Hard metals for precision tools - Sanimex · hard material matters Hard metals for precision tools....
-
Upload
truongthien -
Category
Documents
-
view
221 -
download
1
Transcript of Hard metals for precision tools - Sanimex · hard material matters Hard metals for precision tools....
ha
rd m
ate
ria
l m
att
ers
Hard metals for
precision tools
2
Headquarters and parent company in MAMER / Luxembourg
Parent company in REUTTE / Austria
CERATIZIT - the parent companies
Direct sales and distribution partners
3
Our quality management systems meet the highest standards.
4
5
Grade guide . . . . . . . . . . . . . . . . . . . . . . . . . . .6 - 7
Sintered rods . . . . . . . . . . . . . . . . . . . . . . . . . .8 - 9
Sintered rods for inch dimensions . . . . . . . . . . . . . . . 10
Sintered rods for mould making tools TSF . . . . . . . . . . . 11
Sintered cermet rods . . . . . . . . . . . . . . . . . . . . . . 12
Ground rods . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Ground rods for mould making tools TSF . . . . . . . . . . . 14
Ground rods for solid carbide end mills . . . . . . . . . . . . 15
Silicon nitride rods . . . . . . . . . . . . . . . . . . . . . . . . 16
Sintered rods with two helical coolant holes . . . . . . . 17 - 22
Sintered rods with three helical coolant holes . . . . . . 23 - 25
Sintered rods with two straight coolant holes . . . . . . 26 - 29
Sintered rods with one straight coolant hole . . . . . . . . . 30
Sintered rectangular rods . . . . . . . . . . . . . . . . . 31 - 35
Sintered square rods . . . . . . . . . . . . . . . . . . . . . . 36
Tips for reamers . . . . . . . . . . . . . . . . . . . . . . . . . 37
Brazing tips for spiral fl uted milling cuttersand long edge milling cutters . . . . . . . . . . . . . . . . . . 38
ContentsPage
6
TSF22 K10-K20 C-2 – 8,2 14,55 1970 1930 93,7 4400 638.000
TSF44 K10-K30 C-2 – 12,0 14,10 1760 1730 92,7 4600 667.000
MG12K05-K10 C-3 – 6,0
14,80 1820 1790 93,0 3500 507.500
TSM10 14,90 1880 1850 93,3 3300 478.500
TSM20 K10-K30 C-3 – 7,5 14,75 1750 1720 92,6 3500 507.500
TSM33K20-K40 C-2 – 10,0
14,35 1610 1590 91,9 3700 536.500
MG18 14,50 1680 1660 92,3 3700 536.500
HC10 K10 C-3 – 5,6 15,00 1760 1730 92,7 2150 311.900
H20X K15 C2 – 6,0 14,95 1670 1650 92,2 2300 333.500
S4X7 P30-P35 C-5 11,2 11,0 13,20 1490 1470 91,0 2300 333.500
TCN54 HAT-P20 – – – 14,1 6,40 1650 1630 92,1 2000 290.000
SNC1 CN-K20 – – – 9,0 3,25 1550 1530 91,5 1100 159.500
(%) g/cm³ HV10 HV30 HRA MPa P.S.I.
< 0.2
0.2 - 0.5
0.5 - 0.8
0.8 - 1.3
1.3 - 2.5
2.5 - 6.0
> 6.0
Grades -Composition and properties
GradeISO
code
Code
USA
Grain
size
TiC/
Ta(Nb)C
Binder Density
HardnessTransverse rupture
strength
TUNGSTEN CARBIDE COBALT GRADE
WC-TiC/TaC - COBALT GRADE
CERMET
SILICON NITRIDE GRADE
Classifi cation of tungsten carbide grain size
Tungsten carbide grain size [µm] Classifi cation
nano
ultrafi ne
submicron
fi ne
medium
coarse
extra-coarse
Ultrafi ne
Ultrafi ne
Submicron
Submicron
Submicron
Fine
Fine
Fine
7
TSF22
TSF44
TSM10
MG12
TSM20
TSM33
MG18
HC10
H20X
S4X7
TCN54
SNC1
Grades -Description
Special ultrafi ne carbide grade for HSC machining.
For machining hard and super-hard materials > 60 HRC.
Special ultrafi ne carbide grade for HSC machining.
e.g. 1.2311 or 1.2312; hardened up to 59 HRC.
Hard
ness
Toughness
Submicron grade for rotating solid carbide tools.
For machining non ferrous metals, aluminium alloys, glass and carbon fi bre
reinforced plastics, artifi cial carbon, graphite, cast irons of low or medium
hardness, chilled castings, hardened steels.
Submicron grade for rotating solid carbide tools. For machining grey cast iron,
tempered iron, non alloyed steels, super alloys, titanium and tantalum alloys,
heat resistant steels, plastics.
Submicron grade for rotating solid carbide tools. For machining stainless steels,
corrosion and heat resistant steels, chromium alloyed steels, nickel & cobalt alloyed steels, titanium alloys, non ferrous metals, plastics.
Hard
ness
Toughness
Hard
ness
Toughness
High wear resistance with relatively low toughness requirements.
Suitable for brazing tips.
High wear resistance with medium toughness.
Suitable for deep gun drills and brazing tips.
High toughness with good impact strength and T.R.C. for interrupted cut. For
machining steel, cast steel (also with sand inclusions), austenitic steels with
medium or low cutting speeds, also for unfavourable machining conditions.
Special cermet quality for the production of high-performance tools for
fi ne fi nishing when good surface quality and high dimensional accuracy
are required.
Silicon nitride for the production of tools for grey cast iron machining
U l t r a f i n e g r a d e s
S u b m i c r o n g r a d e s
F i n e g r a i n g r a d e s
S p e c i a l i t i e s
8
RR 0115 1,15
-0/+0,15
r r x
-0/+0,3
x
RR 0165 1,65 r r x x x
RR 0180 1,80 r r x
RR 0220 2,20-0/+0,2
r x x x x r
RR 0270 2,70 r r x x
RR 0325 3,25 -0/+0,1 x x x x x r
RR 0370 3,70
-0/+0,2
r r x x
RR 0420 4,20 x x x x x r
RR 0470 4,70 r r x x
RR 0520 5,20
-0/+0,25
r r x x r
RR 0570 5,70 r r x x
RR 0620 6,20 x x x x x x
RR 0670 6,70 r r x x
RR 0720 7,20
-0/+0,30
r r x x
RR 0770 7,70 r r x x
RR 0820 8,20 x x x x x x
RR 0870 8,70 r r x x
RR 0920 9,20 r r x x
RR 0970 9,70 r r x x
RR 1020 10,20 x x x x x x
RR 1070 10,70 r r x x
RR 1120 11,20 r r x x
D
[mm]
L=330 L=325
TSM10K05-K10
TSM20K10-K30
TSM33K20-K40
MG12K05-K10
MG18K20-K40
S4X7P30-P35
Sintered rods
RR 0115
Diameter 1,15 mm
Sintered rods
x= stock item
r= limited stock or upon request
Other grades and dimensions upon request
Ordering codeDia.tol.[mm]
Dia.tol.[mm]
9
D
[mm]
L=330 L=325
