Hardware Reference User Manual - AV Distributors · The following symbols may be used in this...

Hardware Reference User Manual

Model P110 Based Appliances

R591686 Revision 01

Barco P110

P ii

Hardware Reference User Manual - P110 Hardware Reference Manual, Document No. R591686_01 www.barco.com

Current Document Version Title: Model P110 – Hardware Reference Manual ID No.: R591686 Revision: 01 Date: May 2018

Trademarks Brand and product names mentioned in this manual may be trademarks, registered trademarks, or copyrights of their respective holders. All brand and product names mentioned in this manual serve as comments or ex-amples and are not to be understood as advertising for the products or their manufacturers.

Copyright © 2018 by Barco Die Weitergabe sowie die Vervielfältigung aller Unterlagen, die von uns überlassen werden, deren Verwertung und Mitteilung ihres Inhaltes an Dritte ist nicht gestattet, soweit dies nicht ausdrücklich zugestanden ist. Urhe-berrechte, insbesondere auch solche an Software, werden nur insoweit übertragen, als es für die Erreichung des speziellen Vertragszwecks erforderlich ist. Zuwiderhandlungen können zu Schadensersatz verpflichten. Alle Rechte aus der Erteilung eines Patents oder der Eintragung eines Gebrauchsmusters verbleiben bei uns.

Copyright © 2018 by Barco All rights reserved. No part of this document may be copied, reproduced, or translated. It shall not otherwise be recorded, transmitted, or stored in a retrieval system without the prior written consent of Barco.

Warranty Please refer to the warranty page on the Barco website: http://www.barco.com/en/about-barco/legal/warranty-policy.

http://www.barco.com/en/about-barco/legal/warranty-policy

Barco P110 Contents

P I

Hardware Reference User Manual - P110, Document No. R591686_01 www.barco.com

Contents

1 Preface ................................................................................................................................................................ 1 1.1 About this manual ................................................................................................................................................... 1

1.1.1 Styles ........................................................................................................................................................................................................................................ 1 1.1.2 Symbols ................................................................................................................................................................................................................................ 1

1.2 Online manuals ....................................................................................................................................................... 2 1.3 Safety instructions ................................................................................................................................................... 3

1.3.1 Standards ............................................................................................................................................................................................................................. 3 1.3.2 Precautions ....................................................................................................................................................................................................................... 3 1.3.3 Unpacking of devices ............................................................................................................................................................................................. 4 1.3.4 Environment conditions ...................................................................................................................................................................................... 4 1.3.5 General installation instructions ................................................................................................................................................................... 4 1.3.6 Servicing .............................................................................................................................................................................................................................. 4 1.3.7 Cleaning ............................................................................................................................................................................................................................... 4 1.3.8 Repacking .......................................................................................................................................................................................................................... 5

1.4 Delivery volume ...................................................................................................................................................... 5 1.5 Made in information ............................................................................................................................................... 5 1.6 Production date ...................................................................................................................................................... 5 1.7 Importer's contact information............................................................................................................................ 5

2 Model P110 ........................................................................................................................................................ 6 2.1 P110 front view ........................................................................................................................................................ 7

2.1.1 Power button .................................................................................................................................................................................................................. 7 2.1.2 Activity-status LED ..................................................................................................................................................................................................... 7

2.2 P110 rear view ......................................................................................................................................................... 8 2.2.1 Interfaces ............................................................................................................................................................................................................................ 8

2.3 P110 cooling concept ........................................................................................................................................... 9 2.4 Mounting options ................................................................................................................................................. 10

2.4.1 Horizontal setup ....................................................................................................................................................................................................... 10 2.4.2 Vertical setup ............................................................................................................................................................................................................... 11 2.4.3 Mounting brackets.................................................................................................................................................................................................. 12 2.4.4 VESA mount .................................................................................................................................................................................................................. 12 2.4.5 19”mount ......................................................................................................................................................................................................................... 12

2.5 Installing/replacing the hard drive .................................................................................................................... 13

3 Connecting P110 ............................................................................................................................................ 14 3.1 Connecting the display........................................................................................................................................ 14 3.2 Connecting keyboard and mouse ................................................................................................................... 15

3.2.1 Direct connection.................................................................................................................................................................................................... 15 3.2.2 Keyboard and mouse extension (optional) .................................................................................................................................... 15

3.3 Connecting audio ................................................................................................................................................ 16 3.4 Connecting network ........................................................................................................................................... 17 3.5 Connecting power supply .................................................................................................................................. 18

4 Technical data ................................................................................................................................................ 19

5 Disposal information .................................................................................................................................... 20 5.1 Disposal of batteries ............................................................................................................................................ 20

Barco P110 Contents

P II


5.2 Turkey RoHS compliance .................................................................................................................................. 20 5.3 EurAsian Conformity (EAC) ............................................................................................................................... 20

6 China RoHS compliance .............................................................................................................................. 21

7 Factory Address .............................................................................................................................................. 22

8 Contact ............................................................................................................................................................ 23

Barco P110 Preface

P 1


1 Preface This chapter gives general information about how this manual is organized and where to find additional doc-umentation

1.1 About this manual

1.1.1 Styles The typographic styles in this document are used as follows:

Style Description

Bold Labels, menus, and buttons are printed in Bold style.

