Grandio Ascent EXTENSION KIT Manual April 14 2016

G R E E N H O U S E S GRANDIO

®

GREENHOUSE USER MANUAL© 2013 Grandio Greenhouses, Backyard Living Source Inc. All rights reserved

April 14, 2016 Extendable Models

GRANDIO ASCENT 8x12, 8x16, 8x20, 8x24 KIT MANUALINCLUDES INSTRUCTIONS FOR BACK DOOR TRANSFORMATION

Grandio Ascent 8x24 Shown In Image STOPThis manual is for

8x12, 8x16, 8x20 & 8x24.

If building an 8x8 with no extensions refer to

that manual.


®

Before you begin, take time to complete this check list.

Take inventory of all parts using the parts list at the back of this manual on pages 66-75. The base kit parts list is at the front on page 12 and 13. The back door transformation kit parts list is on page 76.

Be cautious where you place the polycarbonate panels as they will burn grass or plants if left on top of them in direct sunlight. Note that clear film side of panels should always face the sun and white film side faces inside green-house. Panels may scratch easily so be careful what you clean them with.

Plan out when and where you are going to place the greenhouse, we recom-mend that you place it in an area that will receive direct sunlight and will be protected from the wind as much as possible

It will take at least (2) people to put the greenhouse together.

Before your build, make sure you are allowed to build it! Consult all building codes, as well as City or Municipality ordinances and HOA’s, as you may need a permit or documentation before you build.

Contact your insurance company to make sure your Grandio Greenhouse will be covered on your policy.

Call your local utilities companies before digging.

Do not attempt to begin construction on a windy day, plan to complete assembly in one day. Damage caused by incomplete assembly is not covered by warranty.

Your greenhouse should be built on a flat level surface allowing for drainage.

Read this entire manual to get familiar with all pieces and parts prior to beginning assembly. Follow the steps outlined in the order presented!

Save this owner’s manual for future reference and if you need our help.

CONTACT OUR CUSTOMER SERVICE DEPARTMENT at: 1-866-448-8231

Hours: 8:30a.m.-5:00p.m. Monday through Friday (Mountain Standard Time)

Backyard Living Source9543 W. Emerald St., Suite 101

Boise, ID 83704www.grandiogreenhouses.com

IMPORTANT! PLEASE READ BEFORE BEGINNING ASSEMBLY

Dear Valued Customer, We would like to congratulate you on your new Grandio Greenhouse purchase. We are confident that you have made the right decision in choos-ing Grandio. Our greenhouses are made with high quality aluminium and polycarbonate and will last for many garden seasons to come.

Please take the time to carefully read this instruction manual for an easier and more enjoyable assembly experience.

Cheers!Grandio Greenhouses

1

2

IMPORTANT! SAFETY INSTRUCTIONS

FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY.

To ensure safety, do not attempt to assemble this product without following the instructions carefully. Check entire box and inside all packing material for parts and/or additional instruction materials. Before beginning assembly, read the instruc-tions and identify all parts using the hardware identifier and parts list on pages 67-76. Complete assembly and proper usage are essential to reduce the risk of accident or injury when using your Grandio Greenhouse.

CAUTION: Do not leave polycarbonate panels laying on grass or leave in the sun or extreme heat, keep in a cool dry place until they are to be installed!! (May cause burning to plants or grass if left directly on top of them, also may damage panels due to the protective �lm adhering to panels.) Panels may scratch easily. Do Not use solvent cleaners.

• Each of the polycarbonate panels have a clear �lm side that should always face the sun, and a white �lm side which faces inside. The clear side has a UV coating and we recommend marking a small “x” on a corner of each panel to determine which side has the UV Coating as you cannot visually determine with your eye in the case of future disassembly.

• Due to shipping, the grooves of some of the aluminum profiles may be too small to insert into the polycarbonate sheet, you may carefully use a screwdriver to pry the framework open so the polycarbonate sheet can be inserted smoothly.

• Do not use or store hot objects such as grills, blow torches, welding equipment, etc. in or near your greenhouse.

• Do not allow children or pets to play in greenhouse or in the set up area until assembly is complete.

• If using a ladder during assembly, use extreme caution.

• A clean level surface is essential to maintaining the solid integrity of the structure, Install the base correctly as described in manual. Please anchor the greenhouse down to a �rm and level base. If not properly installed warranty may be void.

NEEDED FOR ASSEMBLY • Tape Measure • 2 Step Ladders • Safety Glasses• Level • Work Gloves • Drill • Carpenter Square • Permanent Marker • Silicone Caulk• At Least 2 Adults • Masking Tape • Folding Utility Table

GRANDIO

T I PWhen you see this icon

pay special attention to

the helpful tips we have provided that will

make installation more e�cient.


®

ASSEMBLY INSTRUCTION STEPS

PREPARE FOR ASSEMBLY

STEP ONE: BASE ASSEMBLY

STEP TWO: FRONT ASSEMBLY

STEP THREE: BACK ASSEMBLY

STEP FOUR: MIDDLE ASSEMBLY

STEP FIVE: EXTENSION ASSEMBLY

STEP SIX: INTERIOR SUPPORT ASSEMBLY

STEP SEVEN: DOOR ASSEMBLY

3

Introduction.............................................................................1Safety Instructions.................................................................2Prepare For Assembly...........................................................4 Box Con�gurations ...............................................................5Diagrams of Assembled Grandio Ascent Sizes 8x8, 8x12, 8x16, 8x20, 8x24.........................6-10 Base Kit Assembly Information.......................................11Base Kit Parts Lists........................................................12-138x12 Base Kit........................................................................148x16 Base Kit........................................................................158x20 Base Kit........................................................................168x24 Base Kit........................................................................17Base Kit Assembly and Installation........................18-20Front Assembly.............................................................21-26Back Assembly..............................................................27-31Middle Assembly.........................................................32-37Extension Assembly...................................................38-448x20 and 8x24 Extension Assembly.....................45-49Extension Assembly Continued.............................50-58Interior Roof Supports.....................................................59Door Assembly.............................................................60-65GRA-ASC-8A Parts List...............................................66-68GRA-ASC-8P Parts List......................................................69GRA-ASC-4X Parts List................................................70-72GRA-ASC-8XA Parts List.............................................73-74GRA-ASC-8XP Parts List....................................................75GRA-ASC-BD Parts List......................................................76Warranty.................................................................................77

93”2362 mm

72 1/16”1830 mm

42”1066 mm8X12

8X12

LEFT SIDE

FRONT WIDTH

RO

OF

PE

AK

HE

IGH

T

DO

OR

HE

IGH

T

DOOR

55 11/16”1414 mm

EA

VE

HE

IGH

T

PREPARE FOR GREENHOUSE ASSEMBLY

Before assembling your new greenhouse, a proper foundation must be prepared. A number of anchor-ing options are acceptable, based on wind and ground conditions in your area.

Pre-read pages 11-20 for base kit assembly informa-tion.

Go to www.grandiogreenhouses.com for founda-tion ideas and tour our online learning center for tips, tricks and videos for putting your greenhouse together.

4

8X12 GRANDIO ASCENT A-FRAME STYLE GREENHOUSE DIMENSIONS

*SEE BASE KIT ASSEMBLY SECTION FOR ALL GREENHOUSE BASE DIMENSIONS ON PAGES 14-17.

Transparent Clear Film

Opal White Film

Polycarbonate Panels

Sun

The UV-Protected side is covered with clear �lm and must face toward the sun. The side covered in white �lm will always face the interior of the greenhouse. We suggest you peel all �lm o� completely prior to assem-bly and use a permanent marker to place a small “X” on the lower right corner of each panel on the clear side that faces the sun, each panel has a sticker labeling the panel number and this side always faces the sun or outward as well. DO NOT REMOVE LABELS UNTIL YOU INSTALL PANELS. The “X” is suggested in case you dis-assemble your greenhouse in the future so you may identify which side has the UV coating. Always use gloves when handling the polycarbonate panels as the edges can be very sharp.

IMPORTANT: POLYCARBONATE PANELS

IMPORTANT: BASE KIT ASSEMBLY & GREENHOUSE PLACEMENT

143 3/4”3652 mm

97 7/16”2475 mm

BASE 3 1/4”82.6 mm

1 3/4” / 44.4mmGUTTERS

EXTENSION KIT BOX CONFIGURATIONS

GRA-ASC-8P

Ascent 8’x8’

GRA-ASC-8A

+

Aluminum Extrusions, Hardware Bag, Front,

Back and Doors.

8x8 Base Kit

GRA-BAS-8


Base kit & hardware

+

Ascent 8’x8’

GRA-ASC-8AAluminum Extrusions, Hardware Bag, Front,

Back and Doors.

GRA-ASC-8PPolycarbonate Panels

8x8 Base Kit

GRA-BAS-8Base kit & hardware

Ascent 8’ Extension

GRA-ASC-8XA

Aluminum Extrusions, Hardware Bag, 8’ Base

Extension, 2 Roof Vents, 2 Snow Load Extension Supports.

GRANDIO ASCENT 8X16

GRA-ASC-8XPPolycarbonate Panels For The 8’ Extension

+

Ascent 8’x8’


Back and Doors.


8x8 Base Kit



GRA-ASC-8XA



GRANDIO ASCENT 8X20



GRA-ASC-4XAluminum Extrusions, Hardware Bag, 4’ Base Extension, 1 Roof Vent, 2 Snow Load Extension Supports, Polycarbon-

ate Panels for 4’ Extension.

+ +

Ascent 8’x8’


Back and Doors.


8x8 Base Kit



GRA-ASC-8XA



GRANDIO ASCENT 8X24

GRA-ASC-8PPolycarbonate Panels For The 8’ Extension

+


GRA-ASC-8XA





GRA-ASC-4XAluminum Extrusions, Hardware Bag, 4’ Base Extension, 1 Roof Vent, 2 Snow Load Extension Supports, Polycarbon-

ate Panels for 4’ Extension.

Fron

t

Back

Fron

t

Back

Fron

t

Back

Fron

t

Back

5

We recommend that you lay all of your boxes out as shown below for an organized assembly. Locate your greenhouse size and situate near your assembly site. We suggest you lay the parts out on a tarp so you do not lose items in the grass or dirt near your building site.*See the reference diagrams on pages 6-10 for more information about how the parts will go together and what makes up each section for the assembly. If building a back door you will follow the instructions in the manual, the parts for the transformation are in box GRA-ASC-BD.

GRANDIO ASCENT 8X12

Y4-1L08B

LEFT SIDE RIGHT SIDE

609

601A-B

604-L 604-R

622-L 622-R

601A-FL

609 609

601A-FR

609

622 622

601A-B

FRONT

L08A

610

L08B-X

601B 601B

607603C603A

601B 601B

L08D L08D

620 620

623A623A

623B 623B

619

L21

LEFT SIDE

610

602B602A

602A

602A

602B

L08C

603B/616

602B

L08C-X

L08C-X

615

RIGHT SIDE

603B/616

602A

602A

L08C-X

602B

L08C

602B

610

602A

L08C-X

602B

615

6

602C

L08B-X

602D

L08A-X

610 610

618 618

Y5

Y4-2 Y2-1Y2-2

Y1Y1

Y2-1

Y1

Y3-1 Y3-2Y9 Y9

Y6

Y7

Outside View

606-WS

606-WS

606-WS

606-WS

BA-S1

L08A-X

606-WS606-WS

603B

Y6

Y6

Y6

Y7

Y7

Y7

Y7

Y7

Y8Y8

BA-S2 BA-S2

606-WS

606-WS

606-WS

606-WSY6

Y6

Y6

Y6

Y5 Y5

Y5 Y2-2

Y1

606-WS 606-WS 606-WS606-WSY1Y1

DIAGRAM SHOWS THE ASSEMBLED(8’x8’ BASIC CONFIGURATION)

(GRA-ASC-8A & GRA-ASC-8P & GRA-BAS-8) 8x8 ASCENT KIT INCLUDES, FRONT,

BACK, BASE AND SIDES.

