GRAND PIANO HARDWARE AND · PDF file140 GRAND PIANO HARDWARE AND ACCESSORIES No. 965 No....
Transcript of GRAND PIANO HARDWARE AND · PDF file140 GRAND PIANO HARDWARE AND ACCESSORIES No. 965 No....
139
GRAND RAIL PROP NUTSSlotted grand rail prop nutsfor replacement. Solid Brass.No. 925 - Each
FERRULES OR LEG SOCKETSFor grand piano legs. Polished brass.No. 964A - 1-1/2” inside dimension at top; 5/8” high. EachNo. 964B - 1-3/4” inside dimension at top; 1-1/2” high. EachNo. 964C - 2-1/8” inside dimension at top; 2” high. Each
LID SUPPORT CUPNo. 938 - Solid brass. EachNo. 938N - Nickel plated. Each
GRAND DESK RESTWith staple and rubber cap. 7-1/8” long from knuckle to end.3 countersunk holes.No. 941 - Brass. EachNo. 942 - Nickel Plated. EachNo. 941C - Extra Rubber Cap. Per DozenNo. 941A - Brass Staple. EachNo. 942A - Nickel Plated Staple. Each
GRAND PIANO LEVERSCast iron: black Japanned.No. 1074 - Each
GRAND ACTION BRACKETIt is best to remove the old brackets off each end and refit newones, aligning the new with old center brackets; if necessary,use a maple block to get the proper spacing by placing theblock underneath the bracket so the top of the bracket is thesame as the old one. When the end brackets are lined up andscrewed in place, repeat the procedure and replace the centerbrackets. You are now ready to regulate the action.No. 1076 - For Aeolian. Each
GRAND ACTION SHIFTER SPRINGSDouble-end type. No. 16 gauge blued steel.No. 962 - Double end type. 8-7/16” x 1-3/4”. EachNo. 963 - Square end. 5-5/16 x 1-3/4”. Each
GRAND KEYBOARD SPRINGSBlued steel. 5-5/16” x 1/2”; .082 thick.No. 959 - Each
No. 962
No. 963
STEINWAY SOSTENUTO PEDAL SPRINGNo. 961 - Each
STEINWAY FALL BOARD SPRINGSUsed at friction end of grand fall board.No. 960 - Each
STEINWAY DAMPER FRAME SPRINGNo. 1201 - Each
HAMMER REST RAIL BOLTS2-3/4" Long. Includes nuts. 5 pieces per set.No. 1027 - Set
GRAND PIANO LEG PLATESFor fastening legs to grands. Made ofcast iron. No filing required in fitting.Interchangeable. Round style; smallerplate dia. 3-1/4”; larger plate 4-1/4”.2 plates per unit, 3 units in a set.No. 966 - Per Set
GRAND PIANO HARDWARE AND ACCESSORIES
140
GRAND PIANO HARDWARE AND ACCESSORIES
No. 965
No. 965PS
GRAND PIANO LOCKComplete with plunger, escutcheon and key. Satin brass finish.Selvage plate 5/8” x 4-1/16” Plunger plate 3/4” x 4-1/16”No. 965 - Complete Lock. EachNo. 965K - Extra Key for above. EachNo. 965PS - Plunger Sticker. EachNo. 965E - Escutcheon. Each
No. 965K
No. 965E
GRAND PIANO KEY FRAME SCREWNickel-plated steel.No. 1070 - Each
AGRAFFE SHIMMING WASHERSThin brass washers for shimming agraffes.3/8” diameter, 17/64” hole, .010” thickNo. 922 - Per 100
AGRAFFESSolid Brass, threaded agraffes for Steinway and other grands.Available in one, two or three string holes. American Style. 7/32" X 36 ThreadsNo. 926S - Single. EachNo. 926D - Standard Double. EachNo. 926DW - Wide Double for Steinway. EachNo. 926T - Triple. Each
1/4" x 36 ThreadsNo. 927S - Single. EachNo. 927D - Standard Double. EachNo. 927DW - Wide Double. Each No. 927T - Triple. Each
GRAND LOCK ESCUTCHEONDesigned to fit Steinway, some Mason &Hamlin & some Kimball Pianos. Available onlyin raw brass ready for polishing or plating.No. 965ES - Each
LYRE BRACES – BRASS PLATED5/16” diameter.No. 970 - 13” long. Per PairNo. 971 - 21” long. Per Pair
GRAND PIANO DESK SLIDESPolished brass. 14” long.No. 1072 - Per Pair
GRAND LID SUPPORTLong flap is 12” overall from center of pin; short flap is2” long.No. 935 - Solid brass; polished. EachNo. 936 - Solid brass; nickeled. Each
GRAND FALL BOARD HINGESBrass.No. 1068 - Per Pair
SOLID BRASS PEDAL RODSSolid brass, satin finish.No. 972 - With adjustable collar. 21-1/2” x 1/4” dia. Set of 3No. 773 - With hex cap and nut. 19-3/4” x 5/16” dia. Set of 3
