Genevac Accessories and Spares - SP Scientific...Rocket Sample Holders 04-8931 Issue 1-14 October...
Transcript of Genevac Accessories and Spares - SP Scientific...Rocket Sample Holders 04-8931 Issue 1-14 October...
Genevac
Accessories and Spares
For Rocket™ Synergy Evaporators
Original instructions in English Part number 04-8931 Issue 1-14 October 2015
Contents
Introduction ......................................................................................................................... 2 Maintenance of sample holders .................................................................................................. 2 Limitations of use ....................................................................................................................... 3 Colour variation of surface finish................................................................................................. 3
Rotors ................................................................................................................................... 4 Flask rotor .................................................................................................................................. 4 Bowl rotor ................................................................................................................................... 4 Rotor Spares .............................................................................................................................. 5 Rotor accessories ....................................................................................................................... 7
Sample Holders for Flask Rotors ....................................................................................... 8 SampleGenie4 ............................................................................................................................ 8 SampleGenie4 spares ................................................................................................................. 9 GC Vial System2 ....................................................................................................................... 12 GC Vial System2 spares ........................................................................................................... 13 Standard Flask ......................................................................................................................... 15 Standard flask spares ............................................................................................................... 15 ASE Tube Puck ........................................................................................................................ 16 ASE Tube Puck spares ............................................................................................................. 16 Flip-Flop ................................................................................................................................... 17 Flip-Flop Spares ....................................................................................................................... 18
Accessories ....................................................................................................................... 20 Sampleholder accessories........................................................................................................ 20 Infinity Trolley ........................................................................................................................... 21
General Spares .................................................................................................................. 22 Main lid seal ............................................................................................................................. 22 Sample viewing window ........................................................................................................... 22 Waste solvent container ........................................................................................................... 22 Lid joint coupling (for feed system) ........................................................................................... 22 Feed hoses .............................................................................................................................. 23 Fittings for coolant, drain and exhaust hoses ............................................................................ 23
Quick Reference ................................................................................................................ 24 Part numbers ............................................................................................................................ 24 Amendment control .................................................................................................................. 25
Rocket Sample Holders
2 04-8931 Issue 1-14 October 2015
Introduction
Genevac produce a range of sample holders and accessories that can be used to enhance the performance and increase the flexibility of Rocket™ Synergy and Rocket 4D Synergy high speed evaporation systems. Sample holders are manufactured using high quality materials such as boroscilicate glass and high grade alluminium. Where applicable, seals can be specified in low leachable viton or in highly resistant perfluoroelastomer.
Maintenance of sample holders
The Rocket evaporator controls pressure levels in inner and outer vacuum chambers independently and sample holders form part of the seal between these chambers; it is therefore vitaly important that a perfect seal is formed around each of the sample holders. To achieve this, the sample holders must be maintained in good condition and must be used correctly. Sample holders must be clean and free from imperfections around the area of the sealing surfaces; chips, scratches or labels applied to the flasks may cause leaks which can slow down the evaporation process. Refer to the Genevac Rocket™ Sample Holders User Manual for advice on day to day maintenance and use of the Rocket sample holders.
Rocket Sample Holders
04-8931 Issue 1-14 October 2015 3
Limitations of use
This brochure contains informantion on a range of accessories and sample holders that are intended for use with Rocket Synergy and Rocket 4D Syenrgy evaporators. Some of the accessories and sample holders are also compatible with earlier (“pre-Synergy”) Rocket evaporators, although limitations may apply. Where limitations do apply, they shall be indicated as shown in the following example:
For use with Rocket 4D Synergy feed systems only In this example, the accessory must not be used with any system other than that which is specified.
Colour variation of surface finish
For some components the colouring of surface finish may vary slightly from batch to batch; for instance, one batch of vial adapters may appear darker than another. Where this occurs it does not affect the performance or integrity of the component.
Rocket Sample Holders
4 04-8931 Issue 1-14 October 2015
Rotors
Flask rotor
Part number
Flask rotor 70-1734/S
Details Six position flask rotor assembly for Rocket Synergy or Rocket 4D Synergy includes inner lid and six blanking plugs.
Bowl rotor - batch
Part number
Bowl rotor - batch 70-1820/S
Details
Five litre bowl rotor for Rocket 4D Synergy or Rocket Synergy, includes batch (non-feed) inner lid, batch baffles, lifting handles and USB data-key with Rocket Synergy batch methods.