BA-S1

602D

603B603B

603B

L28L28

615

609

610

602B

602A

602A

602A

602B

L08C

603B

/616

602B

L08C

-XL08M

-X

618

Y9

Y6

Y7

606-

WS

606-

WS

606-

WS

606-

WS

Y6Y6Y6

Y7 Y7Y8

BA-S

2

609

603B

/616

602A

602A

L08C

-X

602BL0

8C

602B

610 60

2A

L08M

-X

602B

615

618

Y9

Y7 Y7 Y7Y8

BA-S

2

606-

WS

606-

WS

606-

WS

606-

WS

Y6Y6Y6Y6

603B 60

4-L

604-

R

622-

L62

2-R

601A

-FL

601A

-FR

622

62260

3C60

3A60

1B60

1B

L08D

L08D

620

620

623A

623A

623B

623B

619

L21

L08A

-X

Y5Y2

-1

Y1

Y3-1

Y3-2

BA-S

1

L08A

-X

606-

WS

606-

WS

603B

Y5Y5

Y5Y2

-2 Y1603B

609

601A

-B

609

601A

-B

L08A

610

L08B

L08B

-XL0

8B-X

601B

601B

602C

602D

602D

610

610

Y4-2

Y4-1

Y2-1

Y2-2

Y1Y1

606-

WS

606-

WS

606-

WS

606-

WS

Y1Y1

BA-S

1

609

603B

/616

602A

602BL0

8C

602B

610

L08C

-X

615

618

Y9

Y7 Y8

BA-S

4

606-

WS

606-

WS

Y6Y6

609

610

602B

602A

602A

602B

L08C

L08C

-X

Y7

606-

WS

606-

WS

Y6Y6

Y7BA

-S2

607

607

(8’x8’ Original Kit) (GRA-ASC-8A & GRA-ASC-8P & GRA-BAS-8) 8x8 Ascent Includes Front, Back, Base, and Sides

8x8 Ascent Side

FRO

NT

In b

oxes

GR

A-A

SC-8

A a

nd G

RA

-ASC

-8P,

th

e b

ase

for

8x8

is a

ll in

GR

A-B

AS

-8.

LEF

T S

IDE

In b

oxes

GR

A-A

SC-8

A a

nd G

RA

-ASC

-8P,

th

e b

ase

for

8x8

is a

ll in

GR

A-B

AS

-8.

RIG

HT

SID

EIn

box

es G

RA

-ASC

-8A

and

GR

A-A

SC-8

P,

the

bas

e fo

r 8x

8 is

all

in G

RA

-BA

S-8

.

BA

CK

In b

oxes

GR

A-A

SC-8

A a

nd G

RA

-ASC

-8P,

th

e b

ase

for

8x8

is a

ll in

GR

A-B

AS

-8.

(4’ Extensions Side) 4X Ascent Side(4’ Extension Side) (GRA-ASC-4X)

Ascent 4’ Side Extension Includes Base

Outside View

DIAGRAM SHOWS THE ASSEMBLED 8X12 GRANDIO ASCENT

THE BOX CONFIGURATION IS AN ASCENT 8X8 PLUS A 4 FOOT EXTENSION KIT

7

603B

603B

615

609

603B

/616

602A

602A

L08C

-X

602BL0

8C

602B

610 60

2A

L08M

-X

602B

615

618

Y9

Y7 Y7 Y7Y8

BA-S

2

606-

WS

606-

WS

606-

WS

606-

WS

Y6Y6Y6Y6

604-

L60

4-R

622-

L62

2-R

601A

-FL

601A

-FR

622

62260

3C60

3A60

1B60

1B

L08D

L08D

620

620

623A

623A

623B

623B

619

L21

L08A

-X

Y5Y2

-1

Y1

Y3-1

Y3-2

BA-S

1

L08A

-X

606-

WS

606-

WS

603B

Y5Y5

Y5Y2

-2 Y1603B601A

-B

L08A

L08B

-XL0

8B-X

601B

601B

603B

603B

L08B

602C

602D

602D

610

Y4-2

Y4-1

Y2-1

Y2-2

Y1Y1

606-

WS

606-

WS

606-

WS

606-

WS

Y1Y1

BA-S

1

601A

-B

617

617

609

603B

/616

602A

602A

602BL0

8C

602B

610 60

2A

L08C

-X

602B

615

618

Y9

Y7 Y7 Y7Y8

BA-S

2

606-

WS

606-

WS

606-

WS

606-

WS

Y6Y6Y6Y6

609

610

602B

602A

602A

602A

602B

L08C

603B

/616

602B

L08C

-XL08M

-X

618

Y9

Y6

Y7

606-

WS

606-

WS

606-

WS

606-

WS

Y6Y6Y6

Y7 Y7Y8

BA-S

2

609

610

602B

602A

602A

602A

602B

L08C

603B

/616

602B

L08C

-X

618

Y9

Y6

Y7

606-

WS

606-

WS

606-

WS

606-

WS

Y6Y6Y6

Y7 Y7Y8

BA-S

2

615

609

61060

9

Outside View


THE BOX CONFIGURATION IS AN ASCENT 8X8 PLUS AN 8 FOOT EXTENSION KIT


(8’ Extension Side) (GRA-ASC-8XA & GRA-ASC-8XP) Ascent 8’ Side Extension includes Base

8x8 Ascent Side(8’ Extension Side) 8X Ascent Side

FRO

NT

In b

oxes

GR

A-A

SC-8

A a

nd G

RA

-ASC

-8P,

th

e b

ase

for

8x8

is a

ll in

GR

A-B

AS

-8.

LEF

T S

IDE

In b

oxes

GR

A-A

SC-8

A a

nd G

RA

-ASC

-8P,

th

e b

ase

for

8x8

is a

ll in

GR

A-B

AS

-8.

RIG

HT

SID

EIn

box

es G

RA

-ASC

-8A

and

GR

A-A

SC-8

P,

the

bas

e fo

r 8x

8 is

all

in G

RA

-BA

S-8

.

BA

CK

In b

oxes

GR

A-A

SC-8

A a

nd G

RA

-ASC

-8P,

th

e b

ase

for

8x8

is a

ll in

GR

A-B

AS

-8.

8

609

603B

/616

602A

602A

L08C

-X

602BL0

8C

602B

610

602A

602B

615

618

Y9

Y7 Y7 Y7Y8

BA-S

2

606-

WS

606-

WS

606-

WS

606-

WS

Y6Y6Y6Y6

604-

L60

4-R

622-

L62

2-R

601A

-FL

601A

-FR

622

62260

3C60

3A60

1B60

1B

L08D

L08D

620

620

623A

623A

623B

623B

619

L21

Y5Y2

-1

Y1

Y3-1

Y3-2

BA-S

1

L08A

-X60

6-W

S60

6-W

S

603B

Y5Y5

Y5Y2

-2 Y1

607

607

609

603B

/616

602A

602A

L08M

-X

602BL0

8C

602B

610 60

2A

L08M

-X

602B

615

618

Y9

Y7 Y7 Y7Y8

BA-S

2

606-

WS

606-

WS

606-

WS

606-

WS

Y6Y6Y6Y6

615

609

610

602B

602A

602A

602A

602B

L08C

603B

/616

602B

L08C

-XL08M

-X

618

Y9

Y6

Y7

606-

WS

606-

WS

606-

WS

606-

WS

Y6Y6Y6

Y7 Y7Y8

BA-S

2

609

610

602B

602A

602A

602A

602B

L08C

603B

/616

602B

L08M

-X

618

Y9

Y6

Y7

606-

WS

606-

WS

606-

WS

606-

WS

Y6Y6Y6

Y7 Y7Y8

BA-S

2

615

L08A

-X

603B601A

-B

L08A

L08B

-XL0

8B-X

L08B

602C

602D

602D

610

Y4-2

Y4-1

Y2-1

Y2-2

Y1Y1

606-

WS

606-

WS

606-

WS

606-

WS

Y1Y1

BA-S

1

601A

-B

609

61060

9

603B

603B

609

610

602B

602A

602A

602B

L08C

L08C

-X

Y7

606-

WS

606-

WS

Y6Y6

Y7BA

-S2

609

603B

/616

602A

602BL0

8C

602B

610

L08C

-X

615

618

Y9

Y7 Y8

BA-S

4

606-

WS

606-

WS

Y6Y6

602A

607

AZ1

AZ1



AZ1

AZ1

(4’ Extensions Side) 4X Ascent Side

(4’ Extension Side) (GRA-ASC-4X)Ascent 4’ Side Extension

Includes Base8x8 Ascent Side

(8’ Extension Side) 8X Ascent Side

Outside View


THE BOX CONFIGURATION IS AN ELITE 8X8 PLUS AN 8 FOOT AND A 4 FOOT EXTENSION KIT

BA

CK

In b

oxes

GR

A-A

SC-8

A a

nd G

RA

-ASC

-8P,

th

e b

ase

for

8x8

is a

ll in

GR

A-B

AS

-8.

FRO

NT

In b

oxes

GR

A-A

SC-8

A a

nd G

RA

-ASC

-8P,

th

e b

ase

for

8x8

is a

ll in

GR

A-B

AS

-8.

LEF

T S

IDE

In b

oxes

GR

A-A

SC-8

A a

nd G

RA

-ASC

-8P,

th

e b

ase

for

8x8

is a

ll in

GR

A-B

AS

-8.

RIG

HT

SID

EIn

box

es G

RA

-ASC

-8A

and

GR

A-A

SC-8

P,

the

bas

e fo

r 8x

8 is

all

in G

RA

-BA

S-8

.

