gloss finish for wood andcork - Rustins Corporate brands of dye mayf not be compatible. The...
1
STIR WELL BEFORE USE. IF NOT STIRRED UNTIL THERE IS NO SEDIMENT AT THE BOTTOM OF THE TIN. Rustins Polyurethane Floor Sealer is a high solid air drying Polyurethane. For use on clean, bare wood, hardboard, MDF and unsealed cork. Three coats are recommended on wood and four on cork floors. It is essential that the floor is thoroughly clean and free from wax and grease. If a floor has previously been waxed, it is advisable to clean the wax off the floor, even if it is to be sanded, otherwise wax can be left on the sanding belt and traces left on the sanded floor. This would then prevent the Polyurethane from drying properly. Wax polish can be removed by rubbing in the direction of the grain with grade 3 or 4 steel wool and White Spirit, wiping off the solution of wax formed with clean rag. If the floor is to be sanded, ensure that all nail heads are punched below the surface before sanding. Nail holes and cracks can be filled with Rustins Wood Filler. Existing varnish not being removed should be clean and lightly sanded to provide a key. Bare wood or old floors that have been sanded may be stained with Rustins Wood Dye before coating. Other brands of dye may not be compatible. The Polyurethane Floor Sealer should be applied liberally with the biggest brush available, or with a roller. The drying time is between 4-6 hours, according to temperature. This tin will cover approximately 35 square metres one coat, depending on porosity of the surface. Brushes and rollers can be cleaned after use with White Spirit or Rustins Brush Restorer. White Spirit may also be used to thin the Polyurethane Floor Sealer, if required. The sealer may also be used on old concrete to prevent dusting. HEALTH AND SAFETY Flammable liquid and vapour. Contains cobalt octoate, methyl ethyl ketoxime. May produce an allergic reaction. Repeated exposure may cause skin dryness or cracking. Take precautionary measures against static discharge. Wear eye protection. IF ON SKIN (or hair): Remove immediately all contaminated clothing. Rinse skin with water. In case of fire: Use carbon dioxide for extinction. Store in a well-ventilated place. Keep cool. Dispose of contents/container to hazardous or special waste collection point. gloss finish for wood and cork Clear gloss finish for wood and cork Clear IMPORTANT Factory pre-sealed cork floor tiles may be wax coated which will affect the drying of Rustin’s Polyurethane Floor Sealer. Test on a spare tile or a small area of the floor. If the coating still remains tacky after eight to ten hours the floor should be dewaxed with White Spirit and steel wool, wiping whilst still damp with clean rag. World’s finest range of products for the professional & home handyman For information on Rustins’ products visit our website at www.rustins.co.uk or contact us at Rustins Ltd, Waterloo Road, London, NW2 7TX United Kingdom [email protected] Telephone: +44 (0)20 8450 4666 Rustins’ range includes: Acrylic Varnishes Aluminium Paints Bitumen Black Black Matt Paint Blackboard Black Brick & Tile Paint Clear Metal Lacquer for Brass & Copper Danish Oil French Polishes Gold Paint Grainfiller Knotting Paint, Gloss & Undercoat Polyurethane Varnishes Primers Quick Drying Coloured Varnishes Radiator Paint Rust Remover Strypit Paint & Varnish Stripper Teak Oil Wallpaper Remover Wood Dyes Woodstopping Yacht Varnish Contents will cover approximately 35 sq. metres (375 sq. ft.) one coat 2 1 / 2 litres Made in UK EU Limit value for this product (CAT A/i): 500g/l (2010) This product contains max 460 g/l VOC WARNING
Transcript of gloss finish for wood andcork - Rustins Corporate brands of dye mayf not be compatible. The...
STIR WELL BEFORE USE. IF NOT STIRRED UNTIL THERE IS NO SEDIMENT AT THEBOTTOM OF THE TIN.Rustins Polyurethane Floor Sealer is a high solid air drying Polyurethane. For use onclean, bare wood, hardboard, MDF and unsealed cork. Three coats are recommended onwood and four on cork floors. It is essential that the floor is thoroughly clean and freefrom wax and grease. If a floor has previously been waxed, it is advisable to clean thewax off the floor, even if it is to be sanded, otherwise wax can be left on the sanding beltand traces left on the sanded floor. This would then prevent the Polyurethane from dryingproperly. Wax polish can be removed by rubbing in the direction of the grain with grade 3or 4 steel wool and White Spirit, wiping off the solution of wax formed with clean rag. Ifthe floor is to be sanded, ensure that all nail heads are punched below the surface beforesanding. Nail holes and cracks can be filled with Rustins Wood Filler. Existing varnish not being removed should be clean and lightly sanded to provide a key.Bare wood or old floors that have been sanded may be stained with Rustins Wood Dyebefore coating. Other brands of dye may not be compatible.The Polyurethane Floor Sealer should be applied liberally with the biggest brushavailable, or with a roller. The drying time is between 4-6 hours, according totemperature.This tin will cover approximately 35 square metres one coat, depending on porosity of the surface.Brushes and rollers can be cleaned after use with White Spirit or Rustins Brush Restorer.White Spirit may also be used to thin the Polyurethane Floor Sealer, if required. The sealer may also be used on old concrete to prevent dusting.
HEALTH AND SAFETYFlammable liquid and vapour.Contains cobalt octoate, methyl ethyl ketoxime. May produce an allergic reaction.Repeated exposure may cause skin dryness or cracking.Take precautionary measures against static discharge.Wear eye protection.IF ON SKIN (or hair): Remove immediately all contaminated clothing.Rinse skin with water.In case of fire: Use carbon dioxide for extinction.Store in a well-ventilated place. Keep cool.Dispose of contents/container to hazardous or special waste collection point.
gloss finish for woodand cork
Clear
gloss finish for woodand cork
Clear
IMPORTANTFactory pre-sealed cork floor tiles may be wax coated which will affectthe drying of Rustin’s Polyurethane Floor Sealer. Test on a spare tile ora small area of the floor. If the coating still remains tacky after eight toten hours the floor should be dewaxed with White Spirit and steel
wool, wiping whilst still damp with clean rag.
World’s finest range of products for the
professional & homehandyman
For information on Rustins’products visit our website atwww.rustins.co.uk or contact usat Rustins Ltd, Waterloo Road,London, NW2 7TX United [email protected]: +44 (0)20 8450 4666
Rustins’ range includes:Acrylic VarnishesAluminium PaintsBitumen BlackBlack Matt PaintBlackboard BlackBrick & Tile PaintClear Metal Lacquerfor Brass & Copper
Danish OilFrench PolishesGold PaintGrainfillerKnottingPaint, Gloss & Undercoat
Polyurethane VarnishesPrimersQuick Drying ColouredVarnishes
Radiator PaintRust RemoverStrypit Paint & VarnishStripper
Teak OilWallpaper RemoverWood DyesWoodstoppingYacht Varnish
Contents will coverapproximately35 sq. metres
(375 sq. ft.) one coat
21/2 litres Made in UK
EU Limit value for this product (CAT A/i): 500g/l (2010)
This product contains max 460 g/l VOC
WARNING
20160321_LAB_0221022 Polyurethane Floor Sealer Gloss 2.5l_0213329 Floor Seal Gloss 2.5l 21/03/2016 15:44 Page 1