TSM10K05-K10
TSM20K10-K30
TSM33K20-K40
MG12K05-K10
MG18K20-K40
S4X7P30-P35
RR 1170 11,70
-0/+0,3
r x
-0/+0,3
x
RR 1220 12,20 x x x x x x
RR 1270 12,70 r r x x
RR 1320 13,20 r r x x
RR 1370 13,70 r r x x
RR 1420 14,20 x x x x x x
RR 1470 14,70 r r x x
RR 1520 15,20 r r x x
RR 1620 16,20
-0/+0,45
x x x x x r
RR 1720 17,20 r r x x
RR 1820 18,20 x x x x x r
RR 1920 19,20 r r x x
RR 2020 20,20 x x x x x r
RR 2120 21,20
-0/+0,55
r r x x
RR 2220 22,20 r r x x r
RR 2320 23,20 r r x x
RR 2420 24,20 r r x x
RR 2520 25,20
-0/+0,65
r x x x x r
RR 2620 26,20 r r x
-0/+0,6
x
RR 2820 28,20 r r x x r
RR 3020 30,20 r r x x
RR 3220 32,20 r r x x
Sintered rods
RR 1170
Diameter 11.7 mm
Sintered rods
x= stock item
r= limited stock or upon request
Other grades and dimensions upon request
Ordering codeDia.tol.[mm]
Dia.tol.[mm]
10
D
[mm]
L=330 L=325
TSM33K20-K40
MG18K20-K40
RR 0325 3,25 1/8′′ -0/+0,10 x
-0/+0,30
x
RR 0500 5,00 3/16′′
-0/+0,25
r
RR 0540 5,40 13/64′′ r
RR 0655 6,55 1/4′′ r
RR 0740 7,40 9/32′′
-0/+0,30
r
RR 0820 8,20 5/16′′ x x
RR 0900 9,00 11/32′′ r
RR 0970 9,70 3/8′′ x x
RR 1100 11,00 27/64′′ r
RR 1300 13,00 1/2′′ r
RR 1470 14,70 9/16′′
-0/+0,45
x x
RR 1770 17,70 11/16′′ r
RR 1920 19,20 3/4′′ x x
RR 2100 21,00 13/16′′-0/+0,55
r
RR 2250 22,50 7/8′′ r
RR 2580 25,80 1′′ -0/+0,65 r
Sintered rods for inch dimensions
RR 0500
Diameter 5.00 mm
Sintered rods
x= stock item
r= limited stock or upon request
Other grades and dimensions upon request
For finished
inch
dimensions
Ordering codeDia.tol.[mm]
Dia.tol.[mm]
11
D
[mm]
L=330
TSF44K10-K30
TSF22K10-K20
RR 0220-330 2,20 -0/+0,20 r r
RR 0325-330 3,25 -0/+0,10 x x
RR 0420-330 4,20 -0/+0,20 x x
RR 0520-330 5,20-0/+0,25
r r
RR 0620-330 6,20 x x
RR 0820-330 8,20
-0/+0,30
x x
RR 1020-330 10,20 x x
RR 1220-330 12,20 x x
RR 1420-330 14,20 x x
RR 1620-330 16,20 x x
RR 1820-330 18,20-0/+0,55
x x
RR 2020-330 20,20 x x
RR 2520-330 25,20-0/+0,65
x r
RR 3220-330 32,20 x
Sintered rods for mould making toolsFor machining hard and super-hard materials
x= stock item
r= limited stock or upon request
Other grades and dimensions upon request
RR 0420-330
Length 330mm
Diameter 4.20 mm
Sintered rods
Ordering codeDia.tol.[mm]
12
D
[mm]
L=325
TCN54HAT-P20
RR 0325-325 3,25
-0/+0,30
x
RR 0420-325 4,20 x
RR 0520-325 5,20 x
RR 0620-325 6,20 x
RR 0720-325 7,20 x
RR 0820-325 8,20 x
RR 1020-325 10,20 x
RR 1120-325 11,20 x
RR 1220-325 12,20 x
RR 1320-325 13,20 x
RR 1420-325 14,20 x
RR 1520-325 15,20 r
RR 1620-325 16,20 r
RR 1720-325 17,20 r
RR 1820-325 18,20 r
RR 1920-325 19,20 r
RR 2020-325 20,20 r
RR 2220-325 22,20 r
Sintered cermet rods
RR 0420
Diameter 4.20 mm
Sintered rods
x= stock item
r= limited stock or upon request
Other grades and dimensions upon request
Ordering codeDia.tol.[mm]
13
D
[mm]
L=330
TSM33K20-K40
L=325
MG18K20-K40
D
[mm]
L=330
TSM33K20-K40
L=325
MG18K20-K40
RG 0100 1,00
+0/-0,006
x
RG 0150 1,50 r
RG 0200 2,00 x x
RG 0250 2,50 r
RG 0300 3,00 x x
RG 0350 3,50
+0/-0,008
r
RG 0400 4,00 x x
RG 0450 4,50 r
RG 0500 5,00 x x
RG 0550 5,50 r
RG 0600 6,00 x x
RG 0650 6,50
+0/-0,009
r
RG 0700 7,00 r
RG 0750 7,50 r
RG 0800 8,00 x x
RG 0850 8,50 r
RG 0900 9,00 r
RG 0950 9,50 r
RG 1000 10,00 x x
RG 1050 10,50
+0/-0,011
r
RG 1100 11,00 r
RG 1150 11,50 r
RG 1200 12,00 x x
RG 1250 12,50 r
RG 1300 13,00 r
RG 1350 13,50 r
RG 1400 14,00 x x
RG 1450 14,50 r
RG 1500 15,00 x
RG 1550 15,50 r
RG 1600 16,00 x x
RG 1800 18,00 x x
RG 2000 20,00
+0/-0,013
x x
RG 2200 22,00 x
RG 2400 24,00 x
RG 2500 25,00 x x
RG 2800 28,00 x
RG 3000 30,00 x
RG 3200 32,00 +0/-0,016 x
Ground rods
ground
x= stock item
r= limited stock or upon request
Other grades and dimensions upon request
Diameter tolerance: according to DIN ISO 286/h6
Surface quality: Ra <0,05 µm polished-ground
RG 0100
Diameter 1.00 mm
Sintered rods
Ordering codeOrdering code
Dia.tol.[mm]
Dia.tol.[mm]
14
D
[mm]
L=325
TSF44K10-K30
TSF22K10-K20
RG 0200-330 2,00
+0/-0,008
r r
RG 0300-330 3,00 x x
RG 0400-330 4,00 x x
RG 0500-330 5,00 r r
RG 0600-330 6,00 x x
RG 0800-330 8,00+0/-0,009
x x
RG 1000-330 10,00 x x
RG 1200-330 12,00
+0/-0,011
x x
RG 1400-330 14,00 r r
RG 1600-330 16,00 x x
RG 1800-330 18,00 r r
RG 2000-330 20,00 x x
RG 2500-330 25,00 r r
Ground rods for mould making toolsFor machining hard and super-hard materials
x= stock item
r= limited stock or upon request
Other grades and dimensions upon request
Diameter tolerance: according to DIN ISO 286/h6
Surface quality: Ra <0,05 µm polished-ground
RG 0600-330
Length 330mm
Diameter 6.00 mm
Ground rods
ground
Ordering code
Dia.tol.[mm]
15
D
[mm]
L
[mm]
c
[mm]
TSF22K10-K20
TSF44K10-K30
TSM33K20-K40
RGDC 0300-039 3,00 +0/-0,006 39 0,3 x x x
RGDC 0400-051 4,00
+0/-0,008
51 0,4 x x x
RGDC 0500-051 5,00 51 0,4 x x x
RGDC 0600-051 6,00 51 0,4 x x x
RGDC 0600-055 6,00+0/-0,008
55 0,4 x x x
RGDC 0600-058 6,00 58 0,4 x x x
RGDC 0800-059 8,00+0/-0,009
59 0,6 x x x
RGDC 0800-064 8,00 64 0,6 x x x
RGDC 1000-067 10,00+0/-0,009
67 0,6 x x x
RGDC 1000-073 10,00 73 0,8 x x x
RGDC 1200-074 12,00+0/-0,011
73 0,8 x x x
RGDC 1200-084 12,00 84 0,8 x x x
RGDC 1400-076 14,00
+0/-0,011
76 0,8 x x x
RGDC 1400-084 14,00 84 0,8 x x x
RGDC 1600-083 16,00 83 0,8 x x x
RGDC 1600-093 16,00 93 0,8 x x x
RGDC 1800-085 18,00+0/-0,011
85 1,0 x x x
RGDC 1800-093 18,00 93 1,0 x x x
RGDC 2000-093 20,00+0/-0,013
93 1,0 x x x
RGDC 2000-105 20,00 105 1,0 x x x
Ground rodsSemi-fi nished products for solid carbide milling cutters to DIN 6527 short and long
x= stock item
Other grades and dimensions upon request
ground
Diameter tolerance: according to DIN ISO 286/h6
Surface quality: Ra <0,05 µm polished-ground
Ordering code Dia.tol.