9

609

RIG

HT

SID

E

603B

/616

602A

602A

L08C

-X

602BL0

8C

602B

610

602A

602B

615

618

Y9

Y7 Y7 Y7Y8

BA-S

2

606-

WS

606-

WS

606-

WS

606-

WS

Y6Y6Y6Y6

604-

L60

4-R

622-

L62

2-R

601A

-FL

601A

-FR

622

622

FRO

NT

603C

603A

601B

601B

L08D

L08D

620

620

623A

623A

623B

623B

L21

Y5Y2

-1

Y1

Y3-1

Y3-2 L0

8A-X

606-

WS

606-

WS

603B

Y5Y5

Y5Y2

-2 Y1

607

607

609

603B

/616

602A

602A

L08C

-X

602BL0

8C

602B

610 60

2A60

2B

615

618

Y9

Y7 Y7 Y7Y8

BA-S

2

606-

WS

606-

WS

606-

WS

606-

WS

Y6Y6Y6Y6

602A

602B

615

609

LEF

T S

IDE

610

602B

602A

602A

602A

602B

L08C

603B

/616

602B

L08C

-X

618

Y9

Y6

Y7

606-

WS

606-

WS

606-

WS

606-

WS

Y6Y6Y6

Y7 Y7Y8

BA-S

2

609

610

602B

602A

602A

602A

602B

L08C

603B

/616

602B

618

Y9

Y6

Y7

606-

WS

606-

WS

606-

WS

606-

WS

Y6Y6Y6

Y7 Y7Y8

BA-S

2

615

L08A

-X

603B601A

-B

BA

CK

L08A

L08B

-XL0

8B-X

L08B

602C

602D

602D

610

Y4-2

Y4-1

Y2-1

Y2-2

Y1Y1

606-

WS

606-

WS

606-

WS

606-

WS

Y1Y1

BA-S

1

601A

-B

609

61060

9

603B

603B

609

610

602B

602A

602A

602A

602B

L08C

603B

/616

602B

L08M

-x

618

Y9

Y6

Y7

606-

WS

606-

WS

606-

WS

606-

WS

Y6Y6Y6

Y7 Y7Y8

BA-S

2

615

607


THE BOX CONFIGURATION IS AN ASCENT 8X8 PLUS (2) 8 FOOT EXTENSION KITS

8x8 Ascent Side(8’ Extension Side) 8X Ascent Side(8’ Extension Side) 8X Ascent Side(8’x8’ Original Kit) (GRA-ASC-8A & GRA-ASC-8P & GRA-BAS-8)

8x8 Ascent Includes Front, Back, Base, and Sides



AZ1

602A

L08M

-X

609

603B

/616

602A

602A

L08M

-X

602BL0

8C

602B

610 60

2A60

2B

615

618

Y9

Y7 Y7 Y7Y8

BA-S

2

606-

WS

606-

WS

606-

WS

606-

WS

Y6Y6Y6Y6

602B

AZ1

619

BA-S

1

Outside View

10

L08C

-XL0

8C-X

Introduction.............................................................................1Safety Instructions.................................................................2Prepare For Assembly...........................................................4 Box Con�gurations ...............................................................5Diagrams of Assembled Grandio Ascent Sizes 8x8, 8x12, 8x16, 8x20, 8x24.........................6-10 Base Kit Assembly Information.......................................11Base Kit Parts Lists........................................................12-138x12 Base Kit........................................................................148x16 Base Kit........................................................................158x20 Base Kit........................................................................168x24 Base Kit........................................................................17Base Kit Assembly and Installation........................18-20Front Assembly.............................................................21-26Back Assembly..............................................................27-31Middle Assembly.........................................................32-37Extension Assembly...................................................38-448x20 and 8x24 Extension Assembly.....................45-49Extension Assembly Continued.............................50-58Interior Roof Supports.....................................................59Door Assembly.............................................................60-65GRA-ASC-8A Parts List...............................................66-68GRA-ASC-8P Parts List......................................................69GRA-ASC-4X Parts List................................................70-72GRA-ASC-8XA Parts List.............................................73-74GRA-ASC-8XP Parts List....................................................75GRA-ASC-BD Parts List......................................................76Warranty.................................................................................77

11

BASE KIT ASSEMBLY INSTRUCTIONSPre-Plan The Placement Of Your Structure Allow enough room to get a wheel barrow in and around your structure.

Be sure the orientation will allow for proper drainage in and around your greenhouse.

It is recommended that you place your greenhouse in an area of your property that receives the most sunlight but is also somewhat protected by trees, fencing or your home for wind protection and also to keep the temperature up during early spring and late fall.

The best placement depends on the features of your property, it is suggested in most scenarios to have your greenhouse face South on its broadest side and to have the door face East or West depending on typical wind directions in your area. Do not worry if your orientation will not allow for the placement to be as suggested, as a greenhouse that is facing North is better than no greenhouse at all.

Avoid building your greenhouse at the base of a slope as these are often frost pockets where cold air collects, this will not be good for your greenhouse in keeping the temperature up inside.

Extreme Wind Conditions: If you live in a windy location there is no way to build a 100% storm safe greenhouse, but there are a number of things you can do to minimize the chance of damage. Ensure that the base is level and square, be sure all panels are tightly in place and that all aluminum extrusions are tight. The main problem is usually that wind gets into the greenhouse and the pressure pushes a panel out and then the force of the wind on the interior causes more damage. It is best if you are expecting an extreme weather event that you disable any auto roof vents and make sure all doors and windows are closed and locked shut. Also you may need to build a wind break for extreme condi-tion areas where wind is constant and extreme.

See our website GrandioGreenhouses.com for Extreme Weather Anchoring Kits and Moisture Control Kits to aid in protecting your green-house in the event of harsh weather conditions prior to beginning assembly.

It is ideal for your greenhouse to have water, electricity and even gas plumbed into place before construction. This will make watering plants and keeping the temperature and air circulation to the max e�ciency.

You will need to choose an anchoring system prior to installation, see our website for options: www.GrandioGreenhouses.com

For Cement Base Installation: We recommend you use wedge style concrete anchoring bolts to secure your structure.

For Deck Base Installation: We recommend you use anchoring bolts to secure your structure.

For Earth Installation: We recommend you use the BA-A1 / L-BOLT anchoring system, and bury corner posts into the ground and seal into place with quickrete..

BA-S5

BA-S6

BA-C4

BA-S10

BA-S03

ML01

46 3/4 in / 1187 mm

46 3/4 in / 1187 mm

8 7/16 in / 214 mm

1/2 x 3/4

M6*14

NUT

GRAPHIC PART NAME SIZE/LOCATION QUANTITY

1

1

2

2

16

16

BA-S1

BA-S2

BA-C3

BA-S03

ML01

W05

97 3/8 in / 2474 mm

94/4 in / 2394 mm

5 7/16 in 138 mm

M6*14

NUT

CLIPS

PARTS WILL BE FOUND IN (GRA-BAS-8) BOXTHAT MAKE UP THE 8’X8’ BASE KIT


2

2

4

28

28

9

BASE KIT PARTS LIST

12

PAR

TS

LIST

FO

R B

ASE

KIT

PARTS WILL BE FOUND IN (GRA-ASC-4X) BOXFOR THE 4’ BASE KIT EXTENSION

BA-S3

BA-S4

BA-C4

BA-S10

BA-S03

ML01

93 7/16 in / 2374 mm

93 7/16 in / 2374 mm

8 7/16 in /214 mm

1/2 X 3/4

M6*14

NUT

PARTS WILL BE FOUND IN (GRA-ASC-8XA) BOXFOR THE 8’ BASE KIT EXTENSION


1

1

2

2

16

16

BASE KIT PARTS LIST

13

PAR

TS LIST

FOR

BA

SE K

IT

BA-S2

BA-S2

BA-C3

BA-C3

BA-C3

1.1 Layout all base kit pieces to prepare for assembly. Note that one BA-S1 will be at the front and one BA-S1 will be at the back and the BA-S2’s will be on the sides attaching to the front BA-S1. The BA-S5 and BA-S6 will attach to the back BA-S1, See diagram . 1.2 Attach the BA-S2 to the BA-S5 with the BA-C4 using the BA-S03 and ML01. See . Repeat for other side connecting the BA-S6 and the BA-S2. Go to page 18 for the next step.

BA-S5BA-S6

BA-C3

8x12 BASE KIT ASSEMBLY INSTRUCTIONS(GRA-BAS-8) AND (GRA-ASC-4X)

BA-C4

BA-C4

GRANDIO

T I PNote that the holes for screws on the base kit

sides have about a 2 foot gap between each, so be sure base kit extensions are assembled properly. See .

BA-C4

BA-S5 BA-S2

BA-S03ML01

14

STE

P O

NE

BA-S10

BA-S10143 3/4” / 3652 mm

97 7/16” / 2475 mm

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

BA-S1

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

BA-S1

HOLE FOR ANCHOR

BA-S2

BA-S2

BA-C3

BA-C3

BA-C4

BA-S3BA-S4

BA-C3

BA-C4

1.3 Layout all base kit pieces to prepare for assembly. Note that one BA-S1 will be at the front and one BA-S1 will be at the back and the BA-S2’s will be on the sides attaching to the front BA-S1. The BA-S3 and BA-S4 will attach to the back BA-S1 See diagram . 1.4 Attach the BA-S2 to the BA-S3 with the BA-C4 using the BA-S03 and ML01. See . Repeat for other side connecting the BA-S4 and the BA-S2. Go to page 18 for the next step.

8x16 BASE KIT ASSEMBLY INSTRUCTIONS(GRA-BAS-8) AND (GRA-ASC-8XA)

BA-C3

15

STE

P O

NE

BA-C4

BA-S3 BA-S2

BA-S03ML01

BA-S10

BA-S10

GRANDIO



190 15/16” / 4849 mm

97 7/16” /

2475 mm

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

BA-S1

HOLE FOR ANCHOR

HOLE FOR ANCHOR

BA-S1

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

BA-S2BA-S2

BA-C3

BA-C3

BA-S3BA-S4

BA-C3

BA-C4

BA-C3

BA-C4

BA-S5

BA-S6

1.5 Layout all base kit pieces to prepare for assembly. Note that one BA-S1 will be at the front and one BA-S1 will be at the back and the BA-S2’s will be on the sides attaching to the front BA-S1. The BA-S5 and BA-S6 will attach to the back BA-S1, See diagram . 1.6 Attach the BA-S2 to the BA-S3 with the BA-C4 using the BA-S03 and ML01. See . Repeat for other side connecting the BA-S4 and the BA-S2, then BA-S3 to BA-S5 and BA-S4 to BA-S6. Go to page 18 for the next step.

8x20 BASE KIT ASSEMBLY INSTRUCTIONS(GRA-BAS-8) AND (GRA-ASC-8XA) AND (GRA-ASC-4X)

HOLE FOR ANCHOR

16

STE

P O

NE

BA-C4

BA-S5 BA-S2

BA-S03ML01

BA-C4BA-S10

BA-S10

BA-C4BA-S10

BA-S10

GRANDIO



237 5/8” / 6036 mm

97 7/16”

/ 2475 m

m

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

BA-S1

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

BA-S1

HOLE FOR ANCHOR

BA-S1

BA-S2

BA-S1

BA-S2

BA-C3

BA-C3

BA-S3

BA-S4

BA-C3

BA-C4

BA-C3

BA-S4

BA-S3

8x24 BASE KIT ASSEMBLY INSTRUCTIONS(GRA-BAS-8) AND (GRA-ASC-8XA) AND (GRA-ASC-8XA)

1.7 Layout all base kit pieces to prepare for assembly. Note that one BA-S1 will be at the front and BA-S1 will be at the back and the BA-S2’s will be on the sides attaching to the front BA-S1. The BA-S3 and BA-S4 will attach to the back BA-S1. The BA-S3 will attach to the other BA-S3 and BA-S4 will attach to the other BA-S4 See diagram . 1.8 Attach the BA-S2 to the BA-S3 with the BA-C4 using the BA-S03 and ML01.See . Repeat for other side connecting the BA-S4 and the BA-S2, and then the BA-S3 to the BA-S3, and then the BA-S4 to the BA-S4. Go to page 18 for the next step.

17

STE

P O

NE

BA-C4

BA-S3 BA-S2

BA-S03ML01

BA-C4BA-S10

BA-S10

BA-C4BA-S10

BA-S10

GRANDIO



BA-C4 284 3/8”/ 7223 mm

97 7/16”

/ 2475 m

m

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

18

STE

P O

NE

1.9 Slide the BA-C3 into the BA-S1, slide the BA-S2 into the BA-C3, align the holes and push together to an even and tight position and use the BA-S03 Bolt and ML01 Collard Nut combo, tighten the collard nut on the inside of the base kit using the 10mm wrench. Repeat this process on all corners. See and . Note: BA-S1 will be the front and back, while the BA-S2’ s will be the sides of your greenhouse base.

