Geotech 1.66” Auto-Reclaimer€¦ · Reclaimer requires only a regulated compressed air source to...
Transcript of Geotech 1.66” Auto-Reclaimer€¦ · Reclaimer requires only a regulated compressed air source to...
Rev 10/19/12 Part # 16600165
Geotech 1.66” Auto-Reclaimer
Installation and Operation
1
TABLE OF CONTENTS
CHAPTER 1: SYSTEM DESCRIPTION ............................................................... 3
FUNCTION AND THEORY ....................................................................................... 3 SYSTEM COMPONENTS ........................................................................................ 4
CHAPTER 2: SYSTEM INSTALLATION ............................................................. 5
TOP FILL ............................................................................................................. 5 BOTTOM FILL ....................................................................................................... 5 DUAL FILL ........................................................................................................... 7
CHAPTER 3: SYSTEM OPERATION .................................................................. 8
TOP FILL ............................................................................................................. 8 BOTTOM FILL ....................................................................................................... 8 DUAL FILL ........................................................................................................... 9
CHAPTER 4: SYSTEM MAINTENANCE ........................................................... 12
CHAPTER 5: SYSTEM TROUBLESHOOTING................................................. 13
CHAPTER 6: SYSTEM SPECIFICATIONS ....................................................... 14
CHAPTER 7: REPLACEMENT PARTS LIST.................................................... 19
THE WARRANTY ................................................................................................ 20
EQUIPMENT RETURN POLICY ......................................................................... 20
EQUIPMENT DECONTAMINATION ................................................................... 20
2
DOCUMENTATION CONVENTIONS
This manual uses the following conventions to present information:
An exclamation point icon indicates a WARNING of a situation or condition that could lead to personal injury or death. You should not proceed until you read and
thoroughly understand the WARNING message.
A raised hand icon indicates CAUTION information that relates to a situation or condition that could lead to equipment malfunction or damage. You should not proceed until you read and thoroughly understand the CAUTION message.
A note icon indicates NOTE information. Notes provide additional or supplementary information about an activity or concept.
WARNING
CAUTION
NOTES
3
Chapter 1: System Description
Function and Theory
The GEOTECH 1.66" Auto-Reclaimer top fill, bottom fill, or top/bottom fill system is a fixed intake, automatic total fluids recovery pump. The 1.66" Auto-Reclaimer will recover fluids from depths of up to 250 ft. The GEOTECH Auto-Reclaimer is an automatic and controllerless, positive air-displacement pump. The Auto-Reclaimer works without the use of any external controls, relays, bleeder tubes or bubblers. The Auto-Reclaimer requires only a regulated compressed air source to operate. The Auto-Reclaimer requires an operating pressure of only 1 PSI above static head. The Auto-Reclaimer does not require clean, dry air to function properly, and can operate on contaminated or industrial air. The GEOTECH Auto-Reclaimer can operate under both positive and *negative (vacuum) pressure environments. The Auto-Reclaimer self-adjusts the discharge flow rate automatically to match individual well recharge rates (up to the pumps maximum capacity).
The Auto-Reclaimer will pump large particulates up to 1/16" in diameter without problems. The unique single self-cleaning valve mechanism will pass high viscosity gear oils without fouling.
* Vacuum conditions may require a Vacuum Equalizer if venting out of the recovery well. Contact your technical sales representative for more information.
4
System Components
The GEOTECH Auto-Reclaimer system components consist of an Upper Head Valve Assembly, Internal Float Assembly, Bottom Intake Assembly (for Bottom Fill, Top/Bottom Fill), and a Top Fill Intake Screen Assembly (for Top and Dual Fill Models)
Upper Screened Intake Assembly
(Top / Dual Fill Models)
Upper Head Valve Assembly Pump Housing
Internal Float Assembly
Bottom Plug (Top Fill Model)
Bottom Intake (Bottom / Dual Fill Models)
Figure 1
Fluid Discharge Assembly
Control Rod
Center Pipe
5
Chapter 2: System Installation
Top Fill
Attach the hoses to the proper barbed fittings (see figure 2, page 7). Ensure that all hoses are installed securely and completely (Fluid intake assembly not shown).
Ensure the eyebolt is threaded all the way to the fixed jam nut, and is securely tightened.