Bowl rotor - feed
Part number
Bowl rotor - feed 70-1752/S
Details
Five litre bowl rotor for Rocket 4D Rocket 4D Synergy, includes feed inner lid, feed baffle, lifting handles and USB data-key with Rocket Synergy feed methods.
Rocket Sample Holders
04-8931 Issue 1-14 October 2015 5
Rotor Spares
Part number
Inner lid 70-1548/S Non-feed
Details Inner lid for flask or non-feed bowl rotor.
Part number
Inner lid 70-1547/S Feed
Details Inner lid for bowl rotor For use with Rocket 4D Synergy feed systems only.
Part number
Batch baffle 70-1549/S
Details Batch baffle for bowl rotor. Set of two.
Part number
Feed baffle 04-7652/S
Details Single feed baffle for bowl rotor.
Rocket Sample Holders
6 04-8931 Issue 1-14 October 2015
Part number
Inner lid seal 04-7448/S
Details Seal for inner lid, fits flask rotor and bowl rotor.
Part number
Flask seals 70-1180
Details Flask seals used on Rocket Synergy flask rotor and pre-Synergy Rocket. Set of six.
Part number
O-ring 04-5676
Details O-ring (viton) for rotor hub.
Seal
Cap
Part number
Seal 70-1556/S
Details Seal kit (consisting of plug and O-ring) for bowl rotor pouring spout.
Part number
Cap 70-1557/S
Details Cap for bowl rotor pouring spout.
Rocket Sample Holders
04-8931 Issue 1-14 October 2015 7
Rotor accessories
Part number
Lid stand 70-1186
Details Stand for inner lid. Suitable for use with all variants.
Part number
Lifting handles 70-1552/S
Details Lifting handles for Rocket Synergy bowl rotor. Set of two.
Part number
Blanking plug 70-2004/S
Details Blanking plug for flask rotor. Set of two.
Part number
Pouring stand 70-1798
Details Pouring stand. Suitable for use with bowl rotors that have a pouring spout.
Part number
Synergy methods 04-8844
Details
USB data key (flash-drive) containing method files for Rocket Synergy flask rotor and Rocket Synergy bowl rotor feed and batch methods.
Rocket Sample Holders
8 04-8931 Issue 1-14 October 2015
Sample Holders for Flask Rotors
SampleGenie4
Part number
SampleGenie4 70-1740
Details
SampleGenie4 flask assembly. For use in Rocket Synergy evaporators and Rocket 4D Synergy evaporators with optional flask rotor. Evaporators with serial numbers lower than RK0399 (pre-Synergy) require low speed upgrade. Set of six. Note: Excludes vial adapter, vial adapter pad and vial seal. When ordering: please select vial adapter from table below. Information on vial seals can be found in the following section: Sample Holder Spares.
Vial adapter
Details
Vial adapter for SampleGenie4. Note: Includes vial adapter pad. Set of six.
Max vial diameter ( mm) Vial length (mm) Seal required Part number
DG 15.3 36.5 to 41.5 One part 70-1766
DD 15.3 41.5 to 46.5 One part 70-1763
DJ 17.3 46.5 to 51.5 Two part 70-1769
DC 17.3 56.5 to 61.5 One part 70-1762
DH 20.8 39.5 to 44.5 Two part 70-1767
DF 23.3 42.5 to 47.5 Two part 70-1765
DI 23.2 54.5 to 59.5 Two part 70-1768
DE 23.3 66.5 to 71.5 Two part 70-1764
DB 28.0 56.5 to 61.5 Two part 70-1761
DA 28.0 66.5 to 71.5 Two part 70-1760
Rocket Sample Holders
04-8931 Issue 1-14 October 2015 9
SampleGenie4 spares
Part number
SG4 Flask 70-1741
Details Flask assembly only, for SampleGenie4. Set of six.
Part number
Collar pad 70-1743
Details Collar pad for SampleGenie4. Set of six.
Part number
Collar 70-1742
Details Collar for SampleGenie4. Set of six.
Part number
Holder 70-1744
Details Holder for SampleGenie4 vial adapter. Set of six
Rocket Sample Holders
10 04-8931 Issue 1-14 October 2015
Part number
Insert 70-1757
Details
Insert for SampleGenie4 two-part vial seal. For use with viton vial seal: 70-1758 or perfluoroelastomer vial seal: 70-1759. Set of six.
Part number
Vial seal 70-1758 Viton
Details
Viton seal for SampleGenie4 two-part vial seal. Requires insert: 70-1757. Set of six.
