Getting Started in Mfs
-
Upload
jose-manuel-coronado-saucedo -
Category
Documents
-
view
214 -
download
0
Transcript of Getting Started in Mfs
-
8/18/2019 Getting Started in Mfs
1/62
-
8/18/2019 Getting Started in Mfs
2/62
-
8/18/2019 Getting Started in Mfs
3/62
Getting Started inMastercam for
SolidWorks®
January 2009
Be sure you have the latest information!
Information might have been changed or added since this document was published. The latest version of this document is installed with
Mastercam for SolidWorks or can be obtained from your localMastercam Reseller.
-
8/18/2019 Getting Started in Mfs
4/62
ii – Getting Started in Mastercam for SolidWorks
Getting Started in Mastercam® for SolidWorks®
Date: January 2009
Copyright © 2009 CNC Software, Inc.—All rights reserved.First Printing: January 2009
Software: Mastercam for SolidWorks/ Mastercam X3 MU1
ISBN: 1-883310-90-3
IMPORTANT NOTICE!
PLEASE READ THIS STATEMENT AND THE SOFTWARE LICENSE AGREEMENT
COMPLETELY BEFORE USING THIS SOFTWARE. YOU MUST ACCEPT THE TERMS OFTHIS LICENSE BEFORE YOU CAN OPERATE THE SOFTWARE PROGRAM.
BY AGREEING TO THE LICENSE BELOW, OR BY CONTINUING TO USE THIS
SOFTWARE, YOU (EITHER AN INDIVIDUAL OR A SINGLE ENTITY) INDICATE YOUR
INTENTION TO BE BOUND BY AND ACCEPT THE TERMS AND CONDITIONS OF THIS
SOFTWARE LICENSE. IF YOU DO NOT AGREE TO THESE TERMS AND CONDITIONS,
YOU MAY NOT ACCESS OR OTHERWISE USE THIS SOFTWARE AND WILL IN FACT BEPROHIBITED FROM DOING SO. THIS COMPUTER SOFTWARE MAY BE USED ONLYPURSUANT TO THE TERMS AND CONDITIONS SET FORTH BELOW, AND SOLELY IN
CONJUNCTION WITH THE ACCOMPANYING SECURITY MECHANISM (UNLESSOTHERWISE SPECIFIED IN THE “EXCEPTIONS TO SECURITY MECHANISMREQUIREMENTS” SECTION OF SUCH TERMS AND CONDITIONS) WHICH MUST BE
PRESENT ON YOUR COMPUTER (OR NETWORK AS APPLICABLE) AT ALL TIMESDURING SUCH USE.
Please Note: Your company may have additional restrictions and guidelines in place
regarding the use of this Software that are in addition to those found within this SoftwareLicense. If you have any questions or concerns as to the existence of any such additionalrestrictions or guidelines, you should consult with your supervisor or your IT Department
before using this Software.
Read This If You Have Received This Software From A Third Party : If you received thisSoftware from someone other than an authorized CNC Software, Inc. reseller, you do not
have a legal software license. (For example, if you acquired this Software simply bybuying a machine or Software from the former owner or from an auction, you do not havea valid license.) You should contact CNC Software, Inc. (860-875-5006) in order to obtain
a new and valid license. Use of this Software without a valid software license isunlawful, a violation of the Copyright Act and may expose you to criminal liability
under 17 United States Code Sec. 506, including fines and damages.
-
8/18/2019 Getting Started in Mfs
5/62
iii
Software License
If you have paid a license fee, CNC Software, Inc. (“CNC”) a Connecticut corporation with
its principal place of business at 671 Old Post Road, Tolland, Connecticut, 06084 herebygrants to you a non-exclusive, non-transferable license (the “License”) to use thissoftware program and its accompanying documentation (and, if applicable, to permit
your authorized employees to use them), solely in accordance with the terms andconditions of this Software License Agreement. You may use the Software solely for yourinternal business purposes and solely in conjunction with the accompanying hardware or
software device, method, scheme or other security measure provided by CNC whichallows a user to access the Software and prevents unauthorized access to the Software(the “Security Mechanism”). The Software, any updates to the Software through
purchase or due to enrollment in an authorized software Maintenance program(including any that you download through the Internet), and the Documentation in
printed or electronic form shall hereinafter collectively be referred to as the “Software”and are all governed by this License.
Restrictions
You may not use the Software without a Security Mechanism provided by CNC or CNC’ssuppliers. When CNC or CNC’s resellers provide you with a single-user SecurityMechanism, the Software may only be used (in executable code form only) on a single
computer to which the Security Mechanism is physically attached. In the event CNC orCNC’s resellers provide you with a multiple-user Security Mechanism for use over aninternal network (a “Network Security Mechanism”), the Software may be used: (a) in
executable code form only; (b) only on end-user computers that are connected to the
internal network to which the Network Security Mechanism is attached; and (c) only bythe number of users and accessed by the number of end-user computers for which
licenses were purchased and as further allowed by the Network Security Mechanism. Youmay physically transfer the Software from one computer equipped with a single-userSecurity Mechanism to another only if the Security Mechanism is included in the transfer
and is installed with the new computer.
