GRUBER HERMANOS, S. A. · GRUBER HERMANOS, S. A. Workshops and Offices located in::...
3
Page 1 GRUBER HERMANOS, S. A. Workshops and Offices located in:: Zumalacárregui, 30 - 48 903 Barakaldo - Vizcaya - SPAIN Teléfono +34 94 499 13 00 Fax: +34 94 499 10 90 [email protected] www.gruberhermanos.com Hammer mills are suitable for medium hard products grinding processes which would not be very abrasive in which a grain size output exceeding 1 mm is required. These equipments can be used as mills or ginders by adapting appropriately sized grids. The crusher - breakers are equipments indicated in the process of grinding of soft and slightly strong materials. They are also used in pre-grinding process to reduce energy costs of the mills. MS micronizing mills are suitable for the milling of soft or semi-hard products to sizes below 500μm, with a d 50 stable throughout the useful life of the machinery. DUPLEX mills are suitable for materials reduction processes to grain sizes over 500μm producing low amount of fines .. Fabrication Program Programa-3 en Milling and crushing Programa-3 en V.03.04
Transcript of GRUBER HERMANOS, S. A. · GRUBER HERMANOS, S. A. Workshops and Offices located in::...
Page 1
GRUBER HERMANOS, S. A.Workshops and Offices located in::Zumalacárregui, 30 - 48 903 Barakaldo - Vizcaya - SPAINTeléfono +34 94 499 13 00Fax: +34 94 499 10 [email protected]
Hammer mills are suitable for medium hard
products grinding processes which would not be very abrasive in which a grain size output exceeding 1 mm is required. These equipmentscan be used as mills or ginders by adaptingappropriately sized grids.
The crusher - breakers are equipments indicated in theprocess of grinding of soft and slightly strong materials.
They are also used in pre-grinding process to reduce energy costs of the mills.
MS micronizing mills are suitable for themilling of soft or semi-hard products to sizesbelow 500μm, with a d50 stable throughoutthe useful life of the machinery.
DUPLEX mills are suitable for materials reductionprocesses to grain sizes over 500μm producing low
amount of fines ..
Fabrication ProgramPrograma-3 en
Millin
ga
nd
crus
hin
g
Programa-3 enV.03.04
Page 2
GRUBER HERMANOS, S. A.Workshops and Offices located in::Zumalacárregui, 30 - 48 903 Barakaldo - Vizcaya - SPAINTeléfono +34 94 499 13 00Fax: +34 94 499 10 [email protected]
Fabrication ProgramPrograma-3 en
Programa-3 enV.03.04
Biconic mixers are suitable for homogenization processesof granulated and solids products that seek an intimate
mixing and ease-cleaning processes .
Spiral mixers are most commonly usedequipments in those mixing processes both solid, pasty, semi-liquid, powder and granules productsin which it seeks homogeneous mixing withoutcausing breakage of the particles of the mix elements.
High turbulence mixers are suitable forproducing fast mixing processes with all types
of dry powders, granules and pastes of lowdensity is seeks in a perfect mix using short periods of time without causing breakage of
particles
Mixin
g
The kneaders are the equipment used in mixing and/or kneading of wet or pastyproducts, in which obtain a homogeneousmass is needed
Page 3
GRUBER HERMANOS, S. A.Workshops and Offices located in::Zumalacárregui, 30 - 48 903 Barakaldo - Vizcaya - SPAINTeléfono +34 94 499 13 00Fax: +34 94 499 10 [email protected]
Clasificatio
nan
dd
ossificatio
n
The measuring vanes are used as a system of closureand extraction of granular or powdery products,
avoiding scapes or air entries in pressure circuits. Theyare also used as volumetric measurings for feeding
machines.
Fabrication ProgramPrograma-3 en
Programa-3 enV.03.04
The high efficiency cyclone equipments are themost commonly used equipments in dust separationprocesses or materials in suspension in an airstream.
Typical applications are:
avoid Environmental pollution,
pneumatic transports,
dust collection circuits,
exit of smoke with high concentrations ofproduct in suspension
air classifications equipments,
recovery of fly ash,,
industrial ventilation,
and usually placed in the pre-filteringstage.
Classification facilities are the most efficientsystem in which the separation of a very
specific particle size, starting from a set ofdifferent sizes is required.
The maximum particle size can be easilyobtained by acting on the classifier cage speed,
achieving a very precise cutting.
