GPSMAP 700 Series Installation Instructions -...
Transcript of GPSMAP 700 Series Installation Instructions -...
GPSMAP® 700 Series Installation Instructions WARNING
See the Important Safety and Product Information guide in the product box for product warnings and other important information.
CAutIoNAlways wear safety goggles, ear protection, and a dust mask when drilling, cutting, or sanding.
NoticeWhen drilling or cutting, always check what is on the opposite side of the surface to avoid damaging your boat.
The GPSMAP 700 series chartplotter must be properly installed according to the following instructions. You need the appropriate fasteners, tools, and mounts listed in each section. These items are available at most marine dealers.
Contact Garmin® Product Support if you have any questions while installing your GPSMAP 700 series chartplotter. In the USA, go to www.garmin.com/support, or contact Garmin USA by phone at (913) 397.8200 or (800) 800.1020. In the UK, contact Garmin (Europe) Ltd. by phone at 0808 2380000. In Europe, go to www.garmin.com/support and click Contact Support for in-country support information, or contact Garmin (Europe) Ltd. by phone at +44 (0) 870.8501241.
Before installing your GPSMAP 700 series chartplotter, confirm that the package contains the items listed on the box. If any parts are missing, contact your Garmin dealer immediately.
Product RegistrationHelp us better support you by completing our online registration today. Go to http://my.garmin.com. Keep the original sales receipt, or a photocopy, in a safe place.
For future reference, write the serial number assigned to your GPSMAP 700 series chartplotter in the space provided. The serial number is located on a sticker on the back of the device.
Chartplotter serial number: to install the GPSMAP 700 series chartplotter, you must:1. MounttheGPSMAP700serieschartplotter.2. Connectthechartplottertopower(page5).3. Ensurethatthechartplottersoftwareisup-to-date(page7).
the following additional installation options are not necessary in order to use the GPSMAP 700 series chartplotter. they have been included for your convenience:• ConnectingthechartplottertoaNMEA2000network(page6)• ConnectingthechartplottertoaGA30remoteGPSantenna(page6).• ConnectingthechartplottertoaGarminmarineradar(page6).• ConnectingthechartplottertootherNMEA0183-compatibledevicessuchasaVHFradiowithDSC(page5).• Connectingthechartplottertoasonartransducer(“s”modelsonly)(page6).
Mounting the ChartplotterYou can mount the GPSMAP 700 series chartplotters using one of two methods. You can use the included bracket and hardware to bail mount the chartplotter, or you can use the included template and hardware to flush mount the chartplotter.
Mount the GPSMAP 700 series chartplotter in a location that provides a clear, glare-free view of the display and easy operation of the power key and the touch screen.
February2010 PartNumber190-01155-02Rev.B PrintedinTaiwan
� GPSMAP 700 Series Installation Instructions
Bail Mounting the ChartplotterUse the included bracket to bail mount the GPSMAP 700 series chartplotter. You can route cables from under the mounting surface through the included bail-mount bracket, though it is not necessary. See page 3 for instructions on installing the bail-mount bracket without routing cables through the bracket.
Hardware (included):• Bail-mountbracket• Cable-organizationbracket• Bail-mounttemplate• Four35mmM4.2× 1.4screws(tosecurethebail-mountbracket)• Two20mmM3.5×1.3screws(tosecurethecable-organization
bracket)
tools required (not included):• Jigsaw• Drillanddrillbits—11/4in.(32mm),and1/8in.(3mm)• Number2Phillipsscrewdriver
to install the bail-mount bracket with the cables routed through the bracket:1. Usingtheincludedbail-mountbrackettemplate,determinethebestplacetoinstallthebracket.Besuretoleaveadequateclearancebehind
thechartplotterforthewiring. NotE:Toavoidinterference,mounttheGPSMAP700serieschartplotteratleast32in.(813mm)fromamagneticcompass.2. Thebail-mountbrackettemplatehasadhesiveontheback.Removethe
protectivelinerandapplythetemplatetothelocationatwhichyouwanttoinstallthebail-mountbracket.
3. Usea11/4in.(32mm)drillbittodrillthepass-throughholeinthecenterofthetemplate.
4. Useausea1/8in.(3mm)drillbittodrillthesixpilotholesmarkedonthebail-mounttemplate.
NotE: If you are mounting the chartplotter in fiberglass, it is recommended to use acountersinkbittodrillaclearance-counterborethroughonlythetopgel-coatlayer.Thiswillhelptoavoidanycrackinginthegel-coatlayerwhenthescrewsaretightened.