You shall not: (a) copy (except as provided below), adapt, modify the Software; (b)publish, display, disclose or create a derivative work from the Software or any part
thereof; (c) de-compile or translate, disassemble, create or attempt to create, by reverseengineering or otherwise, the source code form of the Software from the executable code
of the Software; (d) remove any proprietary notices, labels or marks from the Software; (e)sell, rent, lease, distribute or otherwise transfer or provide all or any part of the Softwareto any person or entity without the prior written consent of CNC; (f) use the Software toprovide outsourcing, service bureau, time sharing or other services to any third party; or
(g) sublicense, assign, delegate or otherwise transfer your rights in the Software, underthe Software License Agreement or any of the related rights or obligations for any reason without the prior written consent of CNC. You shall not circumvent, bypass, modify,
-
8/18/2019 Getting Started in Mfs
6/62
iv – Getting Started in Mastercam for SolidWorks
reverse engineer, disassemble, disable, alter, enhance or replicate the function of theSecurity Mechanism in any manner whatsoever. Any attempt to do so shall result in
automatic termination of this License without prejudice to all other legal rights and
remedies of CNC.
Copying Restrictions
You may make one (1) copy of the Software for backup or archival purposes, providedthat you reproduce all proprietary notices of CNC on any such copy.
Non Transferable
You may not transfer or assign the Software or this Software License Agreement or any
rights or obligations hereunder. Any attempt to do so will automatically terminate thisLicense without the need for notice. This termination is without prejudice to all other
legal rights and remedies of CNC.
Intellectual Property Rights
The Software is and includes intellectual property of CNC. All associated intellectual
property rights, including, without limitation, worldwide patent, trademark, copyrightand trade secret rights, are reserved by CNC. CNC retains all right, title and interest inand copyrights to the Software, regardless of the form or media in or on which the
original or other copies may subsequently exist. This Software License Agreement shallnot constitute a sale of the Software and no title or proprietary rights to the Software aretransferred to you hereby. You acknowledge that the Software is a unique, confidential
and valuable asset of CNC, and CNC shall have the right to seek all equitable and legal
redress which may be available to it for the breach or threatened breach of this SoftwareLicense Agreement including, without limitation, injunctive relief. Unauthorized copying
of the Software or failure to comply with the above restrictions shall result in automatictermination of this License and this Software License Agreement without prejudice to allother legal rights and remedies of CNC.
Confidentiality
You acknowledge that the Software contains proprietary trade secrets of CNC and you
hereby agree to maintain the confidentiality of the Software using at least as great adegree of care as you use to maintain the confidentiality of your own most confidential
information. You agree to promptly communicate the terms and conditions of thisSoftware License Agreement to those persons employed by you who come into contact with the Software, and to use your best efforts to ensure their compliance with such termsand conditions, including, without limitation, absolutely preventing such persons to use
any portion of the Software for the purpose of deriving the source code of the Software ordefeating the Security Mechanism.
-
8/18/2019 Getting Started in Mfs
7/62
v
Enforcement Obligations
In the event you become aware that any person or entity in your employ or under your
control is using the Software in a manner not authorized by this Software License Agreement, you shall immediately take all steps necessary to stop such unauthorized use
of the Software. You shall promptly notify CNC in writing of any unauthorized use of theSoftware of which you become aware.
Limited Warranties
CNC WARRANTS THAT THE MEDIA ON WHICH THE SOFTWARE IS DISTRIBUTED WILL BE FREE OF DEFECTS IN MATERIAL OR WORKMANSHIP FOR A PERIOD OF
THIRTY (30) DAYS AFTER PURCHASE. THE FOREGOING LIMITED WARRANTYEXCLUDES DEFECTS ARISING OUT OF ACCIDENT, NEGLECT, MISUSE, FAILURE OFELECTRIC POWER AND CAUSES OTHER THAN ORDINARY AND AUTHORIZED USE.
EXCEPT FOR THE FOREGOING LIMITED WARRANTY, THE SOFTWARE IS PROVIDED“AS IS, WITH ALL FAULTS.” THIS LIMITED WARRANTY IS THE ONLY WARRANTYPROVIDED BY CNC REGARDING THE SOFTWARE. TO THE MAXIMUM EXTENT
PERMITTED BY LAW, CNC DISCLAIMS ALL OTHER WARRANTIES OF ANY KIND,EITHER EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
CNC IS NOT OBLIGATED TO PROVIDE ANY UPDATES TO THE SOFTWARE.
Sole and Exclusive Remedy for Breach of Warranty: YOUR SOLE EXCLUSIVE REMEDY AND CNC’S SOLE OBLIGATION HEREUNDER SHALL BE, AT CNC’S SOLE OPTION (i)
REPLACEMENT OF THE DEFECTIVE MEDIA; OR (ii) REFUND OF THE PURCHASE
PRICE OF THE SOFTWARE. CNC SHALL HAVE NO OTHER OBLIGATION OR LIABILITYTO YOU ARISING FROM OR RELATED TO THIS LICENSE OR YOUR USE OF THE
SOFTWARE. ANY USE BY YOU OF THE SOFTWARE IS AT YOUR OWN RISK.