Attach the pump hanging cable to the eyebolt; ensuring attachment method is secure and tight. The Auto-Reclaimer can now be lowered into the recovery well. The top fill Auto-Reclaimer is initially lowered into the well where the top inlet is submerged below static groundwater conditions. This allows floating product to enter through the top inlet to fill the housing and be pumped to the surface (see figure 3, page 11).
Bottom Fill
Attach the air inlet, product discharge, and the air exhaust hoses to the proper barbed fittings (see figure 2, page 7).
Attach the pump hanging cable to the eyebolt; ensuring attachment method is secure and tight. The Auto-Reclaimer can now be lowered into the recovery well. The bottom fill Auto-Reclaimer is initially lowered into the well where the bottom inlet is submerged well below static groundwater conditions (see figure 4, page 12.
Ensure the eyebolt is threaded all the way to the
fixed jam nut, and is securely tightened.
6
Figure 2
Fluid Discharge
Air Supply
Air Exhaust (Vent)
Hanger Eyebolt
7
Dual Fill
Attach the hoses to the proper barbed fittings (see figure 2, page 7). Ensure that all hoses are installed securely and completely. Ensure the eyebolt is threaded all the way to the fixed jam nut, and securely tightened. Attach the pump hanging cable to the eyebolt; ensuring attachment method is secure and tight. The Auto-Reclaimer can now be lowered into the recovery well. The Dual (top / bottom) fill Auto-Reclaimer is initially lowered into the well where the top inlet is submerged below static groundwater conditions. This allows floating product to enter through both the top and bottom inlets to fill the housing and be pumped to the surface.
8
Chapter 3: System Operation
Compressed air is utilized in this system as an on
demand supply. Typically, .5 cubic foot of air is
necessary per gallon of liquid pumped.
Top Fill
The Auto-Reclaimer is placed in a recovery well with the top inlet submerged below static groundwater. Provided with a regulated air supply, the Auto-Reclaimer cyclically fills and empties. As the pump fills, the internal float assembly rises until it comes in contact with an upper stop that is connected to a mechanical rocker assembly. The rocker assembly shifts and simultaneously opens the air supply valve. The resulting effect is air pressure builds within the pump housing and displaces the fluids up and out of the pump through the discharge ball check valve. As the pump discharge cycle progresses, the float assembly falls. The float assembly contacts the lower stop, which triggers the rocker assembly, again shifting, thus closing the air supply valve and opening the air exhaust valve. The pressurized air exits out of the air exhaust tube, allowing the pump to refill and begin a new cycle. This cyclic operation continues automatically as fluid is drawn into the well.
Bottom Fill
The Bottom Fill Auto-Reclaimer is placed in a recovery well with the bottom intake submerged below static groundwater. Provided with a regulated air supply, the Auto-Reclaimer cyclically fills and empties. As the pump fills, the internal float assembly rises until it comes in contact with an upper stop that is connected to a mechanical rocker assembly. The rocker assembly shifts and simultaneously opens the air supply valve. The resulting effect is air pressure builds within the pump housing and displaces the fluids up and out of the pump through the discharge ball check valve. As the pump discharge cycle progresses, the float assembly falls. The float assembly contacts the lower stop, which
9
triggers the rocker assembly, again shifting, thus closing the air supply valve and opening the air exhaust valve. The pressurized air exits out of the air exhaust tube, allowing the pump to refill and begin a new cycle. This cyclic operation continues automatically as fluid is drawn into the well. The Auto-Reclaimer will ultimately catch up to the recharge rate of the well, (see specifications section, maximum flow rate). The fluid level will be maintained at the minimum activation level (see specifications), and the Auto-Reclaimer will pump at the rate equal to the recharge rate of the well.
Dual Fill
The Top/Bottom fill Auto-Reclaimer is placed in a recovery well with the top inlet submerged below static groundwater. Provided with a regulated air supply, the Auto-Reclaimer cyclically fills and empties. As the pump fills, the internal float assembly rises until it comes in contact with an upper stop that is connected to a mechanical rocker assembly. The rocker assembly shifts and simultaneously opens the air supply valve. The resulting effect is air pressure builds within the pump housing and displaces the fluids up and out of the pump through the discharge ball check valve. As the pump discharge cycle progresses, the float assembly falls. The float assembly contacts the lower stop, which triggers the rocker assembly, again shifting, thus closing the air supply valve and opening the air exhaust valve. The pressurized air exits out of the air exhaust tube, allowing the pump to refill and begin a new cycle. This cyclic operation continues automatically as fluid is drawn into the well.
