1

GN012 Application Note

May 25, 2020GaN Systems Inc.

Gate Driver Circuit Design with GaN E-HEMTs

2

Gate Bias Level GaN Systems GaN E-HEMT Si MOSFET IGBT SIC MOSFET

Maximum rating -20/+10V -/+20V -/+20V -8/+20V

Typical gate bias values 0 or-3/+5-6V 0/+10-12V 0 or -9/+15V -4/+15-20V

Common with Si MOSFET True enhancement-mode normally off Voltage driven - driver charges/discharges CISS Supply Gate leakage IGSS only Easy slew rate control by RG Compatible with Si gate driver chip

Differences Much Lower QG : Lower drive loss; faster switching Higher gain and lower VGS : +5-6V gate bias to turn on Lower VG(th): typ. 1.5V

Versus other enhancement-mode GaN More robust gate: -20/+10V max rating No DC gate drive current required No complicated gate diode / PN junction

CISS = CGD+CGS

Simple-driven GaN Technology

GaN HEMTs are simple to drive

3

650V Drivers• GaN Systems GaN HEMTs are compatible with most drivers for silicon devices. • When the driver supply voltage(VDD) is higher than +6V (the recommended turn-on VGS for GaN), a negative

VGS generating circuit is required to convert the VGS into +6/-(VDD-6) V, refer to page 7. • VDD is recommended to ≤12V.

Most popular solutions:

Gate Drivers Configuration Isolation Notes

Si8271 Single switch Isolated Split outputs

Si8273/4/5 Half-Bridge Isolated Dead time programmability

ADuM4121ARIZ Single Switch Isolated Internal miller clamp

ACPL-P346 Single Switch Isolated Internal miller clamp

HEY1011 Single Switch Isolated Power Rail Integrated

NCP51820 Half Bridge Non-Isolated Bootstrap voltage management

4

Gate Drivers Configuration Split OutputsBootstrap voltage

management Notes

PE29101 Half-Bridge Yes Yes Frequency up to 33MHz

PE29102 Half-Bridge Yes No Frequency up to 33MHz

uP1966A Half-Bridge Yes Yes General Purpose

LMG1205 Half-Bridge Yes Yes General Purpose

LM5113-Q1 Half-Bridge Yes Yes Automotive Qualified

100V/80V Drivers• GaN Systems GaN HEMTs are compatible with most of the drivers for silicon devices. • When the driver supply voltage(VDD) is higher than +6V (the recommended turn-on VGS for GaN), a negative

VGS generating circuit is required to converter the VGS into +6/-(VDD-6) V, refer to page 7. • VDD is recommended to ≤12V.

Most popular solutions:

5

• GaN Systems GaN HEMTs are compatible with most of the controllers for silicon devices. • When the driver supply voltage(VDD) is higher than +6V (the recommended turn-on VGS for GaN), a negative

VGS generating circuit is required to converter the VGS into +6/-(VDD-6) V, refer to page 7. • VDD is recommended to ≤12V.

Most popular solutions:

Configurations Controllers Description

Flyback- Adapters- Chargers- Other low-power

AC/DCs

NCP1342 650V, Quasi-resonant

UCC28600 600V, Quasi-resonant

NCP1250 650V, Fixed frequency

Sync Buck DC/DC(48V/12V) LTC7800 60V, Sync rectifier control, up to 2.2MHz

Controllers with Driver Integrated for GaN

6

Controllers with Driver Integrated for GaN - continued

Configurations Controllers Notes

LLC- Adapters - Chargers- Flat panel

displays- Industrial power

NCP13992 600V, current mode controller

NCP1399 600V, current mode controller, off-mode operation

UCC256404 600V, optimized burst mode, low audible noise and standby power

UCC256301 600V, hybrid hysteric mode, low standby power, wide operating frequency

PFC- PC Power

Supplies- Appliances- LED Drivers

NCP1615 / NCP1616 700V, critical conduction mode operation

UCC28180 Programable frequency, continuous conduction mode operation, no AC line HV sensing

PFC + LLC HR1203 700V, CCM/DCM Multi-mode PFC control, adjustable dead-time and bust mode switching LLC

• GaN Systems GaN HEMTs are compatible with most of the controllers for silicon devices. • When the driver supply voltage(VDD) is higher than +6V (the recommended turn-on VGS for GaN), a negative

VGS generating circuit is required to converter the VGS into +6/-(VDD-6) V, refer to page 7. • VDD is recommended to ≤12V.