[mm]
16
D
[mm]
L
[mm]SNC1
CN-K20
5.0x66 5,0 66 r
6.0x66 6,0 66 r
7.0x79 7,0 79 r
8.0x79 8,0 79 r
9.0x89 9,0 89 r
10.0x89 10,0 89 r
11.0x102 11,0 102 r
12.0x102 12,0 102 r
13.0x107 13,0 107 r
14.0x107 14,0 107 r
15.0x115 15,0 115 r
16.0x115 16,0 115 r
17.0x123 17,0 123 r
18.0x123 18,0 123 r
19.0x131 19,0 131 r
20.0x131 20,0 131 r
5.0x77 5,0 77 r
6.0x77 6,0 77 r
7.0x91 7,0 91 r
8.0x91 8,0 91 r
9.0x103 9,0 103 r
10.0x103 10,0 103 r
11.0x118 11,0 118 r
12.0x118 12,0 118 r
13.0x124 13,0 124 r
14.0x124 14,0 124 r
15.0x133 15,0 133 r
16.0x133 16,0 133 r
17.0x143 17,0 143 r
18.0x143 18,0 143 r
19.0x153 19,0 153 r
20.0x153 20,0 153 r
D
[mm]
L
[mm]SNC1
CN-K20
Ground silicon nitride rods
Ordering code
r= limited stock or upon request
Other grades and dimensions upon request
Tolerance:Diameter: h6
Ordering code
ground
17
D
[mm]
D1
[mm]
d
[mm]
[mm]
L
[mm]TSM33
K20-K40
MG18K20-K40
RRK2 0430/1,3/0,7/18,0 4,3 1,30 0,70 18,0 330 r
RRK2 0430/2,1/0,45/21,8 4,3 2,10 0,45 21,8 325 x
RRK2 0580/2,2/0,9/29,0 5,8 2,20 0,90 29,0 330 r
RRK2 0600/2,7/0,8/32,7 6,0 2,70 0,80 32,7 330 r
RRK2 0630/2,0/0,9/32,7 6,3 2,00 0,90 32,7 330 x
RRK2 0630/2,2/0,7/32,7 6,3 2,20 0,70 32,7 330 x
RRK2 0630/2,5/1,0/32,7 6,3 2,50 1,00 32,7 325 x
RRK2 0630/2,7/0,8/32,7 6,3 2,70 0,80 32,7 330 x
RRK2 0680/2,7/0,8/35,4 6,8 2,70 0,80 35,4 330 r
RRK2 0730/3,5/0,9/38,1 7,3 3,50 0,90 38,1 325 x
RRK2 0730/3,2/0,9/40,8 7,3 3,20 0,90 40,8 330 r
RRK2 0780/3,2/0,9/40,8 7,8 3,20 0,90 40,8 330 r
RRK2 0830/3,4/1,0/43,5 8,3 3,40 1,00 43,5 325 x
RRK2 0830/3,4/1,0/43,5 8,3 3,40 1,00 43,5 330 x
RRK2 0880/3,7/1,0/46,3 8,8 3,70 1,00 46,3 330 r
RRK2 0930/4,2/1,0/49,0 9,3 4,20 1,00 49,0 330 r
RRK2 0930/4,35/1,0/49,0 9,3 4,35 1,00 49,0 325 x
RRK2 0980/4,8/1,3/54,4 9,8 4,80 1,30 54,4 330 r
RRK2 1030/4,8/1,3/54,0 10,3 4,80 1,30 54,0 325 x
RRK2 1030/4,8/1,3/54,4 10,3 4,80 1,30 54,4 330 x
RRK2 1080/5,7/1,5/59,9 10,8 5,70 1,50 59,9 330 r
RRK2 1130/5,5/1,5/59,9 11,3 5,50 1,50 59,9 325 x
RRK2 1130/5,7/1,5/59,9 11,3 5,70 1,50 59,9 330 r
RRK2 1180/6,3/1,7/65,3 11,8 6,30 1,70 65,3 330 r
RRK2 1230/6,3/1,7/65,3 12,3 6,30 1,70 65,3 330 x
RRK2 1230/6,3/1,6/65,3 12,3 6,30 1,60 65,3 325 x
RRK2 1280/7,0/1,7/70,7 12,8 7,00 1,70 70,7 330 r
RRK2 1330/6,5/1,6/70,7 13,3 6,50 1,60 70,7 325 x
RRK2 1330/7,0/1,7/70,7 13,3 7,00 1,70 70,7 330 r
Sintered rods with 2 helical coolant holes
Helix angle
Nominal pitch
Ordering code
18
D
[mm]
D1
[mm]
d
[mm]
[mm]
L
[mm]TSM33
K20-K40
MG18K20-K40
RRK2 1380/7,6/2,0/76,2 13,8 7,60 2,00 76,2 330 r
RRK2 1430/6,7/1,8/76,2 14,3 6,70 1,80 76,2 330 x
RRK2 1430/7,0/2,0/76,2 14,3 7,00 2,00 76,2 330 x
RRK2 1430/7,0/2,0/76,2 14,3 7,00 2,00 76,2 325 x
RRK2 1430/7,6/2,0/76,2 14,3 7,60 2,00 76,2 330 x
RRK2 1480/7,6/2,0/81,6 14,8 7,60 2,00 81,6 330 r
RRK2 1530/7,6/2,0/81,6 15,3 7,60 2,00 81,6 330 r
RRK2 1530/7,7/2,0/81,6 15,3 7,70 2,00 81,6 325 x
RRK2 1580/8,6/2,5/87,1 15,8 8,60 2,50 87,1 330 r
RRK2 1630/8,0/2,0/87,1 16,3 8,00 2,00 87,1 330 x
RRK2 1630/8,6/2,5/87,1 16,3 8,60 2,50 87,1 330 x
RRK2 1630/8,6/2,5/87,1 16,3 8,60 2,50 87,1 325 x
RRK2 1680/9,0/2,5/92,5 16,8 9,00 2,50 92,5 330 r
RRK2 1730/8,9/2,5/92,5 17,3 8,90 2,50 92,5 325 x
RRK2 1730/9,0/2,5/92,5 17,8 9,00 2,50 92,5 330 r
RRK2 1780/9,7/2,8/98,0 17,8 9,70 2,80 98,0 330 r
RRK2 1830/9,0/2,3/98,0 18,3 9,00 2,30 98,0 330 x
RRK2 1830/9,7/2,8/98,0 18,3 9,70 2,80 98,0 330 x
RRK2 1830/9,7/2,8/98,0 18,3 9,70 2,80 98,0 325 x
RRK2 1880/10,4/2,8/103,4 18,8 10,40 2,80 103,4 330 r
RRK2 1930/10,1/2,8/103,4 19,3 10,10 2,80 103,4 325 x
RRK2 1930/10,4/2,8/103,4 19,8 10,40 2,80 103,4 330 r
RRK2 1980/10,7/3,2/108,8 19,8 10,70 3,20 108,8 330 r
RRK2 2030/10,0/2,5/108,8 20,3 10,00 2,50 108,8 330 x
RRK2 2030/10,7/3,2/108,8 20,3 10,70 3,20 108,8 330 x
RRK2 2030/10,7/3,2/108,8 20,3 10,70 3,20 108,8 325 x
RRK2 2130/11,5/3,2/114,2 21,3 11,50 3,20 114,2 325 x
RRK2 2230/11,7/3,2/119,7 22,3 11,70 3,20 119,7 330 r
RRK2 2230/12,0/3,2/119,7 22,3 12,00 3,20 119,7 325 x
RRK2 2530/11,5/3,5/119,0 25,3 11,50 3,50 119,0 330 x
RRK2 2530/12,0/2,5/119,0 25,3 12,00 2,50 119,0 330 x
RRK2 2530/12,0/3,2/139,3 25,3 12,00 3,20 139,3 325 x
Sintered rods with 2 helical coolant holes
Helix angle
Nominal pitch
Ordering code
19
D
[mm]
D1
[mm]
d
[mm]
[mm]
L
[mm]TSM33
K20-K40
MG18K20-K40
RRK2 0530/2,2/0,6/24,5 5,3 2,2 0,60 24,5 325 x
RRK2 0630/1,6/0,5/18,0 6,3 1,6 0,50 18,0 350 x
RRK2 0630/1,6/0,5/18,0 6,3 1,6 0,50 18,0 325 x
SBR2 0630/1,9/0,7/22,1 6,3 1,9 0,70 22,1 350 x
SBR2 0630/2,0/0,5/22,5 6,3 2,0 0,50 22,5 325 x
RRK2 0630/2,2/0,9/29,0 6,3 2,2 0,90 29,0 350 x
RRK2 0830/3,3/1,0/35,0 8,3 3,3 1,00 35,0 350 x
RRK2 0830/3,3/1,0/35,0 8,3 3,3 1,00 35,0 325 x
RRK2 0830/3,6/0,9/38,1 8,3 3,6 0,90 38,1 325 x