10
Figure 3
11
Figure 4
12
Chapter 4: System Maintenance
Maintenance Procedures Every 3-4 months or when deemed necessary, depending on fluids being pumped, the Auto-Reclaimer should be removed from the well and cleaned inside and out. This may be accomplished using an industrial cleaner, such as phosphate free detergent or Simple Green. The following areas should be examined: Float Assembly - Check for loose screws on float plates. Compression Springs - Check for proper spring geometry. Air Pressure Valve - Verify gap, adjust if necessary. Exhaust Valve - Verify gap, adjust if necessary. O-Rings - Visually inspect for damage. Stop Collar - Verify location distance from female spring guide (see figure below).
Figure 5
Pump does not require clean dry air to operate. However, using dirty particulate filled air will increase maintenance frequency.
13
Chapter 5: System Troubleshooting
Problem: Pump does not discharge fluid to the surface. Solutions: 1) Ensure air pressure is adequate enough. –
(See specifications section, min operating pressure example: .43 psi per ft. of static head pressure)
2) Inlet screen is clogged –
Clean screen 3) Inlet pipe plug is clogged –
Clear, Clean plug 4) Air exhaust vent hose is clogged –
Clear vent hose 5) Hoses are kinked or cut –
Replace hoses
14
Chapter 6: System Specifications
48
” G
EO
TE
CH
1
.6
6 A
UT
O-R
EC
LA
IM
ER
ST
AIN
LE
SS
ST
EE
L,
PT
FE
, A
ce
tal, V
ITO
N
ST
AIN
LE
SS
ST
EE
L
48
” B
OT
TO
M L
OA
DIN
G
FIX
ED
IN
TA
KE
CO
NT
RO
LL
ER
LE
SS
PO
SIT
IVE
AIR
DIS
PL
AC
EM
EN
T
1.6
6 in.
(4.2
2cm
.)
54
.7 in.
(13
9.0
cm
.)
9.5
lbs.
(4.3
kg
.)
25
0 f
t. (
15
2.4
m.)
2.0
in
. (5
.08
cm
.)
5-2
75
psi. (
.3-1
8.9
ba
r)
1 p
si. (
.07 b
ar)
ab
ove s
tatic h
ea
d
.4-1
.3 s
cf /
ga
l (3
.0 /
9.7
lite
rs a
ir/lite
rs (
flu
id)
(se
e a
ir c
on
su
mp
tion
cu
rve)
.7 S
pG
(g
r/cc)
.11
ga
l. (
.42
lite
rs)
3.0
0 g
pm
. (1
1.3
6 lpm
.) @
20
ft.
2
.75
gp
m. (1
0.4
1 lpm
.) @
20
ft.
s
ub
merg
en
ce @
100
psi
su
bm
erg
en
ce
@ 1
00
psi
38
.0 in.
(96
.5cm
.)
3
8.0
in
. (9
6.5
cm
.)
ST
AIN
LE
SS
ST
EE
L (
BA
RB
TY
PE
)
1/2
" X
3/8
” M
PT
1/4
” X
1/8
” M
PT
1/4
” X
1/8
” M
PT
22
0°
F T
OP
TE
MP
ER
AT
UR
E F
OR
HD
PE
48
” D
UA
L (
TO
P /
BO
TT
OM
LO
AD
ING
FIX
ED
IN
TA
KE
CO
NT
RO
LL
ER
LE
SS
PO
SIT
IVE
AIR
DIS
PL
AC
EM
EN
T
1.6
6 in.
(4.2
2cm
.)
56
.3 in.
(14
3.0
cm
.)
10
lb
s.
(4.5
kg
.)
25
0 f
t. (
15
2.4
m.)
2.0
in
. (5
.08
cm
.)
CO
NS
TR
UC
TIO
N M
AT
ER
IAL
S
HO
US
ING
MA
TE
RIA
L
CO
NF
IGU
RA
TIO
N
PU
MP
TY
PE
OU
TS
IDE
DIA
ME
TE
R
LE
NG
TH
WE
IGH
T
MA
X.
