GasLiquid Separators-Design Rules
-
Upload
wahyuriansyah -
Category
Documents
-
view
74 -
download
9
description
Transcript of GasLiquid Separators-Design Rules
-
GAS/LIQUID SEPARATORSDESIGN RULESFanda KurniawanFeb 25th, 2009
-
OUTLINES01. Components02. Selection Criteria for Gas/Liquid Separators- Vertical KO Drum- Horizontal KO Drum- Vertical Wire Mesh Demister- Horizontal Wire Mesh Demister03. Design Rules
-
01. COMPONENTSA. Feed inletB. Separator internals- Wire Mesh- Vane PackC. Gas and liquid outlets
-
02. Selection Criteria for Gas/Liquid SeparatorsVERTICAL
- A smaller plan area is required (critical on offshore platforms)- Easier solids removal- Liquid removal efficiency does not vary with liquid level (area in vessel available for gas flow remains constant)- Vessel volume is generally smaller
HORIZONTAL
- Large liquid slugs have to be accommodated;- There is restricted head room;- A low downward liquid velocity is required (for de-gassing purposes or for foam breakdown).
-
VERTICAL KO DRUM
-
VERTICAL KO DRUM (Contd)Application: bulk separation of gas and liquid.Characteristics:- unlimited turndown;- high slug handling capacity;- liquid removal efficiency typically 90%;Warning: poor removal efficiency of liquid from mist- very low pressure drop;- insensitive to fouling.Recommended use:- vessels where internals have to be kept to a minimum - foaming service.Non-recommended use:- where efficient demisting of gas is required.Typical process applications:- vent and flare stack knockout drums;- production separator;- bulk separator (e.g. upstream of gas coolers)
-
VERTICAL KO DRUM (Contd) Diameter
Height
NozzleIf no inlet device is fitted, the momentum criterion 1 000 to 2000 Pa.If a half-open pipe is fitted, the momentum criterion 1 500 to 5000 Pa.If a Schoepentoeter is fitted, the momentum criterion from 6 000 to 10 000 Pa.Pressure Drop
-
HORIZONTAL KO DRUM
-
HORIZONTAL KO DRUM (Contd)Application:- bulk separation of gas and liquid.Characteristics:- can handle large liquid fractions;- unlimited turndown;- very high slug handling capacity;- liquid removal efficiency typically 90%Warning: poor removal efficiency of liquid from mist;- very low pressure drop;- insensitive to fouling.Recommended use:- vessels where internals have to be kept to a minimum and where there are height limitations;- slug catchers;- fouling service, e.g. wax, sand, asphaltenes; - for foaming or very viscous liquids.Non-recommended use:- where efficient demisting of gas is required.Typical process applications:- vent and flare stack knock-out drums;- production separator for low gas/oil ratio (GOR);- bulk separator;- slug catcher.
-
HORIZONTAL KO DRUM (Contd)Diameter
Pressure Drop
-
VERTICAL WIREMESH DEMISTER
-
VERTICAL WIREMESH DEMISTER (Contd)Application : demisting of gas.Characteristics:- high turndown ratio (factor 4);- high slug handling capacity;- liquid removal efficiency > 98%;- low pressure drop.Recommended use:- for demisting service with a moderate liquid load in form of droplets;- where slug handling capacity may be required.Non-recommended use:- fouling service (wax, asphaltenes, sand, hydrates)- for viscous liquids where de- gassing requirement determines vessel diameter
-
VERTICAL WIREMESH DEMISTER (Contd)Turn DownThe efficiency of the demister mat will decrease at gas flows less than around 30% of the design limit if the droplet sizeEfficiencyGreater than 98% can be assumed for a correctly sized vertical demisting vessel
-
VERTICAL WIREMESH DEMISTER (Contd)Diameter
Height
Pressure Drop
-
HORIZONTAL WIREMESH DEMISTER
-
HORIZONTAL WIREMESH DEMISTER (Contd)Application : demisting of gas where a high liquid handling capacity is required.Characteristics:- high turndown ratio - very high slug handling capacity;- liquid removal efficiency > 98%;- sensitive to fouling;- low pressure drop.Typical process applications:- production/test separator for low GOR- applications with height limitations.
Recommended use:- typically for demisting service with a high liquid load and a low GOR;- applied where slug handling capacity may be required;- for viscous liquids where liquid de-gassing requirement determines vessel diameter;- for foaming liquids.Non-recommended use:- Fouling service (wax, asphaltenes, sand).
-
03. Design RulesNature of FeedFlow regime in the feed pipeThe feed entering a G/L separator can be in the form of mist, stratified flow, slug flow, etc. depending on the flow rates and physical properties of the gas and liquid phases and on the feed pipe characteristics (diameter, length, vertical/ horizontal).
-
Design Rules (Contd)Sizing of Feed and Outlet NozzleFeed Inlet
-
Sizing of Feed and Outlet Nozzle (Contd)Gas Outlet
Liquid Outlet- Velocity does not exceed 1 m/s
-
THANK YOU