1.10 For Ground Installation only Insert the BA-S03 and the BA-A1 into the holes at the bottom side of the corners of the base, the nut will be tightened on the inside of base, see and . Locate the anchoring devices for your installation needs and follow the directions for that anchoring system. If you have not purchased an anchoring system please go to www.GrandioGreenhouses.com for anchoring kit options.

BASE KIT ASSEMBLY INSTRUCTIONS

BA-S1

BA-S2

FRONT

SIDE

BA-C3

BA-S03ML01

BA-C3

BA-S1

BA-S2

BA-S03

ML01 Collared Nut

BA-S03

ML01 Collared Nut

BA-S03

BA-C4

BA-S3 BA-S2

BA-S03ML01

BA-S10

HOLE FOR ANCHOR

HOLE FOR ANCHOR

OutdoorGround

Assembly

1.11 If using an L-Bolt / BA-A1 anchoring kit the BA-A1 must be buried in ground. See .Dig holes to bury the BA-A1’s, you determine size and depth for your location. We recommend you use: Quikrete fast setting concrete to anchor base. Follow the directions on the package.See www.GrandioGreenhouses.com for anchoring kit options.

BASE KIT GROUND INSTALLATION

BA-S2

BA-A1

BA-S1

BA-S03 BA-A1 * Must be inserted into the ground, and secured with concrete.

GRANDIO

T I PMake sure base is squared and level before setting

anchor into concrete. Use a measuring tape to ensure all corners are the same. Use level on all four sides.

**BASE MUST BE LEVEL & SQUARE, FOUNDATION MUST BE PROPERLY ANCHORED PRIOR TO GREENHOUSE ASSEMBLY

19

STE

P O

NE

20

STE

P O

NE

1.12 Holes are present in base kit for anchoring bolts see and . You determine and acquire proper fastener prior to installation for your surface. Discard the BA-S10 for deck or concrete slab installation.See www.GrandioGreenhouses.com for anchoring kit options.

Use lag boltor concrete anchors

to attach base. (Fasteners not included).

B

Deck or Patio

Assembly

Use an appropriate fastener to attach to your surface through these access holes.

BA-C4

BA-S6 BA-S2

BA-S03ML01

BA-S1

BA-C3

BA-S2

HOLE FOR ANCHORBOLT OR SCREW.

BASE KIT DECK INSTALLATION**BASE MUST BE LEVEL & SQUARE,

FOUNDATION MUST BE PROPERLY ANCHORED PRIOR TO GREENHOUSE ASSEMBLY

GRANDIO

T I PMake sure base is squared and level before setting

anchors. Use a measuring tape to ensure all corners are the same. Use level on all four sides.

If surface is uneven you may wantto purchase large washers that will fit under the base and allow fasteners to go through to use as a shim for leveling the base kit.

This picture shows the inside view of front section fully assembled.All parts for this section will be found in boxes GRA-ASC-8A and GRA-ASC-8P.

We recommend that you assemble the front wall on a tarp.* If you purchased the Back Door Transformation kit you will repeat this section for your

back wall using parts found in GRA-ASC-BD, GRA-ASC-8A and GRA-ASC-8P boxes.If you want to purchase the Back Door Transformation kit call 1-866-448-8231.

601B

L08A-X

601B

Y3-2

603A

603C

L08D / 603B

L08A-X604-R

601A-FL601A-FR

Y3-1

Y1Y1604-L

619

W02 W02

W02TW02T

W01

W04

L08D / 603B

GRANDIO

T I PLay �at on ground to assemble the front frame of

your greenhouse. If possible try to �nd a shady area protected from the wind. Panels can burn grass and plants if in direct light.

GRANDIO

T I PWe recommend watching our how to assembly videos

with tricks and tips for easier assembly and installation of your Grandio Greenhouse at: www.grandiogreenhouses.com

GRANDIO

T I PBOLT INSTALLATION TIP: Locate all nuts and bolts, pre

thread and place in the groove of the extrusion to make installation easier. Move up or down for exact placement.

Inside View606-WS 606-WS

21

STE

P T

WO

Y2-2 Y2-1

FRONT FRAME ASSEMBLYALWAYS ASSEMBLE FRONT HORIZONTAL

2.1 Use W01 bracket to attach the (2) 601B’s together with the 603C, secure parts with the S05 fasteners provided as shown in . Pre thread W01 fasteners with S05 for ease of installation, only turn a few times. Screw heads will remain outside channel.

2.2 Insert Y3-1 and Y3-2 window panels as shown in .

2.3 Attach 603C and 603A with W04 and S04/ML01 fasteners as shown in .

2.4 Attach W02T to 601B and 603A with the S04/ML01 fasteners as shown in , leave a bit loose to ease installation of next step.

Y3-1Y3-2

601B 601B

603A

603C

W01

W02TW02T

W04

Inside View

W01

601B601B

603C

S05

S04ML01

W04 603C

603A

S04/ML01W02T

603A

601B

Transparent Clear Film

Opal White Film


Sun

The UV-Protected side is covered with clear �lm and must face toward the sun. The side covered in white �lm will always face the interior of the greenhouse. We suggest you peel all �lm o� completely prior to assembly and use a permanent marker to place a small “X” on the lower right corner of each panel on the clear side that faces the sun, each panel has a sticker labeling the panel number and this side always faces the sun or outward as well. DO NOT REMOVE LABELS UNTIL YOU INSTALL PANELS. The “X” is suggested in case you dis-assemble your greenhouse in the future so you may identify which side has the UV coating. Always use gloves when handling the polycarbonate panels as the edges can be very sharp.

IMPORTANT: POLYCARBONATE PANELS

22

STE

P T

WO

Inside View

IMPORTANT: Use only S05 Screws, other screws may damage frame.

FRONT FRAME ASSEMBLY CONTINUEDALWAYS ASSEMBLE FRONT HORIZONTAL

*IF USING THE MOISTURE CONTROL KIT YOU WILL USE IT NOW

S04

ML01

604-R

619

601A-FL601A-FR

604-R 604-L

619

INSIDE DOOR FRAME

GRANDIO



A

TIP: If necessary you may use a screwdriver to wedge behind the bolt head. This prevents bolt from falling into the track.

S04

601A-FR

ML01619

2.5 View diagrams and attach the (2) 604‘s and (2) 601A’s to the 619 with the S04/ML01 nut and bolt combos. Note the orientation of the 601A-FR and 601A-FL and the holes that should be at the top of the piece and face to the front, see the diagram to the right. shows where the corner pieces attach to 619.

shows where the door frame attaches to the 619.

*If assemblling the back door you will need to drill 1/4” holes in 601A-B’s to match the front wall, these holes should face the ground during assembly.

INSIDE Inside View

Inside View

INSIDE

OUTSIDE

INSIDE OUTSIDE

INSIDE

OUTSIDEOUTSIDE

INSIDE

GRANDIO

T I PMake sure the hole on the 601A-FL and 601A-FR

face to the front of greenhouse for future install of the L21 and L28 bracket that holds the door header in place.

NOTE HOLESON 601A SHOULD FACE FRONT OF GREENHOUSE

23

STE

P T

WO


2.6 Attach 606-WS to 619, this will hold the polycar-bonate panels in place. If it seems too tight slide �ngers or nut driver along edges, gently stretching the 606-WS to allow room for panels to �t .

2.7 Insert Y1 polycarbonate panels into place, make sure Y1’s slide completely into 606-WS as shown in .

2.8 Set (2) 603B’s atop the Y1 panels, then attach (2) L08D’s to the 603B’s, 601A’s and 604’s using S04/ML01 fasteners, make sure it is snug with the tops of the Y1 panels, then tighten fasteners. See and .

2.9 Insert the Y2-2 and Y2-1 polycarbonate panels into the track of the 603B.

L08DL08D

Y1 Y1

604-L604-R

619 606-WS

606-WS

601A-FL

Polycarbonate panel

606

619

A

601A-FR

GRANDIO

T I P Transparent Clear FilmOutside Greenhouse

Opal White FilmInside Greenhouse

Polycarbonate Panel

Sun

Inside View

OUTSIDE

A

S04/ML01

603B

L08D

601A-FR

604A-R

601A-FR 604-R603B

L08D

Y2-1Y2-2

603B 603B

24

STE

P T

WO


603A

601B

603C

601B

Y3-2 Y3-1

604-R

Y-1 Y-1

W02W02

601A-FL601A-FR 604-L

FAT END DOWN

S05W02T W02T

FAT END DOWN

Y2-2 Y2-1

W02

601B

FAT END

S05

W02

601B

601A-FR

S04ML01

W02T

604-R

601B603A

2.10 Move roof and front section together and align the W02’s into the 601A’s, and align the S04/ML01’s on the W02T’s into the 604’s. Insure a snug �t between the W02T’s, 601B’s and 601A’s and then tighten the S05 screws as shown in . Tighten the W02T’s with the S04 /ML01 nut and bolt as shown in .

25

STE

P T

WO

L08D L08D


2.11 Attach the (2) L08A-X ‘s to 601A’s and 604’s. See and .

2.12 To square front section loosen S04/ML01 attached to the tops of the (2) L08A-X’s, square the frame with carpenter square or use a measuring tape to make sure corner measurements are the same, tighten L08X’s to hold square-ness, L08A-X should be attached 1” up from bottom bolt see .

601B

L08D

L08A-X

601BY3-2

603C

L08D

L08A-X

604-R

601A-FR 601A-FL

Y3-1

Y1Y1604-L

619

W02 W02

W02TW02T

Y2-2 Y2-1

603A

GRANDIO

T I PSet front aside in a shaded area, do not lay on grass,

prolonged sunlight through the polycarbon-ate panels will burn if placed directly on top of plants during the intense sun of the day.

Use measuring tape to measure from corner to corner to assure square.

L08A-X601A-FR

S04/ML01

606-WS 606-WS

ML01 S04

L08A-X 619

26

STE

P T

WO

604-R


601B

L08B-X

601B

Y4-2

602C

L08B

L08B-X

602D

601A-B 601A-B

Y4-1

Y1Y1602D

W02 W02

Y1Y1

W01

L08A

W04-1 W04-1

603BY2-2 Y2-1

GRANDIO



Inside ViewGRANDIO

T I PMake sure the UV coated side of the panel faces

outward as indicated on the panels. Avoid placing the polycarbonate panels in the sun or near plants until fully assembled.

GRANDIO



Polycarbonate Panel

Sun

603B 603B603B

606-WS606-WS

27

STE

P T

HR

EE

BACK ASSEMBLY INSTRUCTIONSALWAYS ASSEMBLE BACK HORIZONTAL

This image shows the inside view of the back wall assembly.All parts for back assembly will be found in box GRA-ASC-8A and GRA-ASC-8P.

We recommend that you assemble the back wall on a tarp.* If you are using the Back Door Transformation Kit you will skip this section.

3.1 Prethread all S05 Screws into the W01 and W02’s, only turn a few times, see .

3.2 Use W01 bracket to attach the (2) 601B’s together as shown in diagram .

Attach (2) W02’s to the (2) 601B’s as shown in diagram .

3.3 Attach (2) 601A-B’s to L08A using S04/ML01 fastener as shown in diagram .

Attach (2) 602D’s to L08A using S04/ML01 fasten-ers as shown in diagram .

