Fuel injection in si engine by shubham sanjay sorate ph.no.8421592224
-
Upload
8421592224 -
Category
Engineering
-
view
353 -
download
0
Transcript of Fuel injection in si engine by shubham sanjay sorate ph.no.8421592224
ASEMINAR ON
FUEL INJECTION IN SI ENGINE
BY: MR.SHUBHAM.S.SORATE
INTRODUCTIONTransition of Fuel Supply System
Carburetor Port Injection
(MPFI)
Direct Injection
(GDI)
ADVANTAGES OF FUEL INJECTION OVER CARBURETOR
☼ Fuel injection has no choke, but sprays atomized fuel directly into the engine.
☼ Electronic fuel injection also integrates more easily with computerized engine control systems. ☼ Multi port fuel injection delivers a more evenly distributed mixture of air and fuel to each of the engine's cylinders.
☼ Sequential fuel injection improves power and reduces emissions.
Petrol injection system
Gasoline direct injection (GDI)
Indirect injection ( manifold injection)
Single point injection
Multi point fuel injection (MPFI)
Throttle injection Port injection
Throttle injection
Port injection
TYPES OF PETROL INJECTION SYSTEM
In indirect fuel is injected into the air stream before entering the combustion chamber.
And in direct injection system fuel is injected directly inside the combustion chamber.
Fuel injector
Indirect injection Direct injection
Combustion Chamber
Inlet valve
Single Point Injection systemThe earliest & simplest type of fuel injection,
single point simply replaces the carburetor with one or two fuel injector nozzles in the throttle body, which is the throat of the engine’s air intake manifold.
Single point injection system meters fuel better than a carburetor and is less expensive and easier to service.
Throttle Injection
The indirect injection can be classified as single point injection and multi point fuel injection.
The single point injection also called Throttle injection in which fuel is injected at one place in throttle body, and the mixture supply to different cylinders as shown in fig…
Port injectionIn case of Port injection also called multi
point fuel injection, air sucks through throttle body, and fuel is injected near inlet valve of every cylinder as shown in fig….
Multi Point Fuel Injection System(MPFI)MPFI system is widely used in petrol engine
in place of carburetor.Purpose of MPFI is supply proper A/F ratio to
each cylinder of engine.Fuel tank > Pump > High pressure petrol >
Distributor > Fuel injector > CylinderNow a days MPFI system control by Electric
Control Module (ECM).Ecm receives signal from different sensors.ECM receives signal and send to the solanoid
operated fuel injector to meter and inject right amount of fuel at right time.
There are different type of sensors in MPFI system.
1. Inlet manifold pressure sensor 2. Air flow sensor3. Engine speed sensor4. Throttle position sensor5. Coolant temperature sensor6. Inlet air temperature sensor7. Knock sensor8. Exhaust gas sensor
Direct injection (GDI)These systems inject the fuel directly into the
combustion chamber, either during the intake stroke or during the compression stroke.
There are two basic type of GDI, either injection of gasoline alone, or a duel injection of gasoline and air together.
Injection of fuel alone is usually done during the compression stroke and is somewhat similar to fuel injection in CI engine. Because of the very short time available for vaporization and mixing with air, very fine droplets of fuel are required, as are high turbulence and bulk mass motion within the combustion chamber
Injector pressure must be higher than that require for port injection.
This is because of the higher pressure into which the fuel is being injected, and because of the requirement for finer droplets of fuel.
Pressure required for fuel injection is above 40 to 65 bar.
Modern gasoline engine may utilized Direct injection using electric control.
Working of fuel injection in si engine
3.350Fuel Pressure (MPa)
Port InjectionIn-Cylinder Direct InjectionFuel System
StandardUpright StraightIntake Port
Flat top PistonCurved Top PistonCombustion Chamber
10.512.0Compression Ratio
Intake: 2, Exhaust: 2Number of Valves
IL-4Number of Cylinders
1834Displacement
81.0 x 89.0Bore x Stroke (mm)
Conventional MPFIGDIITEM
COMPARISON
Fuel injection in two wheelers
1.It uses advanced sensors and actuators to calculate and deliver the optimum amount of fuel to the engine – enhancing both performance and mileage.2. more responsive leading to quick initial pickup and delivering smooth passing acceleration.3. It achieves a 14% improvement* in fuel economy. 4. its intake/exhaust valve layout is designed to best match the hemispherical combustion chamber. In combination with the optimized intake and exhaust port shapes, this design increases combustion speed and helps achieve excellent combustion efficiency. The new engine further improves fuel efficiency and the feeling of acceleration while retaining the excellent performance qualities of the current FZ engine.
Advantages of Direct InjectionBettor vaporization
Higher volumetric efficiency
Easy cold starting
Lower exhaust emission
Higher efficiency and better mileage
ConclusionFrom this conclude that the fuel injection
system is more efficient than the conventional mpfi and diesel engines
It improves the engine efficiencyMore convenient to use than the diesel
engineIt gives better performance than the diesel
engine. Lower exhaust emission
References
[1]Kedzia, R., Okoński, A., „Układy paliwowe systemów wtryskowych silników z zapłonem iskrowym”, Poradnik
Serwisowy Nr 1/2002, Instalator Polski, Warsaw 2002, Poland [2]Kochersberger, K., Hyde, K. W., Emsen, R., Parker, R. G.„An Evaluation of the 1910
Wright Vertical Four Aircraft Engine”, AIAA-2001-3387, American Institute of Aero‐nautics and Astronautics, Reston 2001, United States of America
[3]Mason, F. K„Messerschmitt Bf-109B,C,D,E in Luftwaffe & Foreign Service”, Aircam Aviation Series No. 39 (Vol.1), Osprey Publishing Limited, ISBN 0-85045-152-3 Berk‐shire 1973, United Kingdom
[4]Kowalewicz, A.Tworzenie mieszanki i spalanie w silnikach o zapłonie iskrowym”, Wy‐
dawnictwa Komunikacji i Łączności, ISBN 83-206-0399-4, Warsaw 1984, Poland [5]Cygnar, M., Sendyka, B., “Determination of the Total Efficiency of Direct Injection SI
En‐ gine Working on Stratified Charge”,Wydawnictwo Państwowej Wyższej Szkoły Zawo‐
dowej w Nowym Sączu, ISBN 978-83-60822-46-3, Nowy Sącz 2008, Poland [6] „GDI – Gasoline Direct Injection. Nowy silnik benzynowy. Podstawowe informacje
tech‐niczne”, Technical information, Mitsubishi Motors, MMC Car Poland Co. Ltd., War‐saw 1998, Poland