Note on Documentation: While CNC makes every effort to ensure that itsDocumentation for the Software is accurate and up-to-date, it cannot guarantee the
Documentation at all times represents the latest operation and functionality of theSoftware. The content of all documentation, in electronic or printed form, for theSoftware is provided for informational purposes only. The content of the Documentation
may be changed without notice to you. CNC expressly disclaims any warranty orrepresentation that the Documentation is an accurate and/or current reflection of the
Software’s operation and performance.
Disclaimer of Consequential Damages and Limitation of Liability
IN NO EVENT WHATSOEVER WILL CNC, OR ITS EMPLOYEES, SHAREHOLDERS,
DISTRIBUTORS OR RESELLERS BE LIABLE TO YOU FOR ANY INDIRECT, INCIDENTAL,OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH THISSOFTWARE LICENSE AGREEMENT OR THE USE OF THE SOFTWARE, EVEN IF CNC HAS
-
8/18/2019 Getting Started in Mfs
8/62
vi – Getting Started in Mastercam for SolidWorks
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. WITHOUT LIMITING THEFOREGOING, CONSEQUENTIAL DAMAGES SHALL INCLUDE, WITHOUT LIMITATION,
SPECIAL, PUNITIVE OR EXEMPLARY DAMAGES, DAMAGES FOR LOSS OF BUSINESS,
LOSS OF PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, AND LOSS OF OR DAMAGE TO ANY PRODUCTS THAT THE SOFTWARE IS USED IN
CONJUNCTION WITH.
CNC’S ENTIRE LIABILITY WITH RESPECT TO ITS OBLIGATIONS UNDER THISSOFTWARE LICENSE AGREEMENT OR OTHERWISE SHALL NOT EXCEED THE
AMOUNT OF THE LICENSE FEE PAID BY YOU FOR THE SOFTWARE. SOMEJURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF IMPLIED WARRANTIES OR LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO
THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU.
Indemnification
You shall indemnify and hold harmless CNC, its officers, directors, employees, resellersand agents (the “Indemnified Parties”) from and against all losses, settlements, claims,actions, suits, proceedings, judgments, awards, damages, liabilities, costs and expenses
including, without limitation, reasonable attorneys’ fees (collectively “Losses”) whicharise out of or are related to any breach of this Software License Agreement by you or youremployees, agents, resellers, dealers or sub-dealers, and shall reimburse the Indemnified
Parties for any and all legal, accounting and other fees, costs and expenses reasonablyincurred by any of them in connection with investigating, mitigating or defending anysuch Losses.
Educational Pricing
If this Software was obtained through or in accordance with a CNC “Educational Pricing”
plan, option, grant, schedule or program, it may not be used by anyone, including you, toconduct any computer aided design, computer aided drafting, computer aidedmachining, or training activities that, directly or indirectly, generate or otherwise result in
monetary revenues for the benefit of any individual or any entity, other than the schoolthat originally received this Software.
Termination
This Software License Agreement is effective until terminated. You may terminate this
Software License Agreement at any time by returning to CNC all copies of the Softwareunder your control and by returning the Security Mechanism to CNC. CNC mayterminate this Software License Agreement if CNC determines, in its sole discretion, that you have violated the terms of this Software License Agreement. Upon termination of this
Software License Agreement, you agree to immediately return to CNC all copies of theSoftware, return the Security Mechanism to CNC, and certify to CNC in writing that allknown copies, including backup copies, have been returned. All provisions relating to
-
8/18/2019 Getting Started in Mfs
9/62
vii
confidentiality, proprietary rights, indemnification and non-disclosure shall survive thetermination of this Software License Agreement. You may not transfer this Software to
the purchaser of any equipment on which the Software may be resident. You may not
transfer this Software via liquidation, bankruptcy, auction, close of business, or anyother method that does not involve an authorized Mastercam reseller. This License is
for you alone. In the event you breach the provisions of this Section, CNC shall beentitled to liquidated damages in the amount of Fifteen Thousand Dollars ($15,000), plusits reasonable attorney’s fees and court costs.
General
This Software License Agreement shall be governed by and construed in accordance with
the laws of the state of Connecticut, USA without regard for Connecticut’s conflicts of lawprinciples. The sole and exclusive jurisdiction and venue for any litigation arising from orrelated to this Software License Agreement or the subject matter hereof shall be in an
appropriate state or federal court located in Hartford, Connecticut. You hereby submit tothe personal jurisdiction of the US District Court for the District of Connecticut and theSuperior Court of the State of Connecticut. This Software License Agreement shall
constitute the entire agreement between you and CNC with respect to the subject matterhereof. Any waiver or modification of this Software License Agreement shall be valid onlyif it is in writing and signed by both parties hereto. If any part of this Agreement is found
invalid or unenforceable by a court of competent jurisdiction, the remainder of this Agreement shall be interpreted so as to reasonably affect the intention of the parties.
Attorneys Fees
In the event that CNC is required to take legal action to enforce its rights under thisLicense Agreement and obtains a ruling or settlement in its favor, you shall be liable to
CNC for its reasonable attorney’s fee incurred in investigating and prosecuting its claim.
