Guidlines BSc Elect Engg Final Year Project Report Writing
-
Upload
osama-tahir -
Category
Documents
-
view
215 -
download
0
Transcript of Guidlines BSc Elect Engg Final Year Project Report Writing
-
7/28/2019 Guidlines BSc Elect Engg Final Year Project Report Writing
1/18
i
University of Engineering & Technology, Taxila.
Department of Electrical Engineering
Project Report Format
Prepared by:
Dr. Gulistan RajaAssistant Professor
Approved by:
Prof. Dr. Tahir Nadeem Malik
Chairman EED
June 2011
mailto:[email protected]:[email protected]:[email protected] -
7/28/2019 Guidlines BSc Elect Engg Final Year Project Report Writing
2/18
ii
PROJECT TITLE (in Caps)
(HARD BINDING PAGE)
Supervisor
Name
Designation
Submitted By
Name of Project Member1 07-EE-1
Name of Project Member2 07-EE-2
DEPARTMENT OF ELECTRICAL ENGINEERINGFACULTY OF ELECTRONICS & ELECTRICAL ENGINEERING
UNIVERSITY OF ENGINEERING AND TECHNOLOGY
TAXILA.
Month Year
-
7/28/2019 Guidlines BSc Elect Engg Final Year Project Report Writing
3/18
iii
PROJECT TITLE (in Caps)
Supervisor
NameDesignation
Submitted By
Name of Project Member1 07-EE-1
Name of Project Member2 07-EE-2
A Project Report submitted in partial fulfillment of the
requirements for the award of Bachelors Degree in
Electrical Engineering
DEPARTMENT OF ELECTRICAL ENGINEERING
FACULTY OF ELECTRONICS & ELECTRICAL ENGINEERINGUNIVERSITY OF ENGINEERING AND TECHNOLOGY
TAXILA.
Month Year
-
7/28/2019 Guidlines BSc Elect Engg Final Year Project Report Writing
4/18
iv
Undertaking
I/We certify that project work titled enter title of your project here is my/our own work.
No portion of the work presented in this project has been submitted in support of another
award or qualification either at this institution or elsewhere. Where material has been used
from other sources it has been properly acknowledged / referred.
Signature of Student 1
Name of Student 1
Registration No. of Student 1
Signature of Student 2
Name of Student 2
Registration No. of Student 2
-
7/28/2019 Guidlines BSc Elect Engg Final Year Project Report Writing
5/18
v
Acknowledgements
We would like to thank . guiding us in understanding the concepts
of ... We would like to thank all our teachers especially
. guiding us in solving our problems related to .. our project
supervisor ... his cooperation and support to bring this project to completion.
We would also like to thank our families and friends for their continuous encouragement and
moral support.
-
7/28/2019 Guidlines BSc Elect Engg Final Year Project Report Writing
6/18
vi
Abstract
NOTE: Write abstract here. The font of the entire document is Times New Roman size 12,
justified except headings with double line spacing.
The length of the abstract should not exceed 1 page at maximum
This project describes the implementation of..
-
7/28/2019 Guidlines BSc Elect Engg Final Year Project Report Writing
7/18
vii
Table of Contents
Undertaking___________________________________________________________________ iv
Acknowledgements _____________________________________________________________ v
Abstract ______________________________________________________________________ vi
Chapter 1 ________________________________________________________________ 1
Introduction___________________________________________________________________ 11 BACKGROUND ____________________________________________________________________ 1
1.1 Sub Heading1 ___________________________________________________________________ 11.2 Sub Heading2 ___________________________________________________________________ 11.3 Sub Heading3 ___________________________________________________________________ 1
2 WHAT IS ________________________________________________________________________ 1
Chapter 2 ________________________________________________________________ 2
Theory related to Project ________________________________________________________ 2
2.1 Statement ______________________________________________________________________ 22.2 Technique 1 ____________________________________________________________________ 22.3 Technique 2 ____________________________________________________________________ 22.4 Technique 3 _____________________________________________________________________
Chapter 3 ________________________________________________________________ 3
Implementation of Project _______________________________________________________33.1 MODEL AND NAMING CONVENTIONS ___________________________________________ 3
3.1.1 Heading of Name1 __________________________________________________________ 33.1.1.1 Sub Heading1 ______________________________________________________________ 3
3.1.2 Heading of Name2 __________________________________________________________ 33.1.3 Heading of Name3 __________________________________________________________ 33.1.4 Heading of Name3 __________________________________________________________ 3
Chapter 4 ________________________________________________________________ 4
Simulation Results _____________________________________________________________ 41 HEADING 1 _____________________________________________________________________ 42 HEADING 2 _____________________________________________________________________ 4
CONCLUSION ___________________________________________________________________________ 5FUTURE RECOMMENDATIONS ___________________________________________________________ 6
Appendix A _______________________________________________________________ 7
Title of Appendix ______________________________________________________________ 7
References ____________________________________________________________________ 8
Hard Copy I nf ormation _____________________________________________________ 9
-
7/28/2019 Guidlines BSc Elect Engg Final Year Project Report Writing
8/18
viii
Listof Figures
Figure 1Class diagram ...................................................................................................................................