5.Removethebail-mountbrackettemplatefromthemountingsurface.6.Routethecablespertinenttoyourinstallationthroughtheholeyoudrilledinstep3,
fromunderthemountingsurface. Ifyouplantouseallfourcables,routetheminthefollowingordertoensurethat
they will all fit correctly:RadarcablePower/datawiringcableGA30GPSantennacableNMEA2000cable
NotE:Donotinstallthelockingring(page4)onthepower/dataorradarcableuntilafteryourouteitthroughthemountingsurface.7.Placethecable-organizationbracketaroundthecablesandintothe11/4in.(32mm)holeyoudrilledinstep3.8.Usethetwoincluded20mmM3.5×1.3screwstosecurethecable-organizationbrackettothemountingsurface. NotE: Stainless-steel screws may bind when screwed into fiberglass and
overtightened.Garminrecommendsapplyingananti-galling,stainlessanti-seizelubricanttothescrewbeforeusing.
9. Extend6–7in.(152–178mm)ofcableslackthroughthecableorganizationbracket,andsecureeachcabletothecorrectclips.Refertothecable-organizationbracketdiagramfortheclipassignments.
10.Placethebail-mountbracketoverthecable-organizationbracketandroutethecablesthroughthebackofthebail-mountbracket.
11.Securethebailmounttothesurfaceusingthefourincluded35mmM4.2×1.4screws.12.Followthestepsonpage3toinstalltheGPSMAP700serieschartplotteronthebail
mountbracket.Testtheslack-lengthofthecablesroutedthroughthebracket.13.Makecableslack-lengthadjustmentsifnecessary.Applymarinesealant(optional).
••••
Cable-organization bracket
Bail-mount bracket
GPSMAP 700 series chartplotter
Bail-Mounting the GPSMAP 700 Series Chartplotter
Cable-organization bracket
Bail-mount bracket
GPSMAP 700 series chartplotter
Bail-Mounting the GPSMAP 700 Series Chartplotter
Cable-Organization-Bracket Clip Identification
➊ ➋ ➌ ➍
➊ GA 30 GPS antenna cable clip
➋ Power/data cable clip
➌ Garmin Marine Radar cable clip
➍ NMEA 2000 cable clipCable-Organization-Bracket Clip Identification
➊ ➋ ➌ ➍
➊ GA 30 GPS antenna cable clip
➋ Power/data cable clip
➌ Garmin Marine Radar cable clip
➍ NMEA 2000 cable clip
GPSMAP 700 Series Installation Instructions �
to install the bail-mount bracket without the cables routed through the bracket:1. Usingtheincludedbail-mountbrackettemplate,determinethebestplacetoinstallthebracket.Besuretoleaveadequateclearancebehind
thechartplotterforthewiring. NotE:Toavoidinterference,mounttheGPSMAP700serieschartplotteratleast32in.(813mm)fromamagneticcompass.2. Thebail-mountbrackettemplatehasadhesiveontheback.Removetheprotectivelinerandapplythetemplatetothelocationatwhichyou
wanttoinstallthebail-mountbracket.3. Usea1/8in.(3mm)drillbittodrillthefourouterpilotholesmarkedonthetemplate.Donotdrillthetwopilotholesmarkedonthecable-
organizationbracket. NotE: If you are mounting the chartplotter in fiberglass, it is recommended to use a countersink bit to drill a clearance-counter bore through
onlythetopgel-coatlayer.Thiswillhelptoavoidanycrackinginthegel-coatlayerwhenthescrewsaretightened.4. Removethebail-mountbrackettemplatefromthemountingsurface.5. Securethebailmounttothesurfaceusingthefourincluded35mmM4.2×1.4screws. NotE: Stainless-steel screws may bind when screwed into fiberglass and overtightened. Garmin recommends applying an anti-galling,
stainlessanti-seizelubricanttothescrewbeforeusing.
to install the GPSMAP 700 series chartplotter on the bail-mount bracket:1. LooselyattachthemountingknobstotheGPSMAP700serieschartplotter.2. Slidethechartplotterontothebailmount,andtightenthemountingknobs.