RRK2 0830/3,3/1,0/43,5 8,3 3,3 1,00 43,5 350 x
RRK2 1030/4,4/1,15/46,0 10,3 4,4 1,15 46,0 330 x
RRK2 1030/4,4/1,15/46,0 10,3 4,4 1,15 46,0 325 x
RRK2 1030/4,8/1,3/54,4 10,3 4,8 1,30 54,4 330 x
RRK2 1030/5,0/1,2/49,0 10,3 5,0 1,20 49,0 325 x
RRK2 1230/5,4/1,5/57,0 12,3 5,4 1,50 57,0 250 x
RRK2 1230/5,4/1,5/57,0 12,3 5,4 1,50 57,0 325 x
RRK2 1230/6,3/1,7/65,3 12,3 6,3 1,70 65,30 250 X
RRK2 1230/6,0/1,5/59,9 12,3 6,0 1,50 59,90 325 x
Sintered rods with 2 helical coolant holesin multiple lengths for tools with unifi ed shank
x= stock item
Other grades and dimensions upon request
RRK2 - rods:For the production of DIN tools and special tools
RRK2 0630/1,6/0,5/18,0
Nominal pitch of coolant holes 18.0 mm
Diameter of coolant holes 0.5 mm
Pitch circle of coolant holes 1.6 mm
Diameter 6.30 mm
Sintered rods, 2 helical coolant holes
Nominal pitchOrdering code
20
RRK2 1430/7,0/2,0/76,2 14,3 7,0 2,00 76,2 265 x
RRK2 1430/6,7/1,8/76,2 14,3 6,7 1,80 76,2 265 x
RRK2 1430/7,2/1,6/70,7 14,3 7,2 1,60 70,7 325 x
RRK2 1630/8,6/2,5/87,1 16,3 8,6 2,50 87,1 280 x
RRK2 1630/8,0/2,0/87,1 16,3 8,0 2,00 87,1 280 x
RRK2 1630/8,4/2,0/81,6 16,3 8,4 2,00 81,6 325 x
RRK2 1830/9,7/2,8/98,0 18,3 9,7 2,80 98,0 330 x
RRK2 1830/9,0/2,3/98,0 18,3 9,0 2,30 98,0 330 x
RRK2 1830/9,6/2,2/92,5 18,3 9,6 2,20 92,5 325 x
RRK2 2030/10,7/3,2/108,8 20,3 10,7 3,20 108,8 330 x
RRK2 2030/10,0/2,5/108,8 20,3 10,0 2,50 108,8 330 x
RRK2 2030/10,4/2,5/103,4 20,3 10,4 2,50 103,4 325 x
RRK2 2230/11,7/3,2/119,7 22,3 11,7 3,20 119,7 330 r
RRK2 2530/11,5/3,5/119,0 25,3 11,5 3,50 119,0 330 r
RRK2 2530/12,0/2,5/119,0 25,3 12,0 2,50 119,0 330 x
D
[mm]
D1
[mm]
d
[mm]
[mm]
L
[mm]TSM33
K20-K40
MG18K20-K40
Sintered rods with 2 helical coolant holesin multiple lengths for tools with unifi ed shank
x= stock item
r= limited stock or upon request
Other grades and dimensions upon request
RRK2 - rods:For the production of DIN tools and special tools
RRK2 1830/9,7/2,8/98,0
Nominal pitch of coolant holes 98.0 mm
Diameter of coolant holes 2.8 mm
Pitch circle of coolant holes 9.7 mm
Diameter 18.30 mm
Sintered rods, 2 helical coolant holes
Nominal pitchOrdering code
21
D
[mm]
D1
[mm]
d
[mm]
[mm]
L
[mm]
TSM33K20-K40
MG18K20-K40
SBR2 0630/1,9/0,7/22,5 6,3 1,90 0,70 22,5 330 x
SBR2 0630/2,0/0,5/22,5 6,3 2,00 0,50 22,5 325 x
SBR2 0630/1,9/0,7/23,0 6,3 1,90 0,70 23,0 325 x
SBR2 0730/2,3/0,7/26,2 7,3 2,30 0,70 26,2 325 r
SBR2 0830/2,3/0,7/27,2 8,3 2,30 0,70 27,2 330 x
SBR2 0830/2,9/0,7/30,0 8,3 2,90 0,70 30,0 325 x
SBR2 0930/3,0/0,7/33,7 9,3 3,00 0,70 33,7 325 x
SBR2 1050/2,7/0,8/37,0 10,5 2,70 0,80 35,4 330 x
SBR2 1030/3,2/0,8/37,4 10,3 3,20 0,80 37,4 325 x
SBR2 1080/3,5/0,8/39,3 10,8 3,50 0,80 39,3 330 r
SBR2 1130/3,2/0,8/41,2 11,3 3,20 0,80 41,2 325 r
SBR2 1250/3,7/1,0/46,3 12,5 3,70 1,00 46,3 330 x
SBR2 1230/4,0/0,9/44,9 12,3 4,00 0,90 44,9 325 x
SBR2 1320/4,4/1,0/48,7 13,2 4,40 1,00 48,7 325 r
SBR2 1450/4,8/1,3/54,4 14,5 4,80 1,30 54,4 330 x
SBR2 1430/4,65/1,1/52,4 14,3 4,65 1,10 52,4 325 x
Sintered rods with 2 helical coolant holesfor stepped tools
Helix angle
x= stock item
r= limited stock or upon request
Other grades and dimensions upon request
SBR2 - rods:Due to their smaller pitch circle and a pitch of ~ 40°
they are suitable for the production of stepped tools
SBR2 0630/1,9/0,7/23,0
Nominal pitch of coolant holes 23.0 mm
Diameter of coolant holes 0.7 mm
Pitch circle of coolant holes 1.9 mm
Diameter 6.30 mm
Sintered rods, 2 helical coolant holes
Nominal pitch
Ordering code
22
SBR2 1480/4,9/1,1/54,4 14,8 4,90 1,10 54,4 330 r
SBR2 1530/4,9/1,2/56,1 15,3 4,90 1,20 56,1 325 r
SBR2 1650/5,7/1,5/62,0 16,5 5,70 1,50 62,0 330 x
SBR2 1630/5,5/1,2/59,9 16,3 5,50 1,20 59,9 325 x
SBR2 1730/5,75/1,3/63,6 17,3 5,75 1,30 63,6 325 r
SBR2 1850/6,3/1,7/74,2 18,5 6,30 1,70 74,2 330 x
SBR2 1830/6,25/1,5/67,4 18,3 6,25 1,50 67,4 325 x
SBR2 1930/6,5/1,5/71,1 19,3 6,50 1,50 71,1 325 r
SBR2 2050/7,0/1,7/84,3 20,5 7,00 1,70 84,3 330 x
SBR2 2030/7,1/1,5/74,9 20,3 7,10 1,50 74,9 325 x
SBR2 2130/7,4/1,6/78,6 21,3 7,40 1,60 78,6 325 r
SBR2 2230/7,7/1,7/82,4 22,3 7,70 1,70 82,4 325 r
SBR2 2530/7,7/1,75/93,6 25,3 7,70 1,75 93,6 330 x
SBR2 2530/7,7/1,7/95,85 25,3 7,70 1,70 95,85 325 x
D
[mm]
D1
[mm]
d
[mm]
[mm]
L
[mm]
TSM33K20-K40
MG18K20-K40
Sintered rods with 2 helical coolant holesfor stepped tools
Helix angle
SBR2 1650/5,7/1,5/62,0
Nominal pitch of coolant holes 62.0 mm
Diameter of coolant holes 1.5 mm
Pitch circle of coolant holes 5.7 mm
Diameter 16.50 mm
Sintered rods, 2 helical coolant holes
SBR2 - rods:Due to their smaller pitch circle and a pitch of ~ 40°
they are suitable for the production of stepped tools