U.S. Government Restricted Rights
The Software provided hereunder is a “commercial item,” as that term is defined in 48C.F.R. 2.101, consisting of “commercial computer software” and “commercial computersoftware documentation,” as such terms are used in 48 C.F.R. 12.212. Consistent with 48
C.F.R. 12.212 and 48 C.F.R. 227.7202-1 through 227.7202-4, the Software made available tothe United States of America, its agencies and/or instrumentalities, is provided with onlythose rights set forth in this Agreement. Use, duplication or disclosure of the Software by
the government is subject to the restrictions as set forth in subparagraph (c) (1) and (2) ofthe Commercial Computer Software-Restricted Rights clause at 48 C.F.R. 52.227-19, asamended, or any successor regulations thereto.
Export Restrictions
You represent and warrant that you will not, without obtaining prior written
authorization from CNC and, if required, of the Bureau of Export Administration of the
-
8/18/2019 Getting Started in Mfs
10/62
viii – Getting Started in Mastercam for SolidWorks
United States Department of Commerce or other relevant agency of the United StatesGovernment, export or re-export, directly or indirectly, the Software from the United
States to (i) any country destination or entity to which export is restricted by the Export
Administration Regulations of the United States Department of Commerce; (ii) anycountry or entity subject to sanctions administered by the Office of Foreign Assets
Control, United States Department of the Treasury; or (iii) such other countries or entitiesto which export is restricted by any other United States government agency. You furtheragree that you are solely responsible for compliance with any import laws and regulations
of the country of destination of a permitted export or re-export, and any other importrequirement related to a permitted export or re-export.
Exceptions to Security Mechanism Requirements
CNC software programs Mastercam Design LT and Mastercam Demo as well as printedand electronic documentation do not require the use of Security Mechanisms, and the
provisions in this Software License Agreement relating to Security Mechanisms do notapply to your use of such programs, provided, however, that such provisions shall applyto your use of all other Software and documentation provided hereunder.
Survival
All provisions of this Software License Agreement relating to confidentiality, non-
disclosure, CNC’s proprietary rights, disclaimers, and limits of liability, orindemnification by Customer shall survive termination of this License for any reason.
Reservation of Rights
All rights not expressly granted are reserved by CNC.
Trademarks
Mastercam® is a registered trademark of CNC Software, Inc.
SolidWorks® is a registered trademark of Dassault Systèmes Corporation
Windows, Windows 2000, Windows XP, and Windows Vista are registered trademarks ofMicrosoft Corporation. Mastercam Verify is created in conjunction with MachineWorksLtd. Mastercam Backplot includes Copyrighted intellectual property rights owned by
NWD.
Printed in the United States of America.
Printed on recycled paper.
-
8/18/2019 Getting Started in Mfs
11/62
ix
Contents1.
Introducing Mastercam for SolidWorks ......................... 1
Videos and Documentation .................................................... 1
Watching the Videos ................................................................. 1
Using the Help ........................................................................... 3
Interface Tour ............................................................................ 5
Considerations and Limitations ............................................ 7
2.
Installation ..................................................................................... 9
Licensing ................................................................................... 10
Installing a HASP (Single-User License) ............................ 10
Using a NetHASP (Network Licensing) ............................... 11
Installing Mastercam for SolidWorks ................................. 12
Entering the SIM Update Code ............................................ 16
Updating HASP Codes ........................................................... 17
3.
General Work Flow ................................................................... 21
4. Basic Part Drawing in SolidWorks ................................... 27
Drawing a Part ......................................................................... 28
Changing the Default Tool Plane ......................................... 37
The Mastercam Gnomon ....................................................... 38
5.
Miscellaneous Tasks ................................................................ 41 Configuration .......................................................................... 41
Tool Manager ........................................................................... 42
Material Manager.................................................................... 42
Machine Definition Manager ............................................... 43
-
8/18/2019 Getting Started in Mfs
12/62
x – Getting Started in Mastercam for SolidWorks
Control Definition Manager ................................................. 44
6.
Mastercam for SolidWorks FAQ ........................................ 45
General ...................................................................................... 45
Compatibility ........................................................................... 46
Licenses ..................................................................................... 47
-
8/18/2019 Getting Started in Mfs
13/62
chapter 1
Introducing Mastercamfor SolidWorks
Mastercam® for SolidWorks® provides Mastercam X3 CAMfunctionality within SolidWorks. Inside SolidWorks, you can access 3Dhigh speed (HST) toolpath strategies and Mastercam’s new 2D FeatureBased Machining (FBM) automated mill and drill toolpath generation. Also, Mastercam for SolidWorks supports boundary creation, part setup(including tool and material managers), verification, post processing,and communications.
Videos and DocumentationMastercam for SolidWorks includes tutorial videos and Help. You canfind information about additional tutorials onwww.mastercamforsolidworks.com.
Watching the VideosThe videos provide a brief introduction to Mastercam for SolidWorks.Please watch these videos first . You can repeat any video section at yourown pace.
-
8/18/2019 Getting Started in Mfs
14/62
2 – Getting Started in Mastercam for SolidWorks
From the SolidWorks menu bar, choose Help, and then choose Videos in the Mastercam Help section.
When the video starts, maximize the window and scroll down until youcan see the caption and video controls (see below).
-
8/18/2019 Getting Started in Mfs
15/62
Introducing Mastercam for SolidWorks - 3
Using the Help
The Help is a subset of the full Mastercam Help and provides primarilycontext-sensitive information for the dialog boxes that display as you work with the product. Click a dialog box’s Help button to view theassociated help topic.