Attach 602C to L08A using S04/ML01 fastener as shown in diagram .

601B

601B

W01

601B601B

S05

L08A

W01

W02 W02

Inside View

601A-B602D602C602D601A-B

W02

601B

FAT ENDDOWN

602D

L08AINSIDEML01

601A-B

L08A

S04 INSIDE

ML01

S04

602C

L08A

W02 W02W01

FAT END

FAT END

28

STE

P T

HR

EE

BACK CONTINUEDALWAYS ASSEMBLE BACK HORIZONTAL

602C 602D

L08B

603B 603B

602D

606-WS

L08A

Y1Y1

Y4-2 Y4-1

3.4 Attach (4) 606-WS’s to L08A as shown in diagram .Insert the Y1 polycarbonate panels into the grooves of 601A-B’s, 602D’s and 602C. Make sure Y1 panels are inserted into 606-WS as shown in .

3.5 Set (4) 603B’s on top of the Y1’s that are now in place. Attach L08B to (2) 601A-B’s, 602D’s and the 602C with S04/ML01 fasteners as shown in diagram , and , . Pre thread all fasteners into assigned channels and align with L08B for ease of installation.

3.6 Insert the Y2-1 , Y2-2, Y4-1 and Y4-2 poly-carbonate panels into place as shown in the diagram to the right.

Y1Y1

603B 603B

L08B602C

Polycarbonate Panel

606-WS

L08A

603CL08B

602CS04

ML01

L08B

601A-B

601A-B601A-B

Inside View

603B603B

Y2-1Y2-2

603B

602D

L08B

29

STE

P T

HR

EE


3.7 Attach the roof to the back wall use W01 fastener to 602C and the (2) W02’s to the (2) 601A-B’s using the S05 fasteners as shown in diagram and , pre thread all screws for easiest installation, tighten when flush with frame and square.

602C

601A-B601A-B

Y4-1Y4-2

Y1Y1 Y1Y1

W01

601B601B

S05

602C

W01

W02 W02

603B 603B W02

601B

601A-B

FAT ENDDOWN

Inside View

L08A

Y2-1Y2-2

603B603B

602D602D

30

STE

P T

HR

EE

L08B


L08B-X601A-B

ML01 S04

602D

L08B-X L08A

3.8A. Attach the W04-1 to the 602D and 601B with S04/ML01 fasteners as shown in .

B. Attach (2) L08B-X’s to (2) 602D’s and L08A with S04/ML01 as shown in .

C. Attach (2) L08B-X’s to the (2) 601A’s with fasteners as shown in .

L08B-X L08B-X

GRANDIO

T I PSquare by loosening bolts attached to the tops of the

L08B-X, use measuring tape to make sure corner to corner measures the same.

602D

601B

S04/ML01W04-1

Inside View

602D 602D

S04/ML01

31

STE

P T

HR

EEBACK CONTINUED

ALWAYS ASSEMBLE BACK HORIZONTAL

601A-B 601A-B

2

1

MIDDLE ASSEMBLY INSTRUCTIONS

GRANDIO

T I PYou will need a minimum of (2) people to complete the

middle assembly of your greenhouse. The more people the merrier at this stage of assembly.

Warning: The person(s) holding the front or back sections vertical must continue to do so until the L08C-X angle supports are attached securely to the front and base as shown in step 4.5. Failure to hold front vertical will cause the front to fall and damage the base kit, front framing etc. Damage caused by improper installation is not warrantable.

ML01/NUT

S04 BOLTW05CLIP

32

STE

P F

OU

R

BA-S2

601A-FR

ML01S04

Inside ViewFront Right side

BA-S1

**This Base shows a 8x12, your greenhouse may be longer and configured of more base kit pieces.

BA-S2

BA-S1 BA-S5

BA-S6

4.1 We recommend pre threading all (9) W05 Clips with the nut and bolt combos now. See , note the bolt head will always slide into the extru-sion, W05 clips will be used in step 4.5.

4.2 With no less than 2 people place the pre assembled front section on top of the base kit front. Have person (1) hold the front vertically while the other attaches the front section 601A’s to the base using S04/ML01 fasteners as shown in .Person (1) must continue to hold up the front wall!

If building a greenhouse with a front and back door you will repeat steps 4.1-4.5 for attaching both front and back walls of the greenhouse.

33

STE

P F

OU

R

MIDDLE ASSEMBLY CONTINUED

601A

601B

L08A-X

L08C-X L08D

L08C-X

Base

4.3 Attach L08C-X to 601A and the BA-S2 with (3) S04/ML01 on both sides as shown in and with the nut and bolt combos.4.4 Attach the front section 619 to the base using S10/ML02 fasteners as shown in , then attach the 619-BAR threshold support to the inside of the 619 with (5) S19 self tapping screws included in the package, see .

2

1

BA-S1

604

601A

601A619-BAR will attach with the (5) S19screws

619 Attaches to the base kit with S10/ML02

L08C-X

L08C-X

2

1

4.5 Have one person hold the front vertically while the other attaches the font section to the base with W05/S04/ML01 fasten-ers as shown in , and . The (4) W05 clips will catch the under edge of the front base kit and then slide upward attach-ing to the bottom of the 601A’s and the 604’s, you will switch out the S04/ML01 that was originally used to the W05 Clip Combo. If you are having a di�cult time at the corners tightening the ML01 �anged nuts you may switch to the ML02 non �anged nuts for easier installation.

BA-S1

BA-S2

BA-S1

604

601A-FL

601A-FR

BaseBA-S1

W05619

Inside


BA-S5

BA-S6

34

STE

P F

OU

R

BA-S2

601A-FRML01S04

Inside View

W05

BA-S1

ML01 S04

L08A-X 619

604-R

W05

L08C-X

L08C-X602D

602D

602C

601A-B

35

STE

P F

OU

RMIDDLE ASSEMBLY CONTINUED

4.6 Attach back wall 601A-B’s with back base corners using S04/ML01 on both sides as shown in .

4.7 Attach bottom of L08C-X to rear section of base kit with S04/ML01, as shown in . Attach the L08C-X to the 601A-B as shown in , make sure the S04/ML01 combos are tight.

4.8 Use the (5) remaining W05 clips to attach the backwall where the 601A-B’s meet the corner of the base as shown in , and where 602D’s, and the 602C meet the BA-S1B see . Then use W05 Clip combos to attach the corner 601A’s to the base kit as shown in , you will switch out the S04/ML01 that was originally used to the W05 Clip Combo.

601A-B

601B

L08B-X

L08C-X L08B

W05

Base

602C, 602D

Outside

Inside

BA-S2 orBA-S6

601A-B

ML01S04

Inside ViewBack Left side

BA-S1

L08C-X

Base

Back Wall BA-S1601A-BML01S04

BA-S2 orBA-S6

Inside View

W05

Back Base

Back Base

If you are using the Back Door Transformation kit you will repeat steps 4.1-4.5 to install the Back Door Wall, then skip ahead to step 4.9.

601A-B

36

STE

P F

OU

R

Repeat these steps if you are building an 8x20 or 8x24 with your last extension box, note it is best to connect 8x8, then 8X, then an 4X if assembling an 8x20. Note that the notches shown in should be spaced every 2 feet, none should be right next to each other.

4.9 Attach the 607 to 607-4X or 608-8X extension with the 607-XS and the (4) S08 screws provided see , . The S08 screws are to be installed on the inside as shown in diagram . Wait to tighten the screws all at one time when both sections are aligned correctly, apply even pressure while tightening.

4.10 Apply a bead of silicone to the seam where the 607’s meet and to the holes where the S06 screws will attach the DP01 to the 607 ridge. See . Immediately align the DP01 apply a small amount of silicone to the holes on the exterior of DP01 then insert the S06 screws.

607-8X

607607-XS

For 8x20 and 8x24 Grandio Ascent Assembly


607-XS

607-8X

607

DP01

FRONT

S08

WARNING

Notches

Notches

APPLY SILICONE CAULKTO RIDGE AND HOLES

S06

607

607-8X

FRONT

S06

DP01


607

607

601B 601B

Inside View

Side Angle View

607

601B 601B

Inside View

S04/ML01

4.11 With 2 people, attach the ridge to front and back by sliding into place as shown in and , using S04/ML01 fasteners attach the 607 to the 601B’s. See for how the �nal orientation should be.

607

37

STE

P F

OU

R

607-4X

EXTENSION ASSEMBLY INSTRUCTIONS

Warning: You will need a minimum of 2 people to complete this section, you will not be able to stop assembly until page 44. Note that if you are assembling an 8x20 or an 8x24 greenhouse you will proceed thru the 2nd extension assembly instruc-tions. Damage caused by improper installation is not warrantable. It will be helpful to prepare and lay each section and necessary parts out prior to beginning this sections actual assembly, pre reading will make this section much easier.

GRANDIO

T I PBOLT INSTALLATION TIP: Locate about 30 nuts and

bolts and pre thread for easiest installation.

Warning: This section will take about 30 minutes to complete. Be prepared to �nish as there is not a stopping point until page 44 for an 8x12 or 8x16 or page 50 for an 8x20 or 8x24, depending on your greenhouse con�guration. Note it may be helpful to have a few more people at this point the more the merrier.

38

STE

P F

IVE

5.1 Connect the (2) braces labeled L08M-X together with the nut and bolt combo S04/ML01 see . The combined L08M-X’s should measure about 94 1/2” when connected together.

5.2 Attach the 602A to the base with a nut and bolt combo where the extension kit meets on the base kit, with other person holding the 602A in place. Measure down 6” from the top of the 602A to attach the W14 bracket to the 602A on both sides with the S04/ML01 . See and . Attach the assembled L08M-X’s to the W14 as shown in and .

5.3 Have one person keep holding the 602A and L08M-X on one side for support while you prepare for next step on the next page.

BASE

602A

6”

W14

602A

L08M-X W14

W14 BRACKET


BA-S2

Measure 6”

602A

L08M-X

602A

607

Measure 6”

39

STE

P F

IVE

L08M-XL08M-X

Back

Back

Front IMPORTANT TO HAVE THE L08M-X

FACE THE BACK AS SHOWN

5.4 Attach the 609 to the (2) 609-XS’s with (4) of the S09 screws provided see and . The S09 screws are to be installed on the inside of the 609 and will tighten into the 609-XS as shown in the diagrams. Repeat with other set, note they will be opposite of each other when assembled.

Pay special attention to the orientation of the 609, make sure the correct side faces down, see .

609

Profile View

Groove


40

STE

P F

IVE

UP

609

609-XSFRONT

INSIDE VIEW

UP

S09

UPFRONT

OUTSIDE VIEW

609-XS

609

1

2

L08D L08C-X601A

LOOSENML01

Inside View

GRANDIO




601B

1

2

L08C-X 601A

601A

L08C-X

601B

601B

602A

607

602A

609601B

41

STE

P F

IVE

601B

609

S04/ML01

L08C-XL08D

Inside View

601A

5.5 With 2 people proceed to install 609 in this order, note that 609 must be installed with groove side down see .

1. With one person holding the 609 level and in position have the other person loosen the top of the L08C-X and let it fall free, attach the 609 to the 601B using S04/ML01 (nut and bolt). See and .

2. Now move the loosened S04/ML01 (nut and bolt) currently attached to the L08C-X upward to secure the 609, 601A-F and L08C-X together as shown in .