x= stock item
r= limited stock or upon request
Other grades and dimensions upon request
Nominalpitch
Ordering code
23
D
[mm]
D1
[mm]
d
[mm]
[mm]
L
[mm]
TSM33K20-K40
MG18K20-K40
RRK3 0530/2,5/0,5/27,2 5,3 2,5 0,50 27,20 325 x
RRK3 0630/3,0/0,6/32,6 6,3 3,0 0,60 32,60 325 x
RRK3 0630/2,7/0,8/32,7 6,3 2,7 0,80 32,70 330 x
RRK3 0730/3,5/0,65/38,1 7,3 3,5 0,65 38,10 325 x
RRK3 0830/3,7/0,8/43,5 8,3 3,7 0,80 43,50 330 x
RRK3 0830/4,0/0,75/43,5 8,3 4,0 0,75 43,50 325 x
RRK3 0930/4,3/0,9/49,0 9,3 4,3 0,90 49,00 330 r
RRK3 0930/4,35/0,9/49,0 9,3 4,4 0,90 49,00 325 x
RRK3 1030/4,8/0,9/54,4 10,3 4,8 0,90 54,40 330 x
RRK3 1030/4,9/1,0/54,4 10,3 4,9 1,00 54,40 325 x
RRK3 1130/5,5/1,1/59,9 11,3 5,5 1,10 59,90 330 r
RRK3 1130/5,5/1,1/59,9 11,3 5,5 1,10 59,90 325 x
RRK3 1230/6,0/1,1/65,3 12,3 6,0 1,10 65,30 325 x
RRK3 1230/6,3/1,3/65,3 12,3 6,3 1,30 65,30 330 x
RRK3 1330/6,5/1,3/70,7 13,3 6,5 1,30 70,70 325 x
RRK3 1330/6,9/1,4/70,7 13,3 6,9 1,40 70,70 330 r
RRK3 1430/7,1/1,3/76,2 14,3 7,1 1,30 76,20 325 x
Sintered rods with 3 helical coolant holes
Helix angle
RRK3 - rods:For the production of DIN tools and special tools with a 30° helix angle
x= stock item
r= limited stock or upon request
Other grades and dimensions upon request
RRK3 0930/4,3/0,9/49,0
Nominal pitch of coolant holes 49.0 mm
Diameter of coolant holes 0.9 mm
Pitch circle of coolant holes 4.3 mm
Diameter 9.30 mm
Sintered rods, 3 helical coolant holes
Nominalpitch
Ordering code
24
D
[mm]
D1
[mm]
d
[mm] [mm]
L
[mm]
TSM33K20-K40
MG18K20-K40
RRK3 1430/7,6/1,5/76,2 14,3 7,6 1,50 76,20 330 x
RRK3 1530/7,7/1,5/81,6 15,3 7,7 1,50 81,60 325 r
RRK3 1630/8,3/1,5/87,0 16,3 8,3 1,50 87,00 325 x
RRK3 1630/8,6/1,7/87,1 16,3 8,6 1,70 87,10 330 x
RRK3 1730/8,9/1,6/92,5 17,3 8,9 1,60 92,50 325 r
RRK3 1830/9,6/1,7/97,9 18,3 9,6 1,70 97,90 325 x
RRK3 1830/9,7/1,7/98,0 18,3 9,7 1,70 98,00 330 x
RRK3 1930/10,1/1,9/103,4 19,3 10,1 1,90 103,40 330 r
RRK3 1930/10,1/1,8/103,4 19,3 10,1 1,80 103,40 325 r
RRK3 2030/10,4/2,0/108,8 20,3 10,4 2,00 108,80 325 x
RRK3 2030/10,7/2,0/108,8 20,3 10,7 2,00 108,80 330 x
RRK3 2130/11,5/2,0/114,2 21,3 11,5 2,00 114,20 325 r
RRK3 2230/11,7/2,0/119,7 22,3 11,7 2,00 119,70 330 r
RRK3 2230/12,0/2,0/119,7 22,3 12,0 2,00 119,70 325 r
RRK3 2530/11,5/2,2/119,0 25,3 11,5 2,20 119,00 330 x
Sintered rods with 3 helical coolant holes
Helix angle
RRK3 - rods:For the production of DIN tools and special tools with a 30° helix angle
RRK3 1830/9,7/1,7/98,0
Nominal pitch of coolant holes 98.0 mm
Diameter of coolant holes 1.7 mm
Pitch circle of coolant holes 9.7 mm
Diameter 18.30 mm
Sintered rods, 3 helical coolant holes
x= stock item
r= limited stock or upon request
Other grades and dimensions upon request
Nominalpitch
Ordering code
25
D
[mm]
D1
[mm]
d
[mm] [mm]
L
[mm]
MG18K20-K40
SBR3 0630/2,3/0,5/22,5 6,3 2,3 0,5 22,5 325 x
SBR3 0730/2,3/0,5/26,2 7,3 2,3 0,5 26,2 325 r
SBR3 0830/2,9/0,7/30,0 8,3 2,9 0,7 30,0 325 x
SBR3 0930/3,0/0,7/33,7 9,3 3,0 0,7 33,7 325 r
SBR3 1030/3,5/0,75/37,4 10,3 3,5 0,75 37,4 325 x
SBR3 1130/3,7/0,8/41,2 11,3 3,7 0,8 41,2 325 r
SBR3 1230/4,0/0,9/44,9 12,3 4,0 0,9 44,9 325 x
SBR3 1330/4,5/1,0/48,7 13,3 4,5 1,0 48,7 325 r
SBR3 1430/4,65/1,2/52,4 14,3 4,65 1,2 52,4 325 x
SBR3 1530/4,9/1,2/56,1 15,3 4,9 1,2 56,1 325 r
SBR3 1630/5,5/1,2/59,9 16,3 5,5 1,2 59,9 325 x
SBR3 1730/5,75/1,3/63,6 17,3 5,75 1,3 63,6 325 r
SBR3 1830/6,25/1,5/67,4 18,3 6,25 1,5 67,4 325 x
SBR3 1930/6,5/1,5/71,1 19,3 6,5 1,5 71,1 325 r
SBR3 2030/7,1/1,5/74,9 20,3 7,1 1,5 74,9 325 x
SBR3 2130/7,4/1,6/78,6 21,3 7,4 1,6 78,6 325 r
SBR3 2230/7,7/1,7/82,4 22,3 7,7 1,7 82,4 325 r
Sintered rods with 3 helical coolant holes
Helix angle
x= stock item
r= limited stock or upon request
Other grades and dimensions upon request
SBR3 - rods:Due to their smaller pitch circle and a pitch of ~ 40°
they are suitable for the production of stepped tools
for stepped tools
SBR3 0830/2,9/0,7/30,0
Nominal pitch of coolant holes 30.0 mm
Diameter of coolant holes 0.7 mm
Pitch circle of coolant holes 2.9 mm
Diameter 8.30 mm
Preground rods, 3 helical coolant holes
Nominalpitch
Ordering code
26
D
[mm]
D1
[mm]
d
[mm]
L=330
TSM20K10-K30
L=325
MG18K20-K40
RRG2 0420/1,5/0,9 4,20 1,50 0,90 x x
RRG2 0420/1,8/0,8 4,20 1,80 0,80 r
RRG2 0520/1,8/0,9 5,20 1,80 0,90 r
RRG2 0520/2,0/0,9 5,20 2,00 0,90 x r
RRG2 0620/1,0/0,5 6,20 1,00 0,50 x
RRG2 0620/1,5/0,9 6,20 1,50 0,90 r x
RRG2 0620/1,7/0,9 6,20 1,70 0,90 r r
RRG2 0620/2,0/0,9 6,20 2,00 0,90 x
RRG2 0620/2,0/1,0 6,20 2,00 1,00 r
RRG2 0620/2,3/0,9 6,20 2,30 0,90 x
RRG2 0620/2,4/1,2 6,20 2,40 1,20 r
RRG2 0620/2,6/0,9 6,20 2,60 0,90 r
RRG2 0620/3,0/1,0 6,20 3,00 1,00 x
RRG2 0620/3,0/1,2 6,20 3,00 1,20 x x