Note: Green mark in periphery indicates perfluoro.
Part number
Vial seal 70-1759 Perfluoroelastomer
Details
Perfluoroelastomer seal for SampleGenie4 two-part vial seal. Requires insert: 70-1757. Set of six.
Part number
Vial seal 70-1196 White viton
Details One-part, low leachable white viton, vial seal for use with SampleGenie4 Set of six.
Note: Notch in periphery indicates perflouro.
Part number
Vial seal 70-1197 Perfluoro
Details
One-part, highly resistant perfluoroelastomer, vial seal for use with SampleGenie4 Set of six.
Rocket Sample Holders
04-8931 Issue 1-14 October 2015 11
Part number
Vial adapter pad 70-1745 Diameter 16 mm
Details Vial adapter pad for SampleGenie4. Set of six.
Part number
Vial adapter pad 70-1746 Diameter 18 mm
Details Vial adapter pad for SampleGenie4. Set of six.
Part number
Vial adapter pad 70-1747 Diameter 24 mm
Details Vial adapter pad for SampleGenie4. Set of six.
Part number
Vial adapter pad 70-1748 Diameter 28 mm
Details Vial adapter pad for SampleGenie4. Set of six.
Rocket Sample Holders
12 04-8931 Issue 1-14 October 2015
GC Vial System2
Part number
GC Vial System2 70-1423 Viton seals
Details GC Vial System2 flask assembly with low leachable white viton vial seals. Set of six.
Part number
GC Vial System2 70-1424 Perfluoro seals
Details
GC Vial System2 flask assembly with highly resistant perfluoroelastomer vial seals. Set of six.
Rocket Sample Holders
04-8931 Issue 1-14 October 2015 13
GC Vial System2 spares
Part number
GC2 Flask 70-1425
Details Flask only, for GC Vial System2. Set of six.
Part number
Vial seal 70-1177 White viton
Details Low leachable white viton vial seal for GC Vial system2. Set of six.
Note: Notch in periphery indicates perfluoro.
Part number
Vial seal 70-1178 Perfluoro
Details Highly resistant perfluoroelastomer vial seal for GC Vial System2. Set of six.
Rocket Sample Holders
14 04-8931 Issue 1-14 October 2015
Part number
Vial adapter 70-1800
Details
Two-piece vial adapter with O-ring, for CG Vial System2 (backward compatible with all CG Vial System2 flask aseemblies, replaces one-piece vial adapter: 70-1428) Set of six.
Part number
O-ring 70-1801
Details O-ring for CG Vial System2 vial adapter: 70-1800. Set of six.
Part number
Collar pad 70-1317
Details Collar pad for GC Vial System2. Set of six.
Part number
GC2 collar 70-1320
Details Collar for GC Vial System2. Set of six.
Part number
Cap 70-1176
Details Cap for GC Vial System2. Set of six.
Rocket Sample Holders
04-8931 Issue 1-14 October 2015 15
Standard Flask
Part number
Standard flask assy 70-1321
Details Standard Flask with collar pad and collar. Set of six.
Standard flask spares
Part number
Standard flask 70-1170
Details Standard evaporation flask only. Set of six.
Part number
Collar pad 70-1317
Details
Collar pad for standard flask. For evaporators with serial numbers below RK0133, flask adapters must be removed from the rotor. Set of six.
Part number
Collar 70-1319
Details
Collar for standard flask. For evaporators with serial numbers below RK0133, flask adapters must be removed from the rotor. Set of six.
Rocket Sample Holders
16 04-8931 Issue 1-14 October 2015
ASE Tube Puck
Part number
Puck 70-1282
Details ASE* tube puck assembly. Set of six.
ASE Tube Puck spares
Part number
Puck seal 70-1287
Details Seal (viton O-ring) for ASE tube puck. Set of 18.
Rocket Sample Holders
04-8931 Issue 1-14 October 2015 17
Flip-Flop
Part number
Flip-Flop 70-1295 Viton seals
Details
Flip-Flop assembly with low leachable white viton seals. For use with ASE tube puck. Set of 18.
Part number
Flip-Flop 70-1296 Perfluoro seals
Details
Flip-Flop assembly with highly resistant perfluoroelastomer seals. For use with ASE tube puck. Set of 18.
*ASE is a registered trademark of Dionex Corporation.
Rocket Sample Holders
18 04-8931 Issue 1-14 October 2015
Flip-Flop Spares
Part number
Flip-Flop tube 70-1297
Details Double ended tube for Flip-Flop. Pack of 100 (plus 10 spare).