-
8/18/2019 Getting Started in Mfs
16/62
4 – Getting Started in Mastercam for SolidWorks
Some Mastercam dialog boxes display in the SolidWorks style. Thosedialog boxes, too, have Help buttons that open the Mastercam for
SolidWorks Help.
The Help also includes high-level conceptual topics that describeMastercam for SolidWorks. To access these topics, choose Help fromthe SolidWorks menu bar, and then choose Contents in the MastercamHelp section.
-
8/18/2019 Getting Started in Mfs
17/62
Introducing Mastercam for SolidWorks - 5
Interface TourMastercam for SolidWorks is integrated into the SolidWorks interface.The Mastercam menu provides access to all Mastercam for SolidWorksfunctionality in the SolidWorks menu bar.
The most used Mastercam for SolidWorks functions are also availablefrom the SolidWorks Command Manager above the Mastercam tab.
-
8/18/2019 Getting Started in Mfs
18/62
6 – Getting Started in Mastercam for SolidWorks
The familiar Mastercam Toolpath Manager is an integral part ofMastercam for SolidWorks. All function buttons are supported and
operate as in Mastercam.
Appropriate Toolpath Manager right-click menu functionality is alsosupported.
-
8/18/2019 Getting Started in Mfs
19/62
Introducing Mastercam for SolidWorks - 7
Considerations and LimitationsMastercam for SolidWorks operates differently than the full version ofMastercam. Please be aware of the following issues:
Mastercam and SolidWorks differ in the use of planes. Formore information, see Chapter 4, “Basic Part Drawing inSolidWorks” on page 27.
You must use SolidWorks selection methods. Mastercamselection methods have been removed.
Parts that are appropriate for HST machining strategies in
Mastercam can be programmed in Mastercam for SolidWorks.
You must not resize the screen during backplotting.
Rotary simulation is not yet functional.
Mastercam for SolidWorks will not install with 64-bitSolidWorks.
-
8/18/2019 Getting Started in Mfs
20/62
8 – Getting Started in Mastercam for SolidWorks
-
8/18/2019 Getting Started in Mfs
21/62
chapter 2
Installation
To install and run Mastercam for SolidWorks, you must haveadministration privileges and the following:
SolidWorks 2008 or 2009 installed (32-bit version)
Mastercam for SolidWorks installation files
Valid Mastercam for SolidWorks license (HASP SIM orNetHASP)
Update code information (current users only)
Minimum requirements for Mastercam for SolidWorks:
Operating System: Windows XP® (preferred) or Windows Vista® (Business or Ultimate), including the latest servicepacks and recommended updates. NET 3.0 framework.
Software: SolidWorks 2008 or SolidWorks 2009. (Note thatMastercam will not install in a SolidWorks 64-bit version.)
Processor: 1.5 GHz 32-bit Intel®-compatible processor. 64-bitIntel®-compatible processors are supported.
Memory: 2 GB (minimum). Your use of the software couldrequire more RAM to ensure optimal performance.
Virtual memory: Double the amount of RAM.
Graphics Card: Certified OpenGL graphics card and driver. Goto www.solidworks.com/sw/support/videocardtesting.html for a complete list of certified graphics cards.
http://www.solidworks.com/sw/support/videocardtesting.htmlhttp://www.solidworks.com/sw/support/videocardtesting.htmlhttp://www.solidworks.com/sw/support/videocardtesting.htmlhttp://www.solidworks.com/sw/support/videocardtesting.html
-
8/18/2019 Getting Started in Mfs
22/62
10 – Getting Started in Mastercam for SolidWorks
Hard Disk Space: 2 GB available hard disk space (minimum).
Monitor: 1024 x 768 pixel resolution (minimum) at 96 dpi
(1280 x 1024 recommended). Mouse: 2-button Windows® compatible mouse (minimum).
Network Protocol: (NetHASP users only) TCP/IP protocol forNetHASP installation; VPN is unsupported.
Other: DVD drive. Adobe Acrobat Reader 7.0.7 or higher.Internet Explorer 6.x or 7.x.
LicensingMastercam for SolidWorks supports both single-user and networklicensing. With single-user licensing, you need a small device called aHASP SIM. The standard HASP SIM is a USB device. If your computercannot accept a USB device, you can obtain a parallel HASP SIMthrough your Authorized Mastercam Reseller for an extra charge.
With network licensing, you need a device called a NetHASP (parallel or
USB) SIM. This device is also called a network SIM and must beinstalled on a network PC.
These devices protect against illegal use of Mastercam software.
Installing a HASP (Single-User License)To install the single-user license:
Turn off the computer, monitor, and all external peripheral
devices. Based on the type of HASP, locate an available parallel or USB
port on the computer. If you are unsure of the port’s location,consult your computer documentation.
-
8/18/2019 Getting Started in Mfs
23/62
Installation - 11
Plug the male end of the HASP into the port.
Caution: The HASP attaches to your port in only one orientation. Donot force it, because you might damage the port and the HASP. If theHASP does not slide easily into the port, check its orientation. Matchthe HASP to the port and try again. Also, check the HASP fordamaged pins. If the pins are damaged, and you cannot easilystraighten them, contact your Mastercam Reseller for a replacement.
