GS2200M SKB 1 Quick Start Guide 2 · For iOS devices go to “App Store”, under the “Search”...

1VV0301422, Rev 1.1

Copyright © 2016 Telit. All rights reserved.

GS2200M SKBQuick Start GuideSupports GS2200Mxx Modules

This Quick Start Guide will walk you through the steps tosetup the SKB and run S2W or TLS application onGS2200M SKB

You will need the following items:

• Quick Start Guide (this document)• GS2200 Starter Kit Board• Serial Cable (USB to Mini-USB)• Tera Term VT Utility installed in the PC• Android 4.0+ based devices (phones, tablet) or iOS Device

(iOS 6+) with “Gainspan TLS” Application

1 Build the Package

2 Program the GS Module

Step 1 Login at https://wifi.telit.com/secure/login, and under SDK Builder tab, select the following: • Build Type - New Build • GainSpan Module - GS2200MIZ or later• Firmware version - GEPS v5.x.x • Build Output - Custom Package • Application - TLS AEK• Platform - SKB

Step 2 Click the Build button to generate the TLS binaries. The build configuration will be submitted and a confirmation email will be sent notifying that the TLS AEK package is complete and ready to download.

Download and unzip file containing the firmware and binaries used to program the board to local folder.

Step 1 Ensure the Power Measurement Switch is in the “ACTIVE” Position. Plug the mini-USB cable, one end of the USB port to GS2200 SKB USB and the other end of the USB port to the computer or laptop.

Step 3 While holding down the PROGRAM and RESTORE buttons, press and release the RESET button to put the GS2200 SKB into flash programming mode.

Step4 Open the GainSpan Serial Flash Programmer GUI application from "\Tools\GS_programming_tool" and select the Super Block and Firmware located at “\Embedded”. Click on “”Erase and Program” button.

Step 2 Switch power switch to the ‘ON’ position and check if the power LED is turned ON

Note: GS2200MIE has UFL connector for External Antenna.

Serial to Wi-Fi (S2W) – GS2200M module is used to interface a host micro-controller to a Wi-Fi network using AT commands, SKB comes pre-loaded with this application.

Temperature and Light Sensor (TLS) – For an application firm-ware that runs on the module (host-less), the TLS applicationdemonstrates how the GS2200M module can provide both appli-cation processor and Wi-Fi network connectivity functions for a connected device.

1VV0301422, Rev 1.1


3 Install TLS Application on Smart DeviceFor iOS devices go to “App Store”, under the “Search” option type “gainspan TLS”.

For andriod devices go to “Play Store”, under the “Search” option type “gainspan TLS”.

4 Run the GS ModuleStep 1 Open the Tera Term (or any Serial terminal) and configure the serial port for 115200 8N1.

Step 2 Power Cycle or press RESET to enter RUN mode. The terminal will show debug messages with information about SSID and IP address.

Step 3 The LED(D2) will be lit AMBER, indicating the SKB is run-ning TLS with SSID “GS_PROV_TLS-last 6 digits of MAC Address”.

5 Launch and Run TLS Application on iOS Smart Device

Step 1Enable Wi-Fi on the Smart Phone device and connect the device to TLS Limited AP with SSID GS2K_PROV_TLS-<last 6 digits of MAC Address> created by the GS2200 SKB.

Step 2 Enter the Passphrase “GS_<last 6 digits of MAC Address>”. Once connected, launch and run the TLS

application.

Step 3Smart phone detects mDNS service and displays the local TLS service “GS_PROV_TLS-<last 6 dig-its of MAC Address>_TLS”

1VV0301422, Rev 1.1


7 Launch and Run the TLS Application on Android Smart DeviceStep 1Enable Wi-Fi on the Smart Phone device and connect the device to TLS Limited AP with SSID GS2K_PROV_TLS-<last 6 digits of MAC Address> created by the GS2200 SKB.

Step 2 Tap on the SSID “GS_PROV_TLS_<last 6 digits of MAC Address>”, and Enter the Passphrase “GS_<last 6 digits of MAC Address>”

Step 3 Once connected, launch and Run TLS Application.

Step 4 Smart phone detects mDNS service and display the local TLS service “GS_PROV_TLS-<last 6 digits of MAC Address>_TLS”

Step 4“TAP” on the available service on the device. Below screen will be displayed

Step 5 “TAP” on the service on the device. Below screen will be displayed.

1VV0301422, Rev 1.1


Step 2 Enter the Passphrase “GS_<last 6 digits of MAC Address>”

Step 3 Open the web browser on laptop/tab and enter the URL http:192.168.240.1/tls.html, GainSpan TLS Web Application is displayed with the information for Light (Lux), Temperature, and RSSI information

8 Launch and Run the TLS Application on Web Browser

Step 1 Enable WiFi on the Laptop and connect it to TLS Lim-ited AP with SSID GS2K_PROV_TLS-<last 6 digits of MAC Address> created by the GS2200 SKB.

1VV0301422, Rev 1.1


For information, please refer to the following documents:

• GS2K SDK Builder User Guide- Configuring and generating custom S2W firmware binary

images from web portal based on features required

• GS2K Module Programming User Guide- How to Program the module

• GS2K SDK Application Programming Guide - If SDK is purchased, for setting up, compiling, and debugging

firmware using IAR IDE. This also has reference codes for var-ious use cases, debugging mechanisms, detailed description of various modules and features and much more

• GS2K S2W Use Case Reference Guide - For sequence of AT commands to be used for any particular

use case

• S2W Adapter Command Reference Guide - For detailed description of every AT command

• GS2K Live Calibration Application Note- For calibrating the module for optimum reception, which needs

to be done once in the lifetime of the product unless the flash is erased completely for some reason

- • GS2K Module Starter Kit Board Hardware User Guide

- For evaluation board description and hardware setup, jumper settings, component description, board specifications, and pin outs

Technical and Product SupportFor any clarification, technical and product support, pleaseemail to Telit Technical Support at:[email protected]

We recommend adding “Wi-fi” in subject of the email. For exam-ple, the subject of email can be “Wi-Fi: Association failing”, “Wi-Fi: SPI Driver Issue”.Also, in description of your email, please provide details aboutthe issue, product, module and use case including software firm-ware version, module version and type, application being used,customizations done to application, use case and issue fre-quency and ability to recreate it.

Information

• GS2K Memory Map and File System Application Note- Provides the memory architecture of the Wi-Fi modules and provide

details about types of memory, location, and content of various items in these memory locations

For further information, please visit the website link:https://www.telit.com/products/wifi-and-bluetooth/#wifi

[email protected]

GS2200M SKB 1 Quick Start Guide 2 · For iOS devices go to “App Store”, under the “Search”...

Documents

Transcript of GS2200M SKB 1 Quick Start Guide 2 · For iOS devices go to “App Store”, under the “Search”...