Part number
Tube seal 70-1304 White viton
Details Low leachable white viton tube seal for Flip-Flop (tube to funnel). Pack of 20.
Part number
Tube seal 70-1306 Perfluoro
Details Highly resistant perfluoroelastomer tube seal for Flip-Flop (tube to funnel). Pack of 20.
Part number
Funnel 70-1298
Details Funnel for Flip-Flop. Pack of 18.
Part number
O-ring 70-1299
Details O-ring for Flip-Flop (funnel to vial cover). Pack of 20.
Rocket Sample Holders
04-8931 Issue 1-14 October 2015 19
Part number
Vial seal 70-1303 White viton
Details Low leachable white viton vial seal for Flip-Flop. Pack of 20.
Note: Notch in periphery indicates perfluoro.
Part number
Vial seal 70-1305 Perfluoro
Details Highly resistant perfluoroelastomer vial seal for Flip-Flop. Pack of 20.
Part number
Ejector peg 70-1301
Details Vial ejector peg for Flip-Flop. Set of 18.
Part number
O-ring 70-1302
Details O-ring for Flip-Flop vial ejector peg. Pack of 20.
Part number
Vial cover 70-1300
Details Vial cover for Flip-Flop. Set of 18.
Rocket Sample Holders
20 04-8931 Issue 1-14 October 2015
Accessories
Sampleholder accessories
Part number
Flask carrier 70-1187
Details
Coated steel flask carrier for safe transportation or storage of six standard flasks, CG vial system flasks or SampleGenie flasks.
Part number
Flask stand 70-1797
Details Single flask stand for use as a balance nest with: standard flask, GC Vial system flask or SampleGenie flask.
Part number
Splash cap 70-1265
Details
Viton splash cap for use with: standard flask, GC vial system flask or SampleGenie flask. Set of six.
Part number
Seal tool 04-8321
Details
Tool for safe removal of vial seal from SampleGenie flask or GC vial system flask, without risk of damage to flask or seals.
Rocket Sample Holders
04-8931 Issue 1-14 October 2015 21
Infinity Trolley
Part number
Trolley 70-1650
Details
Infinity Trolley for Rocket and Rocket Synergy. Accommodates one Rocket high speed evaporator, Julao FL601 re-circulating chiller and five litre waste solvent container.
Part number
Trolley 70-1630
Details
Infinity Trolley for Rocket 4D and Rocket 4D Synergy. Accommodates one Rocket 4D and Julabo FL1701 recirculating chiller.
Part number
Shelf 70-1635
Details
Shelf kit for Infinity Trolley. Accommodates one Edwards nXDS6i vacuum pump or may be used as sample preparation area.
Rocket Sample Holders
22 04-8931 Issue 1-14 October 2015
General Spares
Main lid seal
Part number
Main lid seal 04-5818/S
Details Seal for main (outer) lid for Rocket Synergy, Rocket 4D Synergy and pre-Synergy Rockets.
Sample viewing window
Part number
Window 70-1182
Details Sample viewing window and gasket assembly for systems with strobe.
Waste solvent container
Part number
Waste container 70-1247/S 5 litre
Details
Waste solvent container kit comprising polypropylene waste solvent container, two port cap, drain hose (five metres) and fittings.
Lid joint coupling (for feed system)
Part number
O-ring 04-7943
Details O-ring (green perfluoroelastomer) for lid joint coupling (of feed system).
Rocket Sample Holders
04-8931 Issue 1-14 October 2015 23
Feed hoses
Part number
Feed hose 70-1553/S
Details Replacement feed hose. 50 metre length.
Fittings for coolant, drain and exhaust hoses
Part number
Hose fittings 70-1651/S
Details
Hose fittings kit comprising two type 1A fittings and two type 2N fittings for coolant, drain and exhaust hose connections.