Flush Mounting the ChartplotterHardware (included):• Flush-mounttemplate• Four35mmM4.2× 1.4screws
tools required (not included):• Jigsaw• Drillanddrillbits—3/8in.(9.5mm)and1/8in.(3mm)• Number2Phillipsscrewdriver• Centerpunchandhammer• Fileandsandpaper
To flush mount a GPSMAP 700 series chartplotter:1. The flush-mount template is included in the product box. Trim the template and ensure it will fit in the location where you want to flush mount
thechartplotter. NotES:
Make sure the surface on which you mount the chartplotter has adequate open space behind it to fit the chartplotter and the connected cables,andmakesuretoleaveapproximately1/2in.(13mm)ofspaceontherightsideofthechartplottertoaccesstheSDcarddoorandsuncover.Toavoidinterference,mountaGPSMAP700serieschartplotteratleast32in.(813mm)fromamagneticcompass.
2. The flush-mount template has adhesive on the back. Remove the protective liner and apply the template to the location at which you want to mountthechartplotter.
3. Usinga3/8in.(9.5mm)drillbit,drillapilotholeinsidethecornerofthetemplatetobegincuttingthemountingsurface.4. Using the jigsaw, cut the mounting surface along the inside of the solid line indicated on the flush-mount template. Use a file and sandpaper
to refine the size of the hole.5. Ifthetopandbottommountingcoversareattachedtothefrontofthechartplotter,removethembyunsnappingthecoversfromthesides.6. Place the chartplotter in the hole, and make sure that the mounting holes on the chartplotter line up with the pilot holes on the flush-mount
template after cutting, sanding, and filing the hole. If they do not line up, mark the locations where the pilot holes need to be.7. Usingthecenterpunch,indentthecenterofeachofthemounting-holelocations.8. Usinga1/8in.(3mm)drillbit,drillthepilotholes. NotE: If you are mounting the chartplotter in fiberglass, it is recommended to use a countersink bit to drill a clearance-counter bore through
onlythetopgel-coatlayer.Thiswillhelptoavoidanycrackinginthegel-coatlayerwhenthescrewsaretightened.9. Placethechartplotterintothecutout.10.Securelytightenthefourincluded35mmM4.2×1.4mountingscrewsthroughthechartplotterintothepilotholes. NotE: Stainless-steel screws may bind when screwed into fiberglass and overtightened. Garmin recommends applying an anti-galling,
stainlessanti-seizelubricanttothescrewbeforeusing.11.Installthetopandbottommountingcoversbysnappingthemintoplace.
•
•
� GPSMAP 700 Series Installation Instructions
Installing the Power/Data CableThe chartplotter comes with a power/data cable that connects the chartplotter to power and to optional NMEA 0183 devices. If applicable, the power/data cable also connects the chartplotter to a sonar transducer. The power/data cable does not connect the chartplotter to a NMEA 2000 network. For instructions on connecting the chartplotter to a NMEA 2000 network, see page 6.
To help make the cable-routing process easier, the locking ring is packaged separately from the cable. If you install the power/data cable through the bail mount, do not install the locking ring until after all the cables are routed.
Installing a locking ring on the cable:1. Routethecableawayfromsourcesofelectronicinterferencesothatthecableconnectorisatthe
mountinglocationofthechartplotter.2. Separatethetwohalvesofthelockingring.3. Alignthetwohalvesofthelockingringoverthecableandsnapthemtogether.4. InserttheO-ringintotheendoftheconnector.
GPSMAP 700 Series Power/Data Cable
>
>
>
>
To transducer (if applicable)
Red
Black
Accessory on
Blue
Spare
Spare
Alarm low
Wire Color Wire Function
Power (10–�� Vdc)Ground
(power and NMEA 018�)
NMEA 018� port 1 Tx (out)
Brown
Gray
Violet
Green
White
Orange
Yellow
To the GPSMAP 700 series chartplotter
Fuse
� A
NMEA 018� port 1 Rx (in)
NMEA 018� port � Tx (out)
NMEA 018� port � Rx (in)
Notes: UseanAGC/3AG-3Ampreplacementfuse.Ifitisnecessarytoextendthepowerandgroundwires,use16AWGwire.Youcanwirethecabledirectlytothebattery,orifyourboathasanelectricalsystem,youmightbeabletowirethecabletoanunusedholderonthefuseblock.Ifyouusetheboatfuseblock,removethein-linefuseholderonthepowerwireofthecable.Donotcutthetransducercable,becausethisvoidsyourwarranty.
Notice The maximum input voltage is 32 Vdc. Do not exceed this voltage because this can damage the chartplotter and void the warranty.
NOTE: If you are not connecting the chartplotter to NMEA 0183 devices, use only the red and black wires. The other wires do not have to be connected for normal operation of the chartplotter. For information on connecting to a NMEA 0183-compatible device, see page 5.