Blue Links to other chapters of this manual and to sites on the Internet are printed in blue.

Courier Names of files and parts of programs are printed in Courier font.

Courier bold Inputs you are requested to make via the keyboard are printed in Courier bold font.

1.1.2 Symbols

The following symbols may be used in this document. Their meaning is explained in the following table.

Symbol Description

This icon specifies passages concerning solely the distributed system.

Failure to observe instructions marked by this icon may result in damage to the equipment!

Failure to observe instructions marked by this icon may result in electrical shock and danger to personal health!

Failure to observe instructions marked by this icon may result in damage to parts which are sensitive towards electrostatic charge!

Failure to observe instructions marked by this icon may result in being harmed by sharp objects!

Failure to observe instructions marked by this icon may result in parts exploding!

Failure to observe instructions marked by this icon may result in hot parts affecting persons or objects!

Barco P110 Preface

P 2


Symbol Description

Additional notes.

Further information.

Tips.

Important notes.

1.2 Online manuals Further documentation about your Barco product can be downloaded from the secured Barco website at www.barco.com/mybarco.

http://www.barco.com/mybarco

Barco P110 Preface

P 3


1.3 Safety instructions This section describes safety precautions which must be observed when installing and operating a product from Barco.

1.3.1 Standards

Safety Regulations

P110 is built in accordance with the requirements of international safety standards as mentioned in the provided Safety Manual.

Additionally it complies with the standard EN-62368-1.

All these safety standards are the information technology equipment standards, including electrical business equipment.

EN55032/CISPR32 class A MME (MultiMedia Equipment)

P110 is compliant with Class A of CISPR 32. In a residential environment this equipment may cause radio interference.

Class A ITE (Information Technology Equipment)

This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

FCC compliance statement

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfer-ence when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his/her own expense.

1.3.2 Precautions

Read the Safety Manual shipped with your product before installing and operating this device!

Take note of the instructions which have been compiled both to prevent personal injury and to ensure the device is operated in accordance with its intended use.

Ensure that you understand and follow all safety guidelines, safety instructions, and warnings mentioned in this document.

Barco P110 Preface

P 4


This product is intended for professional use only.

It is not intended for household use!

1.3.3 Unpacking of devices For unpacking, follow the instructions and advice indicated on the outside of the packaging!

1.3.4 Environment conditions The table below specifies the environment conditions in which the product may be safely operated or stored.

Environment Operating Non-Operating

Ambient temperature 0 to 40 deg C / 32 to 104 deg F -20 to 60 deg C / -4 to 150 deg F

Humidity 5% to 80% non-condensing 5% to 95% non-condensing

Altitude -60 to 5,000 m / -197 to 6,562 ft -60 to 10,000 m / -197 to 32,808 ft

The product must be stored and transported in the original packaging in accordance with the non-operating conditions specified above.

1.3.5 General installation instructions • Do not place this unit on an unstable cart, stand, or table. The unit may fall, causing serious damage to it.

• Do not use this unit near water.

• Do not use any power cords other than the one supplied with your unit. While appearing to be similar, other power cords have not been safety tested at the factory and must not be used to power the unit. For a replacement power cord, contact your dealer.

• Slots and openings in the cabinet and the sides are provided for ventilation; to ensure reliable operation of the unit and to protect it from overheating, these openings must not be blocked or covered. The open-ings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should never be placed near or over a radiator or heat register. This unit should not be placed in a built-in installation or enclosure unless proper ventilation is provided.

• The maximum recommended ambient temperature for this equipment is 40 C.

• When using the unit in a multi-unit rack assembly or closed assembly, the ambient temperature inside the assembly may not exceed the maximum rated ambient temperature.

• When installed in a rack, the installation should be such that the amount of air flow required for safe op-eration of the equipment is not compromised. The mounting of the equipment should be such that no hazardous condition is achieved due to uneven mechanical loading.

