Garage Door Banners - Cloudinary · 2019. 5. 15. · Garage Door Banner Graphic Garage Door Banners...

9/17 Product Parts 1 - Top Clamp (x4 single door),(x6 double door*) 2 - Top Clamp Connector (x4 single door),(x6 double door*) 3 - Bottom Tension Clamp (x4 single door),(x6 double door*) 4 - Screws/Nuts (x8 single door),(x12 double door*) 5. Garage Door Banner Graphic Garage Door Banners Display Set-Up Place Top Clamps (1), evenly spaced, along top of garage door. Step 2 Raise garage 6” to 12” to allow for easier access to clamps. Step 4 Feed hook on Bottom Tension Clamp (3) through hole on Graphic (5) Optional: Cut slit in graphic to allow for garage door handle. Step 3 Attach the Bottom Tension Clamps (3), evenly spaced, along bottom of the garage door. 1 4 2 Storage & Care Store in a cool dry location. Vinyl: Spot clean with damp cloth. Optional 3 5 *Amount is doubled for a Split Double Garage Door and varies for custom sizes. Side View Graphic Hook on Bottom Tension Clamp Hole in Graphic This part of Bottom Tension Clamp moves up and down under spring tension. Step 5 Reconnect power and remove blocking. Resume normal operation of garage door. Step 1 Unroll Graphic (5) and locate pre-drilled holes along top of the Graphic (5). Place the Graphic (5) over Top Clamp (1) and feed two Screws (4) through Top Clamp Connector (2) and hole on Graphic (5) then into nut on the back of the Top Clamp (1). Repeat for remaining Top Clamps. WARNING: Disconnect power and block door to prevent accidental closing. Placing of Graphic and hardware requires a minimum of 2 people. Side View Graphic Top Clamp Connector Front View Graphic Top Clamp Connector D o o r Top Clamp Garage Door (Street View) Side View Front DoorGarage Door (Street View) Side View BLOCK BLOCK

Upload
others
Category

Documents
view
2
download
0

Embed Size (px):

Transcript of Garage Door Banners - Cloudinary · 2019. 5. 15. · Garage Door Banner Graphic Garage Door Banners...

Page 1: Garage Door Banners - Cloudinary · 2019. 5. 15. · Garage Door Banner Graphic Garage Door Banners Display Set-Up Place Top Clamps (1), evenly spaced, along top of garage door. Step

9/17

Product Parts

1 - Top Clamp (x4 single door),(x6 double door*) 2 - Top Clamp Connector (x4 single door),(x6 double door*) 3 - Bottom Tension Clamp (x4 single door),(x6 double door*) 4 - Screws/Nuts (x8 single door),(x12 double door*) 5. Garage Door Banner Graphic

Garage Door Banners

Display Set-Up

Place Top Clamps (1), evenly spaced, along top of garage door.

Step 2 Raise garage 6” to 12” to allow for easier access to clamps.

Step 4 Feed hook on Bottom Tension Clamp (3) through hole on Graphic (5)

Optional: Cut slit in graphic to allow for garage door handle.

Step 3 Attach the Bottom Tension Clamps (3), evenly spaced, along bottom of the

garage door.

Storage & CareStore in a cool dry location. Vinyl: Spot clean with damp cloth.

Optional

*Amount is doubled for a Split Double Garage Door and varies for custom sizes.

Side View

Graphic

Hook onBottom TensionClamp

Hole inGraphic

This part of Bottom Tension Clamp moves up and down under spring tension.

Step 5 Reconnect power and remove blocking. Resume normal operation of garage door.

Step 1 Unroll Graphic (5) and locate pre-drilled holes along top of the Graphic (5). Place the Graphic (5) over Top Clamp (1) and feed two Screws (4) through Top Clamp Connector (2) and hole on Graphic (5) then into nut on the back of the

Top Clamp (1). Repeat for remaining Top Clamps.

WARNING: Disconnect power and block door to prevent accidental closing. Placing of Graphic and hardware requires a minimum of 2 people.

Side View

Graphic

Top Clamp Connector

Front View

Graphic

Top ClampConnector

Door

Top Clamp

Product Parts (Single)

1 - Top Clamp (x3)2 - Top Clamp Connector (x3)3 - Bottom Clamp (x3)4 - Ball Bungee (x3)5 - Screws (x6)6 - Washers (x6)7 - Graphic