G780 4kv Phase Module Replacement RevA1.ppt · Exchanging phase modules Pl h Maintenance 11. Place...
Transcript of G780 4kv Phase Module Replacement RevA1.ppt · Exchanging phase modules Pl h Maintenance 11. Place...
4 KV Phase Module Replacement
Michael Basler, ATD1/Training JCF/BMI,
13.05.2009
ACS 2000Service & Commissioning
C G78013.05.2009Course G780
aini
ng -R
evA
1-
ACS
2000
Tra
© A
BB
Ltd
-1
Phase modulesMaintenance
Power electronic building block
Integrated logic for control of IGBTs
Identical for operation in inverter and active rectifier
Hi h il bilit d t f tHigh availability due to fast module exchange
Converter downtime
aini
ng -R
evA
12
-
Converter downtime (MTTR) in the range of 20 min
ACS
2000
Tra
© A
BB
Ltd
-2
Phase modulesMaintenance
Phase module A
Phase module B
Inverter Unit (INU)
Phase module C
( )
Phase module A
Phase module
aini
ng -R
evA
13
-
Phase module B
Phase module C
Active Front End (AFE)
ACS
2000
Tra
© A
BB
Ltd
-3
Exchanging phase modulesMaintenance
1. Turn off main incoming supply and ground the converterUse Lock-Out-Tag Out procedure and open converter door
2. Turn off auxiliary power supply of the phase modules
3. Remove the Plexiglas cover
4. Remove the screws on the left/right side of the phase moduleg p
aini
ng -R
evA
14
-AC
S 20
00 T
ra©
AB
B L
td -
4
Phase modules5 Insert the module tray into the
Maintenance
5. Insert the module tray into thecabinet along the lower sides of the phase module.
6 Slide the phase module tray tool in6. Slide the phase module tray tool in until it makes contact with the metal flange on both sides of the NP frame.
7. Open the securing hinges of the tray7. Open the securing hinges of the tray tool to secure the tray tool to the drive frame (This is to prevent movement of the tray tool while removing module.
aini
ng -R
evA
15
-AC
S 20
00 T
ra©
AB
B L
td -
5
Phase modulesMaintenance
f f f f8. Unplug fiber optic cables and control wiring connector from the front of the phase module. Carefully position so as to not damage the cables when changing phase module.
aini
ng -R
evA
16
-AC
S 20
00 T
ra©
AB
B L
td -
6
Phase modulesMaintenance
9. Hold the phase module by the handle and pull slowly, verifying that the Module Tray tool isTray tool is firmly in place.
aini
ng -R
evA
17
-AC
S 20
00 T
ra©
AB
B L
td -
7
Exchanging phase modulesMaintenance
10. Lift the phase module off of the tray. The phase module weighs approximately 35 kg [77 lbs.] . It is recommended that two people, one on each side lift the phase module.
aini
ng -R
evA
18
-AC
S 20
00 T
ra©
AB
B L
td -
8
Exchanging phase modulesPl h
Maintenance
11. Place new phase module on tray and gently push into place, being careful not to gdamage fiber optic and power cables. Tighten the fastening bolts that secure module tosecure module to cabinet on each side.
NOTE: Once in place, remove the phase capacitor shorting strip. Install strip on phase
aini
ng -R
evA
19
-
Install strip on phase module that was removed.
ACS
2000
Tra
© A
BB
Ltd
-9
Exchanging phase modulesMaintenance
12. Remove Phase module tray tool.
aini
ng -R
evA
10
-
13. Reconnect fiber optic and power cables.
ACS
2000
Tra
© A
BB
Ltd
-1
Exchanging phase modulesMaintenance
14. Reinstall the plexiglass air plenum.
15 Switch on all miniature circuit breakers in the control15. Switch on all miniature circuit breakers in the control compartment.
16. Close door, remove Lock-Out-Tag-Outg
17. Unground the drive and use standard drive start up procedures.
aini
ng -R
evA
11
-AC
S 20
00 T
ra©
AB
B L
td -
1