1.3.6 Servicing P110 does not require any servicing or regular maintenance work other than vacuuming the air vents in the housing rear and front at regular intervals.

1.3.7 Cleaning Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.

Barco P110 Preface

P 5


1.3.8 Repacking Keep the original shipping carton and packing material; they will be useful should you ever have to ship your unit. For maximum protection, repack your set as it was originally packed at the factory.

1.4 Delivery volume The delivery volume of your P110 controller includes the following items:

P110 controller, preinstalled with software image depending on the configuration

USB recovery stick (depending on configuration)

Power supply

DisplayPort-HDMI adapter (depending on configuration)

Vertical stand and mounting brackets

Part number, MAC address, and serial number labels

Quick Start Guide

Safety Manual

Never leave the USB stick in the USB port!

Booting the system while the USB stick is still connected will restart the installation!

If this case simply wait until the installation is completed. Your data or customized settings will not be lost.

1.5 Made in information The made in information is indicated on the product ID label on the product itself.

1.6 Production date The month and year of production is indicated on the product ID label on the product itself.

1.7 Importer's contact information To find your local importer, contact Barco directly via www.barco.com, or one of Barco's regional offices via http://www.barco.com/contact/regional-offices.

http://www.barco.com/

http://www.barco.com/contact/regional-offices

Barco P110 Model P110

P 6


2 Model P110 Based on the model P110 device, Barco is offering various appliances. The notion of an appliance is used in this context for market or use-case specific software packages running on this model P110 hardware.

P110 controller

This reference manual is mainly about the model P110 hardware!

For the latest information on the appliance check the product page on the secured Barco website http://www.barco.com/mybarco.



P 7


2.1 P110 front view

P110 front view

2.1.1 Power button

Action Function

Short press Switches ON, when system was OFF Initiates SHUTDOWN, when system was ON

Long press (>10 sec)

FORCED SHUTDOWN, when system was ON

Flashing white Access to SSD

Switching off the P110 will not disconnect all parts from the power supply.

To power down the whole device, short press the power button, then unplug the power plug when the LED is signalling OFF state.

2.1.2 Activity-status LED

Signalling Function

No light System is switched OFF or has no power

Blue light System is ON

Flashing white Access to SSD

Blinking blue regularly (50 % on, 50 % off)

System is in sleep mode

Blinking blue (other than 50 % on, 50 % off)

System is defective, please contact Barco support

Power button with Activity-status LED


P 8


2.2 P110 rear view

P110 rear view

2.2.1 Interfaces

Port Function

PS/2 (Kbd/Mouse) Legacy PS/2 type keyboard and mouse interface

USB 2.0 4x USB2.0 interfaces.

Device detection button and LED

For bi-directional identification of device vs mgmt. console (appliance dependent)

DP 2x Display Port 1.2 interfaces

(HDMI supported via adapters)

COM1 RS323 interface

DVI DVI-D Single Link interface

GbE I210 Gigabit Ethernet interface

GbE I219-LM Gigabit Ethernet interface

USB 3.0 4x USB3.0 interfaces

Line OUT Can also be configured in Bios as Headphone-out

Line IN Can also be configured in Bios as Mic-in or Rear-Speaker-Out

S/PDIF Digital audio interface

DC IN DC power input for the P110

Line IN

USB 3.0

GbE I210

Device detection button and LED

DP

S/PDIF

DC

USB 2.0

DVI

COM1 PS/2 GbE I219-LM

PS/2 Line OUT


P 9


2.3 P110 cooling concept The following image shows the air flow into and out of the P110:

Air intake [blue] Air output [red]

To protect the P110 from overheating, the air vents must be kept free of obstructions!


P 10


2.4 Mounting options Several mounting options are available.

It depends on the appliance type, whether the required brackets for a specific mounting option are included or available as an optional accessory.

2.4.1 Horizontal setup The P110 can be placed on and operated from a desk.

• Turn the device upside down.

• Attach the provided rubber feet to all 4 edges of the device.

P110 bottom view with rubber feet attached


P 11


2.4.2 Vertical setup Using the vertical stand, the P110 can be placed vertically on any even and stable surface. In this case the rubber feet will be attached to the bottom of the vertical stand. With the 2 provided TX8 screws, the vertical stand can be mounted on either side of the P110.

• Put the device on its side.

• Mount the vertical stand on the device using the 2 provided TX8 screws.

• Attach the provided rubber feet to all 4 edges.

Attaching P110 vertical stand

P110 vertical stand with rubber feet attached

To protect the P110 from overheating, the air vents must be kept free of obstructions at all times!


P 12


2.4.3 Mounting brackets Using the 2 provided mounting brackets, the P110 can be mounted on top of a surface or below a surface.