•••
•
Installing the Locking RingInstalling the Locking Ring
GPSMAP 700 Series Installation Instructions �
Connecting the Power/Data Cable to Power1. Useatestlightoravoltmetertodeterminethepolarityofthevoltagesource.2. Connectthered(+orpositive)wiretothepositivevoltageterminal.(Ifyouusethe
fuseblockontheboat,routethepositiveconnectionthroughthefuse,asshownonthediagram.)
3. Connecttheblack(-orground)wiretothenegativevoltageterminal.4. Installorcheckthe3Afuse(inthein-linefuseholder,oronthefuseblockoftheboat).
Connecting the Power/Data cable to a NMEA 0183 Device (optional)You can connect the GPSMAP 700 series chartplotter to other NMEA 0183-compatible equipment, such as a DSC or AIS device. Refer to the wiring diagram for connecting the chartplotter to NMEA 0183-compatible devices.
Wiring a GPSMAP 700 Series Chartplotter to a Standard NMEA 0183 Device
+ -
>>
>
>
Red (power)Black (ground)
Brown (in)
Blue (out)
Wire color
PowerPower groundNMEA GroundNMEA Rx/A (+)NMEA Tx/A (+)
NMEA 018�-compatible device
GPSMAP 700 series
chartplotter
Battery10–�� Vdc
Fuse� A
Wire function
to connect the power/data cable to a NMEA 0183 device:1. ForGarmindevices,theground(black)wiresserveasNMEA0183groundandmustbeattachedtogetheroronthesameterminalasthe
NMEA 0183 ground on your NMEA 0183 device. Refer to the wiring diagram of your NMEA 0183 device for wire identification.2. Connecttheblue(NMEA0183port1out)wirefromtheGPSMAP700power/datacabletotheNMEA0183in(orRx/A+)wirefromthe
NMEA0183device,andthebrown(NMEA0183port1in)wiretotheNMEAout(orTx/A+)wirefromtheNMEA0183device.3. Repeatstep2usingthegray(NMEA0183port2out)andviolet(NMEA0183port2in)wiresforanadditionalNMEA0183device.4. Settheserialport(orports)onthechartplottertouseNMEA0183data(standardorhigh-speed).SeetheGPSMAP 700 Series Owner’s
Manualformoreinformation.
Connecting the Power/Data Cable to a Lamp or to a Horn (optional)The GPSMAP 700 series chartplotter can be used with a lamp, a horn, or both, to sound or flash an alert when the chartplotter displays a message. The alarm does not need to be wired for the chartplotter to function. The alarm circuit switches to a low-voltage state when the alarm sounds. The maximum current is 100 mA, and a relay is needed to limit the current from the chartplotter to 100 mA. To manually toggle visual and audible alerts, install single-pole, single-throw switches.
Wiring to a Lamp, a Horn, or Both
+ -
GPSMAP 700 series chartplotter
Wire Color
Red (power)Black (gnd)
Yellow (alarm)
Battery 10–�� Vdc
Relay 100 ma max coil current
Horn
Lamp
Fuse� A
Fuse Block Example
—
+
2A3A
-
+Boat ground
� A fuseTo 10–�� Vdc boat supply
To deviceFuse Block Example
—
+
2A3A
-
+Boat ground
� A fuseTo 10–�� Vdc boat supply
To device
� GPSMAP 700 Series Installation Instructions
Connecting the Chartplotter to a NMEA 2000 Network (optional)You can connect the GPSMAP 700 series chartplotter to your existing NMEA 2000 network. You will need the appropriate NMEA 2000 cables and connectors, either to connect the chartplotter to your existing NMEA 2000 network or to build a NMEA 2000 network if you do not have one installed on your boat. Contact your local Garmin dealer.
If you are unfamiliar with NMEA 2000, read the “NMEA 2000 Network Fundamentals” chapter of the Technical Reference for Garmin NMEA 2000 Products. The document is located on the included CD and on the NMEA 2000 section of the Garmin Web site at http://www.garmin.com/garmin/cms/us/onthewater/nmea2000.
Connecting the Chartplotter to a Garmin Marine Radar (optional)You can connect the GPSMAP 700 series chartplotter to a Garmin marine radar such as a GMR™ 18 HD (not included).
to connect the chartplotter to a Garmin marine radar:1. Installtheradaraccordingtotheinstallationinstructionsprovidedwiththeradar.2. RoutetheGarminmarinenetworkcabletothechartplotter,andconnectittotheradarport. NotE:TheGPSMAP700serieschartplotteriscompatiblewithaGarminmarineradar,butitisnotcompatiblewiththeGarminmarine
network.DonotconnectotherGarminmarinenetworkdevicestotheradarportontheGPSMAP700serieschartplotter.3. Updatethechartplottersoftware(page7).