RA
TE
D D
EP
TH
MIN
. W
EL
L I
D
OP
ER
AT
ING
PR
ES
SU
RE
R
AN
GE
MIN
. O
PE
RA
TIN
G P
RE
SS
UR
E
AIR
CO
NS
UM
PT
ION
MIN
. L
IQU
ID D
EN
SIT
Y
VO
LU
ME
/ C
YC
LE
MA
XIM
UM
FL
OW
RA
TE
MIN
IMU
M A
CT
IVA
TIO
N L
EV
EL
FIT
TIN
GS
HO
SE
SIZ
ES
FL
UID
DIS
CH
AR
GE
AIR
SU
PP
LY
AIR
EX
HA
US
T
TE
MP
ER
AT
UR
E S
PE
CIF
ICA
TIO
NS
Figure 6
15
Figure 7
GE
OT
EC
H 1
.66 A
UT
O-R
EC
LA
IME
R4
8"
To
p L
oa
din
g F
ixe
d I
nta
ke
(1/2
" ID
Flu
id D
isc
ha
rge
Ho
se
)
0.0
0
0.2
0
0.4
0
0.6
0
0.8
0
1.0
0
1.2
0
1.4
0
1.6
0
02
55
07
51
00
12
51
50
17
52
00
22
52
50
PU
MP
DE
PT
H (
FT
)
GPM
48”
GE
OT
EC
H 1
.66 A
UT
O-R
EC
LA
IME
R
ALL C
ALC
UL
AT
ION
S B
AS
ED
ON
MO
DE
L G
EO
1.6
6
W / M
INIM
UM
10’ S
UB
ME
RG
EN
CE
OF
PU
MP
HE
AD
48”
TO
P L
OA
DIN
G F
IXE
D I
NT
AK
E
(1/2
” ID
Flu
id D
ischarg
e H
ose)
NO
TE
:
SP
EC
IFIC
GR
AV
ITY
AN
D V
ISC
OS
ITY
WIL
L A
LT
ER
LIS
TE
D S
PE
CIF
ICA
TIO
NS
45 P
SI
70 P
SI
100 P
SI
16
Figure 8
0.0
0
0.5
0
1.0
0
1.5
0
2.0
0
2.5
0
02
55
07
51
00
12
51
50
17
52
00
22
52
50
PU
MP
DE
PT
H (
FT
)
GPM
48”
GE
OT
EC
H 1
.66 A
UT
O-R
EC
LA
IME
R
ALL C
ALC
UL
AT
ION
S B
AS
ED
ON
MO
DE
L G
EO
1.6
6
W / M
INIM
UM
10’ S
UB
ME
RG
EN
CE
OF
PU
MP
HE
AD
48”
BO
TT
OM
LO
AD
ING
FIX
ED
IN
TA
KE
(1/2
” ID
Flu
id D
ischarg
e H
ose)
45 P
SI
70 P
SI
100 P
SI
NO
TE
:
SP
EC
IFIC
GR
AV
ITY
AN
D V
ISC
OS
ITY
WIL
L A
LT
ER
LIS
TE
D S
PE
CIF
ICA
TIO
NS
17
Figure 9
GE
OT
EC
H 1
.66 A
UT
O-R
EC
LA
IME
R4
8"
Du
al
Lo
ad
ing
Fix
ed
In
tak
e(1
/2" ID
Flu
id D
isc
ha
rge
Ho
se
)
0.0
0
0.5
0
1.0
0
1.5
0
2.0
0
2.5
0
3.0
0
02
55
07
51
00
12
51
50
17
52
00
22
52
50
de
pth
GPM
48”
GE
OT
EC
H 1
.66 A
UT
O-R
EC
LA
IME
R
ALL C
ALC
UL
AT
ION
S B
AS
ED
ON
MO
DE
L G
EO
1.6
6
W / M
INIM
UM
10’ S
UB
ME
RG
EN
CE
OF
PU
MP
HE
AD
48”
DU
AL L
OA
DIN
G F
IXE
D IN
TA
KE
(1/2
” ID
Flu
id D
ischa
rge H
ose)
45 P
SI
70 P
SI
100 P
SI
NO
TE
:
SP
EC
IFIC
GR
AV
ITY
AN
D V
ISC
OS
ITY
WIL
L A
LT
ER
LIS
TE
D S
PE
CIF
ICA
TIO
NS
18
Figure 10
48"G
EO
TEC
H 1
.66 A
UT
O-R
EC
LA
IMER
AIR
CO
NS
UM
PT
ION
CU
RV
ES
1/2
" ID
FL
UID
DIS
CH
AR
GE H
OS
E
0.0
00
0.2
00
0.4
00
0.6
00
0.8
00
1.0
00
1.2
00
1.4
00
025
50
75
100
125
150
175
200
225
250
DEP
TH
OF P
UM
P IN
WEL
L
MA
XIM
UM
AIR
US
E IN
ST
AN
DA
RD
CU
BIC
FEET
(SC
F)
PER
GA
LL
ON
PU
MP
ED
SCF/gal
45 p
si
70 p
si
100 p
si
48”
GE
OT
EC
H 1
.66 A
UT
O-R
EC
LA
IME
R
AIR
CO
NS
UM
PT
ION
CU
RV
ES
1/2
” ID
FLU
ID D
ISC
HA
RG
E H
OS
E
DE
PT
H O
F P
UM
P I
N W
EL
L
MA
XIM
UM
AIR
US
E IN
ST
AN
DA
RD
CU
BIC
FE
ET
(SC
F)
PE
R G
ALLO
N P
UM
PE
D
45 P
SI
70 P
SI
100 P
SI
19
Chapter 7: Replacement Parts List