P110 Mounting bracket variations

• Use the 4 provided screws to mount the brackets to the device on both sides in the desired layout.

Brackets for mounting P110 on top of a surface

Brackets for mounting P110 below a surface

To protect the P110 from overheating, the air vents must be kept free of obstructions at all times!

2.4.4 VESA mount A VESA mount to attach the P110 controller to the back of a display can be purchased separately.

For instructions on the VESA mount please refer to the Quick Start User Guide supplied with the mount.

2.4.5 19”mount A 19” mount to place the P110 controller inside a server rack can be purchased separately.

For instructions on the 19” rack mount please refer to the Quick Start User Guide supplied with the mount.


P 13


2.5 Installing/replacing the hard drive P110 controllers feature a flash drive with an SSD storage medium accessible from the bottom. The storage medium can be swapped by accessing the 2.5" slim type hard drive bay.

Pull out the cable from the DC in connection to disconnect the P110 controller from the power supply before you remove or insert a hard drive.

• Unscrew the cover using a TX8 screw driver.

• Remove the cover.

P110 bottom view with hard drive bay

• Slide the SSD to the rear to disconnect it.

• Remove the SSD from the bay.

Disconnecting the hard drive

• Proceed in reverse order to insert a new drive.

2.5" slim type hard drive bay

Barco P110 Connecting P110

P 14


3 Connecting P110

To prevent damage of the P110 do not connect your device to the power supply until all other cables have been connected!

3.1 Connecting the display P110 controller can be connected to a display via DisplayPort® cables or via HDMI cables by using Display-Port®-to-HDMI adapters.

P110 rear view

DisplayPort®-to-HDMI adapter


P 15


3.2 Connecting keyboard and mouse You can connect a keyboard and a mouse to the USB ports on your P110 controller, if desired.

Keyboard and mouse (or keyboard and mouse extension) are not included in the delivery volume.

3.2.1 Direct connection Both keyboard and mouse feature a USB interface.

• Plug the USB cables of the devices into the USB ports on the controller (cf. section P110 rear view)

• With wireless keyboard and mouse, proceed accordingly with the respective keyboard/mouse receivers.

Direct keyboard & mouse connection

3.2.2 Keyboard and mouse extension (optional) A keyboard extension (not provided) allows for a remote positioning of keyboard and mouse. The extension consists of two extension boxes and two connection cables.

The image below shows the parts and the cabling of the keyboard extension:

Keyboard and mouse extension:

Remote extension box REX [4] Local extension box LEX [1] RJ45 connection cable [3]

USB cable [2]

• Plug the keyboard and mouse into the remote extension box. With wireless keyboard and mouse, proceed accordingly with the respective keyboard/mouse receivers.

• Connect the remote extension box to the local extension box by means of the 20m connection cable.

• Connect the local extension box to one of the USB ports on the controller (cf. section P110 rear view) us-ing the USB cable provided, featuring a USB-A plug on one end and a USB-B plug on the other.


P 16


3.3 Connecting audio Should you wish to connect audio to your P110, use the audio connectors on the rear (if any).

Note that audio jacks Line in /Line out are configurable for Mic in/ Headphone or Rear speaker out.

P110 rear view

Line IN Line OUT

S/PDIF


P 17


3.4 Connecting network In order to receive streamed videos and control data, and to show application data from other system devic-es, P110 controllers must be connected to a Local Area Network (LAN).

If you have an existing LAN for your business data, it is important to decide in advance if you will use this LAN for all data or rather set up a second LAN for the video data. This would be your video network or video LAN.

Prior to connecting your video LAN to the P110 controller(s) for the first time, consult the respective software user manual for instructions on the required initial configuration!

The latest editions of our user manuals can be found on the secured Barco website www.barco.com/mybarco.

Network and data cable connections can be made while the system is running. However, if the network connection is set to use a DHCP server, a reboot may be required. For details on the DHCP setting, please refer to the software user manual on the secured Barco website www.barco.com/mybarco.

P110 rear view

LAN connectors (RJ45)




P 18


3.5 Connecting power supply

Check the power rating on your outlet before connecting the external power supply unit of your P110 to the wall outlet or to a power strip. Contact your facilities manager or a qualified electrician if you are not sure about the type of power supplied to your building.

The P110 is designed to operate with single-phase power systems having a grounded neutral conductor. To reduce the risk of electrical shock, do not plug into any other type of power system.

• Plug the DC power connector of the power supply into the DC in connection of your P110

• Tighten the thumb screw.

