Fujikura News “Tsunagu” Technology New Product News ... · Fujikura News 7 “Tsunagu”...
4
Since the Feed-in Tariff has been started in July 2012, there have been an increase in inquiries about cables and equipment and materials for interconnecting power systems of mega solar generators and wind generators. Fujikura has developed an anti-pollution silicon plug-in terminal module to replace indoor prefabricated (plug-in) terminals and terminals with anti-pollution-type insulators that have been used to connect to a transformer or ring main unit. This new product can operate at a rated voltage up to 33 kV in areas like inside a building to a heavily polluted area. ●Considerable improvement in ease of assembly thanks to much lighter weight than insulation-type product and plug-in system requiring no skills ●Unlike product shrinking at room temperature, no need to worry about faulty installation work (rework) ●Usable in heavily polluted area (estimated salt adhesion amount up to 0.35 mg /cm 2 ) due to use of silicone rubber Features Power Systems EPC Division [email protected] E Anti-pollution silicon plug-in terminal module Product Specifications Items Rated voltage Places of use Suitable CV cable size Power-frequency withstand voltage Power-frequency partial discharge Lighting impulse withstand voltage Flashover voltage of polluted insulator Number of shades Specifications 22 kV Inside of building - heavily polluted area 60 mm 2 - 325 mm 2 57 kV AC × 3 hours 17 kV/10 pC or lower -230 kV × 3 times 23 kV or higher 3 33 kV Inside building - heavily polluted area 60 mm 2 - 325 mm 2 86 kV AC × 3 hours 26 kV/10 pC or lower -305 kV × 3 times 34.5 kV or higher 4 Compliant with JCAAA502 (terminal for 22 kV/33 kV cross-linked polyethylene insulated power cable for outdoor use) Tele- communi- cations Development of Anti-pollution Silicone Plug-in Terminal Module 4 2 0 1 6 N o . 4 1 7 Fujikura News “Tsunagu” Technology New Product News 2016 4
Transcript of Fujikura News “Tsunagu” Technology New Product News ... · Fujikura News 7 “Tsunagu”...
Since the Feed-in Tariff has been started in July 2012, there have been an increase in inquiries about cables and equipment and materials for interconnecting power systems of mega solar generators and wind generators. Fujikura has developed an anti-pollution silicon plug-in terminal module to replace indoor prefabricated (plug-in) terminals and terminals with anti-pollution-type insulators that have been used to connect to a transformer or ring main unit. This new product can operate at a rated voltage up to 33 kV in areas like inside a building to a heavily polluted area.
Launch of Business Integration with Fujikura Dia Cable Ltd.
Fujikura Ltd. and Mitsubishi Cable Industries, Ltd. have been operating a wire and cable sales business for construction and electric work by establishing a joint venture company, Fujikura Dia Cable Ltd. (Fujikura's capital ratio: 70%, Mitsubishi's: 30%, hereinafter FDC) since January 2005. Fujikura and Mitsubishi started consolidating their manufacturing and sales operation regarding industrial wire and cable into FDC on April 1, 2016 to strengthen their business by synergy effects through using both companies' strengths.
●Considerable improvement in ease of assembly thanks to much lighter weight than insulation-type product and plug-in system requiring no skills
●Unlike product shrinking at room temperature, no need to worry about faulty installation work (rework)
●Usable in heavily polluted area (estimated salt adhesion amount up to 0.35 mg /cm2) due to use of silicone rubber
Features
Power Systems EPC Division [email protected]
Anti-pollution silicon plug-in terminal module
Product SpecificationsItems
Rated voltagePlaces of use
Suitable CV cable sizePower-frequency withstand voltagePower-frequency partial discharge
Lighting impulse withstand voltageFlashover voltage of polluted insulator
Number of shades
Specifications
22 kV
Inside of building - heavily polluted area
60 mm2 - 325 mm2
57 kV AC × 3 hours
17 kV/10 pC or lower
-230 kV × 3 times
23 kV or higher
3
33 kV
Inside building - heavily polluted area
60 mm2 - 325 mm2
86 kV AC × 3 hours
26 kV/10 pC or lower
-305 kV × 3 times
34.5 kV or higher
4
Compliant with JCAAA502 (terminal for 22 kV/33 kV cross-linked polyethylene insulated power cable for outdoor use)
Establishment of Fujikura Cube
In November 2015, Fujikura established Fujikura Cube Ltd. to employ persons with disabilities. The company completed employing persons with disabilities, securing staff and constructing facilities and launched its operation with 10 employees on April 1, 2016.Fujikura Cube mainly takes charge of greening on the premises, cleaning the dormitory and company houses and shipping documents. The company will expand its business to some services in the Fujikura Group after gaining approval as a special subsidiary in June.