Rocket Sample Holders
24 04-8931 Issue 1-14 October 2015
Quick Reference
Part numbers
04-1247/S ..................... 22 04-5676 .......................... 6 04-5818/S ..................... 22 04-7448/S ....................... 6 04-7652/S ....................... 5 04-7943 ........................ 22 04-8321 ........................ 20 04-8844 .......................... 7 04-8850/S ....................... 7 70-1170 ........................ 15 70-1176 ........................ 14 70-1177 ........................ 13 70-1178 ........................ 13 70-1180 .......................... 6 70-1182 ........................ 22 70-1186 .......................... 7 70-1187 ........................ 20 70-1196 ........................ 10 70-1197 ........................ 10 70-1265 ........................ 20 70-1282 ........................ 16 70-1287 ........................ 16 70-1295 ........................ 17 70-1296 ........................ 17 70-1297 ........................ 18 70-1298 ........................ 18 70-1299 ........................ 18
70-1300 ........................ 19 70-1301 ........................ 19 70-1302 ........................ 19 70-1303 ........................ 19 70-1304 ........................ 18 70-1305 ........................ 19 70-1306 ........................ 18 70-1317 .................. 14, 15 70-1319 ........................ 15 70-1320 ........................ 14 70-1321 ........................ 15 70-1423 ........................ 12 70-1424 ........................ 12 70-1425 ........................ 13 70-1547/S ...................... 5 70-1548/S ...................... 5 70-1549/S ...................... 5 70-1552/S ...................... 7 70-1553/S .................... 23 70-1556/S ...................... 6 70-1557/S ...................... 6 70-1630 ........................ 21 70-1635 ........................ 21 70-1650 ........................ 21 70-1651/S .................... 23 70-1734/S ...................... 4 70-1740 .......................... 8
70-1741 .......................... 9 70-1742 .......................... 9 70-1743 .......................... 9 70-1744 .......................... 9 70-1745 ........................ 11 70-1746 ........................ 11 70-1747 ........................ 11 70-1748 ........................ 11 70-1752/S ....................... 4 70-1757 ........................ 10 70-1758 ........................ 10 70-1759 ........................ 10 70-1760 .......................... 8 70-1761 .......................... 8 70-1762 .......................... 8 70-1763 .......................... 8 70-1764 .......................... 8 70-1765 .......................... 8 70-1766 .......................... 8 70-1767 .......................... 8 70-1768 .......................... 8 70-1769 .......................... 8 70-1797 ........................ 20 70-1798 .......................... 7 70-1800 ........................ 14 70-1801 ........................ 14 70-1820/S ....................... 4
Rocket Sample Holders
04-8931 Issue 1-14 October 2015 25
Amendment control
Issue Reason for Change Date Issued
1-1 First release 19-Dec-14
1-2 70-1759 images updated. Serial number limit for pre-Synergy systems added.
08-Jan-15
1-3 SG4 vial seal part number correction and duplications removed. Flip-Flop vial seal part number changed for pack of 20. Perflouro identification notes added.
09-Jan-15
1-4 70-1196, 70-1197, 70-1177, 70-1178 reintroduced. “Also used in” comments removed. Rotor hub O-ring removed.
29-Jan-15
1-5 Waste connection kit part number corrected. 17-Feb-15
1-6 04-5676, 04-7943, 70-1557/S included. 26-Mar-15
1-7 Pouring stand for bowl rotor – part number updated to reflect design change. Flask stand (balance nest) part number updated.
30-Apr-15
1-8 SG4 vials adapter DJ introduced. 14-May-15
1-9 70-1820/S introduced. Batch baffles added to 70-1820/S, feed baffles added to 70-1752/S.
22-May-15
1-10 GC Vial System2 vial addapter: 70-1800 replaces 70-1428, 70-1801 replaces 70-1429.
30-Jul-15
1-11 Address: SpScientific replaces SP industries. 10-Aug-15
1-12 Cap separated from GC Collar2; added as separate item. 27-Aug-15
1-13 V3 Blanking Plug added. 30-Sept-15
1-14 Minor correction. 07-Oct-15
Genevac Ltd The Sovereign Centre Farthing Road Ipswich IP1 5AP United Kingdom
Service: +44 (0) 1473 243000
Sales: +44 (0) 1473 240000 Fax: +44 (0) 1473 461176
Email: [email protected] [email protected] [email protected]
Web site: http://www.genevac.com
Genevac Inc SP Scientific 3538 Main Street Stone Ridge NY12484 United States of America
Sales & Service: (1) 845 267 2211 Fax: Fax (1) 845 267 2212
Email: [email protected]
Genevac Ltd operates a continuous development programme aimed at further improving products, all specifications are therefore subject to change. Coolheat® VacRamp™, Dri-Pure®, SampleGuard™, SampleGenie™ and associated logos are trade-marks of Genevac Ltd, unauthorised use is prohibited. Your Genevac Sales Representative will be happy to advise on the availability of special order items in addition to the sample holders listed in this Accessories Brochure All rights reserved, © Genevac Ltd 2015.