HARMSCO INV 150702 INV... · Harmsco ® Involute Cartridge Filter Housings are available with...
Transcript of HARMSCO INV 150702 INV... · Harmsco ® Involute Cartridge Filter Housings are available with...
HARMSCO® INVHurricane® ® Involute
Model: INV-72-8FL series
Residential Drinking Water
Reverse Osmosis Pre-Filtration
Ground Water RemediationCooling Tower Filtration Utility WaterProcess Water Municipal Waste Water Treatment
Ground Water Under Direct Influence (GWUDI)
Up-Flow FiltrationA design so superior it’s patented.
Made in USAHARMSCO® Filtration Products
304L stainless steel construction, standardr
Integral mounting legs, drill in place
150 psi (10.3 bar) pressure rating
Electropolished finish, standard
Accepts 40” L x 2.5” OD or 2.75” ODcartridges in DOE or 222/Fin configurations.Two drains provided - inlet and outlet liquids
Flow rates of up to 1,900 gpmAll filter housings hydrostatically tested
Options:316 stainless steelSanitary, BSPT, or victaulic connections
Features
Applications
Industrial / Municipal
Extensive choice of cartridge micron ratingsand sizes
Harmsco® Hurricane® Involute® filter housings provideunsurpassed performance. The Hurricane® technologydesign separates dense solids prior to cartridgefiltration for extended filter life, increased dirtholding capacity and reduced operating costs.
Patented Involute design ensures uniform filtercartridge loading throughout the filter housing.
OverheadView
Harmsco® Involute® Cartridge Filter Housings are available withspecific internal components which allow for the use of eitherDOE or 222 / Fin end cap cartridges.
Harmsco® Hurricane® Involute® Housing INV
Finish - Electropolish standard;Inlet /Outlet - 8” Flange; Connections optional Construction - 304L stainless steel standard;
316L stainless or Duplex steel optionalClosure - Swing Bolt with Buna-N o-ring;Temperature- up to 250°F(121°C), housing only.
Pressure - Up to 150 psi (10.3 bar) max
Specifications
HARMSCO®
Filtration ProductsP.O. Box 14066, North Palm Beach, FL 33408(561) 848-9628 • Toll-free: (800) 327-3248 • Fax: (561) 845-2474 • E-mail: [email protected]
© 2013 Harmsco, Inc.
www.harmsco.comMade in USA
Note: This publication is to be used as a guide. The data within has been obtained from many sources and is considered to be accurate. Harmsco does not assume liability for the accuracy and/or completeness of this data. Changes to the data can be made without notification. Temperature, Pressure, Flow Rates, Differential Pressures, Chemical Combinations and other unknown factors can affect performance in unknown ways. Limited Warranty: Harmsco warrants their products to be free of material and workmanship defects. Determination of suitability of Harmsco products for uses and applications contemplated by Buyer shall be the sole responsibility of Buyer. The end user/installer/buyer shall be liable for the product’s performance and suitability regarding their specific intended applications. End users should perform their own tests to determine suitability for each application.
*Flow rates shown are for guidelines only. Actual flow rates are based on cartridge type, micron rating, viscosity, solids content and a number of other factors. For complete flow and pressure drop information please refer to your cartridge manufacturer guidelines.
Ordering Information
Cartridge Styles
DOE 222 / Fin
20"E
95-1/2"A
45-1/4"B
48"D
35-7/16C
23"
36"
27-3/16"GAUGE PORT1/4" FPT
45-1/4"
23-3/4"
13-3/4"
R 44"LID SERVICE AREA
VENT1/2" FPT
5-1/8"48"
13-3/4"REF
35-7/16"
1-1/2" FPTSIDE DRAIN
1-1/2" FPTBOTTOM DRAIN
20"
95-1/2"
70-1/4"
8" FLANGETANGENTIALINLET
8" FLANGEOUTLET
NOTE:115" CEILING HEIGHTRECOMMENDED FORSERVICING.
Filter ModelMax Flow
Rate* (GPM)Max Flow
Rate* (LPM)Max Flow
Rate* (M3/Hr)A
Filter HtB
WidthC
DiameterD
InletE
Outlet I/O Size I/O Type Drain SizeWeight (lbs)
INV-72-8FL-222 1900 7192 431 95.5” 45.25” 35.44” 48” 20” 8” FLANGE 1.5” FPT 1308
Pressure Drop
Flow Rate(GPM)(Flow curve specific to 2.75” Dia. cartridges)
Pre
ssu
re D
rop
(P
SI)
00 1900 21001700150013001100
1
2
3
4
5
6
7
8
INV-72-8FL
EPDM or Viton o-ring optional.
INV-72-8FL-DOE 1900 7192 431 95.5” 45.25” 35.44” 48” 20” 8” FLANGE 1.5” FPT 1308