RRG2 0720/2,0/0,9 7,20 2,00 0,90 r
RRG2 0720/2,0/1,0 7,20 2,00 1,00 r
RRG2 0720/3,0/0,9 7,20 3,00 0,90 r
RRG2 0720/3,0/1,2 7,20 3,00 1,20 r
RRG2 0720/3,5/1,0 7,20 3,50 1,00 r
RRG2 0820/1,1/0,5 8,20 1,10 0,50 x
RRG2 0820/2,0/0,8 8,20 2,00 0,80 x
RRG2 0820/2,0/0,9 8,20 2,00 0,90 r
RRG2 0820/2,0/1,0 8,20 2,00 1,00 r
RRG2 0820/2,6/1,2 8,20 2,60 1,20 x
RRG2 0820/2,6/0,9 8,20 2,60 0,90 x
RRG2 0820/2,7/1,3 8,20 2,70 1,30
RRG2 0820/3,3/1,1 8,20 3,30 1,10 r
RRG2 0820/3,4/1,0 8,20 3,40 1,00 r
RRG2 0820/3,5/1,5 8,20 3,50 1,50 r
RRG2 0820/3,5/1,5 8,20 3,50 1,50 r
RRG2 0820/4,0/0,9 8,20 4,00 0,90 r
RRG2 0820/4,0/1,0 8,20 4,00 1,00 x
Sintered rods with 2 straight coolant holes
Ordering code
27
D
[mm]
D1
[mm]
d
[mm]
L=330
TSM20K10-K30
L=325
MG18K20-K40
RRG2 0920/2,0/0,9 9,20 2,00 0,90 r
RRG2 0920/2,6/1,2 9,20 2,60 1,20 r
RRG2 0920/2,7/1,3 9,20 2,70 1,30 r
RRG2 0920/3,5/1,5 9,20 3,50 1,50 r r
RRG2 0920/3,8/1,2 9,20 3,80 1,20 r
RRG2 0920/4,0/1,3 9,20 4,00 1,30 r
RRG2 1020/2,0/1,0 10,20 2,00 1,00 x
RRG2 1020/2,6/1,2 10,20 2,60 1,20 x
RRG2 1020/2,7/1,3 10,20 2,70 1,30 r
RRG2 1020/2,8/1,0 10,20 2,80 1,00 r
RRG2 1020/3,5/1,5 10,20 3,50 1,50 x r
RRG2 1020/3,8/1,2 10,20 3,80 1,20 r
RRG2 1020/4,0/1,4 10,20 4,00 1,40 x
RRG2 1020/4,2/1,4 10,20 4,20 1,40 r
RRG2 1020/5,0/1,2 10,20 5,00 1,20 x x
RRG2 1020/5,2/1,4 10,20 5,20 1,40 x
RRG2 1120/3,5/1,5 11,20 3,50 1,50 r
RRG2 1120/4,6/1,5 11,20 4,60 1,50 r
RRG2 1120/5,0/1,2 11,20 5,00 1,20 r
RRG2 1120/5,0/2,0 11,20 5,00 2,00 x
RRG2 1120/5,2/1,4 11,20 5,20 1,40 r
RRG2 1220/2,6/1,2 12,20 2,60 1,20 x
RRG2 1220/3,5/1,5 12,20 3,50 1,50 x x
RRG2 1220/3,5/1,5-415 12,20 3,50 1,50 xL=415
RRG2 1220/3,7/1,3 12,20 3,70 1,30 r
RRG2 1220/4,8/1,5 12,20 4,80 1,50 r
RRG2 1220/5,0/2,0 12,20 5,00 2,00 r x
RRG2 1220/6,0/1,5 12,20 6,00 1,50 x
RRG2 1220/6,0/2,5-415 12,20 6,00 2,50 rL=415
RRG2 1220/6,2/1,5 12,20 6,20 1,50 r
RRG2 1220/6,2/2,0 12,20 6,20 2,00 x
Sintered rods with 2 straight coolant holes
Ordering code
28
D
[mm]
D1[mm]
d
[mm]
L=330
TSM20K10-K30
L=325
MG18K20-K40
RRG2 1320/3,5/1,5 13,20 3,50 1,50 r
RRG2 1320/5,4/2,0 13,20 5,40 2,00 r
RRG2 1320/6,2/2,0 13,20 6,20 2,00 r
RRG2 1420/3,5/1,5 14,20 3,50 1,50 x
RRG2 1420/5,0/1,7 14,20 5,00 1,70 x
RRG2 1420/5,0/2,0 14,20 5,00 2,00 r r
RRG2 1420/5,8/2,0 14,20 5,80 2,00 x
RRG2 1420/7,0/2,0-241 14,20 7,00 2,00 x
RRG2 1420/7,0/2,0-345 14,20 7,00 2,00 x
RRG2 1520/5,0/2,0 15,20 5,00 2,00 x
RRG2 1520/6,2/2,5 15,20 6,20 2,50 r
RRG2 1520/7,0/2,0 15,20 7,00 2,00 r
RRG2 1620/3,5/1,5 16,20 3,50 1,50 x
RRG2 1620/5,0/1,5 16,20 5,00 1,50 r
RRG2 1620/5,0/1,7 16,20 5,00 1,70 r
RRG2 1620/5,0/2,0 16,20 5,00 2,00 x
RRG2 1620/6,2/2,0-400 16,20 6,20 2,00 x
RRG2 1620/6,6/2,0 16,20 6,60 2,00 r
RRG2 1620/6,6/2,5 16,20 6,60 2,50 x
RRG2 1620/7,0/2,5 16,20 7,00 2,50 r
RRG2 1620/8,0/2,0-415 16,20 8,00 2,00 x r
RRG2 1720/6,2/2,0 17,20 6,20 2,00 x
RRG2 1720/7,0/2,5 17,20 7,00 2,50 r
RRG2 1720/8,0/2,0 17,20 8,00 2,00 r
RRG2 1820/5,0/2,0 18,20 5,00 2,00 x
RRG2 1820/6,0/2,0 18,20 6,00 2,00 x
RRG2 1820/6,3/2,0 18,20 6,30 2,00 r
RRG2 1820/7,0/2,0 18,20 7,00 2,00 x
RRG2 1820/7,0/2,5 18,20 7,00 2,50 r
RRG2 1820/7,5/2,0 18,20 7,50 2,00 r
RRG2 1820/7,5/2,5 18,20 7,50 2,50 r
RRG2 1820/9,0/2,0 18,20 9,00 2,00 x x
Sintered rods with 2 straight coolant holes
Ordering code
29
D
[mm]
D1[mm]
d
[mm]
L=330
TSM20K10-K30
L=325
MG18K20-K40
RRG2 1920/6,2/2,0 19,20 6,20 2,00 r
RRG2 1920/6,3/2,0 19,20 6,30 2,00 x
RRG2 1920/7,9/2,5 19,20 7,90 2,50 r
RRG2 2020/3,5/1,5 20,20 3,50 1,50 x
RRG2 2020/6,0/2,0 20,20 6,00 2,00 x x
RRG2 2020/6,3/2,0 20,20 6,30 2,00 r
RRG2 2020/7,0/2,5 20,20 7,00 2,50 r
RRG2 2020/8,2/2,0 20,20 8,20 2,00 r
RRG2 2020/8,2/2,5 20,20 8,20 2,50 r x
RRG2 2020/10,0/2,5 20,20 10,00 2,50 x x
RRG2 2120/6,2/2,0 21,20 6,20 2,00 r
RRG2 2120/7,0/2,3 21,20 7,00 2,30 r
RRG2 2220/7,0/2,0 22,20 7,00 2,00 r
RRG2 2220/7,0/2,3 22,20 7,00 2,30 x
RRG2 2220/7,0/2,5 22,20 7,00 2,50 r
RRG2 2220/10,5/3,0 22,20 10,50 3,00 r
RRG2 2540/6,2/2,0 25,40 6,20 2,00 x
RRG2 2540/8,0/2,0 25,40 8,00 2,00 r
RRG2 2540/10,0/2,5 25,40 10,00 2,50 x
RRG2 2540/12,0/3,0 25,40 12,00 3,00 r
RRG2 1220/5,0/2,0
Nominal pitch of coolant holes 2.0 mm
Diameter of coolant holes 5.0 mm
Diameter 12.20 mm
Sintered rods, 2 straight coolant holes
Sintered rods with 2 straight coolant holes
x= stock item
r= limited stock or upon request
Other grades and dimensions upon request
Ordering code
30
D
[mm]
d
[mm]
L=330 L=325
MG18K20-K40
TSF44K10-K30
TSM20K10-K30
RRG1 0495/0,6 4,95 0,6 x
RRG1 0630/1,0 6,30 1,0 x
RRG1 0645/1,0 6,45 1,0 x x
RRG1 0645/1,5 6,45 1,5 x
RRG1 0730/1,1 7,30 1,1 r
RRG1 0830/1,3 8,30 1,3 x
RRG1 0855/1,3 8,55 1,3 x x
RRG1 0855/2,0 8,55 2,0 x x