3. Have assistant keep holding at the middle section . Turn to next page for detailed installation.

UP

601B

609

Profile View

Groove

601A

Note the line on the 609 that shows the exact placement of the 601B’s and the 601A’s when installedcorrectly.

2

1

42

STE

P F

IVE

L08C-X 601A

601A

L08C-X

601B

601B

602A

607

602A

609

609

4. Note the top of 602A should touch the line on the 609 for exact placement, see . Attach the 609 to the 602A with the S04/ML01 nut and bolt combos see diagram .

5. Repeat steps 1-4 on the other side see .


OUTSIDE VIEW

602A

NOTE EXACT PLACEMENT OF THE 602A TO THE 609.

EXACTPLACEMENT LINE FOR 602A

FRONT

609

609INSIDE VIEW

609-XS

FRONT

S04/ML01

43

STE

P F

IVE

602A

607

602A

609

602B

2

5.6 With person 1 holding the 609 steady person 2 will attach the 602B’s between the 609 and 607 on both sides. See and .


1

Outside View

609

ML01/S04

602B

Inside View

602A

602A

NOTE EXACT PLACEMENT OF THE 602A AND 602B TO THE 609.

FRONT

602B 609

44

STE

P F

IVE

602A

607

602A

609

AZ-1

AZ-1

BZ-1

2

1

5.7 Connect the AZ-1 with the W17 and included hardware, see . With two people attach the AZ-1 to the base and the lower 602A, see . Then attach the upper end to the mid roof line see . Install on both sides of the greenhouse where the extension seams meet using the S02/ML01 combo.

5.8 Install the BZ-1 to the upper mid roof, to act as the support to the peak of the roof as shown between the (2) 602B’s with S04/ML01 nut and bolt combos, see .

IF YOUR GREENHOUSE IS AN 8X12 OR 8X16 SKIP TO PAGE 50. IF YOURS IS AN 8X20 OR 8X24 PROCEED ON TO THE NEXT PAGE.


AFTER COMPLETING STEP 5.9

602A

AZ-1

S02/ML01

INSIDE VIEW

W17 BRACKET

S02/ML01You will need to switch this bolt out to an S02

FRONT

AZ-1

ML01W17 BracketNote orientationof bracket

S02

(7mm gap edge will fitdown into base bottom)

10mm7mm

1

5.9 Connect the (2) braces labeled L08M-X together with the nut and bolt combo S04/ML01 see . The combined L08M-X’s should measure about 94 1/2” when connected together.

5.10 Attach the 602A to the base with a nut and bolt comboMeasure down 6” from the top of the 602A to attach the W14 bracket to the 602A on both sides with the S04/ML01. See and . Attach the assembled L08M-X’s to the W14 as shown in and .

5.11 Have one person keep holding the 602A and L08M-X on one side for support while you prepare for next step on the next page.

BASE

602A

6”

W14

Measure 6”

L08M-X

602A

Measure 6”602A

L08M-XL08M-X

W14 BRACKET

602AL08M-X W14

2nd EXTENSION ASSEMBLY INSTRUCTIONSCONTINUE FOR 8X20 AND 8X24 ONLY / FOR 8X12 AND 8X16 SKIP AHEAD TO PAGE 50 OR STEP 5.17

45

STE

P F

IVE

INSIDE VIEW

IMPORTANT TO HAVE THE L08M-X FACE THE BACK AS SHOWN

Back

Front

5.12 Attach the 609 to the (2) 609-XS’s with (4) of the S09 screws provided see and . The S09 screws are to be installed on the inside of the 609 and will tighten into the 609-XS as shown in the diagrams. Repeat with other set, note they will be opposite of each other when assembled.

Pay special attention to the orientation of the 609, make sure the correct side faces down, see .

609

Profile View

Groove

2nd EXTENSION ASSEMBLY INSTRUCTIONS

46

STE

P F

IVE

CONTINUE FOR 8X20 AND 8X24 ONLY / FOR 8X12 AND 8X16 SKIP AHEAD TO PAGE 50 OR STEP 5.17

609

609-XSFRONT

INSIDE VIEW

UP

S09

UPFRONT

OUTSIDE VIEW

609-XS

609

609

Profile View

GrooveGRANDIO



5.13 With 2 people proceed to install 609 extension at the eave.

1. With one person holding the 609 level and in position have the other person attach the 609 to other end of the 609-XS as shown in .

2. With one person holding the 609 level and in position have the other person attach the 609 to the 602A using S04/ML01. See .

3. Repeat steps 1. and 2. on other side of the greenhouse.


1602A609

609

47

STE

P F

IVE


609

609--4X-L or 609-8X-LINSIDE VIEW

609-XS

FRONT

S09

602A

NOTE EXACT PLACEMENT OF THE 602A TO THE 609.

EXACTPLACEMENT LINE FOR 602A

FRONT

609

1


5.14 Attach the (2) 602B’s between the 609 and 607 on both sides. See and .

Outside View

Inside View

602B

602A

602A

607

609

609

48

STE

P F

IVE


602A

NOTE EXACT PLACEMENT OF THE 602A AND 602B TO THE 609.

FRONT

602B 609

609

INSIDE VIEW

FRONT

S04/ML01

609-4X-L609-8X-L

BACKS04/ML01

602A

602B

1

602B

602A

602A

607

609

609


AZ-1AZ-1

BZ-1602B

5.15 Connect the AZ-1 with the W17 and included hardware, see . With two people attach the AZ-1 to the base and the lower 602A, see . Then attach the upper end to the mid roof line see . Install on both sides of the greenhouse where the extension seams meet using the S02/ML01 combo.

5.16 Install the BZ-1 to the upper mid roof, to act as the support to the peak of the roof as shown between the (2) 602B’s with S04/ML01 nut and bolt combos, see .

49

STE

P F

IVE


602A

AZ-1

S02/ML01

INSIDE VIEW

W17 BRACKET

S02/ML01You will need to switch this bolt out to an S02

FRONT

AZ-1

ML01W17 BracketNote orientationof bracket

S02

(7mm gap edge will fitdown into base bottom)

10mm7mm

5.17 With two people attach the 609 extension to 609-XS with the (4) S09 screws provided see and .

5.18 With person 1 still holding in place have person 2 loosen the L08C-X nut and bolt combo to attach the 609 into place, see .

Repeat these steps on other side of the greenhouse, see .

601B609

609

609

602A

607

602A

609

2

1

601A-B

609

MIDDLE ASSEMBLY INSTRUCTIONS CONTINUED

50

STE

P F

IVE

601B

609

S04/ML01

L08C-XL08B

Inside View

601A

609FRONT

S04/ML01

609-4X-L or 609-8X-L

BACKS04/ML01

602A

FRONT

602B 609609-XS

BACK609-4X-L or 609-8X-L

INSIDE VIEW

OUTSIDE VIEW

S09

609

609

602A

607

602A

609

602A602A

602A

602A

602A

602A

L08C-XS04ML01BASE

Inside View

609

602A

Inside View

BA-S2

602A

Inside View

ML01/S04ML01/S04


51

STE

P F

IVE

5.19 Before you attach the 602A’s to the sides of the greenhouse you will need to loosen the ML01 (nut) attached to the L08C-X and the base. See diagram .

1. Once the bottom of one L08C-X is loosened set the 602A onto the bolt of the L08C-X. Be sure the 602A is aligned and sitting �ush on top of the base kit. See for reference.

2. Hold the 602A in place and attach the top of the 602A to the 609 using S04/ML01 (nut and bolt). As shown in .

3. Repeat steps 1. and 2. on all four corners where the L08C-X ‘s meet the base kit.

4. Now attach the bottom of 602A to the Base using a S04/ML01 (nut and bolt) as shown in , and to the 609 with an S04/ML01 combo as is shown in .

5. Repeat step 4. on all places where a 602A should go. You may reference diagrams at front for your exact size.

Note: Where the L08C-X reattaches to the BASE and the 602A be sure to secure them tightly see .

Loosen only one L08C-X at a time.

L08C-X

L08C-X

SUN

616 615PC sheet

5.20 Assemble the roof window vents as shown below in and , using the Z02 screws attach the 615, 616, and 618’s with the Y8 panel as shown, be careful not to strip the screw heads. Pay attention to the Y8 panel, stickers face the sun, and that the frames are assembled according to images below.

5.21 Insert assembled window into the end of ridge of 607 and slide into position. See . Window positions are your discretion however, must be in the middle for support, do not place nearest the front or back, nor right next to each other as you will need a 602B support to keep in window vent in place. Place directly across from each other for best cross draft ventilation, see for optional placement. Attach the 602B’s as shown between and , after all roof vents are positioned.** It is recommended to apply silicone caulk to the exterior seams on the bottom and sides of each panel, where panels meet the frame for water resistance, or see the Moisture Control Kit on our website to maintain panel clarity. The interior and top of each panel is protected so it is recommended that you leave them un-caulked allowing the panels to breathe.

GRANDIO

T I PPlace roof windows in desired location before

attaching all 602B’s.

Y8

618

Z02

Z02

Z02

Z02

Z02618

Screwdriver Outside View

615

616

618616

Z02

Note Correct Orientation


616

618

615607

SUN

609

607

609

Y8

Y8602B

52

STE

P F

IVE

602B

602B

602B602B

Y8

Inside of window

606-WS

PC sheet

BASE GRANDIO

T I PMake sure the UV coated side of the panel faces

outward as indicated on the panels. Avoid placing the polycarbonate panels in the sun or near plants until fully assembled.

602A

4.16 Install plastic strip 606 before inserting polycarbonate sheet Y7’s.

4.17 After Y7’s are installed, loosen bolts attached to L08C-X in all upper corners. Using a level, adjust 602A and tighten bolts. Repeat in every corner until the greenhouse is level. The top edges of Y7’s will align when greenhouse is level.

S04/ML01

L08C-X

609

Loosen

5.22 Install plastic strip 606-WS before inserting polycarbonate sheet Y6’s, see . Install all Y6 panels into the channel’s of the side walls, and �t down into the 606-WS.

5.23 After Y6’s are installed, loosen bolts attached to L08C-X in all upper corners. Using a level, adjust 602A and tighten bolts. Repeat in every corner until the greenhouse is plumb. The top edges of Y6’s will align when greenhouse is level or plumb. See .

OUTSIDE

Y9Y9

Y9

606-WS

BASE

Y6

Y6

Y6

Y6

Y6Y6

Y6Y6

Y6Y6

Y6Y6


53

STE

P F

IVE

5.24 To ensure there is no gap in roof vent position 603B as shown in . Connect 603B to middle of 602B’s using W04 bracket as shown in .

5.25 Attach HQC01 to 616 with the Z04 screws see , close roof vent and attach the handle onto HQC02 middle pin (the �rst two holes of the handle to the second and third pins of HQC02). Then attach HQC02 into 603B’s track with S04/ML01 (nuts and bolts), see .

603B

618

616

616

603B

616

Z04

HQC02

Y8

Y8

HQC01Handle

Note: If you are installing automatic roof vent openers follow those directions for correct installation.SAVE MANUAL OPENERS FOR WINTER SWITCHOUT.

HQC01Handle


HQC01Handle

Y8

Y8

Y8

54

STE

P F

IVE

Inside view of 603B603B

602BW04

603B

HQC02

HQC01Handle

ML01/S04

Inside View

1 2 3

Outside

insideInside

Outside607609-WS

609-WS

PC Sheet PC Sheet609-WS

PC Sheet

5.26 Attach 609-WS to the inner roof line of the 607 and on both top and bottom of 609 as shown in and .

GRANDIO

T I PNote that there are two parts labeled 609 &

609-WS, one is the gutter support, the other is a clip that �ts under polycarbonate panels inside greenhouse.