-
7/28/2019 Guidlines BSc Elect Engg Final Year Project Report Writing
9/18
ix
Listof TablesTable: List of abc ...............................................................................................................................................
Table: List of xyz ..............................................................................................................................................
-
7/28/2019 Guidlines BSc Elect Engg Final Year Project Report Writing
10/18
1
Chapter 1
Introduction
1 BACKGROUND
1.1 Sub Heading1
Text here
1.2 Sub Heading2
abc xyz
1.3 Sub Heading3
Text..
.. .. ..
2 WHAT IS
Text here
New Line
NOTE: DRAW ALL DIAGRAMS IN MS VISIO FIGURE CAPTIONS BELOW FIGURE TABLE CAPTIONS ABOVE TABLE
-
7/28/2019 Guidlines BSc Elect Engg Final Year Project Report Writing
11/18
2
Chapter 2
Theory Related to Project
2.1 Statement
The . will be based on the ..
2.2 Technique 1
Explain Technique 1 present in literature here.
2.3 Technique 2
Explain Technique 2 present in literature here.
2.4 Technique 3
Explain Technique 3 present in literature here.
-
7/28/2019 Guidlines BSc Elect Engg Final Year Project Report Writing
12/18
3
Chapter 3
Implementation of Project
3.1 MODEL AND NAMING CONVENTIONS
Text here..
3.1.1 Heading of Name1
Text here..
3.1.1.1Sub Heading1
Text here
3.1.2 Heading of Name2
Text here
3.1.3 Heading of Name3
Text here
3.1.4 Heading of Name3
Text here
3.2 HEADING
Text here
-
7/28/2019 Guidlines BSc Elect Engg Final Year Project Report Writing
13/18
4
Chapter 4
Simulation Results
1 HEADING 1
Discuss simulation results of your project here
-
7/28/2019 Guidlines BSc Elect Engg Final Year Project Report Writing
14/18
5
Conclusion
We started the project with the objectives mentioned in the project statement and achieved all
of them. We have implemented
-
7/28/2019 Guidlines BSc Elect Engg Final Year Project Report Writing
15/18
6
Future Recommendations
We would like to recommend the following features to be incorporated in our developed
software ..
abc xyz
-
7/28/2019 Guidlines BSc Elect Engg Final Year Project Report Writing
16/18
7
Appendix A
Title of Appendix
Text here
Further appendixes can be inserted in the same format
-
7/28/2019 Guidlines BSc Elect Engg Final Year Project Report Writing
17/18
8
References
Write down references used for the proposal here. Wri te down the references in order ofpubl ication year with ol dest reference at top and latest at the bottom. Use the following
formatfor references.
Example Journal Paper:
[1]Didier Le Gall, MPEG: A video compression standard for multimedia applications,Communications ACM, vol. 34, no. 4, pp. 4658, April 1991.
Example Conference Paper:
[2]Gulistan Raja and M. J. Mirza, Performance comparison of advanced video codingH.264 standard with baseline H.263 and H.263+ standards, in Proc. 4th IEEEInternational Symposium on Communications & Information Technologies, ISCIT 04,
Sapporo, Japan, 2004, pp. 743746.
Example Book:
[3]Iain E.G. Richardson, Video Codec Design, Great Britain, John Wiley & Sons, 2003,ISBN: xx-yyyy-zzzz.
Example Web Link:[4] MPEG Software Simulation Group, The MSSG homepage, available on-line at
http://www.mpeg.org/MPEG/ MSSG, 2004.
Example Standard:
[5]ITU-T Video Coding for low bit rate communication, ITU-T Recommendation H.263;version 1, Nov 1995; version 2, Jan. 1998; version 3, Nov. 2000.
http://www.mpeg.org/MPEG/%20%20MSSGhttp://www.mpeg.org/MPEG/%20%20MSSGhttp://www.mpeg.org/MPEG/%20%20MSSG -
7/28/2019 Guidlines BSc Elect Engg Final Year Project Report Writing
18/18
9
Hard Copy Information
Page Size A4 (21 cm x 29. 7 cm)Page Margins Top and Bottom = 2.54 cm
Left 3.81 cm, and Right = 2.54 cm
Page orientation Portrait
Line Spacing Double
Page Numbering Bottom Left
Printing One Side per sheet
1. THREE Hard bound copies (1 for supervisor/group, 1 for library/group and 1 forstudent) of the project report are to be submitted for final project examination. Hard
bound means permanently stitched and bound in BLUE COVERwith the title of the
project and your name clearly inscribed on the cover as per format given at the first
page of template in SILVERcolor.
2. The SPINE of project report should have Authors 1st Name (in case of multipleauthors) / Authors Full Name (in case of single author) , B.Sc. Elect. Engg. and
Year of Passing ONLY. The Authors name should be in vertical orientation while
B.Sc. Elect. Engg. and year of passing. should be in horizontal orientation in the spine
of hard bound copy of project.
3. TWO CDs containing soft copy of project report (in PDF and MS WORD format) to besubmitted in the Academic Cell. Both CDs must be titled using Permanent Marker with
the Students Regd. Nos & Project Title in brief. The transparent plastic casings of CDs
must also be titled with Student Regd. Nos, Project Title, Supervisor Name & Signature.