Name of company：Fujikura Dia Cable Ltd.Location：Konwa Bldg. Tsukiji 1-12-22 Chuo Ward, TokyoRepresentative：President Tadatoshi Kuge
Outline of FDC after consolidation
Capital：5.4 billion yenDate of establishment：January 26, 2005Number of employees：Approximately 700
Name of company：Fujikura Cube Ltd.Location：Mutsuzaki 1440 Sakura City, Chiba PrefectureRepresentative：President Hiroyuki Mizuno
Outline of Fujikura Cube Ltd.
Capital：10 million yen (100% financed by Fujikura)Date of establishment：November 2, 2015Number of employees：10
Tele-communi-cations
Development of Anti-pollution Silicone Plug-in Terminal Module
Other
Other
Fujikura News
44
2016 No.417
Development of Anti-pollution Development of Anti-pollution Development of Anti-pollution Development of Anti-pollution
Fujikura News“Tsunagu” Technology New Product News
Fujikura Ltd.1-5-1, Kiba, Koto-ku, Tokyo, Japan 135-8512TEL. +81（0）3 5606 1112 FAX. +81（0）3 5606 1501Issue : April 2016, No. 417 Editor in Chief : Keisuke Okamurahttp://www.fujikura.co.jp
Sales Support & Branch Off ice Management DepartmentKansai Off iceChubu Off iceTohoku Off iceKyushu Off ice
+81(0)3 5606 1095+81(0)6 6364 0373+81(0)52 212 1880+81(0)22 266 3344+81(0)92 291 6126
2016
4
Fujikura News
8th Data Center Expo Spring
Fujikura will be exhibiting at 8th Data Center Expo Spring to be held in May.Focus of the exhibition is on the products and services pertaining to the construction and operation of data centers. We will be presenting solutions consisting of the Fujikura Group's products for data centers under the slogan, "We will become the most trusted partner in the field of Tsunagu (connecting) technologies." As an example of our optical wiring solutions, we will show an economical, efficient MPO optical cabling system that realize the advanced optical network infrastructure sustainable and expandable for 10 years ahead. Furthermore, the Fujikura Group's most advanced technologies for a next generation broadband network will also be on display. In addition, as an IT solution that Fujikura works on, there will be a display of our environmentally-friendly power cable portofolio that is suitable for renewable energy systems.On top of these exhibits, we will present our versatile products to support day-to-day data center operation such as splicers, measurement and test equipment, optical connectors, cleaners and active optical cables (AOCs) along with the photos of them and also demonstrated.We look forward to seeing you at our booth.
Highly expandable with ease of relocation, addition and replacement upon requestEfficient and economical transition to 10 G / 40 G / 100 G in future
MPO optical cabling systemExternal view of product
Package as small as grain of rice
Fujikura has developed an ultra-small water-proof digital output absolute pressure sensor (the ABS5 series). As this sensor has a waterproof structure, it will find applications in measuring altitude and depth using waterproof electronic equipment for outdoor use. This new product is even smaller than a current analog output absolute pressure sensor (the FPBS series). In terms of functions, the new product digitally outputs accurate pressure and temperature data since it performs a correction calculation of the output signals using its built-in temperature sensor and signal processing circuit.Thanks to these additional functions, this absolute pressure sensor requires no complicated adjustment or corrective calculation on the customer's part and enables easy incorporation into a device.The sales of the product starts in December 2016.
Ultra-small Water-proof Digital Absolute Pressure Sensor
１. High waterproofnessPackage design capable of standing high pressure of 1 MPa (equivalent to water pressure at 90 m depth)
２. MiniaturizedSmall-sized package of φ 4.0 mm × 1.85 mm
３. Digital output16-bit digital output of pressure data and temperature data compensated for accuracy
４. High resolutionPressure resolution of 0.02 hPa (equivalent to about 16 cm height resolution near ground surface)
Features
Product specificationsModel
Outer diameter of packagePressure / temperature output data format
Pressure measurement rangePressure resolutionPressure medium
Operating temperature rangeAccurate compensation temperature range
Operating voltageAverage consumed current
ABS5-100KA ABS5-450KA Unit
300 ～ 11000.02
φ4.0 ×1.8516 bit , I2CTM
Noncorrosive gasses, water, salt water-40 ～ 85-10 ～ 601.8 ～ 3.6
9
mm-
hPahPa/count
-℃℃V
μA/sample/sec
300 ～ 45000.084
I2CTMis a registered trademark of NXP Semiconductors.