Most popular solutions:

7

Driver Circuit Examples

Single switch driver

Isolated

0V VGS(OFF) Single Isolated Driver

Negative VGS(OFF)

EZDrive®

With voltage divider

Digital Isolator + Non-isolated Driver

Non-Isolated0V VGS(OFF)

Negative VGS(OFF) EZDrive®

Half/Full Bridge driver

Isolated Implement two single switch drivers

Non-Isolated0V VGS(OFF) Bootstrap driver

Negative VGS(OFF) Bootstrap driver + EZDrive®

Paralleling GaN Driver Circuit for GaN HEMT in Parallel

* When is negative VGS(OFF) needed?

8

Single GaN Isolated 0V VGS(OFF) Single Isolated Driver

+VIN

GND NC

+VO

0V1

2

4

5

8

PWM

VCC+5V

DRAIN

SOURCE

GATE

9V ISO DC-DCVCC

10u 4.7u 4.7u

0.1u

1u

2.2u

100

10

2 10k

2VI

GNDI

EN

VDD

VO+

GND

3

1

SI8271GB-IS

6

5

8

4

7VDDI

VO-

VDD_6V

CM

0.1u

22p

GNDON/OFFIN OUT

BYP

13

2 4

5

LP2985AIM5-6.1/NOPB

VDD_6V

+9VISO

3.3k

+VIN

GND NC

+VO

0V1

2

4

5

8

IN+

VCC5V DRAIN

SOURCE

GATE

9V ISO DC-DCVCC

10u 4.7u 4.7u

1u

2.2u

100 10

0 10k

VDD6V

CM

GNDON/OFFIN OUT

BYP

13

2 4

5

LP2985AIM5-6.1/NOPB

VDD6V

+9VISO

2VDD1

VIN-

GND1

VDD2

VOUT

GND2

3

1

ADUM4121ARZ

6

5

8

4

7VIN+

CLAMP100

IN-

0

0.1u

< BACK

• 0V VGS(OFF) for low voltage or low power applications, or where the deadtime loss is critical• Optional CM Choke for better noise immunity

Example I: Driver with separate outputs for switch ON/OFF (SI8271) Example II: Driver with single output for switch ON and OFF (ADUM4121)

9

+VIN

GND NC

+VO

0V1

2

4

5

8

PWM

VCC+5V

DRAIN

SOURCE

GATE

9V ISO DC-DCVCC

10u 4.7u 4.7u

0.1u

1u

100

10

2 10k

2VI

GNDI

EN

VDD

VO+

GND

3

1

SI8271AB-IS

6

5

8

4

7VDDI

VO-

CM

0.1u

22p

3.3k

+9V

+9V

10k

47n5.6V

5.6V

< BACK

Single GaN Isolated Negative VGS(OFF) EZDrive®

• Negative VGS voltage is applied by the 47nF capacitor• Compatible with bootstrap circuit• Applicable from 1kW ~ 100kW power range• Optional CM Choke for better noise immunity

Example: SI8271 EZDrive® circuit (VGS=+6V/-3V)

For more info about GaN EZDrive®, please refer to GN010: https://gansystems.com/

http://www.gansystems.com/gs61004b-evbcd.php

10

+VIN

GND NC

+VO

0V1

2

4

5

8

PWM

VCC+5V

VDD

VEE

DRAIN

SOURCE

GATE

9V ISO DC-DCVCC

10u 4.7u 4.7u

0.1u

1u

1u

100

10

2 10k

2VI

GNDI

EN

VDD

VO+

GND

3

1

SI8271AB-IS

6

5

8

4

7VDDI

VO-

2.2k1k 1u

1u5.8V

VEE

VDD

CM

0.1u

22p

3.3k

< BACK

Single GaN Isolated Negative VGS(OFF) with Voltage divider

• Negative VGS voltage is generated by the voltage divider (5.8V Zener diode and 1kOhm resistor)• Robust and easy to layout• Applicable for applications from low power to higher power (1kW ~ 100kW)• Optional CM Choke for better noise immunity