RRG1 0930/1,3 9,30 1,3 r
RRG1 1030/2,0 10,30 2,0 x
RRG1 1055/1,3 10,55 1,3 x x
RRG1 1055/2,0 10,55 2,0 x x
RRG1 1130/2,0 11,30 2,0 r
RRG1 1155/2,0 11,55 2,2 r
RRG1 1230/2,0 12,30 2,0 x
RRG1 1255/2,0 12,55 2,0 x x
RRG1 1330/2,0 13,30 2,0 r
RRG1 1430/2,0 14,30 2,0 x
RRG1 1470/2,0 14,70 2,0 x x
RRG1 1630/2,0 16,30 2,0 x
RRG1 1670/2,0 16,70 2,0 x x
RRG1 1730/2,0 17,30 2,0 r
RRG1 1750/2,0 17,50 2,0 r r
RRG1 1830/3,0 18,30 3,0 x
RRG1 1870/3,0 18,70 3,0 x x
RRG1 2030/3,0 20,30 3,0 x
RRG1 2070/3,0 20,70 3,0 x x
RRG1 2230/3,0 22,30 3,0 x
Sintered rods with 1 straight coolant hole
RRG1 120/2,0
Hole diameter 2.0 mm
Diameter 12.0 mm
Sintered rods with central coolant hole
x= stock itemr= limited stock or upon requestOther grades and dimensions upon request
Ordering code
31
H
[mm]
S
[mm]
L
[mm]
TSM20K10-K30
TSM33K20-K40
MG18K20-K40
FR 2.5 1.5 2,50 1,50 325 r
FR 3 1.5 3,00 1,50 325 r
FR 32 3,00 2,00 325 x
FR 32 3,30 2,30 310 r x
FR 3.5 1.5 3,50 1,50 325 r
FR 4 1.7 4,00 1,70 325 r
FR 42 4,00 2,00 325 x
FR 43 4,00 3,00 325 r
FR 42 4,30 2,30 310 x
FR 5 1.5 5,00 1,50 325 r
FR 5 1.7 5,00 1,70 325 r
FR 52 5,00 2,00 325 x
FR 5 2.7 5,00 2,70 325 r
FR 53 5,00 3,00 325 x
FR 54 5,00 4,00 325 r
FR 52 5,30 2,30 310 r x
FR 53 5,30 3,30 310 r x
FR 6 1.7 6,00 1,70 325 r
FR 62 6,00 2,00 325 x
FR 63 6,00 3,00 325 x
FR 64 6,00 4,00 325 r
FR 62 6,30 2,30 310 x
FR 63 6,30 3,30 310 x
FR 64 6,30 4,30 310 x
FR 6.5 1.5 6,50 1,50 325 r
FR 72 7,00 2,00 325 r
FR 73 7,00 3,00 325 r
FR 74 7,00 4,00 325 r
Sintered rectangular rods
Ordering code
32
H
[mm]
S
[mm]
L
[mm]
TSM20K10-K30
TSM33K20-K40
MG18K20-K40
FR 8 1.5 8,00 1,50 325 r
FR 82 8,00 2,00 325 x
FR 83 8,00 3,00 325 x
FR 84 8,00 4,00 325 x
FR 86 8,00 6,00 325 r
FR 82 8,30 2,30 310 r x
FR 83 8,30 3,30 310 x
FR 84 8,30 4,30 310 x
FR 92 9,00 2,00 325 r
FR 93 9,00 3,00 325 r
FR 9 3.5 9,00 3,50 325 r
FR 94 9,00 4,00 325 r
FR 10 1.5 10,00 1,50 325 r
FR 102 10,00 2,00 325 r
FR 103 10,00 3,00 325 x
FR 104 10,00 4,00 325 x
FR 105 10,00 5,00 325 x
FR 106 10,00 6,00 325 x
FR 102 10,30 2,30 310 r
FR 103 10,30 3,30 310 x
FR 104 10,30 4,30 310 x
FR 105 10,30 5,30 310 x
FR 106 10,30 6,30 310 x
FR 113 11,00 3,00 325 r
FR 112 11,30 2,30 310 x
Sintered rectangular rods
x= stock item
r= limited stock or upon request
Other grades and dimensions upon request
Ordering code
33
H
[mm]
S
[mm]
L
[mm]
TSM20K10-K30
TSM33K20-K40
MG18K20-K40
FR 122 12,00 2,00 325 r
FR 123 12,00 3,00 325 x
FR 124 12,00 4,00 325 x
FR 125 12,00 5,00 325 r
FR 122 12,30 2,30 310 x
FR 124 12,30 4,30 310 x
FR 125 12,30 5,30 310 r
FR 126 12,30 6,30 310 x
FR 128 12,30 8,30 310 r
FR 1210 12,30 10,30 310 x
FR 133 13,00 3,00 325 r
FR 134 13,00 4,00 325 r
FR 135 13,00 5,00 325 r
SR 133 13,30 3,30 310 x
FR 134 13,30 4,30 310 x
FR 135 13,30 5,30 310 x
FR 136 13,30 6,30 310 x
FR 142 14,00 2,00 325 x
FR 143 14,00 3,00 325 x
FR 142 14,30 2,30 310 x
FR 152 15,00 2,00 325 r
FR 153 15,00 3,00 325 r
FR 154 15,00 4,00 325 r
FR 155 15,00 5,00 325 r
FR 156 15,00 6,00 325 r
Sintered rectangular rods
x= stock item
r= limited stock or upon request
Other grades and dimensions upon request
Ordering code
34
H
[mm]
S
[mm]
L
[mm]
TSM20K10-K30
TSM33K20-K40
MG18K20-K40
FR 162 16,00 2,00 325 x
FR 163 16,00 3,00 325 x
FR 164 16,00 4,00 325 x
FR 165 16,00 5,00 325 x
FR 162 16,30 2,30 310 x
FR 163 16,30 3,30 310 x
FR 164 16,30 4,30 310 x
FR 165 16,30 5,30 310 x
FR 168 16,30 8,30 310 x
FR 1610 16,30 10,30 310 x
FR 173 17,00 3,00 325 r
FR 182 18,00 2,00 325 r
FR 183 18,00 3,00 325 r
FR 184 18,00 4,00 325 r
FR 202 20,00 2,00 325 r
FR 203 20,00 3,00 325 x
FR 204 20,00 4,00 325 r
FR 205 20,00 5,00 325 x
FR 206 20,00 6,00 325 x
FR 207 20,00 7,00 325 r
FR 208 20,00 8,00 325 r
FR 2012 20,00 12,00 325 r
FR 203 20,30 3,30 310 x
FR 204 20,30 4,30 310 x
FR 205 20,30 5,30 310 r x
FR 206 20,30 6,30 310 x
FR 214 21,00 4,00 325 r
FR 222 22,00 2,00 325 r
FR 223 22,00 3,00 325 r
FR 224 22,00 4,00 325 r
Sintered rectangular rods
Ordering code
35
H
[mm]
S
[mm]
L
[mm]
TSM20K10-K30
TSM33K20-K40
MG18K20-K40
FR 282 28,00 2,00 325 r
FR 283 28,00 3,00 325 r
FR 284 28,00 4,00 325 r
FR 302 30,00 2,00 325 r
FR 303 30,00 3,00 325 r
FR 304 30,00 4,00 325 r
FR 305 30,00 5,00 325 r
FR 306 30,00 6,00 325 r
FR 323 32,00 3,00 325 r
FR 353 35,00 3,00 325 r
FR 355 35,00 5,00 325 r
Sintered rectangular rods
r= limited stock or upon request
Other grades and dimensions upon request
FR 353
Thickness 3.0 mm
Height 35.0 mm
Sintered rectangular rod
Ordering code
36
S
[mm]
L=310
TSM33K20-K40
L=325
MG18K20-K40
SR 3 3,3 x
SR 4 4,0 r
SR 4 4,3 x
SR 5 5,3 r
SR 6 6,0 r
SR 6 6,3 x
SR 8 8,0 r
SR 8 8,3 x
SR 10 10,0 r
SR 10 10,3 x
SR 12 12,0 r