609


55

STE

P F

IVE

607

609

609

Y8

Y8

5.27 Insert polycarbonate sheets Y7’s and Y9’s into the roof of your greenhouse. Panels may slide out before gutters are in place. You may want to place a piece of tape on the panel to prevent sliding as shown in the diagram once the panels are in place.

5.28 Slide 610 Gutters into 609’s groove as shown in diagram . Repeat on both sides. Note the orientation of the gutters, the extension gutters will be at the back and the holes should align with gutter down spout holes see next page.


Y7

Y9

Y8

Y7

Y7Y7

Y9

601B

601A

610

609

609

610

Gutter

Outside View

56

STE

P F

IVE

The two profiles should be flush at ends when installed correctly.

DP02B

DP02

610-4X-L or 610-8X-L

610

5.29 Apply a small amount of the silicone caulk to the seam where the 610 gutters meet, then attach the DP02 on the inside of the gutter and the DP02B will slide under the gutter and will rest above the 602A. Apply silicone to the holes where the S07 screws will attach the 610 gutters to the DP02 and DP02B. Note the DP02B has pre-tapped holes to accept the screws and hold tight. See diagram and .

Repeat these steps to assemble the additional set(s) for both sides of your greenhouse.Remove the tape from the panels you may have used to hold in place.


DP02

610-4X-L or 610-8X-L

610

602A

602B

57

STE

P F

IVE

5.30 Attach end caps to the ridge and gutters on both front and back as shown below. Squeeze a small amount of rubberized silicone or construction adhesive into the ends of ridge (607) to secure pressure �t end caps (601). It is recommended to caulk any areas that may allow water penetration such as at the gutter end caps and at the base corners to seal against water as shown in .

5.31 It is recommended to apply silicone caulk to the seams where panels meet the frame for water resistance.

J602A-E

Z03

J602B-E

Z03

Z03

601

J602B-E

Z03

J602B-E

Z03

J602A-E Z03

J601

610

58

STE

P F

IVE


607

INTERIOR ROOF SUPPORT ASSEMBLY 6.1 Attach the BZ1’s to the roof line as shown in diagram with the S04/ML01. Use CZ1’s to support the interior wall at the eave using the S04/ML01. See diagram .

6.2 Use S04/ML01 to attach the L08C’s to 601B’s and 602B’s on the inside of roof midway between the roof and the gutters for additional roof support. See diagram .

6.3 Remove the L08M-X support combo, take apart and now and install to the sides of the AZ1 extension brace, see . Save the hardware and W14 bracket for possible future use or hang inside as a plant hanger clip.

BZ1

CZ1

L08C

Y8

Y8

Y8

Y8

CZ1

BZ1

602A

602B

602B

602B

L08C L08C

602B

602B

609

602B

59

STE

P S

IX

L08M-X

DOOR ASSEMBLY DIAGRAM

Z01622

Y5

Y5

622-R

UP

UP

Catch

620Z01

Z01

Z01

Z01

Z01

623B

623A622Side View

622

J08A

BottomView

623B

620

623A

J08A

J08A

622-R

UP

UP

Side View

622

J08A

BottomView

Inside View

60

STE

P S

EV

EN

J04OPTIONAL

This image shows the inside view of Right Door Assembly.All parts for door assembly will be found in box GRA-ASC-8A and GRA-ASC-8P.

Use the #2 head Phillips Screw Driver for installation.If you are using the Back Door Transformation kit you will repeat steps 7.1-7.11 to install the Back Door,

these parts will be found in box GRA-ASC-BD.

You may need to gently open the channel with a flat head srewdriver if screws are not going into place with ease.

623B

623A

622

J08A

BottomView

J08A

We recommend you lay out all parts for both doors to make sure they match up correctly for hanging. Double check the orienta-tion of what is inside verses outside and how the doors will hang on page 63-65. Make sure window panels face the right direction to the sun and note that the panels have predrilled holes for the handles to attach later and these need to be aligned with the lock mechanisms, you may have to drill these out if they are not visible. This will save you from assembling the wrong way. 7.1 Insert J08A into the bottom of the 622, note the bottom groove is smaller than the top groove of 622, see .7.2 Use the Z01 screws to attach the 622 to the 623B, 623A and 620 as shown in .7.3 Insert Y5 windows into position as shown in .

623B

Z01

620Z01

Z01623B

623A

622 620

623A

622

620

Y5

Y5

GRANDIO



Polycarbonate Panel

Sun

622

UP

UP

Side View

Inside View

DOOR ASSEMBLY

61

STE

P S

EV

EN

J04OPTIONAL

J08A

622

J08A

BottomView

Side ViewOf Top

* DoubleBall Catch

on the 622-L

622-L

UP

UP

Side ViewOf Bottom

7.4 Insert J08A into the bottom of the 622-R and 622-L, note the bottom has a groove see .7.5 Attach the 622-R to the 623B, 623A and 620 using the Z01 screws as shown in .7.6 Follow the same instructions for the other door making sure that the 622-L and 622-R with the double ball catch match up so doors will latch closed and slide properly .

Y5

Y5

623B

623A

620

622-R

Catch

Z01

Z01

Z01

622-R

Side ViewOf Top

* Catch on the 622-R

622-R

UP

UP

Side ViewOf Bottom

* Note the orientation of the 622-L and 622-R. Also make sure the right side is facing out on the Y5 polycarbonate panels.

Inside View622

DOOR ASSEMBLY CONTINUED

62

STE

P S

EV

EN

DOOR INSTALLATION7.7 Slide the (2) S02 bolts down the track of the L21 see , align with the holes on the 603A door header. With one person inside the greenhouse line up hanging door track L21 with door header 603A, move bolts on L21 to line up with bolt holes on door header 603A. From the inside hand tighten the ML01 nut while the person outside is holding the L21 in position, you will now center on the front of the greenhouse and tighten the S02/ML01 combo.

S02

L21

1

2

603A

63

STE

P S

EV

EN

2

Side Profile View of L21 Hanging Track

Inside View

Track

S02SCREW

S04 S04S02

7.8 Separately slide the top of the doors in the left and right side of L21, see diagram , until they latch in the middle.

7.9 Attach the door handles 622-HNDL to both doors using the 622-HNDL-NUT/BOLT provided to both doors as shown below in , and .

DOOR INSTALLATION

Outside View Inside View

Top

Bottom

Side Profile View of Hanging Track

L21 L21

622-HNDL

622-HNDLNUT/BOLT

622-HNDL

622-HNDLNUT/BOLT

64

STE

P S

EV

EN

DOOR INSTALLATION

You may remove all stickers now with Goo Gone remover if needed. You are now finished with assembly!

J07

603A

L21

L28

S04/ML01

Top View

601A

S02

L28

S02

601A-FRML01

65

STE

P S

EV

EN

Top Profile View

7.10 Attach L28 to L21 with S04/ML01, and L28 to 601A with S02/ML01 as shown below in diagram and . Check that the L21 and L28’s are square. Attach (2) J07 to the ends of L21 see . The L28 should align square to the 601A.

7.11 Check that the door locks are snug, you may adjust them with screwdriver if needed as they can be tightened or loosened.

