Geometric Symbols
description
Transcript of Geometric Symbols
![Page 1: Geometric Symbols](https://reader031.fdocuments.in/reader031/viewer/2022020717/5681596b550346895dc6aba3/html5/thumbnails/1.jpg)
Geometric SymbolsGeometric Symbols
Geometric Dimensions and Geometric Dimensions and TolerancesTolerances
![Page 2: Geometric Symbols](https://reader031.fdocuments.in/reader031/viewer/2022020717/5681596b550346895dc6aba3/html5/thumbnails/2.jpg)
Geometric Geometric SymbolsSymbols
![Page 3: Geometric Symbols](https://reader031.fdocuments.in/reader031/viewer/2022020717/5681596b550346895dc6aba3/html5/thumbnails/3.jpg)
How is GTD information Conveyed on a Drawing?
• Geometric Characteristics are Specified Through Symbols in a geometric feature control frame
• Modifiers and Tolerances Expand and Clarify the Symbols to Ensure Drawings are Unambiguous
![Page 4: Geometric Symbols](https://reader031.fdocuments.in/reader031/viewer/2022020717/5681596b550346895dc6aba3/html5/thumbnails/4.jpg)
Geometric Characteristics and Symbols 1. FORM
![Page 5: Geometric Symbols](https://reader031.fdocuments.in/reader031/viewer/2022020717/5681596b550346895dc6aba3/html5/thumbnails/5.jpg)
Geometric Characteristics and Symbols 2. Profile , 3. Orientation
![Page 6: Geometric Symbols](https://reader031.fdocuments.in/reader031/viewer/2022020717/5681596b550346895dc6aba3/html5/thumbnails/6.jpg)
Geometric Characteristics and Symbols 4. Runout , 5. Location
![Page 7: Geometric Symbols](https://reader031.fdocuments.in/reader031/viewer/2022020717/5681596b550346895dc6aba3/html5/thumbnails/7.jpg)
Using Notes
![Page 8: Geometric Symbols](https://reader031.fdocuments.in/reader031/viewer/2022020717/5681596b550346895dc6aba3/html5/thumbnails/8.jpg)
Using Symbols
![Page 9: Geometric Symbols](https://reader031.fdocuments.in/reader031/viewer/2022020717/5681596b550346895dc6aba3/html5/thumbnails/9.jpg)
GEOMETRIC FEATURE CONTROL FRAME
![Page 10: Geometric Symbols](https://reader031.fdocuments.in/reader031/viewer/2022020717/5681596b550346895dc6aba3/html5/thumbnails/10.jpg)
FLATNESS
![Page 11: Geometric Symbols](https://reader031.fdocuments.in/reader031/viewer/2022020717/5681596b550346895dc6aba3/html5/thumbnails/11.jpg)
FLATNESS
• The condition of a surface having all points in one plane.
• A flatness tolerance specifies a zone defined by 2 parallel planes.
![Page 12: Geometric Symbols](https://reader031.fdocuments.in/reader031/viewer/2022020717/5681596b550346895dc6aba3/html5/thumbnails/12.jpg)
Flatness
![Page 13: Geometric Symbols](https://reader031.fdocuments.in/reader031/viewer/2022020717/5681596b550346895dc6aba3/html5/thumbnails/13.jpg)
Flatness
![Page 14: Geometric Symbols](https://reader031.fdocuments.in/reader031/viewer/2022020717/5681596b550346895dc6aba3/html5/thumbnails/14.jpg)
STRAIGHTNESS
• Straightness is the condition where all the points on a surface or an axis are in a straight line
• A straightness tolerance specifies a zone within which the surface or axis must lie
![Page 15: Geometric Symbols](https://reader031.fdocuments.in/reader031/viewer/2022020717/5681596b550346895dc6aba3/html5/thumbnails/15.jpg)
STRAIGHTNESS
![Page 16: Geometric Symbols](https://reader031.fdocuments.in/reader031/viewer/2022020717/5681596b550346895dc6aba3/html5/thumbnails/16.jpg)
ROUNDNESS OF A CYLINDER• Roundness or circularity is the condition of a
cylindrical surface in which all points on the surface intersected by any plane perpendicular to a common axis equidistant from the axis.
![Page 17: Geometric Symbols](https://reader031.fdocuments.in/reader031/viewer/2022020717/5681596b550346895dc6aba3/html5/thumbnails/17.jpg)
![Page 18: Geometric Symbols](https://reader031.fdocuments.in/reader031/viewer/2022020717/5681596b550346895dc6aba3/html5/thumbnails/18.jpg)
• CIRCULARITY • Or Roundness tolerance specifies a zone
bounded by two concentric circles within which the measured surface must lie
![Page 19: Geometric Symbols](https://reader031.fdocuments.in/reader031/viewer/2022020717/5681596b550346895dc6aba3/html5/thumbnails/19.jpg)
CIRCULARITY of A SPHERE
![Page 20: Geometric Symbols](https://reader031.fdocuments.in/reader031/viewer/2022020717/5681596b550346895dc6aba3/html5/thumbnails/20.jpg)
• The Periphery at any cross section passing through a common center must be within the specified tolerance of size and must be between two concentric circles
![Page 21: Geometric Symbols](https://reader031.fdocuments.in/reader031/viewer/2022020717/5681596b550346895dc6aba3/html5/thumbnails/21.jpg)
CYLINDRICITYCYLINDRICITY Cylindricity is the condition Cylindricity is the condition
where all points of a surface of where all points of a surface of revolution are equidistant from revolution are equidistant from a common axisa common axis
cylindricity tolerance specifies a cylindricity tolerance specifies a zone bounded by 2 concentric zone bounded by 2 concentric cylinders within which the cylinders within which the measured surface must lie.measured surface must lie.