SR 12 12,3 x
SR 14 14,0 r
Sintered square rods
SR 4-325
Rod length 325.0 mm
Lateral length 4.0 mm
Sintered square rod
x= stock item
r= limited stock or upon request
Other grades and dimensions upon request
Ordering code
37
ISO K10
R
R12 r
R16 r
R19 r
R22 r
R25 r
R30 r
T
T12 r
T16 r
T19 r
T22 r
T25 r
U
U12 r
U16 r
U19 r
U22 r
U25 r
R
R 16x30 r
R 19x30 r
R 19x45 r
R 22x56 r
R 25x66 r
R 30x70 r
R B C D E G H J
CERATIZITTips for reamers
Brazing tips according to ISO, DIN 4950 ÖNORM M 4370 upon request
Ordering codeForm R - T - U - V
DIN 8011 special lengths
38
t
[mm]
s
[mm]
l
[mm]
H20TK20
SF-A1 4,5 3,0 8,0 ø16, ø20 r
SF-A2 4,5 3,0 11,2 ø16, ø20 r
SF-B1 5,5 3,5 8,0 ø25, ø28 r
SF-B2 5,5 3,5 12,0 ø25, ø28 r
SF-C1 7,0 4,0 9,5 ø32 - ø40 r
SF-C2 7,0 4,0 14,3 ø32 - ø40 r
SF-D1 8,5 4,0 9,5 ø50 - ø100 r
SF-D2 8,5 4,0 14,3 ø50 - ø100 r
t
[mm]
s
[mm]
l
[mm]
H20TK20
SF-A3 4,5 3,5 5,0 ø16, ø20 r
SF-B3 5,5 3,5 5,0 ø25, ø28 r
SF-C3 7,0 4,0 6,0 ø32 - ø40 r
SF-D3 8,5 4,0 6,0 ø50 - ø100 r
SFBrazing tips for spiral fl uted milling cutters
and long edge milling cutters
Front cutters
Circumference cutters
r= available grades
Other grades and dimensions upon request
Ordering code
Ordering code
For millingcutters
For millingcutters
Front cutters
Circumference
cutters
www.ceratizit.com
Sales Companies
Austria
CERATIZIT Austria Gesellschaft m.b.H.
A-6600 Reutte/Tyrol
Tel.: +43 (5672) 200-0
Fax: +43 (5672) 200-502
E-Mail: [email protected]
Bulgaria
CERATIZIT Bulgaria AG
Boulevard Stoletov 157
BG-5301 Gabrovo
Tel: +359 (66) 438-11
Fax: +359 (66) 801 608
E-Mail: [email protected]
China
CERATIZIT China Ltd.
Room 1201-1204
Hollywood Centre
233 Hollywood Rd., Sheung Wan
Hong Kong
Tel.: +852 (2542)-1838
Fax: +852 (2854) 3777
E-Mail: [email protected]
France
CERATIZIT France Sarl
Offi ce Pontoise
20, Rue Lavoisier
F-95300 Pontoise
Tel.: +33 (1) 3433-3180
Fax: +33 (1) 3030-9339
E-Mail: [email protected]
CERATIZIT France Sarl
Offi ce Lyon
Parc de L’Artillerie
5, Espace Henri Vallée
F-69007 Lyon
Tel.: +33 (4) 72 76 86 50
Fax: +33 (4) 72 76 86 51
E-Mail: [email protected]
Germany
CERATIZIT Deutschland GmbH
Offi ce Langenfeld
Hans-Böckler-Straße 10
D-40764 Langenfeld
Tel.: +49 (2173) 97 25-0
Fax: +49 (2173) 97 25-25
E-Mail: [email protected]
CERATIZIT Deutschland GmbH
Offi ce Bad Urach
Schützenstraße 29
D-72574 Bad Urach
Tel.: +49 (7125) 1501-0
Fax: +49 (7125) 8594
E-Mail: [email protected]
CERATIZIT Horb GmbH
Stadionstraße
D-72160 Horb
Tel.: +49 (7451) 522 0
Fax: +49 (7451) 522 288
E-Mail: [email protected]
CERATIZIT Logistik GmbH
Daimlerstraße 70
D-87437 Kempten
Tel.: +49 (831) 570 11-0
Fax: +49 (831) 570 11-3811
Great Britain
CERATIZIT UK Ltd.
Cliff Lane
Grappenhall
Warrington WA4 3JX
Tel.: +44 (1925) 261-161
Fax: +44 (1925) 267-933
E-Mail: [email protected]
India
CERATIZIT India Pvt. Ltd.
58, Motilal Gupta Road
Barisha
IN-700 008 Kolkata
Tel.: +91 (33) 2494-5435
Fax: +91 (33) 2494-1472
Telex: 021 8142 ihm in
E-Mail: [email protected]
Italy
CERATIZIT Italia SpA
Piazza F. Martelli, 7
I-20162 Milano
Tel.: +39 (02) 6441-111
Fax: +39 (02) 6611-6040
E-Mail: [email protected]
Headquarters: CERATIZIT S.A.
Main site Luxembourg
CERATIZIT Luxembourg Sarl
Route de Holzem
L-8232 Mamer
Tel.: +352 312 085-1
Fax: +352 311 911
E-Mail: [email protected]
Main site Austria
CERATIZIT Austria Gesellschaft m.b.H.
A-6600 Reutte/Tyrol
Tel.: +43 (5672) 200-0
Fax: +43 (5672) 200-502
E-Mail: [email protected]
Japan
CERATIZIT Japan Ltd.
3-13-9, Mizuho
Shizuoka 421 – 0115
Tel.: +81 (54) 268 1060
Fax: +81 (54) 257 8181
E-Mail: [email protected]
Luxembourg
CERATIZIT Luxembourg Sarl
Route de Holzem
L-8232 Mamer
Tel.: +352 312 085-1
Fax: +352 311 911
E-Mail: [email protected]
Netherlands
CERATIZIT Nederland B.V.
Bergrand 224
NL-4707 At Roosendaal
Tel.: +31 (165) 55 08 00
Fax: +31 (165) 55 61 76
E-Mail: [email protected]
Spain
CERATIZIT Ibérica SL
Offi ce Pozuelo
Vía de las Dos Castillas, 9c
Portal 2, Bajo B
E-28224 Pozuelo (Madrid)
Tel.: +34 (91) 351-0609
Fax: +34 (91) 351-2813
E-Mail: [email protected]
CERATIZIT Ibérica SL
Offi ce Bilbao
Avda. Mazarredo 41 1 Izqda.
E-48009 Bilbao
Tel.: +34 (944) 23 71 18
Fax: +34 (944) 23 97 18
E-Mail: [email protected]
Switzerland
CERATIZIT Schweiz AG
Solothurnstrasse 68
CH-2504 Biel
Tel.: +41 (32) 344 93 93
Fax: +41 (32) 344 93 94
E-Mail: [email protected]
USA
CERATIZIT USA Inc.
777 Old Clemson Road
Columbia
South Carolina 29229
Toll free: +1 (800) 334 1165
Tel.: +1 (803) 736 1900
Fax: +1 (803) 736 1902
E-Mail: [email protected]
www.ceratizit.com - just a click.
We
rese
rve
the
right
to m
ake
tech
nica
l cha
nges
for
impr
ovem
ent
of th
e pr
oduc
t.
147/2 EN 10.03