Electronic Component Division [email protected] Cable System Division [email protected]
Only this part is modified as per standards.
Patch code
LC Duplex - LC Duplex
12MPO - 12MPO
24MPO - 12MPO x2
MPO-LC module4U chassis
12 MPOconnector
MPO trunk cable12 f ～ 144 f
Tension member
Subunit
Outer sheath
Rip cord
MPO adaptor panel
Module
No need for replacement
10GBASE-SR
40GBASE-SR4100GBASE-SR4
100GBASE-SR10
Ultra-small Water-proof Digital Absolute Pressure Sensor
Electro-nics
Exhibition
May 11 (Wed) - 13 (Fri）, 10:00 am to 6:00 pm (last day 5:00 pm) Tokyo Big Sight (Fujikura booth East 31-40)
Dates
Location
Fujikura News
8th Data Center Expo Spring
Fujikura will be exhibiting at 8th Data Center Expo Spring to be held in May.Focus of the exhibition is on the products and services pertaining to the construction and operation of data centers. We will be presenting solutions consisting of the Fujikura Group's products for data centers under the slogan, "We will become the most trusted partner in the field of Tsunagu (connecting) technologies." As an example of our optical wiring solutions, we will show an economical, efficient MPO optical cabling system that realize the advanced optical network infrastructure sustainable and expandable for 10 years ahead. Furthermore, the Fujikura Group's most advanced technologies for a next generation broadband network will also be on display. In addition, as an IT solution that Fujikura works on, there will be a display of our environmentally-friendly power cable portofolio that is suitable for renewable energy systems.On top of these exhibits, we will present our versatile products to support day-to-day data center operation such as splicers, measurement and test equipment, optical connectors, cleaners and active optical cables (AOCs) along with the photos of them and also demonstrated.We look forward to seeing you at our booth.
Highly expandable with ease of relocation, addition and replacement upon requestEfficient and economical transition to 10 G / 40 G / 100 G in future
MPO optical cabling systemExternal view of product
Package as small as grain of rice
Fujikura has developed an ultra-small water-proof digital output absolute pressure sensor (the ABS5 series). As this sensor has a waterproof structure, it will find applications in measuring altitude and depth using waterproof electronic equipment for outdoor use. This new product is even smaller than a current analog output absolute pressure sensor (the FPBS series). In terms of functions, the new product digitally outputs accurate pressure and temperature data since it performs a correction calculation of the output signals using its built-in temperature sensor and signal processing circuit.Thanks to these additional functions, this absolute pressure sensor requires no complicated adjustment or corrective calculation on the customer's part and enables easy incorporation into a device.The sales of the product starts in December 2016.
Ultra-small Water-proof Digital Absolute Pressure Sensor
１. High waterproofnessPackage design capable of standing high pressure of 1 MPa (equivalent to water pressure at 90 m depth)
２. MiniaturizedSmall-sized package of φ 4.0 mm × 1.85 mm
３. Digital output16-bit digital output of pressure data and temperature data compensated for accuracy
４. High resolutionPressure resolution of 0.02 hPa (equivalent to about 16 cm height resolution near ground surface)
Features
Product specificationsModel
Outer diameter of packagePressure / temperature output data format
Pressure measurement rangePressure resolutionPressure medium
Operating temperature rangeAccurate compensation temperature range
Operating voltageAverage consumed current
ABS5-100KA ABS5-450KA Unit
300 ～ 11000.02
φ4.0 ×1.8516 bit , I2CTM
Noncorrosive gasses, water, salt water-40 ～ 85-10 ～ 601.8 ～ 3.6
9
mm-
hPahPa/count
-℃℃V
μA/sample/sec
300 ～ 45000.084
I2CTMis a registered trademark of NXP Semiconductors.
Electronic Component Division [email protected] Cable System Division [email protected]
Only this part is modified as per standards.