Example: SI8271 driving circuit with voltage divider (VGS=+6V/-3V)

11

Single GaN Isolated Negative VGS(OFF) Digital Isolator + Non-isolated Driver

< BACK

• To enable non-isolated driver or buffer with high sink current capability where isolation is required • For high power applications: e.g. EV motor drive, PV inverter, etc• Optional CM Choke for better noise immunity

Example: SI8610 (digital isolator) + UCC27511(Non-isolated driver) (VGS=+6V/-6V)

INHIB

IN OUT

GND

1

3 2

5

LD2980ABM50TR

+VIN

GND NC

+VO

0V1

2

4

5

8

2VDD1

NC

GND1

VDD2

NC

GND2

3

1

SI8610BC-B-IS

6

5

8

4

7PWM

VCC+5V 5VISO

5VISO

+6VVDD

10u 4.7u 4.7u1u

0.1u 0.1u

100100

12V ISO DC-DCCM

+6V

DRAIN

SOURCE

GATE1

10 10k

5GND

IN-

IN+

OUTL

OUTH

VDD 16

4 3

2

UCC27511DBVR

2.2k1k 1u

1u6V

-6V

-6V

-6V

-6V

http://www.gansystems.com/gs61004b-evbcd.php

12

GNDON/OFFIN OUT

BYP

13

2 4

5

LP2985AIM5-6.1/NOPB

PWM

VDD +6V

+6V

DRAIN

SOURCE

GATE

10

1

10 10k

1u

2.2u4.7u

5GND

IN-

IN+

OUTL

OUTH

VDD 16

4 3

2

UCC27511DBVR

< BACK

Single GaN Non-Isolated 0V VGS(OFF)

• For single-ended applications (Class E, Flyback, Push-pull etc)• Or to work with a digital isolator for the high-side switch

Example: UCC27511 driving circuit (VGS=+6V/0V)

http://www.gansystems.com/gs61004b-evbcd.php

13

PWM

VDD +9V

+9V

DRAIN

SOURCE

GATE

10

1

10 10k

1u

2.2u2.2u

5GND

IN-

IN+

OUTL

OUTH

VDD 16

4 3

2

UCC27511DBVR

VIN VOUT

GND

UA78L09AC

10k

47n5.6V

5.6V

< BACK

Single GaN Non-Isolated Negative VGS(OFF) EZDrive®

• Negative VGS voltage is applied by the 47nF capacitor• Compatible with bootstrap circuit• Optional CM Choke for better noise immunity

Example: UCC27511 driving circuit (VGS=+6V/-3V))

For more info about GaN EZDrive®, please refer to GN010: https://gansystems.com/

http://www.gansystems.com/gs61004b-evbcd.php

14< BACK

Half/Full Bridge 0V VGS(OFF) Bootstrap

• For low power applications• Choose the bootstrap diode with low CJ and fast recovery time

Example: NCP51820 Bootstrap driving circuit (VGS=+6V/0V)

15< BACK

Half/Full Bridge Negative VGS(OFF) Bootstrap + EZDrive®

• EZDrive® can get a negative voltage on 47nF capacitor, which can be used as turn off voltage• Turn on/off slew rate is controllable with external resistors to optimize EMI• Suitable for low power application

Example: NCP51530 Bootstrap driving circuit with EZdrive® (VGS=+6V/-3V)

For more info about GaN EZDrive®, please refer to GN010: https://gansystems.com/

16

GNDON/OFFIN OUT

BYP

13

2 4

5

LP2985AIM5-6.1/NOPB

PWM

VDD +6V

+6V

10

1

1010k

1u

2.2u4.7u

5GND

IN-

IN+

OUTL

OUTH

VDD 16

4 3

2

UCC27511DBVR

DRAIN

SOURCE

1 1

11

GATE GATE

7

HB

HOH

HS6

LM5113

HOL

3

4

2

5

10

9

1

LOL

LOH

VDD

VSS

HI

LI

8

10

10

1

1

VIN

100k

100k

G

G

D

D

S

S

1u

6V

PWM1HPWM1L

1u

1u

GND

11

11

1

11

1

G

D

D

S

S

G

< BACK

Driver Circuit for GaN HEMT in Parallel

• For HEMTs in parallel, add additional 1ohm gate and source resistors (as highlighted below)

For more info about GaN in parallel, please refer to GN004: https://gansystems.com/

Example: UCC27511 non-isolated driving circuit for single GaN (VGS=+6V/0V) Example: LM5113 bootstrap driving circuit for half-bridge (VGS=+6V/0V)

17

Appendix

Gate driving tips for VGS(OFF) When is VGS(OFF) needed?