If you are installing a HASP to a parallel port, tighten the two
screws on the HASP to firmly attach it to your computer.
If necessary, connect your printer cable to the HASP. Thentighten the screws on the printer cable connector to firmlyattach it to the HASP.
Note: You can connect a printer cable to the back of a parallel HASPand continue to use the port for printing.
Using a NetHASP (Network Licensing) With network licensing, a group of users who are connected to the samenetwork can run Mastercam for SolidWorks from any PC on thenetwork. Instead of requiring one HASP per computer to runMastercam, a single NetHASP is installed on any PC on the network.That computer is referred to as the NetHASP server; it is not necessarilya network server. An individual Mastercam user then checks out a
license from the available licenses on the network when startingMastercam for SolidWorks.
-
8/18/2019 Getting Started in Mfs
24/62
-
8/18/2019 Getting Started in Mfs
25/62
Installation - 13
3 Read the agreement, select I accept the terms of thelicense agreement, and then click Next.
4
Enter your user and company name, and then click Next.5 Select an installation path (or leave the default), and click
Next.
6 Select your SIM type and the default measurement units,and then click Next.
7 Click Install to finalize your choices and to begin theinstallation.
8 When installation completes, click Finish.
To verify the installation
1 Start SolidWorks.
2 In the Tools menu, select Add-Ins.
-
8/18/2019 Getting Started in Mfs
26/62
14 – Getting Started in Mastercam for SolidWorks
3 Find Mastercam for SolidWorks in the Add-Ins dialogbox, and check the Active Add-ins box, if necessary.
-
8/18/2019 Getting Started in Mfs
27/62
Installation - 15
4 If you want Mastercam for SolidWorks to startautomatically with SolidWorks, select the check box in theStart Up column.
5 Click OK to finalize your choices.
6 In the SolidWorks menu bar, make sure that you have aMastercam menu.
-
8/18/2019 Getting Started in Mfs
28/62
16 – Getting Started in Mastercam for SolidWorks
Entering the SIM Update Code
When you install or upgrade Mastercam for SolidWorks, and you arenot on Mastercam Maintenance, you must update your HASP andNetHASP SIMs with an update code. The SIM must be activated withthe update code before you can run the new or updated version ofMastercam for SolidWorks.
The update code is a file that is delivered to you by one of thesemethods:
Included with your Mastercam for SolidWorks software kit
Mailed on electronic media E-mailed as a file attachment
Printed documentation received via fax, e-mail, or mail
Note: You should remove any SIMs other than the Mastercam forSolidWorks SIM before entering the update code.
Before entering the update code, prepare for the update based on theformat of the update code you received and your personal preference:
E-mail attachment: Save the attachment as a file to anaccessible location. (Do not change the file extension.)
Mastercam for SolidWorks installation kit electronic media:Insert the media in the appropriate drive to access the file.
Printed documentation: Have a copy of the documentavailable.
-
8/18/2019 Getting Started in Mfs
29/62
Installation - 17
Updating HASP Codes
IMPORTANT : Before you begin this phase of the installation process, be sure you have read the previous sections “Installing
a HASP (Single-User License)” and “Installing Mastercam for
SolidWorks.”
To enter a HASP update code
1 Choose ONE of the following methods to run HaspX.exe.The method you choose is based on the format of the
update code you received and your personal preference:♦ In the Mastercam Help section of the SolidWorks
Help menu, choose About Mastercam forSolidWorks. In the About Mastercam dialog box,click Hasp.
-
8/18/2019 Getting Started in Mfs
30/62
18 – Getting Started in Mastercam for SolidWorks
♦ From the Windows desktop, choose Start, AllPrograms, Mastercam X3 MU1 in SolidWorks,
Hasp X.
♦ Double-click the update code file (*.HCODE).
♦ Use Windows Explorer to navigate to the Mastercamfor SolidWorks installation location, and double-clickHaspX.exe.
The HaspX utility analyzes the SIM and displays theSIM serial number. Verify that the displayed serial
number matches the serial number provided with your Mastercam for SolidWorks documentation.
-
8/18/2019 Getting Started in Mfs
31/62
Installation - 19
TIP: Keep a record of the serial number in the event that you
need to contact Technical Support Services at CNC Software or
your Mastercam Reseller.
2 In the HaspX dialog box, use one of the following methodsto enter the update code:
♦ If you received your update code as a file, chooseUpdate code to open the code file. The HaspX utilityextracts the update code from the file.
♦ If you received your update code as printeddocumentation, enter the code in the text field nextto the Update code button. (Do not click the Updatecode button.)
3 Choose Update at the top of the HaspX dialog box. Theprogram updates the SIM and displays the products for which the SIM has been activated.
4
Choose OK to exit the HaspX utility.
Notes:
Start date/End date: Displays the start date and end date forthe SIM. For some evaluation copies of Mastercam for
-
8/18/2019 Getting Started in Mfs
32/62
20 – Getting Started in Mastercam for SolidWorks
SolidWorks, the HASP SIM starts and expires on a specifieddate. You cannot use the software after the end date.
Maintenance Expiration date: This field shows the date yourMaintenance plan expires, based on your annual renewal date.
