuse.