Connecting the Chartplotter to a GA 30 Remote GPS Antenna (optional)The GPSMAP 700 series chartplotter has an internal GPS receiver, but some installations, such as a flush-mount-installation, may not allow a view of the sky that the device needs to calculate your GPS position. You can install a GA 30 remote GPS antenna (not included) in an appropriate location and connect it to the chartplotter to provide GPS information.
to connect the chartplotter to a GA 30 antenna:1. InstalltheGA30antennaaccordingtotheinstructionsprovidedwiththeantenna.2. RoutetheGA30cabletothechartplotter,andconnectittotheexternalGPSantennaconnector.
Connecting the Chartplotter to a transducerIf you have a sonar-cable GPSMAP 700 series chartplotter (indicated by an “s” in the product name), you can connect a Garmin transducer to use sonar-specific features.
to connect the chartplotter to a transducer:1. Installthetransduceraccordingtotheinstructionsprovidedwiththetransducer.2. Routethetransducercabletothechartplotterandconnectittothepower/datacable.
GPSMAP 700 Series Installation Instructions 7
IdentifyingtheRear-PanelConnectorsAfter the power/data cable is wired to the boat (and after any optional Garmin radar, NMEA 0183, NMEA 2000, or external GPS devices are installed) connect the cables to the GPSMAP 700 series chartplotter.
NOTE: You must install the locking rings before connecting the power/data cable or a Garmin radar cable to the chartplotter (page 4).
to connect a cable to the back of a GPSMAP 700 series chartplotter:1. Carefully press the cable into the correct port on the back of the chartplotter until it is firmly seated. Do not force the cable, because this
may damage the pins.2. Afterthecableisseated,turnthelockingringclockwiseuntilitistight.Becarefulnottoovertightenthelockingring.
➊ ➋ ➌ ➍
GPSMAP 700 Series Connectors
➊ NMEA 2000 connector
➋ Radar port
➌ Power/data connector
➍ External GPS antenna connector
updating the Chartplotter SoftwareThe GPSMAP 700 series chartplotter may contain a software update SD card. If so, follow the instructions provided with the card.
If a software update SD card is not included, visit www.garmin.com to make sure your chartplotter software is up-to-date. To identify the version of software on your chartplotter, select or touch Configure > System > System Information.
8 GPSMAP 700 Series Installation Instructions
Appendix
SpecificationsPhysical SpecificationsSpecification MeasurementSize W × H × D: 8 29/32×519/32×31/8in.(226×142×80mm)Weight 2.48lb.(1.125kg)Display W × H: 6 × 3 19/32in.(152×91mm)Case FullyGasketed,high-impactplasticandaluminumalloy,waterprooftoIEC60529IPX-7Temp.Range From5°Fto131°F(from-15°Cto55°C)CompassSafeDistance
32in.(813mm)
GPS PerformanceSpecification Parameter MeasurementReceiver High-sensitivity12parallelchannel,WAAS-capablereceiverAcquisitionTime
Warm Approximately1sec.(Thedeviceisatornearthelastlocationatwhichyourecentlyacquiredsatellites.)Cold Approximately38sec.(Thedevicehasmovedmorethanabout500mi.[800km]sinceitwasturnedoff.)Reacquisition <1sec.
UpdateRate 1/sec.,continuousAccuracy GPS <33ft.(10m)95%typical
DGPS 10–16ft.(3–5m)95%typical(WAAS/EGNOSaccuracy)Velocity 0.05m/sec.steadystate
PowerSpecification MeasurementSource 10–32VdcUsage 8.56Wmax.at13.8VdcFuse 3ANMEA2000LoadEquivalencyNumber(LEN) 2NMEA2000Draw 100mAmaximum
SonarPower 1kWTransducer,1,000W(RMS),8,000W(peaktopeak);DualFrequency,500W(RMS),4,000W(peaktopeak);DualBeam,400W
(RMS),3,200W(peaktopeak)Frequency 50/200kHz(dualfrequencyand1kW),80/200kHz(dualbeam)Depth 2,500ft.(762m)(1kW),1,500ft(457m)(dualfrequency),900ft(274m)(dualbeam)-Depthcapacityisdependentonwatersalinity,bottom
type,andotherwaterconditions.