HASP Status: This area shows whether the utility found theHASP SIM on your computer.
-
8/18/2019 Getting Started in Mfs
33/62
chapter 3
General Work Flow
The general work flow for programming Mastercam toolpaths inSolidWorks will be familiar to a Mastercam user, as the following stepsshow. (For more detailed instructions, please refer to Chapter 4, “BasicPart Drawing in SolidWorks.” Also, you can find information aboutadditional tutorials on www.mastercamforsolidworks.com.)
1 Open a SolidWorks part. (To create one, see Chapter 4,“Basic Part Drawing in SolidWorks” on page 27.)
2 Set a tool plane, as follows:
a. Choose View Manager from the Command Manager.
b. In the View Manager dialog box, select the plane you want to use (1 below), and click the set tool planebutton (2 below).
c. Click OK.
-
8/18/2019 Getting Started in Mfs
34/62
22 – Getting Started in Mastercam for SolidWorks
3 Click the Mastercam Toolpath Manager button (circledin the image below) to display the Mastercam forSolidWorks Operations Manager.
4 Set the machine group properties as needed. Rememberthat a stock definition is required for FBM Milling.
For more information on machine group properties,please refer to “Machine groups” in the Mastercam forSolidWorks Help.)
5 If appropriate, choose Mastercam, Create Boundary tocreate machining boundaries (see following image).
For more information on creating boundaries, pleaserefer to “Containment Boundaries” in the Mastercam forSolidWorks Help.
-
8/18/2019 Getting Started in Mfs
35/62
General Work Flow - 23
6 Use ONE of the following methods to choose a toolpath
type:♦ Choose HST Surface Toolpaths to program high
speed surface toolpaths.
HST toolpaths demonstrate the integration ofMastercam with SolidWorks selection methods. If you have pre-selected geometry, Mastercam appliesthe toolpaths to the selections. Otherwise,Mastercam applies the toolpaths to the entire part.(For more information, please see “HST Toolpaths”in the Mastercam for SolidWorks Help.)
-
8/18/2019 Getting Started in Mfs
36/62
24 – Getting Started in Mastercam for SolidWorks
Note: HST in Mastercam for SolidWorks does not support checksurfaces.
♦ Choose FBM Drill to have Mastercam detect andprogram drilled holes automatically. (For moreinformation, please see “FBM Drill Toolpaths” in theMastercam for SolidWorks Help.)
♦ Choose FBM Mill to have Mastercam detect andprogram closed, open, nested, and through pocketsautomatically. (For more information, please see
“FBM Mill Toolpaths” in the Mastercam forSolidWorks Help.)
7 Set the appropriate toolpath parameters, and create thetoolpath as you would in Mastercam.
-
8/18/2019 Getting Started in Mfs
37/62
General Work Flow - 25
8 Backplot the toolpath. (For more information, please see“Backplotting Toolpaths” in the Mastercam forSolidWorks Help.)
9 Verify the toolpath. (For more information, please see“Verifying Toolpaths” in the Mastercam for SolidWorksHelp.)
10 Edit the toolpath as necessary.
-
8/18/2019 Getting Started in Mfs
38/62
26 – Getting Started in Mastercam for SolidWorks
11 Post the toolpath. (For more information, see “PostingToolpaths” in the Mastercam for SolidWorks Help.)
12 When ready for machining, choose Mastercam,Communications to send the posted NC code to themachine. (See “Mastercam Communications” in theMastercam for SolidWorks Help.)
13 Cut the part.
-
8/18/2019 Getting Started in Mfs
39/62
chapter 4
Basic Part Drawing inSolidWorks
When Mastercam users draw parts in SolidWorks, they quickly discovera major difference in the two applications’ coordinate systems.Mastercam sets up its default planes like this:
The Z axis of the work coordinate system (WCS) is normal tothe Top plane.
The Top plane is the default tool plane.
-
8/18/2019 Getting Started in Mfs
40/62
28 – Getting Started in Mastercam for SolidWorks
But SolidWorks sets up its default planes like this:
The world Z axis is normal to the Front plane.
The Front plane is the default tool plane.
In other words, Mastercam’s Top plane is equivalent to SolidWorks’sFront plane. This means that, for the best compatibility withMastercam, start your SolidWorks drawing on the Front plane.
Drawing a PartPerform the following procedure to draw a simple Mastercam forSolidWorks part. (You can find information about additional tutorialson www.mastercamforsolidworks.com.)
-
8/18/2019 Getting Started in Mfs
41/62
Basic Part Drawing in SolidWorks - 29
To draw a basic Mastercam for SolidWorks part
1 Choose File, New.
2
In the New SolidWorks Document dialog box, click thePart button and then OK.
Note: If the New SolidWorks Document dialog box shows Templatesand Tutorial tabs, click the Novice button to return to Novice mode.
3 In the panel on the left, click Front Plane, and then clickthe Sketch button in the popup window that displays.
-
8/18/2019 Getting Started in Mfs
42/62
30 – Getting Started in Mastercam for SolidWorks
4 Click the Sketch tab in the Command Manager.
5 Click the small arrow next to the Rectangle tool, and selectCorner Rectangle from the menu that displays.
-
8/18/2019 Getting Started in Mfs
43/62
Basic Part Drawing in SolidWorks - 31
6 Click the Front plane’s origin, and draw a rectangletowards the upper-right.
7
Click the Smart Dimension button.
