Graphic Science (MEL110) (2-0-4) Dr. Ashish K Darpe, Department of Mechanical Engineering...

Graphic Science (MEL110) (2-0-4) Dr. Ashish K Darpe, Department of Mechanical Engineering III-176 #6095(O), #1618(R) Course for Part 1: Introduction, general instructions for lettering, instruments, etc. Projection Systems- perspective, orthographic, isometric & oblique, Dimensioning Practicals for Part 1 – sketching on tracing sheets. Tracing sheet pad, one graph paper, H&HB pencils, eraser,

Upload
martha-ward
Category

Documents
view
213
download
0

Embed Size (px):

Transcript of Graphic Science (MEL110) (2-0-4) Dr. Ashish K Darpe, Department of Mechanical Engineering...

Graphic Science (MEL110) (2-0-4)

Dr. Ashish K Darpe,

Department of Mechanical Engineering

III-176 #6095(O), #1618(R)

Course for Part 1:

Introduction, general instructions for lettering, instruments, etc.

Projection Systems- perspective, orthographic, isometric & oblique,

Dimensioning

Practicals for Part 1 – sketching on tracing sheets.

Tracing sheet pad, one graph paper, H&HB pencils, eraser,

scale, compass & divider, zero grade sand paper.

Page 2: Graphic Science (MEL110) (2-0-4) Dr. Ashish K Darpe, Department of Mechanical Engineering III-176#6095(O), #1618(R) Course for Part 1: Introduction, general.

Evaluation based on Practical work: 40% Minor Tests:15% each Major Test: 30% Text Book:Fundamentals of Engineering Drawing Luzadder & Duff(9th or 11th Edition) Prentice-Hall of India Additional Reference Book: Engineering Drawing, N D Bhatt

Some practicals on computer in Computer Aided Graphics Instruction Laboratory (CAGIL) Room No. III-331-332

Page 3: Graphic Science (MEL110) (2-0-4) Dr. Ashish K Darpe, Department of Mechanical Engineering III-176#6095(O), #1618(R) Course for Part 1: Introduction, general.

COURSE OVERVIEW

Lettering

ProjectionsOrthographic Axonometric Isometric Oblique

Plane geometric constructions

Auxiliary Planes

Intersection of surfaces

Development of surfaces

Projection of planes and solids

Sectioning and Dimensioning

Computer Aided Drawing

Page 4: Graphic Science (MEL110) (2-0-4) Dr. Ashish K Darpe, Department of Mechanical Engineering III-176#6095(O), #1618(R) Course for Part 1: Introduction, general.

ORTHOGRAPHIC PROJECTIONS

ISOMETRIC PROJECTIONS

Page 5: Graphic Science (MEL110) (2-0-4) Dr. Ashish K Darpe, Department of Mechanical Engineering III-176#6095(O), #1618(R) Course for Part 1: Introduction, general.

AUXILIARY VIEWS

Page 6: Graphic Science (MEL110) (2-0-4) Dr. Ashish K Darpe, Department of Mechanical Engineering III-176#6095(O), #1618(R) Course for Part 1: Introduction, general.

ENGINEERING CURVES

Page 7: Graphic Science (MEL110) (2-0-4) Dr. Ashish K Darpe, Department of Mechanical Engineering III-176#6095(O), #1618(R) Course for Part 1: Introduction, general.

DEVELOPMENT OF SURFACES

Page 8: Graphic Science (MEL110) (2-0-4) Dr. Ashish K Darpe, Department of Mechanical Engineering III-176#6095(O), #1618(R) Course for Part 1: Introduction, general.

SECTION OF SOLIDS

Page 9: Graphic Science (MEL110) (2-0-4) Dr. Ashish K Darpe, Department of Mechanical Engineering III-176#6095(O), #1618(R) Course for Part 1: Introduction, general.

INTERPENETRATION OF SURFACES

Orthographic projections Dr Ashish K Darpe Department of Mechanical Engineering IIT Delhi.

Douglas County Candidate Guide · 12/30/2019 · Douglas County Clerk-Treasurer Election’s Office election@douglasnv.us (775)783-6095 Govotedouglas.com Offices, within Douglas

Douglas County Candidate Guide · 12/30/2019 · Douglas County Clerk-Treasurer Election’s Office [email protected] (775)783-6095 Govotedouglas.com Offices, within Douglas

Remaining lectures Last lecture by Dr. Darpe: Wed, 3 rd Oct Lectures by Prof S R Kale 22 st Oct (Mon) 24 th Oct (Wed) and 31 st Oct (Wed) 11am – 11:55am.

$Research Article Finite Element Multibody Simulation of a ...ey used the fracture mechanics and obtained a full 6×6 exibility matrix for a transverse open surface crack on sha . Darpe$