VGS(OFF) vs. Switching-off Loss

Trade-off between Switching-off Loss and Deadtime Loss

18

When is negative VGS(OFF) needed?

Negative VGS(OFF) can increase noise immunity

Negative VGS(OFF) can reduce switching-off loss especially under high-current

Deadtime loss increases as Negative VGS(OFF) increase (more info please refer to page 8, APPNOTE GN001)

There is a tradeoff between switching-off and deadtime loss for VGS(OFF) selection. -3V VGS(OFF) is recommended to start with for above 0.5kW applications.

< BACK

19

VGS(OFF) vs. Switching-off Loss

Switching-off loss of GS66516B vs. current at VBUS=400 V, 25℃, RG=1Ω

Negative VDRoff reduces the switching off energy under high current.

20

VGS(OFF) vs. Zero Voltage Switching Boundary and Dead Time Loss

Relation between total loss and deadtime of GS66516B at ID=10A, 25 ℃

Optimum deadtime Vs. switching off current at VBUS=400V

0.5 � 𝐿𝐿 � 𝑖𝑖𝑆𝑆𝑆𝑆𝑆𝑆𝑆𝑆2> 𝑖𝑖𝑆𝑆𝑆𝑆𝑆𝑆𝑆𝑆 � 𝑉𝑉𝑆𝑆𝑆𝑆 � (td−𝐶𝐶𝑒𝑒𝑒𝑒�𝑉𝑉𝐷𝐷𝐷𝐷𝑆𝑆𝑆𝑆𝑆𝑆𝑆𝑆𝑆𝑆

) + 0.5 � 𝐶𝐶𝑒𝑒𝑒𝑒 � 𝑉𝑉𝑆𝑆𝐶𝐶2 (2) 𝑡𝑡𝑑𝑑 > 𝐶𝐶𝑒𝑒𝑒𝑒�𝑉𝑉𝑏𝑏𝑏𝑏𝑏𝑏𝑆𝑆𝑆𝑆𝑆𝑆𝑆𝑆𝑆𝑆𝑆𝑆𝑆𝑆𝑆𝑆𝑆𝑆𝑆

(1)ZVS boundary:

• Deadtime loss increases as VGS(OFF) increases• A too short dead time will result in losing ZVS, while a too long dead time will cause additional loss

21

Trade-off between Switching-off Loss and Deadtime Loss

Half-bridge overall loss vs. switching current under different negative turn-off gate voltage VDRoff(a) with deadtime tD=40 nS, (b) with deadtime tD=100 nS, (c) with deadtime tD=200 nS.

• Negative VDRoff is will make the power stage more efficient under higher power. • Precise dead time control is the key to higher system efficiency.

GN012 Application Note �Simple-driven GaN Technology650V Drivers100V/80V DriversControllers with Driver Integrated for GaNControllers with Driver Integrated for GaN - continuedDriver Circuit ExamplesSingle GaN Isolated 0V VGS(OFF) Single Isolated DriverSingle GaN Isolated Negative VGS(OFF) EZDrive®Single GaN Isolated Negative VGS(OFF) with Voltage dividerSingle GaN Isolated Negative VGS(OFF) Digital Isolator + Non-isolated DriverSingle GaN Non-Isolated 0V VGS(OFF) Single GaN Non-Isolated Negative VGS(OFF) EZDrive®Half/Full Bridge 0V VGS(OFF) BootstrapHalf/Full Bridge Negative VGS(OFF) Bootstrap + EZDrive®Driver Circuit for GaN HEMT in ParallelAppendixSlide Number 18Slide Number 19VGS(OFF) vs. Zero Voltage Switching Boundary and Dead Time LossTrade-off between Switching-off Loss and Deadtime Loss