-
8/18/2019 Getting Started in Mfs
44/62
32 – Getting Started in Mastercam for SolidWorks
8 Place your mouse over the left-hand line and click.
9 Drag the dimension to the left, and click again.
10 Type 80 into the Modify box, and press [Enter].
-
8/18/2019 Getting Started in Mfs
45/62
Basic Part Drawing in SolidWorks - 33
11 Similarly to how you set the height, dimension the part’s width to 110.
12 Click the Features tab in the Command Manager.
-
8/18/2019 Getting Started in Mfs
46/62
-
8/18/2019 Getting Started in Mfs
47/62
-
8/18/2019 Getting Started in Mfs
48/62
-
8/18/2019 Getting Started in Mfs
49/62
-
8/18/2019 Getting Started in Mfs
50/62
-
8/18/2019 Getting Started in Mfs
51/62
Basic Part Drawing in SolidWorks - 39
You can toggle the display of Mastercam’s gnomons in the GraphicsOptions dialog box, which you access from the Mastercam, GraphicsOptions
menu command. To remove the gnomon from the screen,deselect both Show Tool Plane Icon and Show Machine Z Icon:
Alternatively, you can drag the sliders to change the icons’ transparencyfrom opaque to fully transparent.
-
8/18/2019 Getting Started in Mfs
52/62
40 – Getting Started in Mastercam for SolidWorks
.
-
8/18/2019 Getting Started in Mfs
53/62
chapter 5
Miscellaneous Tasks
Mastercam for SolidWorks includes the following functions for supporttasks. You can find detailed information about these features in theMastercam for SolidWorks Help.
ConfigurationTo access the System Configuration dialog box, choose Mastercam,Configuration from the SolidWorks menu bar. (For more information,
please refer to “System Configuration dialog box” in the Mastercam forSolidWorks Help.)
-
8/18/2019 Getting Started in Mfs
54/62
42 – Getting Started in Mastercam for SolidWorks
Tool Manager As in the full version of Mastercam, the Tool Manager lets you view andmanage tool libraries, the tools in your part file, and tool definitions. You can create new tools, edit existing tools, and copy tools betweenlibraries and machine groups. (For more information, please refer to“Tool Manager” in the Mastercam for SolidWorks Help.)
Material ManagerMastercam for SolidWorks also includes the Material Manager, where you can select, edit, and create materials that Mastercam forSolidWorks can use to calculate more accurate feed rates and spindlespeeds. (For more information, please refer to “Material Manager” inthe Mastercam for SolidWorks Help.)
-
8/18/2019 Getting Started in Mfs
55/62
Miscellaneous Tasks - 43
Machine Definition ManagerUse the Machine Definition Manager to configure your machine’scapabilities and features.
-
8/18/2019 Getting Started in Mfs
56/62
44 – Getting Started in Mastercam for SolidWorks
Standard machine definitions are installed with Mastercam forSolidWorks. However, modifications to the machine definition and
posts must be done using a licensed installation of Mastercam X3. Formore information, refer to “Machine Definition Manager” in theMastercam for SolidWorks Help.
Note: Although you can make changes to the part’s machinedefinition with Machine Definition Manager, you should not createnew definitions within Mastercam for SolidWorks.
Control Definition ManagerUse the Control Definition Manager to configure your machine controlto work with Mastercam and the machine’s post processor. See“Control Definition Manager” in the Mastercam for SolidWorks Help.
-
8/18/2019 Getting Started in Mfs
57/62
chapter 6
Mastercam forSolidWorks FAQ
GeneralQuestion: How does Mastercam for SolidWorks work?
Answer: It is an add-in to SolidWorks just like COSMOS, PhotoWorks,and PDMWorks.
Question: Is Mastercam for SolidWorks equivalent to Mastercam Level3?
Answer: It features a subset of Level 3’s functionality, including 3DHST-style toolpaths, FBM Drill, FBM Mill, Verify, Backplot,Communications, and posting.
Question: Is there an add-in for Mastercam Multiaxis?
Answer: Not yet.
Question: Is there an add-in for Mastercam Lathe?
Answer: Not yet.
-
8/18/2019 Getting Started in Mfs
58/62
-
8/18/2019 Getting Started in Mfs
59/62
Mastercam for SolidWorks FAQ - 47
LicensesQuestion: How will my Mastercam product work on a SolidNetWorklicense?
Answer: As long as the computer has an active license of SolidWorksrunning, Mastercam for SolidWorks will run.
Question: What happens when I open a SolidWorks file (with Mastercam toolpaths) in a seat of SolidWorks that does not have Mastercam?
Answer: The user will notice nothing different about the file.
-
8/18/2019 Getting Started in Mfs
60/62
-
8/18/2019 Getting Started in Mfs
61/62
-
8/18/2019 Getting Started in Mfs
62/62
671 Old Post Road
Mastercam is a registered trademark of CNC Software, Inc. ©Copyright 1983-2009. All rights reserved.SolidWorks is a registered trademark of DS SolidWorks Corporation.