Getting Started with UDOO and installing Scilab on UDOO

#9/3,Shree Lakshmi complex,2nd

Floor,Opp,To Vivekananda Park,Girinagar,Bangalore-560085.www.tenettech.com

2013

Author: Praveen Kumar R

Email ID:[email protected]

Getting Started with UDOO and installing Scilab on UDOO



Quick introduction about UDOO UDOO is an newly launched multi Development platfrom solution for Linux,Android,Arduino and Google ADK(2012).It has main processor as iMX6 ARM-

CORTEX A9 from freescale.1GHz and RAM 1 GB DDR3.And it has the ARM Cortex-M3 controller which is same as Arduino DUE

Distributions Ubuntu 12.04

Android 4.2.2 Jelly Bean

Arduino IDE (by default)

Features Freescale i.MX 6 ARM Cortex-A9 CPU Dual/Quad core 1GHz

Integrated graphics, each processor provides 3 separated accelerators for 2D,

OpenGL® ES2.0 3D and OpenVG™

Atmel SAM3X8E ARM Cortex-M3 CPU (same as Arduino Due)

RAM DDR3 1GB

76 fully available GPIO

Arduino-compatible R3 1.0 pinout

HDMI and LVDS + Touch (I2C signals)

Ethernet RJ45 (10/100/1000 MBit)

WiFi Module

Mini USB and Mini USB OTG

USB type A (x2) and USB connector (requires a specific wire)

Analog Audio and Mic

SATA (Only Quad-Core version)

Camera connection

Micro SD (boot device)

Power Supply 12V and External Battery connector

http://blog.arduino.cc/category/arduino/adk/

http://arduino.cc/en/Main/arduinoBoardDue



Booting Ubuntu on UDOO Steps for porting image to micro SD card Step 1:

Download the Win32 Disk Imager(tool for porting an image) from the here.

Insert your microSD Card and then run Win32 Disk Imager.exe. It may give an error message on startup, but you can often ignore it. It should find your SD Card drive or if not select it. You can get the prebuilt image from here. Unzip and select the file '#.img' image file you wish to use and then press write. Once it completes you are ready to go, insert your microSD card into the UDOO micro SD slot(I am using UDOO Quad)

Copying image to SD card

Backup

Selecting Drive

http://sourceforge.net/projects/win32diskimager/files/latest/download

http://www.udoo.org/downloads/



Step 2: Click write button and select your image as per the image shown below. After ten minutes it will display a successful message.

Step 3: Insert the micro SD card.Connect the power adapter 12v 2A,then HDMI cable for video out,usb keyboard and mouse.For internet connection i am using inbuilt Wi-Fi.



Step 4: After powering up the board ,ubuntu 11.10 starts booting.It wont ask for username and password,directly go to the Desktop.you can find the Desktop picture of UDOO below.

UDOO Desktop

Scilab installation on UDOO For more details about click here Step 1: sudo apt-get update Step 2: Make sure the java is installed in the system using by the following command.

$ java –version

http://www.scilab.org/



Step 3:

Install scilab from the command prompt.It will download nearly 150 MB of data for installation. $ sudo apt-get install scilab –y

Step 4: After sometime you will get a successful message like below.



Step 5: ApplicationsScienceScilab

Step 6:

Scilab console



Scilab Xcos Window

For placing an order: UDOO Quad For queries: [email protected]

Contact: 080-26722726

http://www.tenettech.com/product/3162/udoo-quad

mailto:[email protected]

Getting Started with UDOO and installing Scilab on UDOO

Documents

Transcript of Getting Started with UDOO and installing Scilab on UDOO