BRASS PLATED PEDAL RODSOne end milled other end threaded. Furnished with nuts.20-1/4" Long.No. 1003 - Set of 3
LYRE BRACES - SOLID BRASS5/16” diameterNo. 770A - 12-13/16” long, 4 screw holes. Per PairNo. 770B - 14” long, 4 screw holes. Per PairNo. 770C - 21” long, 4 screw holes. Per PairNo. 771 - 23” long, 2 screw holes. Per Pair
STEINWAY GRAND LOCK KEYAn original replacement part.No. 965KS - Each
STEINWAY PEDAL RODSAn original replacement part.No. 1004 - With hex nut. 20-3/16" Long. Set of 3
141
GRAND PIANO PEDALS
Solid brass, polished. Overall length 7”. 2-7/16” from centerof pin to center of lyre rod hole. 15/16” from center of pin toback of horn.No. 992 - Set of 3
Solid brass, polished. Overall length of center pedal 7-3/4”,left and right 7-1/4”. 3” from center of pin to center of lyrerod hole. 1-1/8” from center of pin to back of horn.No. 991 - Set of 3
Solid brass, polished. Overall length 7-1/2”. 2-3/4” fromcenter of pin to center of lyre rod hole. 1-5/16” from centerof pin to back of horn.No. 974 - Set of 3
Solid brass, polished. Overall length 7-3/4”. No horn.3-1/16” from center of pin to center of lyre rod hole.No. 975 - Set of 3
Solid brass, polished. Overall length 8-3/8”. 3-1/4” fromcenter of pin to center of lyre rod hole. 1-7/16” from centerof pin to back of horn.No. 976 - Set of 3
Solid brass, polished. Overall length of center pedal 7-3/8”,left and right 7”. 2-5/16” from center of pin to center of lyrerod hole. 1-1/8” from center of pin to back of horn.No. 993 - Set of 3
Solid brass, polished. Overall length of center pedal 8-5/8”,left and right 8-1/4”. 3-1/4” from center of pin to center oflyre rod hole. 1-1/16” from center of pin to back of horn.No. 994 - Set of 3
142
GRAND PIANO PEDALS
Solid brass, polished. Overall length 8”. 3-7/16” from centerof pin to center of lyre rod hole. 1-3/8” from center of pin toback of horn.No. 998 - Set of 3
Solid brass, polished. Overall length 8”. No horn. 2-3/8”from center of pin to center of lyre rod hole.No. 1000 - Set of 3
Solid brass, polished. Overall length 9”. No horn.2-13/16” from center of pin to center of lyre rod hole.No. 1002 - Set of 3
Solid brass, polished. Overall length of center pedal 7-7/8”,left and right 7-7/8”. 3-3/16” from center of pin to center oflyre rod hole. 1-1/8” from center of pin to back of horn.No. 995 - Set of 3
Solid brass, polished. Overall length 7-1/4”. 2-3/8” fromcenter of pin to center of lyre rod hole. 1-1/4” from center ofpin to back of horn.No. 996 - Set of 3
Solid brass, polished. Overall length 6 7/8”. 2-11/16” fromcenter of pin to center of lyre rod hole. 1-1/8” from center ofpin to back of horn.No. 997 - Set of 3
STEINWAY PEDALS WITH PLATEAvailable in polished brass or satin nickel. Will fit anySteinway grand piano. No. 1005 - Polished Brass. SetNo. 1006 - Satin Nickel. Set
143
UPRIGHT PIANO PEDALS
Cast iron, nickel plated. Right and left pedals 8-5/8” long,back of horn to center of pin 5”. Center pedal 9-7/8” long.Back of horn to center of pin measures 2-1/2”No. 1573 - Set of 3
Solid brass. 9” long. Back of horn to center of pin 5”.No. 1577 - Set of 3
Solid brass. Right and left pedals 8-3/8” long. Back of horn tocenter of pin 4-13/16”. Center pedal 9-5/8” long. Back ofhorn to center of pin 5-3/4”.No. 1570 - Set of 3
Solid brass. 8-1/2” long. Back of horn to centerof pin 4-13/16”.No. 1571 - Set of 3
Cast iron, brass plated with knurled brass toe button. Rightand left pedals 8-3/8” long. Back of horn to center of pin4-7/8”. Center pedal 9-1/2” long. Back of horn to center ofpin 5-3/4”. Center pedal mount 2-1/2” back of horn to center.No. 1575 - Set of 3