601A-B

601A-FL

601A-FR

601B

602A

602B

602C

602D

603A

603B

603C

604-R

604-L

606-WS

607

609-WS

609

610

615

616

618

619 PACK 619-BAR

S19 SCREWS10 / ML02

BZ-1

CZ-1

L08ANOTE THESE ARE

PACKED TOGETHER

L08B

52 1/2 in / 1334 mm BACK CORNERS

52 1/2 in / 1334 mm FRONT LEFT CORNER

52 1/2 in / 1334 mm FRONT RIGHT CORNER

57 1/8 in / 1451 mm CORNER ROOF

52 1/2in / 1334 mm

57 1/2 in / 1451 mm

87 1/4 in / 2216 mm

70 3/8 in / 1787 mm

47 5/16 in / 1201 mm

21 7/8 in / 555 mm

17 in / 431 mm

68 7/8 in / 1750 mm FRONT RIGHT

68 7/8 in / 1750 mm FRONT LEFT

21 3/4 in / 553 mmWINDOW SEAL

94 1/4 in / 2394 mm


94 1/4” in / 2394 mm

94 3/8 in / 2397 mm

22 3/4 in / 578 mm

22 3/4 in / 578 mm

19 3/4 in / 500 mm

94 1/4 in / 2394 mm40 in / 1015 mm

M4*10M6*16

23 5/8 in /600 mmROOF SUPPORT

19 11/16 in / 500 mmEAVE SUPPPORT

94 1/4 in / 2394 mm

94 1/4 in / 2394 mm

BLACK WINDOW SEAL

GRAPHIC PART NAME SIZE/LOCATION QUANTITY GRAPHIC PART NAME SIZE/LOCATION QUANTITY

2

1

1

4

6

6

1

2

1

8

1

1

1

14

1

22

2

2

2

2

4

1-6191-619 Bar

5 - S19 Screws3 - S10 / ML02

3

6

1

1

(GRA-ASC-8A) GRANDIO ASCENT 8’X8’ ALUMINUM PACKING LIST

66

PAR

TS

LIST

FO

R G

RA

-ASC

-8A

L08C

L08D

L08A-X

L08B-X

L08C-X

W01

W02

W02T

W04

W04-1

Z01

Z02

Z03

94 1/4 in / 2394 mm

24 3/4 in / 614 mm

48 7/8 in /1242 mm

48 7/8 in / 1242 mm

57 5/16 in / 1456 mm

ROOF

FRONT & BACK

FRONT & BACK

ROOF LINE

BACK WALL

M4*30Screws for Doors

M3.5*16Screws for Roof Vents

M3*25Screw for End Caps

S02

ML01/S04

S05

J601

J602A-E

J602B-E

L28

W11

W13

W16

HQC01

HQC02

Z04, S04/ML01

M6*25

M6*14

M6*10For W01 and W02

END CAPS

END CAPS

END CAP

22 in /558 mm

SCREW DRIVER

10 MM NUT DRIVER

10 MM WRENCH

ROOF VENT ARM

ROOF VENT LATCH

ROOF VENT HARDWARE

2

2

2

2

4

2

4

2

5

2

13

9

4

6

140

30

2

2

2

2

1

1

1

2

2

4 EACH

GRAPHIC PART NAME SIZE/LOCATION QUANTITYGRAPHIC PART NAME SIZE/LOCATION QUANTITY


67

PAR

TS

LIST

FO

R G

RA

-ASC

-8A

622-HNDL

622-HNDLNUT/BOLT

620

L21

622

622-R

622-L

623A

623B

J04

J07

J08A


4

4

2

1

2

1

1

2

2

4

2

4

DOOR HANDLES

DOOR HARDWARE

21 7/16 in / 545 mm

95 1/2 in / 2425 mm

67 7/8 in / 1724 mm

67 7/8 in / 1724 mm

67 7/8 in / 1724 mm

21 7/16 in / 545 mm

21 5/16 in / 542 mm

DOOR BOTTOM ROLLER

L21A END CAP

DOORS


68

PAR

TS

LIST

FO

R G

RA

-ASC

-8A

AZ-1 / W17 S02/ML01

ML02

76 3/4 in / 1950 mmEXTENSION SUPPORT

NON FLANGED NUT


2

8

69

PAR

TS

LIST

FO

R G

RA

-ASC

-8P

Y1

Y2-1

Y2-2

Y3-1

Y3-2

Y4-1

Y4-2

Y5

Y6

Y7

Y8

Y9

LOWER BACK WALL PANEL

FRONT UPPER SIDEWALL

FRONT UPPER SIDEWALL

FRONT UPPER PEAK

FRONT UPPER PEAK

BACK MIDWALL

BACK MIDWALL

DOOR PANEL

SIDE PANEL

ROOF PANEL

ROOF VENT PANEL

UNDER ROOF VENT

GRAPHIC PART # SIZE/LOCATION WIDTH HEIGHT 1 HEIGHT 2 QTY

6

2

2

1

1

1

1

4

8

6

2

2

22 3/4 in / 578 mm

22 3/4 in / 578 mm

22 3/4 in / 578 mm

22 3/4 in / 578 mm

22 3/4 in / 578 mm

22 3/4 in / 578 mm

22 3/4 in / 578 mm

22 3/4 in / 578 mm

22 3/4 in / 578 mm

22 3/4 in / 578 mm

22 3/4 in / 578 mm

22 3/4 in / 578 mm

44 in / 1118 mm

8 1/4in / 209 mm

25 5/16 in / 643 mm

11/16 in /18 mm

17 3/4in / 451 mm

25 3/41 in / 654 mm

42 13/16 in /1088 mm

33 in / 839 mm

53 in / 1346 mm

58 1/8 in /1477 mm

19 1/8 in / 486 mm

36 7/8 in / 937 mm

25 5/16 in / 643 mm

8 1/4 in / 209 mm

17 3/4 in / 451 mm

11/16 in /18 mm

42 13/16 in /1088 mm

25 3/41 in / 654 mm

(GRA-ASC-8P) GRANDIO ASCENT 8’X8’ PANEL PACKING LIST

(GRA-ASC-4XA) GRANDIO ASCENT 4’ EXTENSION ALUMINUM PACKING LIST

602A

602B

603B

L08M-X

L08C

BZ-1

CZ-1

607-4X

607-XS

S08

S06

DP01

52 1/2 in / 1334 mm

57 1/8 in / 1451 mm

21 7/8 in / 555 mm

57 5/16 in / 1456 mm

46 3/4 in / 1187 mm

23 5/8 in / 600 mmROOF SUPPORT

19 11/16 in / 500 mmEAVE SUPPORT

47 1/2 in / 1187 mm

ROOF EXTENSION

M6*20Attaches the 607-XS to 607

M4*6Attaches DP01 to 607

ROOF CAP


4

4

1

2

2

2

2

1

1

5

3

1

606-WS

609-WS

609-4X-R609-4X-L

609-XS

S09

610-4X-R610-4X-L

DP02

DP02B

S07

615

616

618



46 3/4 in / 1187 mm

609 EXTENSION CONNECTORS

M4*6ATTACHES 609-XS TO 609’s

46 3/4 in / 1187 mm

GUTTER BRACKET CONNECTOR

GUTTER BRACKET CONNECTOR

M5*8ATTACHES DP02 TO DP02B

22 3/4 in / 578 mm

22 3/4 in / 578 mm

19 3/4 in / 500 mm

BLACK WINDOW SEAL


4

11

2

4

20

2

2

2

5

1

1

2

70

PAR

TS

LIST

FO

R G

RA

-ASC

-4X

S04/ML01

W04

W14

Z02

HQCO1

HQC02

Z04, S04/ML01

M6*14

ROOF VENT

L08M-X BRACKET

M3.5*16SCREWS FOR ROOF VENTS

ROOF VENT ARM

ROOF VENT LATCH

HQC01 HARDWARE

40

2

2

5

1

1

2/2


(GRA-ASC-4X) GRANDIO ASCENT 4’ EXTENSION ALUMINUM PACKING LIST

71

PAR

TS

LIST

FO

R G

RA

-ASC

-4X

72

PAR

TS

LIST

FO

R G

RA

-ASC

-4X

Y6

Y7

Y8

Y9

SIDE PANEL

ROOF PANEL

ROOF VENT PANEL

UNDER ROOF VENT PANEL


4

3

1

1

22 3/4 in / 578 mm

22 3/4 in / 578 mm

22 3/4 in / 578 mm

22 3/4 in / 578 mm

53 in / 1346 mm

58 1/8 in /1477 mm

19 1/8 in / 486 mm

36 7/8 in / 937 mm

(GRA-ASC-4X) GRANDIO ASCENT 4’ EXTENSION PANEL PACKING LIST

602A

602B

603B

L08M-X

L08C

AZ-1 / W17S02/ML01

BZ-1

CZ-1

607-8X

607-XS

S08

S06

DP01

52 1/2 in / 1334 mm

57 1/8 in / 1451 mm

21 7/8 in / 555 mm

57 5/16 in / 1456 mm

93 1/4in / 2394 mm

76 3/4 in / 1950 mmEXTENSION SUPPORT



93 7/16 in / 2374 mm

ROOF EXTENSION

M6*20ATTACHES 607-XS TO 607

M4*6ATTACHES DP01 TO 607

ROOF CAP


8

8

2

2

2

2

4

6

1

1

5

3

1

606-WS

609-WS

609-8X-R609-8X-L

609-XS

S09

610-8X-R610-8X-L

DP02

DP02B

S07

615

616

618



93 7/16 in / 2374 mm

609 EXTENSION

M4*6ATTACH THE 609-XS TO 609

93 7/16 in / 2374 mm

GUTTER BRACKET

GUTTER BRACKET

M5*8SCREW FOR GUTTER BRACKET

22 3/4 in / 578 mm

22 3/4 in / 578 mm

19 3/4 in / 500 mm

BLACK WINDOW SEAL


8

22

2

4

20

2

2

2

5

2

2

4


73

PAR

TS

LIST

FO

R G

RA

-ASC

-8X

A


S04/ML01

W04

W14

Z02

HQCO1

HQC02

Z04, S04/ML01

M6*14

ROOF VENT BRACKETS

L08M-X BRACKET

M3.5*16SCREWS FOR ROOF VENT

ROOF VENT ARM

ROOF VENT LATCH

HQC01 SCREW

65

4

2

9

2

2

4


74

PAR

TS

LIST

FO

R G

RA

-ASC

-8X

A

75

PAR

TS

LIST

FO

R G

RA

-ASC

-8X

P

Y6

Y7

Y8

Y9

SIDE PANEL

SIDE PANEL

ROOF VENT PANEL

UNDER ROOF VENT


8

6

2

2

22 3/4 in / 578 mm

22 3/4 in / 578 mm

22 3/4 in / 578 mm

22 3/4 in / 578 mm

53 in / 1346 mm

58 1/8 in /1477 mm

19 1/8 in / 486 mm

36 7/8 in / 937 mm

(GRA-ASC-8XP) GRANDIO ASCENT 8’ EXTENSION PANEL PACKING LIST

76

PAR

TS

LIST

FO

R G

RA

-ASC

-BD

47 5/16 in / 1201 mm BACK CORNERS

17 in / 431 mm FRONT LEFT CORNER

68 7/8 in / 1750 mm FRONT RIGHT DOOR

68 7/8 in / 1750 mm FRONT LEFT DOOR

24 3/16 in / 614 mm

94 1/4 in / 2394 mm40 in / 1015 mm

M4*10M6*16

67 7/8 in / 1724 mm

67 7/8 in / 1724 mm

67 7/8 in / 1724 mm

21 7/16 in / 545 mm

21 7/16 in / 545 mm

21 5/16 in / 542 mm FRONT RIGHT

BOTTOM DOOR ROLLER

(GRA-ASC-BD) GRANDIO ASCENT BACKDOOR PACKING LIST

603A

603C

604R

604L

L08D

619 PACK619-BAR

S19S10 / ML02

622

622-R

622-L

620

623A

623B

J04

J08A

Z01

ML01/S04

ML01/S02

L21

J07

L28

W04

W02T

Y3-1

Y3-2

Y5

1/4 DB


1

1

1

1

2

1-6191-619 Bar

5 - S19 ScrewsS10 / ML02

2

1

1

2

2

2

4


4

13

30

4

1

2

2

1

2

1

1

4

1

DOOR

M4*30SCREWS FOR DOORS

M6*14

M6*25

95 1/2 in / 2425 mm

L21 ENDCAP

22 in / 558 mm FRONT RIGHT

CONNECTOR BRACKET

DOOR FRAME

UPPER ROOF PANEL

UPPER ROOF PANEL

DOOR PANELS

1/4 DRILL BIT

77

WA

RR

AN

TY

Grandio Greenhouse Limited Lifetime Warranty

1. Grandio Greenhouses are warranted to the original purchaser to be free from defects in material or workmanship for ten years from the date of original retail purchase on all plastic panels. Additionally the aluminium frame is warrantied for life. The word “defects” is de�ned as imperfections that impair the use of the product.

2. Defects resulting from misuse, abuse or negligence will void this warranty. This warranty does not cover defects due to improper installa-tion, alteration or accident. This warranty does not cover damage caused by vandalism, rusting, “acts of nature” or any other event beyond the control of the manufacturer.

3. This warranty is nontransferable and is expressly limited to the repair or replacement of defective product if the product is defective within the terms of this warranty, Grandio Greenhouses will repair or replace defective parts at no cost to the purchaser. Shipping charges to and from the factory or distribution center are not covered and are the responsibility of the purchaser. Labor charges and related expenses for removal, installation or replacement of the greenhouse or its components are not covered under this warranty.

4. This warranty does not cover scratching or scu�ng of the product that may result from normal usage. In addition, defects resulting from intentional damage, negligence, unreasonable use will void this warranty.

5. Liability for incidental or consequential damages is excluded to the extent permitted by law. While every attempt is made to embody the highest degree of safety in all equipment, freedom from injury cannot be guaranteed. The user assumes all risk of injury resulting from the use of this product. All merchandise is sold on this condition, and no representative of the company may waive or change this policy.

6. This product is not intended for institutional or commercial use; Grandio Greenhouses does not assume any liability for such use.

7. This warranty is expressly in lieu of all other warranties, expressed or implied, including warranties of merchantability for use to extent permitted by Federal and State Law. Neither Grandio Greenhouses nor any representative assumes any other liability in connection with this product. This warranty gives you speci�c legal rights, and you may also have other rights that vary from state to state.

52 1/2 in / 1334 mm

57 1/8 in / 1451 mm

21 7/8 in / 555 mm

57 5/16 in / 1456 mm

46 3/4 in / 1187 mm



47 1/2 in / 1187 mm

ROOF EXTENSION

M6*20Attaches the 607-XS to 607

M4*6Attaches DP01 to 607

ROOF CAP

NOTES NOTES


®

GREENHOUSE USER MANUALKEEP IN A SAFE PLACE FOR REFERENCE

CONTACT US IF YOU NEED HELPOR

HAVE MISSING OR DAMAGED PARTS

GRANDIOGREENHOUSES.COM

BACKYARD LIVING SOURCE, INC.9543 W. EMERALD ST., SUITE 101

BOISE, ID 83704

1-866-448-8231

Grandio Ascent 8x12, 8x16, 8x20 & 8x24 Models

Grandio Ascent EXTENSION KIT Manual April 14 2016

Documents

Transcript of Grandio Ascent EXTENSION KIT Manual April 14 2016