Patch code
LC Duplex - LC Duplex
12MPO - 12MPO
24MPO - 12MPO x2
MPO-LC module4U chassis
12 MPOconnector
MPO trunk cable12 f ～ 144 f
Tension member
Subunit
Outer sheath
Rip cord
MPO adaptor panel
Module
No need for replacement
10GBASE-SR
40GBASE-SR4100GBASE-SR4
100GBASE-SR10
Electro-nics
Exhibition
May 11 (Wed) - 13 (Fri）, 10:00 am to 6:00 pm (last day 5:00 pm) Tokyo Big Sight (Fujikura booth East 31-40)
Dates
Location
Since the Feed-in Tariff has been started in July 2012, there have been an increase in inquiries about cables and equipment and materials for interconnecting power systems of mega solar generators and wind generators. Fujikura has developed an anti-pollution silicon plug-in terminal module to replace indoor prefabricated (plug-in) terminals and terminals with anti-pollution-type insulators that have been used to connect to a transformer or ring main unit. This new product can operate at a rated voltage up to 33 kV in areas like inside a building to a heavily polluted area.
Launch of Business Integration with Fujikura Dia Cable Ltd.
Fujikura Ltd. and Mitsubishi Cable Industries, Ltd. have been operating a wire and cable sales business for construction and electric work by establishing a joint venture company, Fujikura Dia Cable Ltd. (Fujikura's capital ratio: 70%, Mitsubishi's: 30%, hereinafter FDC) since January 2005. Fujikura and Mitsubishi started consolidating their manufacturing and sales operation regarding industrial wire and cable into FDC on April 1, 2016 to strengthen their business by synergy effects through using both companies' strengths.
●Considerable improvement in ease of assembly thanks to much lighter weight than insulation-type product and plug-in system requiring no skills
●Unlike product shrinking at room temperature, no need to worry about faulty installation work (rework)
●Usable in heavily polluted area (estimated salt adhesion amount up to 0.35 mg /cm2) due to use of silicone rubber
Features
Power Systems EPC Division [email protected]
Anti-pollution silicon plug-in terminal module
Product SpecificationsItems
Rated voltagePlaces of use
Suitable CV cable sizePower-frequency withstand voltagePower-frequency partial discharge
Lighting impulse withstand voltageFlashover voltage of polluted insulator
Number of shades
Specifications
22 kV
Inside of building - heavily polluted area
60 mm2 - 325 mm2
57 kV AC × 3 hours
17 kV/10 pC or lower
-230 kV × 3 times
23 kV or higher
3
33 kV
Inside building - heavily polluted area
60 mm2 - 325 mm2
86 kV AC × 3 hours
26 kV/10 pC or lower
-305 kV × 3 times
34.5 kV or higher
4
Compliant with JCAAA502 (terminal for 22 kV/33 kV cross-linked polyethylene insulated power cable for outdoor use)
Establishment of Fujikura Cube
In November 2015, Fujikura established Fujikura Cube Ltd. to employ persons with disabilities. The company completed employing persons with disabilities, securing staff and constructing facilities and launched its operation with 10 employees on April 1, 2016.Fujikura Cube mainly takes charge of greening on the premises, cleaning the dormitory and company houses and shipping documents. The company will expand its business to some services in the Fujikura Group after gaining approval as a special subsidiary in June.
Name of company：Fujikura Dia Cable Ltd.Location：Konwa Bldg. Tsukiji 1-12-22 Chuo Ward, TokyoRepresentative：President Tadatoshi Kuge
Outline of FDC after consolidation
Capital：5.4 billion yenDate of establishment：January 26, 2005Number of employees：Approximately 700
Name of company：Fujikura Cube Ltd.Location：Mutsuzaki 1440 Sakura City, Chiba PrefectureRepresentative：President Hiroyuki Mizuno
Outline of Fujikura Cube Ltd.
Capital：10 million yen (100% financed by Fujikura)Date of establishment：November 2, 2015Number of employees：10
Tele-communi-cations
Development of Anti-pollution Silicone Plug-in Terminal Module
Launch of Business Integration Launch of Business Integration Launch of Business Integration Launch of Business Integration with Fujikura Dia Cable Ltd.
Other
Establishment of Fujikura CubeOther
Fujikura News
4
2016 No.417Fujikura News
“Tsunagu” Technology New Product News
Fujikura Ltd.1-5-1, Kiba, Koto-ku, Tokyo, Japan 135-8512TEL. +81（0）3 5606 1112 FAX. +81（0）3 5606 1501Issue : April 2016, No. 417 Editor in Chief : Keisuke Okamurahttp://www.fujikura.co.jp
Sales Support & Branch Off ice Management DepartmentKansai Off iceChubu Off iceTohoku Off iceKyushu Off ice
+81(0)3 5606 1095+81(0)6 6364 0373+81(0)52 212 1880+81(0)22 266 3344+81(0)92 291 6126
2016
4