Solid brass, polished. Right and left pedals 9-3/16” long.Center pedal 9-3/16” long. No horn.No. 1576 - Set of 3
144
UPRIGHT PIANO PEDALS
Solid brass. 9” long. Back of horn to center of pin 6-1/4”.No. 1580 - Set of 3
Cast iron brass cap. 8-3/8” long, back of horn to center of pin5-1/2”. Center pedal with interchangeable steel pin at end orcenter. Back of horn to center of pin 3”.No. 1581 - Set of 3
Solid brass. 8-7/8” long. Back of horn to center of pin 5”.No. 1582 - Set of 3
Cast solid brass pedal. 8-1/8” long. Back of horn to center ofpin 4-3/8”.No. 1583 - Set of 3
Cast iron, nickel plated. Right and left pedals 9-3/8” long.Center pedal 9-3/4” long. No horn. No. 1579 - Set of 3
Cast iron, nickel plated. Right and left pedals 9” long. Centerpedal 9-3/4” long. No horn. No. 1578 - Set of 3
145
UPRIGHT PIANO PEDALS
Cast solid brass. 8-3/4” long. Back of horn to centerof pin 5-1/4”.No. 1586 - Set of 3
Solid brass. Right and left pedals 8-1/2” long, back of horn tocenter of pin 4-7/8”. Center pedal 9” long. Back of horn tocenter of pin 5-3/8”.No. 1585 - Set of 3
Cast solid brass pedal 9-1/8” long. Back of horn tocenter of pin 5-5/16”.No. 1584 - Set of 3
Solid brass. 9” long. No horn.No. 1593 - Set of 3
Cast iron, nickel plated. Right and left pedal 9” long. Back ofhorn to center of pin 5-1/2”. Center pedal 9-3/8” long. Backof horn to center of pin 5-3/4”.No. 1589 - Set of 3
Solid Brass. 8-5/8" Long. Back of horn to center of pin 4-7/8".Suggested as excellent replacement sets for most uprightpianos.No. 1599 - Set of 3
146
PIANO PEDAL HARDWARE AND ACCESSORIES
FELT PEDAL COVERS & TIESRed felt with red stitching.No. 578 - Set of 3
PEDAL EXTENSIONSPermit children to operate pedals from natural sittingposition. Adjusts to any height. Very easy to attach...doesnot interfere with use of master pedals. Nickel plated.No. 1845 - Per PairNo. 1845R - Right Pedal Only. Each
FLUTED PEDAL PINS2” long x .156 diameter.No. 2584 - Each
PEDAL PROPSComplete with square nuts. Available in following lengths:2-1/8”, 4”, 4-1/2”, & 5”.No. 579-2-1/8 - EachNo. 579-4 - EachNo. 579-4-1/2 - EachNo. 579-5 - Each
NORRIS TOE BUTTONSFor replacement on worn pedals. Button diameter 1-3/16”.Shaft diameter 1/4”.No. 2585 - Set of 3
RUBBER PIN BUSHINGSFor covering fallboard stop pins, trap pins and for pedalprop bushings.No. 340 - 3/8” high, 1/4” stem dia., 3/8” base dia.,
1/8” hole. EachNo. 340A - 5/16” high, 11/32” stem dia., 9/16” base dia.,
1/8” hole. Each
STEEL PEDAL BRACKETSTo replace cast iron type. Feature Nylon bearings. Bracketsare stamped steel, with gusset bend at flange for extrastrength. Mounting center of bearing is 3/4” from base.No. 2587 - Nickel Plated. Per pair
STEEL PEDAL BRACKETSWith nylon bushing.No. 2589 - Per pair
NYLON PEDAL BRACKETSNo. 2590 - Per pair
147
PIANO PEDAL HARDWARE AND ACCESSORIES
DESK SPRINGFor grand piano key board. Blue steel.No. 581 - Thin; gauge 23. 3-1/4” long. EachNo. 582 - Medium; gauge 21. 5” long. Each
PEDAL BRACKETSCast iron, with pivot point bearings.No. 2582 - Pedal Brackets. Set of 3
TRAP LEVER SPRINGNo. 593 - Each
CONICAL SPRINGUsed to slip under pedals to increase tension and force quickreturn. No screws necessary.No. 586 - Each
TRAP SPRINGFor pedal or trap action. Blue steel. 4” long.No. 583T - Thin; gauge 23. EachNo. 583M - Medium; gauge 21. EachNo. 583H - Heavy; gauge 19. Each
AEOLIAN AMERICAN GRAND ACTION SPRINGNo. 580 - Grand Action Spring. Each
NORRIS SPRINGMade of spring steel.No. 584A - 7/8” high. EachNo. 584B - 1-3/8” high. EachNo. 584C - 1-7/8” high. EachNo. 584D - 3-1/2” high. Each
TRAP LEVER SPRINGMade of spring steel. 4” x 7/8”.No. 587 - Each
TRAP PIN3" x .155" diameter.No. 3568 - Each
148
SOLID BRASS TOP HINGESAVAILABLE IN SATIN BRASSOR POLISHED NICKEL FINISH.