P110 rear view and external power supply

• Connect the external power supply to a power outlet (power cable is included in delivery volume for most countries).

For power cords not provided, contact your local dealer.

Make sure power cables are approved for your country!

Barco P110 Technical data

P 19


4 Technical data This table provides an overview of the technical data of the P110 device and its built-in components.

CPU (depending on configuration)

Intel Core i7-6700 processor



Intel Core i3-7101E processor


Memory (depending on configuration)

2 x 2 GB, PC4-2400, DDR4, SO-DIMM




SSD 2.5" slim type, various capacities

DC power (P110 device) 12Vdc, 9A

Power mains (external power supply) 90-264 V, 2 A, 47-63 Hz

Efficiency (external power supply) 88.8% @115V, 90,2%@ 230V

Inrush current (external power supply) 72.5/174 A for 100/240 VAC max.

Mains power cords

(depending on configuration)

CEE 7

NEMA 5-15

GB 2099

power consumption Switched off mode

Sleep mode Idle mode

max. operating mode

< 0.25 W < 1.5 W < 11 W < 120 W

operating conditions

Altitude

0..40°C / 32..104°F at 5.. 80% humidity, non-condensing

-60m to 5,000 m / -197 to 6,562 ft

Non-operating conditions Altitude -20..60°C / -4..150°F at 5..95% humidity, non-condensing -60 to 10,000 m / -197 to 32,808 ft

Note: The product must be stored and transported in the origi-nal packaging in accordance with the non-operating conditions specified above

noise level 32db(A) at 25°C ambient temperature at 100% CPU load

dimensions (h/w/d) with fixation

with vertical stand power supply w/o cable

60 mm / 190 mm / 190 mm | 2.36 in / 7.48 in / 7.48 in 60 mm / 228 mm / 190 mm | 2.36 in / 8.98 in / 7.48 in 206 mm / 80 mm / 190 mm | 8.11 in / 3.15 in / 7.48 in 42 mm / 72 mm / 171 mm | 1.65 in / 2.83 in / 6.73 in

Weight P110 unit Weight power supply

2.1 kg | 4.63 lbs 0.7 kg | 1.54 lbs

Barco P110 Disposal information

P 20


5 Disposal information This symbol on the product indicates that, under the European Directive 2012/19/EU governing waste from electrical and electronic equipment, this product must not be disposed of with other municipal waste. Please dispose of your waste equipment by handing it over to a desig-nated collection point for the recycling of waste electrical and electronic equipment. To pre-vent possible harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly to pro-mote the sustainable reuse of material resources.

For more information about recycling of this product, please contact your local city office or your municipal waste disposal service. For details, please visit the Barco website at http://www.barco.com/en/AboutBarco/weee.

5.1 Disposal of batteries This product contains batteries covered by the Directive which must be collected and disposed of separately from municipal waste.

If the battery contains more than the specified values of lead (Pb), mercury (Hg) or cadmium (Cd), these chemical symbols will appear below the crossed-out wheeled bin symbol.

By participating in separate collection of batteries, you will help to ensure proper disposal and to prevent potential negative effects on the environment and human health.

5.2 Turkey RoHS compliance

Turkiye Cumhuriyeti: AEEE Yönetmeliğine Uygundur

[Republic of Turkey: In conformity with the WEEE Regulation]

5.3 EurAsian Conformity (EAC)

This product complies with the Safety of Low-Voltage Equipment (LVE Technical Regulation 004/2011, CU TR 004/2011) and the Electromagnetic Compatibility of Technical Products (EMC Technical regulation, CU TR 020/2011).

http://www.barco.com/en/AboutBarco/weee

Barco P110 China RoHS compliance

P 21


6 China RoHS compliance

Barco P110 Factory Address

P 22


7 Factory Address

Kontron Europe GmbH

Lise-Meitner-Str. 3-5

D-86156 Augsburg

Germany

Phone +49 (0) 821 4086-01

Fax +49 (0) 821 4086 111

www.kontron.com

http://www.kontron.com/

Barco P110 Contact

P 23


8 Contact

Visit Barco at www.barco.com

For Professional Support visit

http://www.barco.com/support

For Sales or other regional contact information visit


Barco N.V.

Beneluxpark 21 – 8500 Kortrijk (Belgium)

Registered Office:

Barco N.V.

Pres. Kennedypark 35 – 8500 Kortrijk (Belgium)

RPR Kortrijk - BE0473191041

http://www.barco.com/

http://www.barco.com/support


Hardware Reference User Manual - AV Distributors · The following symbols may be used in this...

Documents

Transcript of Hardware Reference User Manual - AV Distributors · The following symbols may be used in this...