NMEA 2000 PGN InformationReceive transmit
059392 ISOAcknowledgment 059392 ISOAcknowledgment059904 ISORequest 059904 ISORequest060928 ISOAddressClaim 060928 ISOAddressClaim126208 NMEA-Command/Request/AcknowledgeGroupFunction 126208 NMEA-Command/Request/AcknowledgeGroupFunction126464 Transmit/ReceivePGNListGroupFunction 126464 Transmit/ReceivePGNListGroupFunction126996 ProductInformation 126996 ProductInformation127245 Rudder 127250 VesselHeading127250 VesselHeading 127258 MagneticVariance127488 EngineParameters-RapidUpdate 128259 Speed-WaterReferenced127489 EngineParameters-Dynamic 128267 WaterDepth127493 TransmissionParameters-Dynamic 129025 Position,RapidUpdate127498 EngineParameters-Static 129026 COG/SOGRapidUpdate127505 FluidLevel 129029 GNSS-PositionData
GPSMAP 700 Series Installation Instructions �
Receive transmit
128259 Speed-WaterReferenced 129283 CrossTrackError128267 WaterDepth 129284 NavigationData129038 AISClassAPositionReport 129285 Navigation-Route/WPinformation129039 AISClassBPositionReport 129539 GNSSDOPs129040 AISClassBExtendedPositionReport 129540 GNSSSatsinView129794 AISClassAStaticandVoyageRelatedData 130306 WindData129798 AISSARAircraftpositionreport129799 RadioFrequency/Mode/Power129802 AISSafetyRelatedBroadcastMessage129808 DSCCallInformation
130306 WindData GPSMAP700serieschartplottersareNMEA2000certified.130576 SmallCraftStatus
130310 EnvironmentalParameters
130311 EnvironmentalParameters(Obsolete)130312 Temperature130313 Humidity130314 ActualPressure
NMEA 0183 InformationNMEA 0183, Version 3.01 Sentences:Receive transmitDPT Depth GPAPB APB-Heading/TrackController(Autopilot)Sentence"B"DBT DepthBelowTransducer GPBOD BOD-Bearing-OrigintoDestinationMTW WaterTemperature GPBWC BWC-Bearing&DistancetoWaypointVHW WaterSpeedandHeading GPGGA GGA-GlobalPositioningSystemFixDataWPL WaypointLocation GPGLL GLL-GeographicPosition-Latitude/LongitudeVDM AISVHFData-LinkMessage GPGSA GSA-GNSSDOPandActiveSatellitesDSC DigitalSelectiveCallingInformation GPGSV GSV-GNSSSatellitesinViewDSE ExpandedDigitalSelectiveCalling GPRMB RMB-RecommendedMinimumNavigationInformationHDG Heading,Deviation&Variation GPRMC RMC - Recommended Minimum Specific GNSS DataHDM Heading,Magnetic GPRTE RTE-RoutesMWD WindDirection&Speed GPVTG VTG-CourseOverGroundandGroundSpeedMDA MeteorologicalComposite GPWPL WPL-WaypointLocationMWV WindSpeedandAngle GPXTE XTE-CrossTrackErrorVDM AISVHFData-LinkMessage PGRME E-Estimatederror
PGRMM M-MapdatumPGRMZ Z-AltitudeSDDBT DBT-DepthBelowTransducerSDDPT DPT-DepthSDMTW MTW-WaterTemperatureSDVHW VHW-WaterSpeedandHeading
You can purchase complete information about National Marine Electronics Association (NMEA) format and sentences from: NMEA Seven Riggs Avenue Severna Park, MD 21146 USA www.nmea.org
Garmin®, the Garmin logo, GPSMAP®, and AutoLocate® are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. GMR™ is a trademark of Garmin Ltd. or its subsidiaries. These trademarks may not be used without the express permission of Garmin. NMEA 2000® and the NMEA 2000 logo are registered trademarks of the National Marine Electronics Association.
For the latest free software updates (excluding map data) throughout the life of your Garmin products, visit the Garmin Web site at www.garmin.com.
©2010GarminLtd.oritssubsidiaries
GarminInternational,Inc.1200East151stStreet,Olathe,Kansas66062,USA
Garmin(Europe)Ltd.LibertyHouse,HounsdownBusinessPark,Southampton,Hampshire,SO409LRUK
GarminCorporationNo.68,Jangshu2ndRoad,Sijhih,TaipeiCounty,Taiwan
www.garmin.com
February2010 PartNumber190-01155-02Rev.B PrintedinTaiwan