Parts List Parts Description 11150019 Ball, SS6 16600110 Spring, Compression, SS6 16600133 F, Bolt, Eye, SS4 16600160 Set Screw, Dog PT. 17200072 F, Hosebarb, SS6 (Air) 17200072 F, Hosebarb, SS6 (Vent) 17500082 Ball, SS6 17500084 Ball, TFE 26600036 Lower Stop 26600061 Housing, Outer, SS, 1.66 Auto 26600071 Head, Bottom Inlet, 1.66B Auto 26600072 Cap, Bottom Inlet, 1.66B Auto 26600078 Seat, Pres Valve, SS, 1.66 Auto 26600079 Seat, Vent Valve, SS, 1.66 Auto 26600083 Screen, Inlet, SS, 1.66 Auto 26600084 Hosebarb, SS, 1/2” x 3/8” MPT (Discharge) 26600086 Rod, Control, SS4, 1.66 Auto 48” 26600130 Stop Collar 56600025 Assy, Float, 1.66 Auto 16600165 Manual
20
The Warranty
For a period of one (1) year from date of first sale, product is warranted to be free from defects in materials and workmanship. Geotech agrees to repair or replace, at Geotech’s option, the portion proving defective, or at Geotech’s option to refund the purchase price thereof. Geotech will have no warranty obligation if the product is subjected to abnormal operating conditions, accident, abuse, misuse, unauthorized modification, alteration, repair, or replacement of wear parts. User assumes all other risk, if any, including the risk of injury, loss, or damage, direct or consequential, arising out of the use, misuse, or inability to use this product. User agrees to use, maintain and install product in accordance with recommendations and instructions. User is responsible for transportation charges connected to the repair or replacement of product under this warranty.
Equipment Return Policy
A Return Material Authorization number (RMA #) is required prior to return of any equipment to our facilities, please call 800 number for appropriate location. An RMA # will be issued upon receipt of your request to return equipment, which should include reasons for the return. Your return shipment to us must have this RMA # clearly marked on the outside of the package. Proof of date of purchase is required for processing of all warranty requests. This policy applies to both equipment sales and repair orders. FOR A RETURN MATERIAL AUTHORIZATION, PLEASE CALL OUR SERVICE DEPARTMENT AT 1-800-833-7958 Model Number: ________________ Serial Number: ________________ Date: ________________
Equipment Decontamination
Prior to return, all equipment must be thoroughly cleaned and decontaminated. Please make note on RMA form, the use of equipment, contaminants equipment was exposed to, and decontamination solutions/methods used. Geotech reserves the right to refuse any equipment not properly decontaminated. Geotech may also choose to decontaminate equipment for a fee, which will be applied to the repair order invoice.
Geotech Environmental Equipment, Inc
2650 East 40th
Avenue Denver, Colorado 80205
(303) 320-4764 ● (800) 833-7958 ● FAX (303) 322-7242
email: [email protected] website: www.geotechenv.com