GE Oil & Gas NTC - GE Oil and Gas · GE imagination at work GE Oil & Gas GE imagination at work...
2
GE imagination at work GE Oil & Gas GE imagination at work Specifcations Flow Rate 15 – 300 US gpm (514-10,285 BPD or 82-1635 m 3 /D) Maximum Discharge Pressure 2500 psi (172 bar) (Application dependent rating) Max Shaft Horsepower (60Hz) Up to 75 HP (56 kW) Max Fluid Temperature 200°F (93°C) Housing Metallurgy Standard carbon steel Corrosion resistant options Stage Metallurgy Ni-resist Type 1 Maximum Suction PSI 260 psi (18 bar) @ 200°F (93°C) Typical System Lengths 6ft (1.8 m) - 21ft (6.4m) NTC Close-Coupled Surface Pumping System Compact design combined with lower upfront costs and minimal maintenance help maximize run time and minimize operating costs. The GE Oil & Gas Surface Pumping Systems No Thrust Chamber (NTC) model is the latest ofering designed to meet the needs o f an ever evolving, high demand market. Featuring a design that does not require a thrust chamber, the NTC has lower upfront cost and reduced system complexity to improve reliability. With fow rates ranging from 15 gpm to 300 gpm, the NTC can be confgured for a wide range of applications, with higher output pressure than many alternative pump technologies. The NTC can also be confgured with Abrasion Resistant bearings to further protect the system and increase run life.
-
Upload
dinhkhuong -
Category
Documents
-
view
226 -
download
0
Transcript of GE Oil & Gas NTC - GE Oil and Gas · GE imagination at work GE Oil & Gas GE imagination at work...
GE imagination at work
GE Oil & Gas
GE imagination at work
Specifications
Flow Rate 15 – 300 US gpm (514-10,285 BPD or 82-1635 m3/D)
Maximum Discharge Pressure
2500 psi (172 bar) (Application dependent rating)
Max Shaft Horsepower (60Hz) Up to 75 HP (56 kW)
Max Fluid Temperature 200°F (93°C)
Housing Metallurgy Standard carbon steel Corrosion resistant options
Stage Metallurgy Ni-resist Type 1 Maximum Suction PSI 260 psi (18 bar) @ 200°F (93°C) Typical System Lengths 6ft (1.8 m) - 21ft (6.4m)
NTC Close-Coupled Surface Pumping System Compact design combined with lower upfrontcosts and minimal maintenance help maximizerun time and minimize operating costs.
The GE Oil & Gas Surface Pumping Systems No Thrust Chamber (NTC) model is the latest offering designed to meet the needs of an ever evolving, high demand market. Featuring a design that does not require a thrust chamber, the NTC has lower upfront cost and reduced system complexity to improve reliability. With flow rates ranging from 15 gpm to 300 gpm, the NTC can be configured for a wide range of applications, with higher output pressure than many alternative pump technologies. The NTC can also be configured with Abrasion Resistant bearings to further protect the system and increase run life.
GE imagination at work
GE Oil & Gas
Applications 4425 Westway Blvd • Crude oil boosting/ transfer • Process fluids transfer Houston, TX 77041 USA • Jet pumping • Produced water disposal 713 260 6740 • Lean amine circulation • Produced water injection geoilandgas.com/sps • Mine dewatering • LACT
• Pipeline boosting
Features Benefits • Low pump thrust eliminates need for thrust • Reduced maintenance, upfront costs, and less
chamber mechanical parts for repairs • Designed to be compact • Small footprint reduces site space requirement and • Designed with rear pull-out seal optimizes facility design • Standard C-Face, foot mounted NEMA frame • Minimal downtime for mechanical seal
motors maintenance or replacements • Non pulsating flow • Motor easily replaced
Performance for SD & SE Series Pumps
Pres
sure
(psi
)
2750
2500
2250
2000
1750
1500
1250
1000
750
500
250
SD0013 SD0019 SD0025
SD0038
SE0052 SE0080
SD0052
SE0115
SE0125
SE0230
SE0170
5 10 20 30 40 50 60 70 80 90 100 200
Flow (US gpm) Note: These values are for pumps running at 3570rpm at 1 SG.