STEINWAY STRAIGHT STYLE HINGE (MODEL D)Overall Length 4-5/8". 2" wide.No. 2771-1/2B - Brass. EachNo. 2771-1/2N - Nickel. Each
TOP HINGE2” x 2-1/2” unequal leaves.No. 572B - Brass. EachNo. 572N - Nickel. Each
STEINWAY BENT BUTT HINGE (MODEL B)Length of fancy leaf to center of pin 4-5/8". 2" wide.Center of pin to inside of bend 1-3/8".No. 2774B - Brass. EachNo. 2774N - Nickel. Each
STRAIGHT STYLE HINGE5-7/8” x 2”.No. 569B - Brass. EachNo. 569N - Nickel. Each
STRAIGHT STYLE HINGE5-3/8” X 1-3/4”.No. 2569B - Brass. EachNo. 2569N - Nickel. Each
BENT BUTT STYLE HINGE 5-1/2” x 2”. Center of pin to inside of bend 7/8”.No. 669B - Brass. EachNo. 669N - Nickel. Each
BENT BUTT HINGE5-3/8” x 1-3/4”. Center of pin to inside of bend 7/8”.No. 2669B - Brass. EachNo. 2669N - Nickel. Each
BENT BUTT HINGEOverall length - 5-3/4”. Center of pin to inside ofbend 1-1/8”.No. 2770B - Brass. Each
STEINWAY BENT BUTT HINGE (MODELS M & L)Length of fancy leaf to center of pin 4-5/8". 2" wide.Center of pin to inside of bend 1-3/16".No. 2771B - Brass. EachNo. 2771N - Nickel. Each
STEINWAY BENT BUTT HINGE (MODEL S)Length of fancy leaf to center of pin 4-5/8". 2"wide. Center of pin to inside of bend 1-3/32".No. 2773B - Brass. EachNo. 2773N - Nickel. Each
149
HINGES AND HARDWARE
UPRIGHT PIANO LOCKS& ACCESSORIES
UPRIGHT PIANO LOCK KITKey, striker, escutcheonand lock.No. 553B - Lock Kit. Each
KEY - Triangle lock key.No. 554 - Each
BRASS THREAD ESCUTCHEONSNo. 555B - Dozen
STRIKER PLATENo. 556N - Nickel plated. EachNo. 556B - Brass. Each
SOSS INVISIBLE HINGESFor piano fall boards and key slips.Wherever an invisible joint is desired.Screws included. Plated steel.No. 5100N - Nickel. 1” long x 3/8” wide. EachNo. 5100B - Dull Brass. 1” long x 3/8” wide. EachNo. 5101N - Nickel. 1-3/4” long x 3/8” wide. EachNo. 5101B - Dull Brass. 1-3/4” long x 3/8” wide. EachNo. 5102B - Dull Brass. 1-1/2” long x 1/2” wide. Each
BUTT HINGES
SOLID BRASS IN CHOICE OF SATIN BRASS OR NICKELPLATED FINISH...STRAIGHT OR BENT BUTT STYLES.REMOVABLE HINGE PIN.
