Geometrics, Inc. 45 years experience in making geophysical instrumentsSan Jose, California USADouglas Groom, Director of Geoelectrical Products

Geode EM3DNew geophysical instrument for High-resolution CSAMT surveys

(controlled source audio magnetotellurics)

Minex Central Asia, April 2014Astana, Kazakhstan

Geode EM3D FeaturesWhat is it?

• Distributed network of up to forty EM receivers each have six channels for total 240 EM channels

• Each receiver configurable for up to six telluric (E-field) channels and up to three magnetic (H-field) channels

• Durable metal enclosure. • Low noise front end as low as 10 nV/rtHz• Low distortion front end• Automatic calibration in the field• Automatic contact resistance measurement in the field• Much more

Highlights

• Synchronized electric and magnetic field measurements for CSAMT, AMT, and more

• Synchronized by GPS to CSAMT transmitter• Rugged instrumentation• Reliable network architecture• Backed by 45 years of experience in

geophysical instrument manufacture

Geode EM3D 24-Channel Network20 E – 4 H Channels

BenefitsWhy use it?

• High-density 3-D data sets for complete characterization of your mining prospect

• Rapid data collection with all channels GPS-synchronized to a single transmitter

• Flexible spacing of H-field sensors to maximize resolution yet minimize cost

• Scalable network from 6 channels up to 240 channels• Full tensor CSAMT using two transmitter polarizations• Automatic contact resistance measurement for better data

quality• In-field calibration for more accurate measurement• Future AMT, IP, Resistivity modules available

Geode EM3D Single Receiver

High-resolution, high-density EM data with many sounding stations at the same

time (simultaneous data acquisition).• Traditional CSAMT uses a separate setup for each sounding.• For example, for 50 traditional CSAMT stations (soundings)

the transmitter must be run fifty times and the station moved 50 times. Typically 30 minutes to one hour transmitter run time for each station meaning 50 hours of transmitter time for the survey, not including setup time.

• Geode EM3D allows a single setup of all stations and one transmitter run for acquisition of all 50 sounding at the same time (simultaneous acquisition). That is only 30 to 60 minutes in total for all 50 stations.

Orienting and leveling magnetic coils can be the most time consuming process in setting up a station

Geode EM3D offers flexibility in the use of H-field magnetic sensor coils

• Saves time: Traditional CSAMT requires burying coils for every sounding. Each time the station is moved the coils are reburied. Geode EM3D network allows using magnetic coils on one receiver to be used for multiple soundings on other receivers so fewer coils need to be buried.

• Improves efficiency: Operator can choose the optimal number of magnetic coils for the survey needs. For example H-field measurements can be used for every two E-field measurements, or maybe only every six, ten, or more E-field measurements, depending on the complexity of the geology and the requirements of the survey.

• Improves data quality: Using multiple Hy and Hx on different receivers, at different locations simultaneously, allows local referencing to improve data quality.

Flexible networking

Easily scalable system from single-receiver 6-channel system to 40-receiver, 240-channel system

• Maximum flexibility in survey setup. Each receiver can be any combination of E and H up to six channels, such as:

• 3E/3H• 4E/2H• 5E/1H• 6E

Field setup and channel parametersNote automatic contact resistance for every E-field dipole

GeodEM2010 Acquisition MenuNote “Measure Contact Resistance” and “Measure AC & DC Level”

• Contact resistance measured on automatically on all electrode channels. AC and DC noise level measured automatically.

China GeoTech Beijing

• Introduction of multi-node Geode EM3D to Chinese

120-Channel, 20-Receiver setup on bench

Exhibit interest

In-field screen display of test signal into 120 channel Geode EM3D

Better results with full tensor CSAMT

• Traditional CSAMT only does scalar (Ex/HY) impedance calculations. The Geode EM3D can easily do full-tensor measurements (Ex/Hy and Ey/Hx) using multiple polarizations from the controlled-source transmitter.

Geode EM3D field test approximately 100 km north of Beijing

• Four receiver network consisting of 20 channels used.

• Four magnetic (H-field) channels• Sixteen electric (E-field) channels• Four channels not deployed

Phoenix T-3 3 kW transmitter

Transmitter + Controller + Generator + PDA Monitor

Planting the transmitter dipole

Grounding transmitter dipole with metal plates and stakes

Chinese made 30 kW transmitter + controller + power supplies + junction

boxes + monitoring gear

Two 15 kW generators for 30 kW Chinese transmitter

Set up frequency scheduler

CSAMT field data16 channels at 8 Hz with 1.5 kW transmitter at 12.5 km distance

CSAMT field data16 channels at 8 Hz with transmitter at 12.5 km

distance

Real-time CSAMT impedance curves for six soundings in field

CSAMT and AMT now with future, IP, resistivity and other methods in future

• The first Geode EM3D product is controlled source audio magnetotellurics (CSAMT). Future products plans include AMT (natural-field audio magnetotellurics), induced polarization (IP) resistivity and other geoelectrical techniques.

Setting parameters for AMT acquisitionNote that seven channels defines tensor site

• Ex, Ey, Hx, Hy, Hz, Hx2 and Hy2 for local reference

AMT real-time times series field display (natural field with no transmitter)

AMT

AMT

Real-time field data processing

GEM3D receiver with coil cables, porous pot, dipole cables, battery, Ethernet cable

Retrieving 250-m Ethernet cables at end of day

System Configurations

• 1. Single Node– One GeodeEM box used for AMT/CSAMT/IP with various

configurations 6E, 5E1H, 4E2H, 3E3H• 2. “Typical” Small Networked System– Four Geode EM3D receivers is the base network, with

various configurations possible• 3. “Maximum” Networked System– 40 GeodeEM boxes, i.e. 240 channels. – 20 Geode EM networ of 110 on display in Laurel

Geophysical booth in exhibition hall.