![Page 22: Geometric Symbols](https://reader031.fdocuments.in/reader031/viewer/2022020717/5681596b550346895dc6aba3/html5/thumbnails/22.jpg)
CYLINDRICITYCYLINDRICITY
![Page 23: Geometric Symbols](https://reader031.fdocuments.in/reader031/viewer/2022020717/5681596b550346895dc6aba3/html5/thumbnails/23.jpg)
CYLINDRICITYCYLINDRICITY
![Page 24: Geometric Symbols](https://reader031.fdocuments.in/reader031/viewer/2022020717/5681596b550346895dc6aba3/html5/thumbnails/24.jpg)
PROFILE TOLERANCE• PROFILE OF A LINE:• The tolerance zone established by the profile of
a line tolerance is two dimensional extending along the length of the considered feature
![Page 25: Geometric Symbols](https://reader031.fdocuments.in/reader031/viewer/2022020717/5681596b550346895dc6aba3/html5/thumbnails/25.jpg)
PROFILE TOLERANCE• PROFILE OF A SURFACE:• The established tolerance zone is three
dimensional extending along the length and width of the considered feature
![Page 26: Geometric Symbols](https://reader031.fdocuments.in/reader031/viewer/2022020717/5681596b550346895dc6aba3/html5/thumbnails/26.jpg)
ORIENTATION TOLERANCE• PERPENDICULARITY
• Is a condition of a line, center line, axis or surface at a right angle to a datum plan or axis.
• Perpendicularity tolerance specifies one of the following:
![Page 27: Geometric Symbols](https://reader031.fdocuments.in/reader031/viewer/2022020717/5681596b550346895dc6aba3/html5/thumbnails/27.jpg)
PERPENDICULARITY
• 1. A zone defined by 2 parallel planes perpendicular to a datum plane or axis. In the example shown,
• The surface of the feature must lie within this zone which is 0.15mm wide and at right angles to datum A.
![Page 28: Geometric Symbols](https://reader031.fdocuments.in/reader031/viewer/2022020717/5681596b550346895dc6aba3/html5/thumbnails/28.jpg)
• 2. A zone defined by 2 parallel planes perpendicular to the datum axis.
• In this example, the axis of the hole must lie within the zone which is 0.3mm wide and at right angles to datum axis A. The feature axis must also be within the tolerance of location.
![Page 29: Geometric Symbols](https://reader031.fdocuments.in/reader031/viewer/2022020717/5681596b550346895dc6aba3/html5/thumbnails/29.jpg)
ORIENTATION TOLERANCE
![Page 30: Geometric Symbols](https://reader031.fdocuments.in/reader031/viewer/2022020717/5681596b550346895dc6aba3/html5/thumbnails/30.jpg)
ANGULARITY
• Angularity is the condition of a surface or axis at a specified angle (other than 9O) from a datum plane or axis.
![Page 31: Geometric Symbols](https://reader031.fdocuments.in/reader031/viewer/2022020717/5681596b550346895dc6aba3/html5/thumbnails/31.jpg)
• The tolerance zone is defined by 2 parallel planes at the specified basic angle from a datum plane or axis. The surface or axis of the considered feature must lie within this zone.
![Page 32: Geometric Symbols](https://reader031.fdocuments.in/reader031/viewer/2022020717/5681596b550346895dc6aba3/html5/thumbnails/32.jpg)
• In the example all points of the surface must
lie within the 0.5mm wide tolerance zone.
![Page 33: Geometric Symbols](https://reader031.fdocuments.in/reader031/viewer/2022020717/5681596b550346895dc6aba3/html5/thumbnails/33.jpg)
• Parallelism is the condition of a surface or axis equidistant at all points from a datum plane or axis.
• Parallelism tolerance specifies one of the following:
Parallelism
![Page 34: Geometric Symbols](https://reader031.fdocuments.in/reader031/viewer/2022020717/5681596b550346895dc6aba3/html5/thumbnails/34.jpg)
• 1. A zone defined by 2 planes or lines parallel to a datum plane or axis.
![Page 35: Geometric Symbols](https://reader031.fdocuments.in/reader031/viewer/2022020717/5681596b550346895dc6aba3/html5/thumbnails/35.jpg)
• In this example, the surface of the feature must lie within 2 planes 0.25mm y apart which are parallel to datum A.
![Page 36: Geometric Symbols](https://reader031.fdocuments.in/reader031/viewer/2022020717/5681596b550346895dc6aba3/html5/thumbnails/36.jpg)
• 2. A cylindrical tolerance zone whose axis is parallel to a datum axis.
![Page 37: Geometric Symbols](https://reader031.fdocuments.in/reader031/viewer/2022020717/5681596b550346895dc6aba3/html5/thumbnails/37.jpg)
• In this example the axis of the hole must lie within a cylindrical zone of 0.3mm diameter parallel to datum A.
![Page 38: Geometric Symbols](https://reader031.fdocuments.in/reader031/viewer/2022020717/5681596b550346895dc6aba3/html5/thumbnails/38.jpg)