STRAIGHT HINGE2” x 3”.No. 568B - Brass. EachNo. 568N - Nickel. Each
BENT BUTT HINGE2” x 3”.No. 1568B - Brass. EachNo. 1568N - Nickel. Each
BUTT HINGE1-3/4” x 1”.No. 567B - Brass. EachNo. 567N - Nickel. Each
CONTINUOUS HINGESScrew holes uniformly spaced and countersunk for #4solid brass screws. Opens 1-1/16” wide. .040 thick. 5’ long.Solid brass.No. 565B - Brass. EachNo. 565N - Nickel. Each
STEINWAY STYLE ROUNDCORNER HINGES2” wide by 3-1/16”. Looseball tip pin. Solid brass.No. 570 - Brass. EachNo. 571 - Nickel. Each
TOP HINGE, REVERSE FLAP1-1/2” wide x 3-1/8” overall.Steel, brass plated.No. 2567-1/2 - Each
DESK SUPPORT HINGEFour flaps with countersunk screw holes. Solid brass, satinfinish.No. 940W - For grands. 1-3/8” wide x 10-7/8” long. EachNo. 940N - For grands. 1” wide x 9” long. EachNo. 940S - For spinets. 1” wide x 6-3/16” long. Each
STEINWAY STYLE SECTIONAL HINGEAn exact replacement. Consists of 11 sections measuring5" and 1 section measuring 4" held in place by acontinuous hinge pin that is 60-5/8" long. Opens 1-1/8"wide. Solid brass. Sold as 1 complete hinge.No. 565AB - Brass. EachNo. 565AN - Nickel. Each
MASON & HAMLIN STYLEDESK HINGESolid brass, satin finish fancy hinge.1-1/4" wide with 1/2" offset forMason & Hamlin grand music desks.No. 1095 - Hinge. Each
HINGES
KNIFE HINGE - Bright steel. 3-1/4”*.With bracket.No. 566-1/2 - Pair* Measurements are from center to center of screw holes,when hinges are open.
150
HINGES AND HARDWARE
STRUT HINGEFor piano tops. Saves those brokenhinges, when top is opened completely.Strut built into hinge supports top in open position.No. 1061 - 5/8” wide. Each
HINGE PINS
STEINWAY STYLE HINGE PINSFor that exact replacement that adds so much! Solid brass.No. 3569G - Straight Ball Tip Type. 2" x .150". EachNo. 3569H - Bent Type. 2" x .140". Each(same style as #3569A above)
PIANO BENCH HARDWARE
STEEL BENCH LEG BRACES3-1/8” W x 2-1/2” H.No. 577 - Each
LEG FERRULESID 1-1/8” W x 1-1/8” H.No. 677 - Each
BENCH HINGES–STEEL, BRASS PLATEDLength Width
Stock # Along Pin When OpenNo. 575 1-1/4" 1-1/8"No. 575A 1-1/4" 1-3/4"*No. 575A has unequal leaves.
LID SUPPORTSNo. 576 - Each
PANEL SPRINGSBlue steel; 13/16” WNo. 585A - 5” long. Each
FALLBOARD & MUSIC DESKHINGES & HARDWARE
FALLBOARD HINGESNo. 1062 - Brass. Pair
MUSIC DESK RESTHINGESIncludes fasteners.No. 1064 - Small. PairNo. 1065 - Large. Pair
FALLBOARD HINGESNo. 1066 - Brass. Pair
KNIFE HINGE - Bright steel. 3-1/4”*.Without bracket.No. 566 - Pair
FRONT FRAME CATCHESNo. 594 - Pair
SOLID BRASS HINGE PINSFor empire top hinges. Available in satin brass or nickelplated. EachStock# Length Diameter FinishNo. 3569A 2" .150" BrassNo. 3569B 2" .150" NickelNo. 3569C 1-3/4" .150" BrassNo. 3569D 1-3/4" .150" NickelNo. 3569E 1-1/2" .117" BrassNo. 3569F 1-1/2" .117" NickelNo. 3569K 1-3/4" .133" BrassNo. 3569L 1-3/4" .133" NickelNo. 3569M 1-3/4" .104" BrassNo. 3569N 1-3/4" .104" Nickel
BENCH LEG BOLTS, LOCKWASHERSAND NUTSNo. 1081A - 5/16" x 2". Per set of 4No. 1081B - 5/16" x 2-1/2". Per set of 4
PLASTIC NAIL GLIDESFor piano benches and other furniture.Silent, non-marking.No. 1085A - 5/8" Diameter. EachNo. 1085B - 3/4" Diameter. Each
CHANNEL BRASSRepair split or worn music desks quickly with these brass reinforcements. Also useful for new music desks to prevent damage and wear. Satin brass.No. 1092 - Grands. PairNo. 1093 - Spinets and Consoles. Pair
FALLBOARD ROD CLAMPReplacement for lost or brokenfallboard rod clamps.No. 1200 - Each
UPRIGHT PIANO HARDWARE
TOP FASTENERSUsed to hold upright piano topssecurely to prevent vibration andwarping. Spring type, bronze finish.No. 1098 - Pair
TOP LID SUPPORTFor upright pianos. Withrubber cap. 4" long.No. 560 - Each